Search Documents

By James A. Commins

Accurate engineering predictions of energy needs for pollution control equipment used in surface mining operations is critically important to sound management selection of control alternatives. This paper will describe a procedure for evaluating two control alternatives with different energy needs. Three steps are involved: an analysis of the pertinent regulations, a determination of the size distribution of the particles being emitted, a calculation of the energy needs and costs of the candidate control systems as a function of these regulations and emission characteristics. The principal air pollutant to be controlled in surface mining operations is particulates, or dust, some of which is already on the material introduced into the primary crusher and other dust which is generated by the various steps in the subsequent processes. The requirement for control stems both from regulations concerning workers at the operating site, and the community surrounding the operations. In order to speak quantitatively about the need for control we will use regulations that pertain in Pennsylvania although it must be borne in mind that such regulations vary according to juristiction.

Jan 1, 1975

By Ronald D. Hill

The occurrence of acid mine Drainage (AMD) with coal mining has been well documented. (1) Less documentation is available of its association with other types of mining, e.g., copper, gold, zinc, and sulfur. Yet there are many locations in the western states where acid mine drainage is as great a pollution problem as in Appalachia and in some cases, because of the high copper, zinc, and arsenic concentrations, they present an even more difficult problem. Until a few years ago, it was generally believed that the neutralization of acid mine drainage was uneconomical thus, AMD was allowed to discharge freely into our streams. However, the demand for good water finally dictated that the mining industry be included under pollution laws. In 1964 the Commonwealth of Pennsylvania passed a law requiring that all active mine discharges meet a discharge standard of pH 6-9, iron less than 7 mg/1, and the water must have a net alkalinity. Several other states now require active mines to treat AMD. In all but a few cases, lime neutralization, often in conjunction with aeration, has been the treatment method used. The high cost of lime as compared to limestone and the poor quality sludge, (slow settling, large volumes, and low solids content) has stimulated work in the utilization of limestone. This paper reports on the current state-of-the-art of limestone treatment of AMD.

Jan 1, 1970

By R. J. Mirville

Flocculation is an important step in the treatment of coal preparation waste waters. The effects of polymer charge and molecular weight and solution pH and ionic strength on the adsorption and flocculation characteristics of a series of polymeric flocculants on some typical waste water constituents have been studied experimentally. The results indicate that the nature and extent of flocculation are strongly system-dependent. For the case of coal, both adsorption and flocculation behavior can be correlated with the polymer conformation in solution. For the mineral constituents, on the other hand, adsorption and flocculation depend also on the surface properties of the solid.

Jan 1, 1979

By Edmond F. Lawrence

The Calico area lies within the Walker Lane fault zone, six miles north of Schurz, Nevada. The mineralized area is overlain by a thick section of Tertiary tuffs and ash-flows, that have been intruded by a series of andesite plug, dikes, and sills. The pre-Tertiary rocks outcrops only in two areas at one to two miles distance from the drilling areas. Underlying the volcanics are sediments ranging from siltstones, sandstone, calcareous shales, to carbonates of the Luning sequence. These have been intruded by one or more phaneritic intrusives ranging in composition from quartz diorite to quartz monzonite, with the development of a skarn zone on the south flank that contains extensive mineralization consisting of magnetite, pyrrhotite, pyrite, and chalcopytite, with traces of sphalerite, galena, and molybdenite. The magnetite, pyrrhotite, and part of the pyrite appears to be contemporaneous with the skarn, while, part of the chalcopyrite, galena, sphalerite, molybdenite, quartz, and calcite, occurs as minute veinlets cutting the other minerals. This later mineralization may be associated with a late stage of the same sequence, or possibly associated with another intrusive to the southwest. Geophysical work has consisted of aerial magnetics, ground magnetics, gravity, seismic, and induced polarization surveys. Preliminary induced polarization surveys indicated anomalies at depth, both over the magnetic anomaly and to the northwest. Subsequent IP work confirmed this earlier anomaly, and drilling disclosed extensive mineralization at depths of 400 feet on the northwest end and over 1,000 feet to the southeast.

