Search Documents

By Yves Boissonnas, Marco Bettelini

"INTRODUCTION AND OBJECTIVES The operational safety of long and very long rail tunnels represents a key issue in all development stages, including design, construction, commissioning and operation. The spectrum of potential threats is very broad and challenging. These issues can only be mastered by means of a proper combination of a number of safety measures at various levels. This paper focuses on the specific safety issues and the extremely challenging conditions characterizing very long and deep tunnels. They include a significantly increased risk during operation that the incident train cannot exit the tunnel by its own means, long self-rescue and rescue distances, the presence of a number of trains, possibly mixed traffic as well as significant thermal issues. Amberg Engineering is strongly involved in the design and construction of most long and very long rail tunnels in Europe, including in particular the Gotthard Base Tunnel (GBT), Lyon-Turin Base Tunnel (LTF) and the Brenner Base Tunnel (BBT). The combined experience arising from these tunnels forms an invaluable body of expertise, which is summarized in this paper. The focus is on shared issues with practical relevant examples and project-specific solutions. Special attention will be devoted to the 57 km long Gotthard Base Tunnel, which will be operational by mid-2016 and will be the longest infrastructure tunnel worldwide. VERY LONG TUNNELS IN EUROPE Overview From the point of view of safety, tunnels in excess of about 20 km exhibit a significantly increased risk that incident trains could stop within the tunnel. This is related to the European Technical Specifications for Interoperability (TSI) on rolling stock, to be discussed in the chapter on rescue stations. This paper will specifically focus on the following longest tunnels in construction or operation, listed in Table 1."

Jan 1, 2016

By J. Loeb, R. Ramanathan, P. Cameron

All mining operations, including iron ore, maintain a focus of continuous improvement and asset optimisation in their operations. As all the operations in the Mine-to-Mill value chain are inter-dependent, available technologies that address efficiencies across the value chain are once again in the spotlight as companies are driven to improve productivity and maximise mine site profits to increase return on capital invested. Core to continuous improvement is the need to understand the baseline and the impact of changes to the process. In this paper, we discuss some of the key attributes in the mine to mill process, including their influence on productivity and cost, the need for direct measurement and areas where they should be applied. Many initiatives can be considered to improve mine to mill processes. Mining operations are planned and executed based on designs and models to achieve the operation’s objectives. However, there are many variables in the different parts of the value chain, such as blasting, material handling, crushing and screening. Measurement of the key attributes establishes the baseline for Mine to Mill (or Pit to Plant) performance which is necessary to understand the impact of any proposed improvements to the process design and execution and to monitor the outcomes on an ongoing basis to sustain the improvements that have been implemented. We have focused this paper on two types of measurement – blast movement and particle size of materials through the mine to mill process. Several innovative technologies are already available to measure these attributes and assist operations improve productivity and mine site profits.

Mar 2, 2022

By H. A. von Schonfeldt, H. Douglas Dahl

INTRODUCTION During the past decade, significant pro¬gress has been made in applying rock mechanics principles to mine design problems by a great number of researchers. Some of these new techniques have found their way into the engineering and planning offices of the operating mine. In spite of these advances, however, the application of rock mechanics in the day-to-day mine planning and design of our domestic coal mines is rela¬tively rare. There are a number of reasons responsi¬ble for this relatively slow progress, not the least of which is the question of how to measure the success or cost effectiveness of a sizable rock mechanics effort in an opera¬ting mine. Firstly, the properties of geologic materials generally vary over a wide range and it is, therefore, difficult to assess whether an improvement in the mining conditions is due to a design change or due to a change in the geologic conditions. A second reason for the slow acceptance of rock mechanics in engineering thinking is the fact that some of the concepts are quite difficult and that physical evidence of their validity to mine design is still rare. Thirdly, com¬munication between research, engineering and applications oriented people appears to function only intermittently. In our view, however, the most important impediment lies in the "state-of-the-art." Exactly how much can rock mechanics help the mine operator? The best that rock mechanics can do at present is determine whether one approach is better than another when weighed against some design objective (stress, strain, deformation). We cannot determine the abso¬lute best ground control design -- only what is better. If ground control is lost, the statement that "it's the best one we looked at" means very little to the harried operator. While the "state-of-the art" has advanced a great deal, it has certainly not been reduced to an engineering matter in that design hand¬books are available -- they are not. The success of a rock mechanics program, there¬fore, can be determined only over a long period of time of continuous effort.

