Search Documents

By V. Adamek

The specific lithological conditions over the Pittsburgh coalbed, highly resistive limestone and sandstone units with relatively shallow overburden, prevent the use of any predictive method as developed for European conditions. This paper describes the development of a subsidence precalculation methodology suitable to the mining-geological conditions in the Northern Appalachian Coal Field. It has been found that due to lithological conditions over the Pittsburgh coalbed the subsidence coefficient varies within the area of the subsidence trough. This is different from the European conditions where the subsidence coefficient is considered to be a constant. The effects of lithology, in-the form of a variable subsidence coefficient, have been separated for each test site by introducing a correlation between hypothetically homogeneous overburden and existing lithological conditions, while providing for different mining conditions. Field data from eleven Bureau longwall panel studies were used in the regression analysis. For each panel the characteristics of the variability of the subsidence coefficient along individual profile lines were defined. Regression analysis of the subsidence coefficients from all test sites on the location relative to the edge of the panel has yielded a third degree polynomial equation with a coefficient of correlation of 0.9999. All sensitivity tests have shown good results.

Jan 1, 1985

By Clark Harrison

It is not uncommon for overall quality of coal from a mine to deteriorate as the mine is developed or for an improved-quality coal specification to be imposed during the life of the mine. Either of these conditions typically results in management pressuring mine personnel to take greater care in delineating the seam from top and bottom rock. When mining and seam conditions require a portion of the seam to be removed to ensure sufficient rock is removed to meet the quality specification, physical-coal cleaning may become economically competitive with in-pit seam grooming. The additional cost of coal cleaning may, in some cases, be justified by permitting higher recovery of the coal seam than is possible when cleaning the seam with excavators in the pit. This paper compares projected coal cleaning results with present in-pit grooming techniques and reports the economic results.

Jan 1, 1987

By Rees D. Groves

Cement copper is ordinarily converted to marketable metal by processing in a conventional smelter and refinery. Because of rapidly increasing cement copper production and limited excess smelting capacity, other techniques were investigated for preparing marketable copper products. One route was to make copper powder for industrial use. The process scheme employed flotation for rejecting the bulk of the impurities, acid leaching to remove residual iron and aluminum, reduction sintering to eliminate oxygen, and grinding to obtain powder. Another route was to sinter the floated and leached copper into the form of anodes and electrolyze these to yield refined copper cathodes. At a current density of 30 amperes per square foot, power consumption for electrorefining was 185 kwhr per ton of copper. The feasibility of preparing commercial-size anodes by sintering is still to be assessed.

Jan 1, 1970

By Hou Xilun

Three production methods of rapid cold bonding and low temperature bonding pellets using sponge iron powder as a binder have been successfully developed. These methods differ from ordinary bonding method by no addition of salt and other catalyzers, no corrosion of equipment and no pollution of environment. Mechanism of pellet bonding is studied. Experiment shows that these pellets have good metallurgical properties. A semi-industrial test has proven the laboratory results, with the production of metallic pellets continuous and stable. These methods are substituted for traditional high temperature firing of oxidized pellets in direct reduction. As a result, the plant for oxidized pellets can be saved and substituted for grate in the grate-kiln system. Thus, 20% of the investment could be saved. Production cost may also be decreased. The production of cold bonding pellets does not need additional area.

Jan 1, 1980

By John A. L. Campbell

Surface dependent processes, such as froth flotation and flocculation, are important or potentially important techniques for combating some of the current major problems in coal preparation. In order to correctly apply or imporve a surface dependent process, it is of paramount importance to understand the interfacial phenomenon, especially the double layer properties, exhibited by the solid. The specific objective of this research was to determine the properties of the bituminous coal/liquid interface by an electrokinetic method, streaming potential, and to relate the findings, wherever possible, to the existing unit operations of froth flotation and flocculation. The electrokinetic properties of both the whole coal and its lithotypes were investigated. As part of the total investigation, the role played in the double layer by the reagents commonly employed in the surface dependent process was also established (1). These data will be presented at a latter date.

