Search Documents

By M. K. McCarter

In 1963, a major expansion program at Kennecott's Bingham Canyon mine converted rail operation in the upper portion of the pit to truck haulage. Since that time truck-haulage capacity has increased to about 272 000 Mg (300,000 tons) per day. The majority of this production is waste material which is deposited in monolithic dumps located on the eastern slopes of the Oquirrh Mountains. The largest of these dumps, referred to as Copper Notch and Keystone, measures approximately 1830 m (6000 ft) in length, from 180 to 300 m (600 to 1000 ft) in height, and contains some 430 Tg (470 mil lion tons) of waste. The height, structure, rapid rate of growth, and anticipated leaching suggested the possibility of dump failure. In order to evaluate this possibility, an outside consulting firm was retained in 1966 to investigate the stability of the growing dumps. Their investigation indicated that, other than superficial movement, the waste dumps would be stable under static loading, and that soil distribution was not continuous enough to sustain massive foundation failure. Since this investigation, however, several failure processes have been observed. Crest settlement occurs frequently in response to compaction and over-steepening in the upper portion of the dump surface. Over-steepening results from accumulation of fines near the crest caused by natural segregation. Normally, coarse material, near the base of the dump, exhibits an angle of repose near 0.65 rad (37"). The fine material, however, stands as steep as 0.75 rad (40"). Periodic equilibrium adjustments cause stepwise settlement (Figure 1) of the dump surface and occasional sloughing of the protective berm. Routine surface preparation by dozers and graders and frequent inspections by supervisory personnel have proven adequate in preventing problems associated with this form of crest instability.

Jan 1, 1976

By Arthur R. Still, Paul A. Bailly

5.1-PURPOSE, PROCEDURE, METHODS, MANAGEMENT Exploration can be technologically defined, with regard to the discovery of new mineral deposits, as all the activities and evaluations necessary before an intelligent decision can be made establishing size, initial flowsheet and annual output of new extractive operations. The purpose of mineral exploration is the discovery and acquisition of new mineral deposits amenable to economic extractive operations now or in the future. A prime objective of mineral exploration, however, is to find and acquire a maximum number of such mineral deposits at a minimum cost and within a minimum time. Immediately upon the heels of a successful ''exploration" discovery follow activities called, first, development, then operation. Under U.S. Internal Revenue Code regulations (Secs. 1.615.1 and 1.616.1) in effect at the time of this writing, which state that the "development stage" has been reached when "deposits of ore or other minerals are shown to exist in sufficient quantity and quality to reasonably justify commercial exploitation by the taxpayer," exploration in the technological sense may well continue after a mineral property has entered the "development stage" as defined for tax purposes. In many instances continued exploration, after reaching the tax defined "development stage," has disclosed additional reserves which justify a much larger, more efficient and more profitable operation than that which would constitute the minimum feasible. Even after a mine goes into production, continued ore search generally will increase the reserves, either justifying expansions in plant capacity or prolonging the life of the operation, but this work (actually "exploration") is normally considered, for bookkeeping and tax purposes, a part of mine development. Each exploration entity defines its own objectives in terms of acceptable mini- mum rate of return on investment for any deposit found and retained, and in terms of which commodities, and markets, are to be involved. For these reasons, exploration programs, and aims, will vary over a wide range, although all have the common objective of endeavouring to create new profit centers for the future. 5.1.2-EXPLORATION METHODS Exploration has evolved in the past several decades into a highly sophisticated and expensive endeavor in which large corporate entities, or subsidaries, normally are directed and staffed by highly trained exploration specialists. In some instances consultants, with expertise in a given field, are utilized to the benefit of such corporate groups. The "grasshopper" approach to exploration-searching only for outcropping minerals and/or investigating only mineral prospects offered by the discoverers of such outcrops has given us most of the past and present mines in the US., but this method is rapidly approaching the point of diminishing returns in areas that have been thoroughly prospected for currently marketable commodities. With

Jan 1, 1973

By H. Dho

The role of sodium silicate in the anionic flotation of a Florida phosphate ore was investigated using laboratory continuous flotation tests, frothability tests and SEM observations. In the absence of sodium silicate, Ca++ promoted the unwanted activation of quartz by forming calcium bearing precipitates. The addition of sodium silicate enhanced the flotation efficiency through: (1) the removal of impurity minerals and calcium-bearing. precipitates from quartz surfaces by dispersion, (2) drier and more persistent froths stabilized by oily droplets containing calcium silicate precipitates, and (3) higher specific flotation rates of phosphate relative to quartz, leading to faster flotation rates and increased selectivity of separation.

