Search Documents

By J. A. Rusnak, K. M. Mohamed, M. A. Van Dyke, M. M. Sears, G. Rashed

"Researchers from the National Institute for Occupational Safety and Health (NIOSH) recently developed a coal-mass model to realistically simulate the deformation and loading behaviors of the ribs of coal pillars in underground coal mines. The scale-dependent properties (stiffness and strength) of coal material were considered in the coal-mass model. In this paper the orientation of face cleat with respect to driving direction was integrated in the coal-mass model. The controlling parameters (dimensionless coal-mass scale and fracture strains) of the modified coal-mass model were calibrated using a published case study of coal pillar strength. Numerical models with wide ranges of controlling parameters were conducted to simulate the test pillar. The best match between the numerical modeling results and the measured stresses and deformations was achieved by using a coal-mass scale of 30 and fracture plastic shear and tensile strains of 3.25% and 0.325 %, respectively. INTRODUCTION The failure of coal pillar ribs by itself are a major hazard in underground coal mines. Furthermore, failing ribs can indirectly contribute to roof and floor instability by increasing opening widths across intersections and entryways. Over the past decade, rib failures have resulted in 12 fatalities, representing 28% of the ground-fall fatalities in U.S. underground coal mines. Mining depth has always played a very important role in assessing rib stability. Gauna and Mark (2010) completed an analysis of rib fatalities that occurred between 1996 and 2010. One of their most prominent and influential findings was the identification of a relationship among fatalities, depth, and mining height. Therefore, Coal rib stability will continue to be a challenge for future deeper mines in U.S. coal basins. In the past several decades, research efforts have focused on roof support. The current rib control practice in U.S. coal mines is to select rib bolts through a trial-and-error approach (Mohamed et al., 2015a). Rib failure incidents can be can be substantially reduced or even eliminated by adopting an engineering-based coal rib design approach. The factors affecting rib stability in coal mines are numerous and mutually dependent. These factors include but not limited to mining height and overburden depth, interburden thickness for multiple-seam mining, coal strength, cleat density, entry direction with respect to cleat orientation, existence or absence of partings in the coal, percentage of extracted roof and/or floor rock, density of rib bolt support (Mohamed et al., 2015a). Moreover, it is difficult to isolate the particular effect of a specific factor on the overall rib stability. Therefore, a reliable empirical rib design approach is not achievable because it requires a significant number of case histories to be collected in order to have a reasonable range of all of the critical parameters. However, numerical modeling can be a practical tool to assist with rib support design if the modeling is realistic, which can only be achieved through calibration and validation of the numerical model against field data."

Jan 1, 2018

By J. Helton, J. L. Bellanca, M. McNinch, L. R. Swanson

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the official position of the National Institute for Occupational Safety and Health, Centers for Disease Control and Prevention. Mention of company names or products does not constitute endorsement by NIOSH. ABSTRACT Accident data indicates that mobile haulage poses a significant pinning, crushing, and striking risk. Proximity detection systems (PDSs) have the potential to protect mineworkers from these risks. However, unintended consequences of mobile PDSs can undermine the safety benefit they provide. Soliciting iterative user input can improve the design process. Users help provide a critical understanding of how mobile PDSs may hinder normal operation and endanger mineworkers. Researchers explored users’ perspectives by conducting interviews with mineworkers from seven mines that have installed mobile PDSs on some of their haulage equipment. Mineworkers reported that mobile PDSs affect loading, tramming, section setup, maintenance, and general work on the section. Mineworkers discussed the operational effects and increased burden, exposure, and risk. Mineworkers also suggested that improved task compatibility, training, logistics, and PDS performance might help address some of these identified issues. This paper also gives additional insights into mobile PDS design and implementation. INTRODUCTION Pinning, crushing, and striking accidents are a large problem in underground coal mines, especially for mobile haulage. Between 1984 and 2014 there were 179 non-fatal and 42 fatal pinning, crushing, and striking accidents involving mobile haulage vehicles, including coal hauling machines and scoops [1]. Proximity detection systems (PDSs)—automated systems that decelerate and stop a vehicle in order to prevent a collision—have the potential to protect mineworkers in these situations. In fact, PDSs are now required on all place change continuous mining machines as of March 16, 2018, as a result of the final rule published in January 2015 (30 CFR 75.1732) [2]. To address mobile haulage, later in 2015 the Mine Safety and Health Administration (MSHA) also proposed a new rule that would require PDSs on mobile haulage vehicles [3]. Though there has been no additional actions related to the proposed rule and it is not currently required, mobile PDS can still help to save lives. MSHA estimates that the adoption of mobile PDSs could prevent approximately 70 injuries and 15 fatalities over the next 10 years [4]. As of June 2015, the underground coal industry had already equipped 155 of the 2,116 mobile haulage vehicles in use [1]. In order to capitalize on the projected safety gains afforded by PDSs, it is important that the systems are designed and implemented effectively. Along with others, researchers at the National Institute for Occupational Safety and Health (NIOSH) have been exploring PDSs for more than two decades [5-7]. Throughout this time, NIOSH has also held several stakeholder meetings (2010, 2014, 2016, and 2017) in order to disseminate information and provide an opportunity to discuss on ongoing issues and concerns. Despite some progress, human factors remain a key concern. Previous research examined mineworkers’ attitudes towards PDSs on continuous mining machines [8] as well as how continuous miner operators’ perceptions of risk have changed as a result of PDSs [7]. However, stakeholders have still expressed a need to better understand how mobile PDSs affect the mining process, the mineworker, and whether and how they may present previously unidentified risks.