Jan 1, 1969

By Donald B. Buddecke

The large walking dragline has been the most commonly used overburden-stripping equipment in Texas lignite mines. These draglines, operating on the highwall side of the pit, can excavate to a depth of 45 m. Considerable overburden rehandling is required beyond 30 m and may reach 100 percent by 45m. As pit depth increases, dragline operation also becomes more complex, with two or three passes being necessary to make a cut 30 to 40 m wide. Multiseam operations also require extra passes. At pit depths greater than 45 m, the dragline must be operated also from a spoil bench. This can be difficult in the unstable alluvial deposits in which lignite occurs.

Jan 1, 1985

By David L. Martin

This paper discusses the development of a SLAM II* simulation model with imbedded optimization modules designed M evaluate mineral exploration and exploitation strategies. The model traces through a sequential exploration program, evaluating each deposit site based upon geologic information and potential profitability of the site. At a specified time during the simulation, a new production plan is developed for currently producing deposits which takes into account the planning horizon and deposits which are currently being explored. Potential uses of the model by geologists, engineers, and management decision makers include setting corporate objectives and policies on exploration and production. The model is also useful for testing past decisions to evaluate decision making criteria and evaluating mineral deposit profit potential.

Jan 1, 1983

By Allen D. Graham

The coal industry in South Africa is briefly outlined. Test- work carried out on bulk samples of coal in the laboratory and used in the design of the Van Dyks Drift washery are described. Factors affecting the selection of equipment and the designed capacity of the plant are discussed. A description of the crushing plant, washery and load out section is given together with performance data obtained in the final acceptance tests. New features incorporated in the Van Dyks Drift plant and in more recent plants of the Group are outlined.

Jan 1, 1982

By Daniel R. Walton

This paper covers several points of interest to mine engineers and planners involved in evaluating or conducting geostatistical coal reserve estimates. In particular, the ability to optimize borehole drilling locations and minimize drilling costs is addressed. Also discussed is the concept of confidence intervals for estimated coal characteristics obtained through geostatistical estimates and their importance in decision-making for mine planners. Finally, a discussion is presented on how geostatistics enables identification of invalid data points and actually forces strict attention to data editing and proper geologic interpretation.

Jan 1, 1982

By S. Hardcastle

Tele-remote operation of production equipment from surface will change the design criteria for underground mines. And for ventilation, with machine operators on surface, conventional planning to dilute and remove pollutants can become redundant. Natural Resources Canada with industrial partners are investigating what will be the new environmental design criteria. Additional complications include new mining equipment being designed without standard services and mines’ desire to eliminate conventional auxiliary ventilation. Findings to date show the cooling of equipment’s hydraulic systems to be the most demanding element, especially in dead-ends and when stationary. Consequently, revised ventilation based heat control strategies for equipment are being developed for the automated mine of the future.

Jan 1, 2001

By Michael Forbes, Rick Jeuken

The challenge of managing geological uncertainty in mine planning is central to optimizing resource extraction while minimizing risks and costs. This paper introduces a novel approach to coal mine planning by integrating chance-constrained programming to address the uncertainty inherent in mining operations. The main takeaway from this work is the demonstration that focusing on reducing the variance of high-quality coal blocks, rather than low-quality ones, can lead to better blending outcomes, higher profitability and more efficient resource utilization. The study presents a case study of a coal mining operation, using chance-constrained programming to manage the uncertainty surrounding coal property predictions, specifically the predicted coke strength after reaction (CSR).

Jan 1, 2025

By Klaus Grebe

Recent investigations by Mannesmann Research have shown that disintegration of sinter with widely varying quality levels is subject to a much more complex set of influences than was previously assumed. It was confirmed that disintegration at temperatures between 300 and 600 °C is triggered by the degradation of hematite. The specific tendency of hematite to disintegrate is, however, not constant: sinters containing the same amount of hematite can show widely differing disintegration tendencies depending upon structural homogeneity, porosity and gangue quantity. Especially sinters with heterogeneous structures transmit stress to the hematite phase and this favours disintegration. Another factor is the brittleness of the glassy silicate phase, which can be influenced even by small modifications of minor gangue constituents.