Jan 1, 1977

By Meghan Murphy, Yiming Sun, Kush Chohan

DTX is a 1.3-mile-long rail extension being constructed by Transbay Joint Powers Authority to extend Caltrain rail service and future California High Speed Rail service to downtown San Francisco. It includes a 3,352-foot-long mined tunnel with a cross section varying from 50 to 60 feet wide and 43 feet high to accommodate two- and three-rail tracks. DTX will be excavated in mixed-face and Franciscan Formation with ground cover ranging from 40 to 85 feet. This paper discusses how mined tunnel design has evolved since the initial preliminary design phase over 10 years ago. The current design concept for tunnel construction is also discussed.

Jun 13, 2023

By David L. Daniels

The U.S. Geological Survey has for many years been flying and compiling aeromagnetic surveys. The aim is complete coverage of the United States, about half of which is presently done. Colored aeromagnetic maps at a scale of 1:1,000,000 are published as the states are completed; Minnesota and Colorado have been published. Michigan, Iowa, Nevada, Utah, Maryland and Virginia are presently being processed. Some of the most spectacular data collected to date is from the Piedmont of the Eastern United States. I am going to discuss a preliminary aeromagnetic map of the Piedmont region between New York and North Carolina, where coverage is nearly complete. This map has been compiled from many surveys. Flight spacing over Piedmont rocks is 1/4 to 1 mile with flight elevation of 500 feet above ground. The spacing over the Virginia Coastal Plain and Valley and Ridge regions is wider at 2 - 3 miles. Much of the data in Virginia has been produced by the Virginia Division of Mineral Resources. The map is colored on a spectral color scheme with red for the higher intensities and violet the low intensities. Each color represents a 100 gamma interval. Some of the highest intensities are beyond the range of the 13 colors - these are left white. It is necessary, of course, to remove first, the Earth's main magnetic field. The Geological Survey uses the International Geomagnetic Reference Field or IGRF (Fabiano and Peddie, 1969). The use of color in aeromagnetic maps is not new, but then not common. We have found that colored aeromagnetic contour maps are more useful by far than the uncolored versions because they allow the user to instantly compare intensities in widely separated areas and visualize long wavelength anomalies even when numerous short wavelength anomalies' are superimposed. One tends to see only steep gradients on uncolored aeromagnetic maps, the broad anomalies being quite invisible. We feel that colored maps take the place of various mathematically derived maps such as second derivative or averaged maps.

Jan 1, 1973

By Alper Kirmaci, Taghi Sherizadeh, Kutay E. Karadeniz, Dogukan Guner, Samuel Nowak

Injuries and fatalities resulting from roof falls are still a major concern in U.S. coal mines, and many researchers are focused on developing meaningful approaches to minimize this hazard. In the United States, coal mine roofs can vary widely in composition, geometry, and inherent heterogeneity, leading to a wide array of different roof fall failure types. Researchers frequently employ numerical modeling tools to reproduce this physical phenomenon and provide key guides to engineers regarding roof conditions and control as long as the input data and constitutive relations are appropriately selected. Simulating such complexity requires expertise and constitutive models that adequately simulate roof behaviors. However, the currently available constitutive models have shortcomings in capturing some of the roof fall failure types common in underground coal mines, such as guttering. A new constitutive model is developed to address the shortcomings of constitutive models commonly used for coal roof stability analysis. The constitutive model developed in this study combines the anisotropic-elasticity and nonlinear strain-softening responses. In addition, the developed constitutive model can simulate up to three different joint sets implicitly, allowing for use in both continuum and discontinuum settings, and can be used in both Lagrangian finite-volume and distinct element method codes of Itasca. First, the mathematical expressions of the model are provided. Afterward, the validation phase of the developed model that covers comparisons with analytical solutions and those of existing models (e.g., anisotropic elasticity, ubiquitous-joint, and bilinear strain-hardening/softening ubiquitous-joint plasticity) is presented. Finally, a hypothetical coal mine roadway facing high horizontal stress is simulated. The presented model successfully shows three distinct stages of a cutter roof in a shale roof: (1) initiation of shear cracks at the rib– roof intersection, (2) extension of cracks deeper into the roof (i.e., above the roof bolt length horizon), and (3) cantilevered roof. It is demonstrated that the presented constitutive model has the potential to help future researchers in simulating various roof responses.