Jan 1, 2019

By L. B. Kirk, A. R. Kirk

At New World, Au-Cu-Ag mineralization occurs in stratiform car-bonate-hosted, massive sulfide-iron oxide, and skarn-replacement deposits. Regional pyritic-alteration, local massive sulfide mineralization and mine wastes generate acid drainage within the district. Water quality improves down gradient through dilution and mixing of acid and metal-rich mine water with bicarbonate-rich, low-metal surface and groundwater, and precipitation of metal-rich ferrihydroxide phases. Natural deposits of ferricrete indicate that pre-mining ARD has occurred, providing important clues to pre-mining water quality. The geoenvironmental model identifies the Cu-skarn mineralization as the primary target for ARD management. Closure success will be limited by the geoenvironmental nature of the natural mineralization.

Jan 1, 2004

By Andrew Trusiak

Brunswick Mining, employing approximately 1600 employees, is located 40 km south of the city of Bathurst in north eastern New Brunswick. The mine has operated as two lead-zinc operations - the underground mine(No.12) and the open pit mine (No.6). The open pit orebody is presently being' mined by underground methods. It is expected that the No.12 mine will furnish the entire ore supply by the end of 1981. The flotation practice prior to 1971 has been described by Neumann and Schnarr(1) and by Erskine (2). More recently, the current flotation practice has been described by McTavish(3) and deals with some major circuit modifications between 1972 and 1978. The period 1978 to 1980 has seen the completion of. a major flotation cell replacement and expansion program for the No.6 concentrator, and the implementation of computer control in the No. 12 CuPb and Zn flotation circuits.

Jan 1, 1981

By F. A. Renninger

The mineral aggregate industry is the world's largest mining and processing endeavor, yet it is graced with little of the romance or public awareness that accompanies mention of gold, silver, iron, copper, uranium, or aluminum mining efforts. Much of this reaction is undoubtedly due to the fact that the uses to which crushed stone and sand and gravel are normally put are not fully recognized or appreciated by the general public. Few individuals ever have occasion to purchase mineral aggregates for anything other than use for decorative shrubbery beds or walkways. They may, however, buy ready-mix concrete for a new patio, bituminous concrete for a new driveway, concrete blocks, or other building materials for a new room and never realize that the primary ingredients of their purchases are either direct or indirect products of the mineral aggregate industry. The average person driving past an operating crushed stone quarry or an active sand and gravel pit rarely realizes the economic impact the industry, represented by that operation, exercises on the general economy. He is not aware, nor does he really care, that elements of the modern comfortable environment to which he has grown accustomed rely to a great extent on the products of the crushed stone and sand and gravel industries Iron and steel, glass, cement, agriculture, and highway and building construction are but a few of the major industries to whom the products of the mineral aggregate industry are basic. Without these industries or without the stone, sand, and gravel basic to them, most of the major elements of our modern day civilization would be non-existent.