Jan 1, 1990

By Fred D. Wright, Stefan H. Boshkov

12.1-BASIC AND PARAMETRIC CRITERIA IN THE SELECTION, DESIGN AND DEVELOPMENT OF UNDERGROUND MINING SYSTEMS STEFAN H. BOSHKOV AND FRED D. WRIGHT The criteria governing the selection of an underground mining system relate to several factors the importance of which varies with geographic location, the state of development of the industrial technology, the economic climate in the Nation and, perhaps, in the world-all these as functions of time. Thus, the best choice of a mining method depends upon sets of definable and undefinable values for numerous factors that may be considered fixed at the precise point in time. Subsequent changes in economic and/or technological developments may necessitate modification or complete revision of the existing mining system. A classification of criteria for selecting a mining system must be based on the broadest definitions. Specific cases may present simple solutions or pose very intricate questions, the answers to which are frequently based on judgment rather than explicit logically reasoned and derived results. Specific criteria may be of negligible consequence in some instances and of overriding importance in other cases. It would be foolhardy to attempt to point out, in the limited space available, all possible variations and interplay of factors, as well as to define the setting in which this interplay can take place. The reader is, therefore, referred to the case histories described in the subsequent parts of this section where actual practice will point out the variability of the problems encountered in the selection of a mining method. A popular thesis suggests that the proper approach to selecting the method of mining should be rooted in the inverse solution, whereby the limitations of the various methods in use serve as criteria to eliminate most of these methods from consideration in the specific case. This narrows the ultimate selection to one or perhaps two most appropriate methods. At this stage, a critical comparison analysis will lead to the ultimate choice. Although such a negative approach un¬questionably is valid in discarding obviously inapplicable mining systems from consideration, it falls short in defining the best system, which in practice quite often turns out to be a variation of a textbook standard, or a combination of two or more such standards. Because the deployment of capital and manpower over a long-term commitment closely follows the selection of the mining system, the decision-maker can well afford to spend a great deal of time and effort in evolving the optimum solution for the peculiarities of his specific case. Within the basic engineering tenets of economy and safety to which the design of a mining system must adhere lie numerous factors of constraint which may be grouped, somewhat arbitrarily but for ease of discussion, into several categories. The criteria that enter into the choice of a mining method derive from the following groups of factors: 1. The shape, size and spatial position of the ore deposit.

Jan 1, 1973

By Yvon H. Poirier

Carbon addition in the oxide pelletizing process is a big concern at the Sidbec-Normines pelletizing plant since 1976. Laboratory pot-grate testing carried out before the initial start-up of the Port-Cartier plant indicated that the nominal pelletizing grate capacity could be increased by fifteen percent with a suitable carbon addition. Also an improved induration cycle offered the possibility of a significant energy reduction within the process with no adverse effect on pellet quality. A one month plant scale program duplicated the lab test results and confirmed the anticipated cost saving by using these techniques. Since March '80, Sidbec-Normines use coke addition as a current operation. This paper reviews briefly earlier laboratory and in-plant test work carried out to investigate the effects of adding carbon materials to the Fire Lake hematite concentrate, and presents operation techniques and plant results of carbon addition in the Port-Cartier pellet plant.

Jan 1, 1982

By George A. Snyder

The presence of moderate to high concentrations of colloidal clays in coal preparation plant waters can cause serious operating and economic problems for a coal company. Among the host of possible problems are the following: 1) Poor separation of clays in the plant thickener, resulting in: a) Increased ash in the clean coal. b) Increased specific gravity of the wash water and decreased coal recoveries at the desired quality. c) Increased thickener operating costs in trying to overcome the problem. 2) Decreased solid concentrations in the thickener underflow and increased pumping requirements to meet solids withdrawal requirements.

Jan 1, 1979

By K. C. Vories

Surface mining and reclamation has the potential to at least temporarily increase surface runoff and resultant erosion and gully development. This increase in erosion is due in part to compaction of the soil surface with heavy equipment, creation of large relatively unvegetated watersheds, and elimination of natural dendritic ephemeral drainage patterns. Methods for stabilizing gully channels which may develop prior to establishment of sufficient vegetation to control erosion are analyzed. Utilization of various sizes of riprap for channel lining, the use of riprap check dams, reinforcement of riprap check dams, and the relation- ship of type of control structure to area of watershed and resultant flow velocities are discussed.

Jan 1, 1986

By P. Somasundaran

Electrochemical properties of silicate minerals govern their behavior in processes such as flocculation and enhanced oil recovery that can occur at elevated temperatures. Knowledge of these properties as a function of temperature can be helpful in developing an under- standing of the role of these interfacial properties at non-ambient temperatures. Zeta potential of Sodium Kaolinite and quartz has been determined as a function of pH and temperature in this work. Both systems exhibited markedly different behavior at higher temperatures and also exhibited significant hysteresis. Results are examined in terms of possible dissolution of the minerals and surface reactions at different temperatures.