Jul 1, 2023

By Timothy J. Orr, Jami M. Girard

A NIOSH study on occupational deaths between 1980 and 1989 indicated that in the United States, mining had the highest average annual fatality rate (3 1.9 per 100,000 workers) of any other major industry. Since "lack of training" was often cited as the primary cause of accidents, NIOSH has been investigating new methods for effective training. One such method is the use of low- cost, desktop computers to simulate a virtual mining environment. Computer-based training offers several advantages over conventional training because the computer programs provide a three- dimensional environment that allows the trainee to practice using evacuation routes, encounter mining hazards, and view mining operations without being exposed to any real danger. One major focus of the project is mine escapeway multiuser training using desktop virtual reality programs. Researchers have imported mine maps into the software for the purpose of practicing actual evacuation routes and procedures. Various scenarios for evacuation can be practiced in a three-dimensional computer simulation of the mine in a disaster situation, complete with smoke, fire, and other dangers. Depending on the trainee's job description (i.e., foreman, shift boss, beltman, etc.), certain tasks need to be performed in addition to navigating primary and/or secondary escape routes. Each scenario allows for individual or team-based training and provides a means to educate mine workers in hazard recognition and hazard avoidance. Using this program, mine workers can practice evacuating various mine layouts without the danger and expense associated with escapeway training in an actual underground mine. Each scenario can be changed to test the trainee's reaction in a variety of circumstances and run many times so the trainee can practice concepts. This training experience will help reinforce the knowledge acquired during more conventional classroom instruction, and the inherent flexibility of the program allows training materials to be tailored to meet the specific requirements of individual mines.

Jan 1, 2002

By Yi Luo, Jian Yang, Hua Jiang

Surface subsidence induced by underground coal mining activities, especially longwall mining operations, can cause various problems to interstate highways ranging from structural integrity to drivability to safety. Accurate subsidence prediction, correct influence assessments and effective mitigation measures are the keys to ensuring the safety of highway traffic. The surface subsidence prediction program, called comprehensive and integrated subsidence prediction model (CISPM), was developed based on the principle of influence function method and has been validated with a large number of subsidence measurements. In this paper, the techniques to use the predicted final surface movements and deformations for assessing their influence on the integrity and functionality of highway structures — such as road surface pavements, concrete slabs and transverse joints — vehicle dynamics, comfort level and drivability are presented. A number of mitigation measures to protect the highway structures and to ensure traffic safety are proposed, along with an application case.

By Jeremy Cawley, Jeff Murphy, Horry Parker, Brock Gaspar, Jake Keegan

The Lower Olentangy Tunnel project includes 47,000 cubic yards of planned ground improvement for earth pressure balance machine (EPBM) tunneling (5.2 km) and microtunneling (335 m) in glacial soils. Jet grouting started in late 2021 and will continue through 2023 to complete operations at 5 shafts, 14 safe havens, 5 watermain ground improvement zones, and a river crossing. Typical jet grout columns are installed at depths between 15–24 meters. Discrete soil-cement blocks range from 267–8,900 cubic yards in volume. This paper discusses the methodology, testing, and technical considerations associated with jet grouting operations in glacial overburden across an urban environment.