Jan 1, 1981

By E. W. Sawyer

Gelling-grade attapulgite and sepiolite clays are employed as thickening agents for the preparation of ionically contaminated drilling fluids where the use of fresh water clays are unfeasible or impossible. Attapulgite and sepiolite are nonswelling clays that can be dispersed and reflocculated by mechanical and chemical means to increase the viscosity of fresh water, salt containing waters, gypsum contaminated waters and fluids containing cement. Such gelled systems are quite stable in viscosity properties and can be further treated with other necessary additives such as thinners, water loss reducers, weighting agents, surfactants, etc. Many of the oil well drilling fluid practices have influenced such technologies as water well drilling, foundation drilling and waste disposal. The use of salt water gelling clays in these fields will be described and compared to oil well drilling.

Jan 1, 1986

By S. R. Dismukes

Mining is likely to be targeted by The United States Environmental Protection Agency (“EPA”) as one of its key enforcement targets for fiscal year 2002-2003. Identifying the mining industry as an enforcement target, coupled with an increase in enforcement activity in recent years, places each mining operation at increased risk of receiving enforcement attention. A properly developed and implemented Environmental Management System (“EMS”) tailored for your operation is invaluable in reducing the risk of incurring liability for non-compliance. At the heart of an effective EMS is an audit program that checks the company’s compliance with environmental requirements. In addition, audit privilege (in select states), voluntary self-disclosure, and the attorney-client privilege serve as very effective tools for managing those liabilities that may arise during auditing a well-developed program. Of course, these latter tools are effective only if the auditing program is properly structured and properly managed. EPA and some states also provide varying degrees of immunity for environmental violations that are voluntarily disclosed in writing by the company. However, self-disclosure laws and policies typically prescribe stringent requirements for parties seeking to take advantage of them. For example: U.S. EPA has recently extended the time period in which to provide full written self-disclosure to 21 days. However, U.S. EPA’s revised Self-Disclosure guidance also addresses when a company obtains knowledge of a violation for purposes of triggering the 21-day clock and specifically extends the knowledge requirement to include the company’s agents and consultants. This expansion increases the difficulty companies may have in clearly defining and managing when they obtained knowledge. This difficulty increases the importance of managing factual development and the strategic use of other

Jan 1, 2001

By M. M. Rajkovich, L. Adams, J. J. Zaluski, S. Gardner

In 1998, Kentuckians for the Commonwealth filed an Administrative Petition with the Kentucky Natural Resources and Environmental Protection Cabinet to designate 8,903 +/- hectares (22,000 +/- acres) on Black Mountain, which contains the state’s highest point, as unsuitable for mining. A fast track legislative process was triggered which could have "taken"100 million tons of coal reserves or, in the alternative, imposed severe restrictions on mining. Even with all parties represented by reasonable individuals, this process can be extremely cumbersome and expensive. The legal and technical preparation for this unusual hearing process as well as issues and strategies of the negotiated resolution are reviewed.

Jan 1, 2000

By Roy A. Koski

This paper describes variations in feed characteristics, preparation techniques, response to induration and product quality in pelletizing magnetite concentrates, earthy hematite ore fines, and specular hematite concentrates in grate kiln systems. The Cleveland-Cliffs Iron Company manages plants processing these various materials on the Marquette Iron Range in northern Michigan. The operations include the Humboldt Mining Company, Marquette Iron Mining Company, Empire Iron Mining Company and the Pioneer Pellet Plant. The combined output of the operations is approximately 9,000,000 long tons per year. The Humboldt Mining Company, owned by Ford Motor Company and Cliffs, produces pellets from a specular hematite concentrate. The Empire operation, which processes magnetite ore, is owned by Inland Steel Company, McLouth Steel Corporation, International Harvester and Cliffs. The Pioneer operation, which processes earthy hematite ores, is a joint venture of Republic Steel Corporation, McLouth Steel Corporation, Bethlehem Steel Corporation and Cliffs. The Marquette Iron Mining Company, owned by hones and Laughlin Steel Corporation, International Harvester, Wheeling-Pittsburgh Steel Corporation and Cliffs, produces pellets from specular hematite concentrate at the Republic Mine and Eagle Mills Pellet Plant. With the exception of the Eagle Mills plant, the operations employ the grate-kiln pelletizing system. Descriptions of the Empire, Pioneer and Republic operations, which have a combined capacity of 7,200,000 tons per year, are given in the paper.