Jan 1, 1986

By G. T. Lineberry

Reduced clearance is one of the most important characteristics of encumbered space in underground coal mining. Another key variable is the maximum velocity at which a piece of mobile mining equipment can operate in this limited space. Typical velocity- clearance curves for different mine transportation systems are developed and characterized. Applications of the relationships are examined, emphasizing their significance in the design and control of mine materials handling systems.

Jan 1, 1983

By Y. C. Kim

The results from a retrospective study are described in this gaper in which she past development drilling activities were investigated using geostatistics. The purpose of the study was to determine the amount of savings in drilling cost that could have been realized through the optimal placement of sequential drill holes using geostatistics. Out of 144 DDH's that were in place within the study area, the results showed a possible elimination of 34 DDH's without any reduction on the confidence interval of the global reserve estimates. If the incremental savings from one drilling campaign to the next were considered, however, the amount of percentage savings were even greater. Other interesting results from this study were; 1) tangible demonstration of the importance of a proper geologic delineation within the study zone, and 2) the robustness of the obtained experimental variograms from the rather early stage in development drilling.

Jan 1, 1981

By Richard A. Brown

The direct precipitation of uranium with hydrogen peroxide has been known since 1877. Commercial use of the process began in the 1960's. During 1967 the Bureau of Mines assisted the Climax Uranium Co., Grand Junction, Colorado in the development of a uranyl peroxide precipitation process to control a molybdenum impurity problem (1). Atlas Minerals, Moab, Utah has used hydrogen peroxide to control vanadium and sodium levels in their uranium concentrates since 1969 (2). Recently, the use of hydrogen peroxide by the uranium industry has grown, particularly since the increased demand for uranium has led to the processing of low grade ores. Impurities present in low grade ores can be concentrated with the uranium during milling and will substantially complicate the refining of uranium yellowcake concentrates. Consequently, commercial nuclear fuel processors have imposed stringent specifications and penalties to control these impurities. The ability to produce a pure uranium yellowcake can eliminate penalty or reprocessing costs. Hydrogen peroxide precipitation of uranium is specific and quantitative, producing a very high purity product.

Jan 1, 1980

By A. L. Hauff

As US Coal producers are looking more and more to the international markets, they face the complex job of planning and managing transportation logistics which make effective use of production capabilities, considers the various contract requirements to be fulfilled, Train, Truck and Vessel capacities, port restraints, etc. Pulling all the necessary pieces of information together to allow proper planning throughout the supply chain is often a time consuming, manual but necessary task. This paper will discuss the various constraints, requirements and considerations to supplying coal to a global market.

Jan 1, 2012

By L. C. Bartel

Geologic features such as structure (faults, folds, fractures, etc.), water bearing zones, aquifers, pemeability variations, and porosity variations are important for mine planning and in situ energy recovery processes. Features important for planning a mine will be important for planning the recovery of energy by in situ processes. Various geophysical techniques might be used to obtain the necessary geologic information. In this paper, case histories will be discussed of the use of electromagnetic geophysical surveys at a potential underground coal gasification site and a potential tar sand oil recovery site to obtain pertinent geologic information. Results show that the controlled source audio- frequency magnetotelluric technique shows promise for mapping faults and natural fracture systems when there is a sufficient resistivity contrast.

Jan 1, 1982

By A. J. Sinclair

One hundred and eleven pyrite samples from 3 porphyry-type deposits in the Canadian cordillera were analyzed (many in duplicate) by AA spectrophotometry for Co, Ni, Cu, Pb, Zn and Mn. All elements have density distributions that are lognormal or combinations of lognormal populations. Co and Ni in pyrites show zonal patterns that relate generally to mineralogical zones in the porphyry systems, particularly if contoured as the Co/Ni ratio. High Cu values in pyrites also correlate with Cu-rich mineralogical zones. Other elements studied appear less regular in their distribution patterns, although Zn highs in pyrite seem to occur sporadically near the margins of porphyry systems. In particular cases, pyrite geochemistry shows potential as an exploration tool to aid in target definition for detailed exploration.