Jun 13, 2023

By Frank G. Horino, V. E. Hooker

INTRODUCTION The determination and use of mechanical properties of rock in engineering and rock mechanics are rapidly developing. Many of these properties are determined on intact rock specimens; thus, their application and repre¬sentation of rock mass properties may be limited. How¬ever, relative information often provides useful guidance in the solution to mine design and stability problems. Summarized in this chapter are some of the stan¬dardized techniques and procedures currently used to obtain these mechanical properties. Typical applications of the use of these properties are also presented. Stan¬dardized techniques include those advanced by the American Society of Testing and Materials (ASTM), International Society of Rock Mechanics (ISRM), US Bureau of Mines (USBM), Canadian Dept. of Mines and Technical Surveys, South African Institute of Min¬ing and Metallurgy, and other individual investigators. Information on the mechanical properties of rock and the behavior of the rock under a given system of stresses represents a necessary part of the information for rational engineering design for any given mining op¬eration. The mining method, the type and extent of sup¬port, the extraction ratio, the overall dimensions of the mine, and the orientation of the rooms and pillars are all decisions that are influenced by the mechanical prop¬erties of the ore, roof, and floor material under various stress systems and the magnitude and direction of the in situ stresses (Hooker, Bickel, and Aggson, 1972). Initial mechanical property information regarding a structure or mine property is generally obtained by two basic techniques: (1) static and dynamic property tests are conducted on intact and fractured rock specimens of exploratory drill core, and (2) dynamic properties are obtained by borehole logging techniques. When mining access becomes available, and as the mining horizon is expanded, additional information can be ob¬tained to verify preliminary mine design values. This chapter presents some of the standardized tech¬niques and equipment currently used in obtaining me¬chanical property data in the laboratory. The properties considered are: (1) uniaxial compressive strength of intact rock core specimens, (2) uniaxial compressive strength of rock cores containing planes of weakness, (3) triaxial compressive strength of intact rock core specimens, (4) triaxial compressive strength of cores with a plane of weakness, (5) Young's modulus, (6) Poisson's ratio, (7) density or apparent specific gravity, (8) modulus of rupture, (9) indirect tensile strength, and (10) creep characteristics. Where possible, an at¬tempt will be made to evaluate each property measure¬ment in relation to the problems of rock mechanics and application of results. TEST SPECIMENS The selection and care of drill core for laboratory testing require some consideration. It is recognized that laboratory-determined properties are not necessarily rep¬resentative of an in situ rock mass property. However, relative information between beds or zones of interest is still valuable information in selecting mining horizons and preliminary design criteria. To provide statistical data the number of drill core samples selected to repre¬sent each of the areas of interest should be from a mini¬mum of three to a maximum of ten test specimens. A judgment must also be made on site as to whether the recovered drill core should be wrapped and sealed in plastic to preserve moisture. On the one hand investiga¬tions of air-dried and saturated specimens have shown that moisture significantly affects the elastic properties and strengths of many rock materials (Obert, Windes, and Duvall, 1946; Colback and Wiid, 1965); on the other hand it is apparent that most core drilling is done with water which may saturate the specimen to a greater extent than in the in-situ condition. Whether or not the decision is made to retain the moisture, the core should be delivered to the laboratory as soon as possible after recovery for subsequent specimen preparation and testing. Specifications Shape: The shape of the specimens influences lab¬oratory testing in two ways: (1) time and cost of sam¬ple preparation and (2) strength of the material. Cy¬lindrical specimens of drill core are by far the least time-consuming to prepare for static or dynamic labora¬tory testing. In addition, the cylindrical shape lends it¬self to a more uniform stress distribution throughout the sample than other shapes, such as rectangles and hexa¬gons. The compressive strengths of various shapes have been studied (Grosvenor, 1963, and Price, 1960), and results indicate that the cylindrical specimens usually provide the highest strength for a given height-diameter ratio. However, reduction in strength from a cylindrical shape to a rectangular in situ pillar is not regarded as significant in relation to other considerations such as planes of weakness in a pillar or safety factors in the design process. Length-Diameter Ratio: The length-to-diameter ra¬tio, LID, has a significant effect on the compressive strength. Various recommendations have been made to use standard LID ratios ranging from 2 to 2.5 to 3 (ASTM, 1975c; ISRM, 1972). However, past work by others such as Obert, Windes, and Duvall (1946) has shown that excellent results can be obtained using LID ratios from 2 > (LID) > >/s. In selecting an LID ratio for testing, one should keep in mind the amount of material available for testing. In many instances, this may be limited. Thus, a shorter specimen such as 1: 1 LID may be necessary to provide enough test data for statistical analysis of results. Sec¬ond, it may be desirable to obtain elastic constants dur¬ing the test. This generally requires instrumentation such as linear variable differential transformers (LVDTs) or strain gages near the center of the specimen. In this case, an LID of 2.5 or 3 is desirable so that the instru