Jan 1, 1967

By L. Frost

The establishment of a retreat system of longwall mining in this submarine coal field has been under study for many years and, although in special cases there have been limited local applications of this method of mining, there has been no attempt until quite recently to establish a uniform system of longwall retreating' in this area (see Figure 1) Where retreat walls were established, it was strictly as a result of physical, rather than economic conditions. In some of the operations- of the Corporation, where the coal was liable to spontaneous combustion- or the area subject to bumps as in No. 2 Mine of the Cumberland Railway and Coal Company in Springhills the recovery of the coal on a retreat system was more or less a necessity.

Jan 1, 1964

By R. J. Caine

Like most major firms engaged in project management, Dravo Corporation faces a constant challenge to keep its management systems in tune with the ever-increasing demands imposed by larger and more complex projects. This paper suggests that one of the key elements in meeting this challenge is more effective organization of project data. It reveals some of the details of a program at Dravo's Minerals 6 Metals Division which seeks, through better organization of project data, to improve Dravo's capabilities in estimating, cost control, scheduling, performance reporting and material control. In particular, this paper discusses ideas Dravo is developing for improved job numbering, codes of accounts, requisition and purchase order numbering, inventory cataloging, and employee/badge numbering.

Jan 1, 1980

By J. E. Moyle

Rio Algom Corporation of Wilmington, Delaware is a wholly owned subsidiary of Atlas Alloys Inc., an Ohio Corporation, which in turn is 100% owned by Rio Algom Mines Limited of Toronto, Canada. Rio Algom is controlled by the Rio Tinto Zinc Corporation of London, England, which has subsidiaries and affiliated operations throughout the world. Rio Algom geologists first became interested in this Utah pro- perty in 1966, after preliminary drilling had indicated that a known orebody close to the surface appeared to continue on the dorm thrust side of a major local fault, known as the Lisbon fault. Accordingly, in 1968, arrangements were made to acquire what was known as the "Humeca Option", a total of 2,573 acres located in San Juan county in south-east Utah, 35 miles south-east of the town of Moab.

Jan 1, 1975

By Manuel Viveros J.

This paper will deal with the type of rocks so called evaporites, which are sedimentary rocks produced by water evaporation from seas, lakes or marginal lagoons, in warm and arid climates. Salts derived from these deposits are precipitated according to their solubility; that is, the more soluble precipitates first, overlain by other sediments like silts, shales, limestones, sands, etc. The most common evaporites, according to their chemical composition, are : Chlorides Sulphates Carbonates Nitrates Borates Common salt, or halite, sulphates like anhydrite and gypsum, are the most important. Potassium chloride (silvite and carnalite) and potassium sulphate are of great commercial value.

Jan 1, 1974

By Dennis C. Parker

The Porters Creek clay is mined for its absorbent properties. The formation is part of the Upper Mississippi embayment and is recognized in Alabama, Mississippi, Tennessee, Kentucky, Illinois, and southeast Missouri. Major minerals in order of abundance are Montmorillonite, Quartz, Illite, Kaolinite, and Chlorite. Mining consists of open pit operation utilizing track loaders or scraper. The clay is dried or hardened in rotary kilns and crushed to size by roll crushers. The clay granules are sized and air classified prior to storage for shipment or packaging. Granules are sold for pet absorbents, oil absorbents, anti-skid material, fertilizer, and pesticide carriers.

Jan 1, 1979

By Makoto Terada

The most important consideration in planning the plugging and sealing of a mine for mine water control is to predict the water flow from the mine. For this purpose, a method of numerical analysis on the water behavior in the ground at the concerned mine area was developed and the mine water flows were simulated. A hydrological survey at the surface of the mine determined the recharge rate of ground- water and the apparent permeability of ground.

Jan 1, 1982

By E. L. Michaels

Laboratory and pilot scale tests have been made to deter- mine the utility of heavy media separation, particularly a cone type separator, as a means of recovering aluminum from shredded municipal solid waste. The effect of the method of shredding on the behavior of aluminum in a heavy media system was deter- mined. Two-stage pilot scale heavy media separations were made with size fractions of shredded refuse. Recoveries of aluminum, as well as other components of the refuse, were measured and medium losses were determined. The experimental results indicate that with certain reservations a heavy media cone system can be utilized for aluminum separation and recovery from shredded and air classified municipal solid waste. Observations made using two-stage heavy media separation in a drum unit are included. Qualitatively, the results from the two types of separators are similar.