Jan 1, 1968

By M. L. Wouden

The Bureau of Mines investigated pegmatite and granite formations at Copper Mountain, Fremont County, Wyoming, for recovery of tantalum and niobium. Sampling of surface exposures identified about 1.27 mega tonne of pegmatite resource material ranging between 0.02 and 0.04% Ta20, and 0.007% Hb20,. Beneficiation studies were conducted involving coarse-grained and fine grained pegmatite samples. Over 80% recovery of the coarse-grained tantalite was achieved in a concentrate averaging over 45% combined tantalum-niobium oxide. Lower concentrate grades and recoveries resulted from the treatment of fine-grained pegmatite.

Jan 1, 1991

By Billy W. Parks

This paper reports on the first 2 years in operation of a special-purpose coal handling rig which provides blending, temperature reduction, and continuous, automatic mechanical sampling as part of midstream barge to ship coal transfers. Briefly reviewing some of the characteristics of coal handling peculiar to midstream transfers, the paper discusses how the most beneficial aspects of midstreaming were enhanced through the design of this blending and sampling rig.

Jan 1, 1986

By M. Misra

A sample of thorium-contaminated soil from Kirtland Air Force Base (AFB) was subjected to froth flotation for removing thorium contaminants. A series of flotation tests were conducted to screen and evaluate the reagents. Among the collectors used, sodium oleate exhibited to show the promising results. Preliminary tests showed that a concentrate having activity as high as 5300 pCi/g can be obtained from the contaminated feed soil having activity 800 pCi/g. The volume reduction obtained was 89% and the activity recovery in the concentrate was 68%. The paper discusses the physico-chemical characterization data and the potential physical separation decontamination schemes for the thorium contaminated soils.

Jan 1, 1996

By D. P. Bryan

The identification and-develop¬ment of new construction aggregate resources, the most common mineral mined, is an essential need in this country's growing urban areas. In developing an aggregate exploration program, a thorough geological identification of all potential aggregate resources in an area is still of primary importance but other factors have also to be considered. These include physical properties, end product application, transportation and mining costs, and local government regulations including zoning. The present major aggregate producers are most likely to develop these future resources and are in the best position to initiate comprehensive exploration programs.

Jan 1, 1987

By M. C. Roberts

In assessing the future markets for a mineral from a producing district, three key aspects must be considered: 1) the future growth in markets, 2) the competitiveness of the district in terms of production costs and reserve adequacy, and 3) the competition from alternative sources of supply. This paper will focus on the first issue by developing a method of predicting the demand for phosphate from the trends in the major markets for phosphate products, primarily the fertilizer and agricultural markets. The paper will show how broad changes in the final end use markets for phosphate products have evolved over time and how this has affected the needs for phosphate rock. These trends are then projected into the future to make an assessment of future phosphate requirements.

Jan 1, 1998

By D. S. Kimbal

The McCoy/Cove mine is located 48 km (30 miles) south of Battle Mountain, Nevada, USA, in the Fish Creek Mountains at an elevation of 1548 m (5080 ft), see Figure 1. Joseph H. McCoy first discovered gold at this location in 1914. This discovery led to the Gold Dome Mine which produced the first gold from this area in 1928. After the Gold Dome era, the land remained relatively dormant until Houston oil and Minerals Corporation purchased the claims from the Summa corporation and defined an ore body at the present day McCoy pit. In 1986 Tenneco Minerals (formerly Houston oil and Minerals corporation), sold the McCoy mine and adjoining claims to Echo Bay Minerals corporation. The Cove ore body was discovered soon after the sale to Echo Bay. Echo Bay expanded the heap leach operation and built the present mill which began processing ore in the fall of 1989.

Jan 1, 1993

By A. M. Raichur

The selective adhesion of hydrophobic Mycobacterium phlei to coal particles is responsible for flocculation of fine coal from associated ash forming minerals. The driving force for the differential adhesion is the hydrophobic interactions between the fatty acid surface of the organism and hydrophobic nature of coal. The effect of Mycobacterium phlei on surface hydrophobicity, surface charge and mechanism of adhesion on coal and associated minerals are controlled by several factors including hydrophobicity and surface and solution chemistry of the system. Adhesion measurements indicate that maximum adhesion occurs below the isoelectric point (IEP) of the coal particles. While massive adhesion of Mycobacterium phlei is observed on coal, however, negligible amount of Mycobacterium phlei attaches to mineral pyrite and quartz.