Jan 1, 1982

By Steve Kral

As the mining industry watches commodity prices continue to soar, the question on most everyone’s mind is how long will this upcycle last. The con-census among speakers and attendees at the SME Annual Meeting and Exhibit is that this cycle is sustainable. The buzz at the meeting was, of course, the current boom cycle the industry is in. Most agree that China’s huge appetite for mineral commodities is part of the force driving the upturn. But the improving economies of other developing nations also plays a role. However, along with the good times come challenges. Speakers at the keynote session addressed some of the challenges and offered their opinions on the sustainability of the boom.

Jan 1, 2006

By Harry Asche

Tunnels are frequently specified by owners to be designed to a structural code, often a bridge code. In the USA, AASHTO have created a tunnel code, based on structural principles, the AASHTO LRFD Tunnel Design Specification. The Load Resistance Factor Design method (LRFD) described in the AASHTO title is an approximation to the probabilistic design of structures, based on the independence of load and resistance. This methodology is well known to be problematic in geotechnical design, but it is widely used. The paper considers the difficulties of this approach and describes alternative approaches that would result in more appropriate designs for tunnels.

Jun 13, 2021

By Vinícius Resende Domingues, André Pacheco de Assis, Bernardo Cascão Pires e Albuquerque

"The increasing demand for underground works in urban centers, and in particular the need to build undercrossing tunnels, requires constant evolution in building techniques in order to achieve success and safety. In the case of Brasilia, capital of Brazil, in order to preserve an important avenue (Eixo Monumental), where are located many historical monuments, the construction of a tunnel was envisioned as an option to interconnect the National Stadium (on one side of the avenue) to the Convention Center Ulysses Guimarães (on the other side). The excavation design is comprised of a coverage smaller than one diameter, height of 7.5 m, width of 9.0 m and length of 25 m. In order to enable a negligible influence on the avenue’s usage, the structure is designed as a portico system composed of pipe canopy. In this context, this study presents the portico analytical solution computed with the aid of the software Mathematica and a numerical solution using the software ABAQUS. INTRODUCTION Undercrossing tunnels are increasingly common in urban centers as alternative roads or as access to underground works of large dimensions (stations and parking lots). The geomechanical conditions of the soil mass, not always favorable, and the low distance between tunnel’s ceiling and the surface require intense treatment of the soil massif and execution of a rigid support system. The importance of the road just above the undercrossing tunnel emphasizes the need for a highly competent monitoring system because existing structures require minimum allowable displacement and do not allow the interruption of traffic. The soils that are excavated for the construction of undercrossing tunnels are composed, in most cases, of layers of fill and / or soft soil or weak rock, showing stability problems when subjected to tunneling operations. The combination of low coverage and week ground is solved by soil improvement techniques and strengthening of the excavated cross-section with further advance with the so-called New Austrian Tunneling Method (NATM). Another option is to build structural frames that support the surface. In this research, and based on the context of a case study, we propose the study of the construction technique comprising a portico structure composed of pipe canopy. For this paper, the technical standards used are the Brazilian ones as the case study refers to this country."