Jan 1, 1974

By J. G. Davis

Continental Oil Company has spent over four years of research on the fundamentals of potash solution mining. This work included laboratory investigations of salt solution, brine flow, selective extraction of KC1 from sylvinite, and control of cavity geometry. Laboratory results were expanded by means of a series of field tests, and subjects such as well completion and hydraulic fracturing were added to the investigation. Both single-well and multi-well mining systems were studied in the field work. The current paper discusses one field test in which potash was solution mined from a thin sylvinite ore zone in the Carlsbad Potash Basin. A two-well mining system was used for this test. The potential economic value of solution mining has been recognized for many years, and applicable United States patents date back into the past century. Principal advantages of the process over conventional mining include (1) the use of drilled holes and solution techniques in- stead of excavated shafts and caverns and (2) the ability to mine both land and marine deposits through any type of overburden geology and below conventional mining depths.

Jan 1, 1969

By William M. Kester

Finely sized Upper Freeport coals are beneficiated to reduce ash and sulfur using high-intensity magnetic separation to process both (1) raw, untreated coal as well as (2) raw coal which was pre-treated thermally with steam and air. Substantial, sulfur and ash reduction can be obtained using both approaches to magnetic beneficiation of coal fines, but evidence indicates that pre-treatment which would constitute a costly supplementary step is technically inferior to the direct beneficiation of raw, untreated coal. These bench-scale studies demonstrate that if high-intensity,; high capacity, dry, magnetic beneficiation equipment can be developed and' installed at coal burning power plants or at appropriate points in coal preparation plants substantial quantities of sulfur may be removable from coal after pulverization as a means' to reduce air pollution.

Jan 1, 1965

By G. C. Hambleton

There is sufficient indication of the existence of a basic misconception in the Coal Mining industry (on a world-wide basis) as to what computer control really does, what it costs, how it works and how and what it achieves as to make this presentation a welcome opportunity to present the case in what we hope is a simple, meaningful way. A plant cannot be said to be "automated" unless the control system has the capability to react automatically in accordance with predetermined programs under a great multiplicity of operational situations.

Jan 1, 1981

By James N. L. Lukanuski

Three porphyry copper districts in southern Arizona are partly overlain by post-ore fanglomerates which share certain physical and petrologic characteris¬tics and which may comprise a distinct and significant class of rock. These units are the Locomotive fanglomerate of Ajo, the Helmet fanglomerate of Twin Buttes-Mission-Pima, and the Cloudburst formation of San Manuel-Kalamazoo, termed "Locomotive-type fanglomerates" herein. Post-ore units at Poston Butte and Lakeshore, Arizona, and Sar Chesmeh, Iran, also appear to fit this class. "Locomotive-type fanglomerates" are composed of poorly sorted conglomerates, lenticular sandstone beds, andesitic to rhyolitic flows and tuffs, and unique monothologic landslide breccias. They contain fragments of holyokeite - - a rare oligoclase lava of porcellaneous appearance. Their basal contacts are considered to be depositional and overlapping, sometimes complicated by later low-angle faulting. They arc quite different than the younger Cila, Pantano, and most "Whitetail" alluvial beds, and the older Amole, Recreation, Claflin Ranch, etc. elastics; in particular they are thinner and less widespread. Their ages are Eocene to late Oligocene. "Locomotive-type fanglomerates" may be genetically related to porphyry coppers as products of subsequent differentiation and volcanism, and sedimentation in short-lived basins of restricted area and extreme relief. They might be utilized as reconnaissance guides to target areas and as structural guides within target areas in the southwestern U.S., Northern Mexico, and elsewhere.

Jan 1, 1975

By A. T. Yu

The quest for ore in an open pit is fundamentally an earth moving proposition. This thesis is vividly underscored by the rapidly increasing volume of waste to be removed in newer mines, where in some instances waste to ore ratios have reached as high as 20 to 1. Continuing depletion of high grade reserves, greater demand for raw materials, coupled with ever climbing labor costs, have made the problem still more pronounced and the need for more effective means of earth moving in an open pit even more acute. A conservative approach to the problem has been to upgrade the sizes of conventional earth moving equipment such as shovels and trucks. In many open pits, particularly in the C.S., this has been responsible for the generally down- ward trend of earth moving costs. None the less, the investment costs of these machines are high, and their gigantic engines are seldom fully utilized. Moreover, a large number of operators are required and maintenance remains relatively high. Unfortunately most people have felt that no other viable alternative was in sight within today's technological capabilities.