Jan 1, 1976

By Donald I. Bleiwas

The U.S. Bureau of nines evaluated the potential availability of tungsten from 57 tungsten mines and deposits in 19 market economy countries (1). The 38 properties that were producing at the time this study was performed contain approximately 375,000 tons1 of W03 (tungsten trioxide). The total estimated recoverable resource from all properties studied, both producers and nonproducers, was 1.2 million tons W03 (demonstrated level). Approximately 143,000 tons of W03 is recoverable from producing properties with costs at or below the January 1983 market prices. The study indicates that by 1990 production from currently operating mines in market economy countries will decrease as their demonstrated resources become exhausted. Some of this potential decline may be offset by lower than anticipated levels of market demand, discoveries of additional resources at producing mines, development of other known deposits, and/or discoveries of new deposits. Development of new tungsten resources in market economy countries will likely result in costs higher than exist at currently producing properties. The People's Republic of China has been steadily increasing production and export of tungsten in various form and currently supplies about 25 pct of U.S. imports. China's tungsten mines are large, high-grade operations capable of producing at relatively low cost. These factors, coupled with China's apparent need for foreign exchange, could lead to further expansions of production and exports from China, with a consequent increased dependence by market economy countries on China for tungsten requirements and a threat to the survival of the market economy countries' tungsten industries.

Jan 1, 1984

By Romeo S. Jurani

Bulkspray cooling has been economically applied in cooling the hot environment of South African gold mines for the past two decades. Its success in that country led to its introduction at Gulf Mineral Resources Co.'s Mt. Taylor Mine in 1981 when increased drifting imposed additional cooling requirements. The bulkspray cooler developed and used at Mt. Taylor has a heat transfer capability of about 500 to 1500 kW. It is compact and portable, designed to be moved as required to maintain working temperatures in the advancing drift faces.

Jan 1, 1983

By Brij M. Moudgil

Flotation of fine and coarse coal after multistage addition of the frother was found to yield coal fractions with significantly lower ash content as compared to the feed. It was observed that the lowest ash content, specific gravity and reactivity of coal was associated with finer size fractions. Ignition and combustion characteristics of different coal fractions were evaluated using a differential thermal analyzer (DTA) with calorimeter attachment. It is suggested that in the ignition stage, the removal of mineral matter affects the reactivity through the physical changes brought about by the ash removal. In the char combustion stage the mineral matter seems to influence the reactivity through the catalytic activity of surface concentrations of metal ions, ratio of combustible/incombustible material, internal pore structure and roughness.

Jan 1, 1984

By Paul Kents

The Canadian Javelin Limited Cerro Colorado copper-porphyry deposit in Panama, possibly the largest known copper-porphyry, contains between 1350 and 450 meter elevations, drill proven and probable ore in excess of 3.0 billion tons averaging 0.65% of copper equivalent. The deposit is located in the Central Cordillera Range, straddling the Continental Divide at 1500 meter elevation. Local topography is very steep. Accessibility is difficult, all logistics made by helicopter, and only recently a 52 km. road from the Pan-American highway was completed into the area. The deposit was discovered in 1969, and since then 75 shallow exploratory holes and 98 deep holes, the deepest 1340 meters, totalling 45,000 meters have been drilled. Deep holes were drilled at the corners of a regular rectangular 150 meter grid.

Jan 1, 1975

By C. E. Capes

The spherical agglomeration process provides an attractive method for the cleaning and recovery of fine coals in the form of compact oil-bonded pellets. In treating a washery effluent containing 50% minus 20 micron material by this technique, the slurry was first mixed under vigorous agitation with oil to deash and dewater the fine coal. The flocculated coal pulp was then formed into larger agglomerates on a modified balling disc. The operation of a semi-pilot scale process is described and an analysis of some of the operating and system variables is given. A semi-theoretical expression to predict the final agglomerate size under various conditions is derived and compared with the experimental data. Coal producers are faced with a growing requirement to clean and recover fine mesh coals. Greater mechanization of the extractive and preparation processes has resulted in finer-sized products containing larger quantities of associated foreign matter and preparation plant effluents contain quantities of fine coals which are potentially valuable. These losses will probably increase with the expansion of production and will require the development of effective disposal and utilization processes under pressure of the lack of adequate disposal areas, the enforcement of air and stream pollution laws, and the economic need to obtain the maximum yield of salable product(1)

Jan 1, 1970

By James R. Evans

Forecasting demand is an art as well as a science, and much personal judgment is required. National forecasts made for sand and gravel, crushed stone, and/or aggregate may be misleading or unhelpful locally. This is because of significant variation in demand within different geographic and/or political areas in the United States, and/or the use of an inadequate data base and forecasting methodology. The best forecasts may be made for local or regional market areas, irrespective of geographic or political boundaries, provided a proper data base is available. The Bureau of Mines compiles detailed statistics on commodities sold or used in the construction industries and, therefore, is in an advantageous position to make national aggregate demand forecasts.

Jan 1, 1978