Jan 1, 2016

By Arash Dahi Taleghani, Pooyan Asadollahi

Slurry walls, also known as diaphragm walls, are commonly used as temporary and/ or permanent support of excavation for construction of shafts in soft ground. Through case history, this paper demonstrates economical benefits of disregarding long-term structural contribution of the slurry walls particularly in severe environmental condition. In addition, for temporary slurry wall shaft systems, possibility of using steel fiber, synthetic fiber or additives in lieu of temperature/shrinkage reinforcement is discussed with detailed analysis. Finally, the paper will be concluded by introducing unreinforced slurry wall shaft system using newly developed/patented concrete additive.

Jun 13, 2021

By C. Zhou, J. Srednicki

Electronic systems have been increasingly used in underground mines to improve mine safety. These electronic systems emit electromagnetic (EM) energy which can adversely impact the performance of other electronic systems nearby and thus should be characterized. Researchers at the National Institute for Occupational Safety and Health (NIOSH) characterized the magnetic fields emitted from devices that can potentially interfere with the performance of proximity detection systems (PDSs) and compared the emission levels of these devices to the susceptibility of PDSs. In this paper, we present our measurement results pertaining to this effort. Particularly, magnetic fields emitted from the different orientations of a powered air purifying respirator (PAPR) and two lite trackers are evaluated based on the RE101 protocol specified in the MIL-STD-461G standard. The results show that both devices emit strong magnetic fields which strongly depend on the orientation of the devices. At some frequencies, the maximum emission levels from the two devices exceed both the emission limit given in MIL-STD-461G and the maximum magnetic fields that a PDS can withstand without a failure. The results and findings in this paper can help the mining industry better understand electromagnetic interference (EMI) underground and provide critical scientific data that support mining-specific recommendations to address EMI-related challenges.

Feb 1, 2023

By Qingming Feng, Jinhong Zhang

This study investigates the application of fly ash as a high-strength, water-resistant precast construction material through geopolymerization. The experimental results show that working conditions such as water content, sodium hydroxide (NaOH) concentration, curing temperature and curing time significantly affect the mechanical properties of the geopolymer matrix. Through optimization, compressive strength above 100 MPa was achieved, and the optimum working conditions were found to be NaOH concentration of 10 M, water content of approximately 14 to 15 percent, and curing at 90 °C in an oven for one day or at ambient condition for three weeks. Water-soaking tests show that the geopolymerization product has high water resistance without losing noticeable compressive strength even after one month of soaking time. The findings provide a novel method to apply fly ash as a high-strength, water-resistant precast construction material.

By John Kuyt, Zili Li, Michael Mooney, Michele Mangione

"INTRODUCTIONTwin bored tunnels are commonly used for a variety of road and tunnel projects throughout the world. A major component of these twin tunnel projects is the construction of connecting cross passages that provide emergency access between tunnels and space for tunnel service equipment. Cross passages can present significant geotechnical risk and technical challenges to a project – support systems must be considered for redistributing loads around the mainline tunnel openings and supporting new loading resulting from excavation activities. Additionally, cross passages pose risks to construction schedule and cost because of their sequencing at the end of construction, so mitigation of schedule overruns can be critical. By observing field instrumentation data records from completed projects, a betterunderstanding of the force development in each temporary structure can be achieved with indication of which structures are the most critical to support ground loads.This paper discusses the data obtained during the Brisbane Airport Link construction project, a road tunnel located in Brisbane, Australia. Strain gauge instrumentation data from the precast segmental lining and propped opening steel sets is presented with relation to the construction sequence and local geology. Interpretations and conclusions based on the observed trends are proposed, with several key mechanisms affecting the loading and unloading identified.Brisbane Airport Link Project OverviewThe Brisbane Airport Link project in Brisbane, Australia, connects central Brisbane to the airport located northeast of the downtown with over 7km of twin-bore road tunnels, two lanes each, with several caverns, interchanges, and access ramps constructed along the alignment to connect to other key routes in the city. The project was executed under a Public-Private Partnership (P3) scheme, funded and operated by the consortium BrisConnections. The main contractors were a joint venture of John Holland and Theiss, while the design was carried out by Arup and Parsons Brinckerhoff.Construction of the tunnels was conducted using a combination of 17 roadheaders and two 12.5m double-shield Herrenknecht TBMs [1]. The TBMs were used in EPB-type closed mode for the initial portion of their drive, starting at the northeast end of the alignment. Tunneling started in soft ground, weathered rock, and mixed face conditions initially, progressing to competent sedimentary rocks as the drive continued. Support was accomplished using a 12.1 m diameter steel fiber reinforced concrete (SFRC) segmental lining installed behind the TBMs in a 9 segments + 1 key arrangement. The innovative design of these segments is detailed in the paper by Harding and Francis [2]. Ancillary roads and underground interchange caverns were constructed by sequential excavation techniques using roadheaders, accounting for nearly half of the total underground excavations."