Jan 1, 1973

By Charles LeMoyne

The Cable belt Company has been building single flight conveyors for a number of years. The simple design concepts of this type conveyor, introduced over thirty years ago, when distances of one to two miles were considered major advances in technology, remain relatively unchanged. Conveyors that are 6 to 20 miles (9.0 to 32 kilometers) long are being built and are presently in operation through- out the free world. The Cable Belt conveyor is not conventional in its construction. Cable welt differs from conventional troughed idler conveyors in that the driving medium and carrying medium are separated. Motion is provided by two endless steel cables running the length of the conveyor. The cables are driven by a single drive unit incorporating a differential gear which insures identical cable linear speeds and equal tension in both cables at all times. The belting is located and supported by "V" shaped shoeforms moulded to the belt which form a wedging action. The friction between the belting and rope is sufficient to prevent slippage (See figure 01).

Jan 1, 1983

By Philip A. Bucci

The Florida phosphate industry successfully uses froth flotation to concentrate phosphate in: the particle size range of approximately 28 to 150 mesh. However, as recently as 1965, coarse particles in the range of 14 to 28 mesh generally had not been beneficiated by conventional flotation methods at recoveries high enough to be considered adequate. It has been customary to upgrade this coarse material; by "agglomerate flotation" or "skin flotation" using belts, tables or spirals. While these devices have proved commercially effective, their capacities are much lower than those of froth flotation cells. To determine whether coarse phosphate material could be recovered successfully by froth flotation, Armour Agricultural Chemical Company began a series of pilot and plant tests; in April 1965. Objective of the tests was to compare over-all performance of a froth flotation cell design relatively new to the phosphate industry with results from the belt circuit at the Bartow, Fla., plant.

Jan 1, 1966

By J. R. Nawrot

Reclamation of potentially acid producing coal processing waste requires a 4-foot cover, and/or treatment to allow vegetation establishment. If not planned properly, soil covering alone does not prevent refuse acidification or formation of acid seeps. Adequate neutralization enhancement prior to soil covering can maintain an alkaline environment in the soil refuse interface and prevent acidification. Direct vegetation establishment using only limestone amendment (without soil cover) can successfully reclaim aged and weathered fine (Blurry) and coarse (gob) refuse if adequate neutralization treatment is provided for the oxidized surface zone. Acid seeps, representing an "after-the-fact" verification of an imbalance of acid-base equilibrium may also be corrected using upslope alkaline recharge techniques. Concentrated alkaline recharge pools have been constructed above previously soil covered acid gob at the Peabody Will Scarlet Mine to abate acid seeps. Preliminary monitoring results (1989-1992) from a concentrated alkaline recharge pool demonstration project in the Pit 4 area of the Will Scarlet Mine have documented a 50 to 80 percent reduction in acidity in the principal recharge pool groundwater zone. A 22% reduction in acidity has occurred in the primary seeps located downslope from the alkaline recharge pools. The initial improvements in water quality are seen as a positive indication that groundwater acidity will decrease further and amelioration of the acid seep will continue.

Jan 1, 1993

By Margaret Fuller Boos

Precambrian granitic pegmatites on the west, south west, south and southeast slopes of Storm Mountain, Larimer County, northern Colorado, were explored and mapped geologically 1956-1959. The area between Crystal Mountain Mining District on the north and Hyatt pegmatite mine area on the south was nearly inaccessible until a company built an access road, which was completed in 1959, into Roosevelt National Forest and its jeep-type roads. The area is extremely rugged, rising from some 6,000 feet on the highway at Drake, on Big Thompson River, to an altitude of over 10,000 feet at the summit ridge of Storm Mountain. Almost innumerable pegmatites of every possible type of granitic pegmatite intrusion infest the Precambrian gneisses and schists of the southwest-tilted fault block of Storm Mountain. The major bodies stand at least 100 to 200, feet high above the surrounding forest floor. Core drilling has shown that some extend to at least 200 feet below the surface. They blunt out at the southwest, some keel out below and others are faulted out at their southwest ends. Strike length ranges from 200 to 600 feet. The massive bulky bodies have nearly vertical walls. Contents are zoned or ribboned and layered. They consist of local commercial bodies of beryl, potash feldspar, mica, uranium minerals and quartz. As yet no lithium minerals have been encountered.

Jan 1, 1960