Jan 1, 1969

By Jonas Svensson

The Grangcold Pellet Process - for which patents have been applied or already granted in a number of countries - uses a hydraulic adhesive such as Portland cement, slag cements, pozzolanic cements, etc., for the production of cold bonded pellets. The idea of using a hydraulic binder for the agglomeration of iron ore fines is not new. Portland cement was proposed as an adhesive for cold bonded iron ore briquettes in patents granted more than 50 years ago (1). In a report on the briquetting of iron ore fines, published in Stahl and Eisen 1959 (2), it is stated that briquettes bonded with Portland cement are used on a small scale at on ironwork in Germany. According to the report, the briquettes showed excellent strength in the blast furnace although their general use was made impossible because they required a long hardening time, during which they are sticky, soft and difficult to store and handle. The Grangcold Pellet "recess has overcome this particular disadvantage by mixing the balls with a suitable amount of the balling concentrate before storing them. The pellets are embedded in the concentrate during storing in such a way that they are isolated from each other and thus prevented from sticking together to form clusters. Thanks to the embedding concentrate, the pellets are subjected to a more or less uniform pressure from all sides which does not deform them. Thus the mixture can he stored in a stockpile or in a silo until the pellets have hardened sufficiently. The concentrate is separated from the pellets by means of screening. The concentrate is returned to the balling operation and the pellets are either shipped to the blast furnace or stored for final hardening.

Jan 1, 1969

By Young C. Kim

Use of geostatistics to solve mining problems is gaining importance as the cost of developing new mines is increasing and there is a need to mine more marginal deposits. But, until recently, coal companies have shown little or no interest in geostatistics. However, the stringent quality controls on coal burning has led to a surge in interest in improved methods for estimating clean coal characteristics. Until now, most of the geostatistical applications have centered on the problems of estimating in-situ coal characteristics (Sabourin, 1975; Wood, 1976, 1979; Fang and Stark, 1976; Pauncz and Nixon, 1979; and Knudsen et al., 1980). Little work has been done in applying geostatistics to coal washability, except that by Armstrong (1980). Applying geostatistics to coal washability basically means the estimation of cleaned coal characteristics, with the aid of geostatistics. Cleaned coal estimation plays a very important role in overall emission control strategy, as can be seen by the general flow diagram of such a strategy shown in Figure 1. The scope of this paper is limited to one aspect of the overall emission control strategy shown in Figure 1; namely, the prediction of cleaned coal characteristics using geostatistics.

Jan 1, 1982

By James E. Lonergan

Linear goal programming is a multi-objective optimization technique where the constraints of a linear programming formulation of a problem are considered as additional objectives. The optimal solution is the one that comes closest to satisfying all the objectives. An interactive computer program was written to utilize this technique in solving the feed blending problem faced by power plants de- pendent on multiple sources of coal supply. This program determines the amount of coal from each supplier to utilize in the blend. Examples of the use of the program in both long and short term coal procurement planning scenarios are given.

Jan 1, 1984

By Yao Dun-Pu

Solution mining, sometimes also refered to as chemical mining or bacterial mining, is an innovative technology which, by making use of proper chemical reagents and taking advantage of bio-chemical action of some micro-organism species, can dissolve effectively most. desirable metallic values from ores and then extract them profitably from the resultant metal-bearing solution by suitable means to form the metal product it is more preferable to the conventional mining methods, not only because of its capability to improve working conditions and minimize environmental problems either underground or on surface, but also for its amenability in particular, to exploit low-grade or submarginal ore bodies, or those deposits which are too deep-seated to be mined out economically. Furthermore, it also provides a potential approach to win metals directly from their ores or ore-deposits in-situ by more simplified methods and at a lower cast than the conventional mining-milling-smelting process would do previously. Hence, in developing countries such as China, it will most, probably become a new mining tool of great promise. (1)

Jan 1, 1981