Jan 1, 2016

By Dieter Loh, Mathias Knoll, Florian Werres

When a new tunnelling project starts, it has been a vital tradition for decades to cast and erect master rings horizontally on a flat surface to demonstrate the compliance with dimensional tolerances. Some tenders ask for the erection of two or even three rings upon each other or repeated master ring erections at intervals throughout the project. Especially for large diameters, this is a challenging and risky task for the workforce in the segment factory. A truck-mounted crane is often necessary, and in some cases it can take up to a week to complete a master ring. The concept of virtual rings has the potential to replace this tradition by assembling master rings digitally instead of physically. This is based on a best-fit approach, considering the 3D coordinates from laser tracker measurements of segments or segment moulds. Building a virtual ring, a sub-millimeter accuracy can be achieved, the alignment of neighboring circumferential and ring joints observed, and the fit of bolt holes checked. The traditional method, on the other hand, is discussed controversially despite the significant amount of work and risks—particularly as the horizontal position of the ring and absence of gaskets do not simulate the reality in the excavated tunnel. This paper will highlight the technical aspects of virtual rings, as well as their pros and cons, illustrated by a case study from London Thames Tideway where a total of 30 physical master rings could be replaced by virtual rings.

Jun 13, 2023

By Inoka E. Perera, Robert Hildebrandt, Gerrit V. R. Goodman, Krzysztof Cybulski, Zdzisław Dyduch, Michael J. Sapko, Marcia L. Harris

To prevent coal dust explosion propagations, rock dust needs to be lifted and suspended in the air with the coal dust during an explosion. The addition of anti-caking agents prevents caking of rock dust in the presence of water. Mining and rock dusting processes can frequently create alternating layers of rock dust and float coal dust on mine surfaces. For this test series, a thin layer of coal dust was distributed on top of a layer of either treated or non-treated rock dust in the Experimental Mine Barbara, Poland. The experimental results compare the effectiveness of treated and non-treated rock dusts to attenuate a propagating coal dust explosion initiated with either strong or weak methane explosions. Experimental results indicate that the treated rock dust performs better than non-treated rock dust in arresting a propagating explosion, especially in the presence of moisture.

Jan 20, 2020

By Robert Cook, Valeria Zarate, Jason Hallowell

The long hole open stoping (LHOS) method is widely used in underground mining. While methods to predict stable stope geometries are well established, the ability to maintain a stable back often assumes effective ground support across the full stope span. The efficacy of the support strategy is dependent on rock jointing, quality, density, top cut width and height, and the type, amount, and orientations of bolts installed. However, it is becoming increasingly common for operators to assume narrow top cuts in service of wider stope spans with minimal bolting coverage. Failure to account for the required top cut drift size and support requirements can ultimately lead to raveling type instabilities along stope shoulders that result in back collapse. A new method has been developed to evaluate the minimum top cut dimension necessary to accommodate wider stope spans with various rock bolting configurations. Due to the economic impacts of top cut development and support, this is a critical consideration in the accurate costing and scheduling of a LHOS operation. Tables 1 lists the acronyms are used throughout this paper.

Feb 1, 2025