Jan 1, 1995

By R. H. Derammelaere

With renewed interest in coal slurry pipelines in China, Indonesia, Australia and Canada for electric generation, it appears worthwhile to update the relative economics of transporting coal by slurry pipeline. Three slurry pipeline technologies are evaluated for the commercial transportation of 3.0, 6.0, and 9.0 million tonnes per year (MMT A) example cases, over distances of 250 km, 500 km and 1000 km.

Jan 1, 1998

By N. Edmonson

The demand for sulfur divides into two major categories: agricultural and industrial. Most of the agricultural demand is related to the production of phosphate fertilizer products. Industrial demand is derived from the demands for a large number of products and is related to a variety of industrial processes, no one of which characterizes it in a simple way.

Jan 1, 1994

By J. S. Chung

As part of ongoing deep-ocean mining research, hydraulic transport systems as well as status of deep-ocean mining systems are reviewed in the aspects of manganese nodules and crusts from 800-6,000-m depth. The emphasis of the investigation of hydraulic transport is placed on the shape effect of particles on the pressure gradients and flowrates. Series of tests are being conducted to study the lift characteristics of a 2-phase vertically upward hydraulic transport of 2 types of small solid particles in a PVC pipe of 1-in (2.54 cm) diameter: irregular-shaped silica sands and equivalent spherical glass beads. Pressure drops and mass as well as volumetric flow rates were measured by electromagnetic (EM) flowmeter and mass flowmeter. The particle sizes used are 8-10 mesh. The results in turbulent flow range of 104 < Re < 105 show that pressure gradients or friction factors are smaller for the spherical beads than the sands. The larger the concentration of the particles are, the larger the pressure gradients become. The larger the particle concentration is, the less the effect of particle shape on pressure gradients becomes. The shape effect is greater for the minimum particle transport velocities than for the settling velocities.

Jan 1, 1999

By P. F. Mataich

When the subject of plant computers is brought up most people visualize the computer&apos;s controlling the entire plant with very little operator intervention. Actually, this picture is true today in only a limited number of cases and will certainly not be true in the minerals industries for many years to come. There are several ways in which a plant computer can significantly contribute to improving plant operation and closed loop control is only one of these. First of all, what are the basic ingredients for good plant control? For good plant control, two requirements must be met. First, the operator must get good information feedback from the process and then he must know what action to take in response to this information. Control information can be obtained through instruments, laboratory analyses, or through simple visual observation. If it is timely and accurate and the operator knows how to use it, then we have the makings of a good plant control system. The computer can be of help in both these areas by getting good data back to the operator and in helping to develop a good control scheme for the plant.

Jan 1, 1966

By R. J. Hickson

The Grasberg copper-gold deposit was discovered in Spring 1988, just one year prior to the planned closure of Freeport Indonesia&apos;s original Ertsberg open pit copper mine. In spite of Grasberg&apos;s remote location, 600m above the Ertsberg, atop a hitherto inaccessible mountain, Freeport-McMoRan brought their latest open pit mine into production in the last week of 1989, less than two years after discovery. This paper describes the start-up of the operation, highlighting synergies drawn from both the original Ertsberg experiences and the current Freeport Indonesia underground mines.

Jan 1, 1991

By Dennis Z. Mraz, Maurice B. Dusseault

INTRODUCTION In 1982 and 1983, as part of the mine design program for a New Brunswick potash mine, series of laboratory tests were conducted on potash and salt samples obtained during the mine exploration program. Concurrently, two rock mechanics monitoring programs were initiated in-situ the short term test at site A, and the long term test at site B (figures 1 and 2). SHORT TERM TEST (FIGURE 1) The purpose of this test was to obtain a quick confirmation of laboratory data and comparison of the rock response to excavation with the data available from Saskatchewan potash mines. Instrumentation in the main drift was installed on Day 4 after excavation, and the pressure cells were pressurized on Day 33. The packer type cells in the east crosscut were pressurized on Day 25. Excavation of the west cross-cut was begun on Day 71. This "mine by" test has provided important information required for calibration of laboratory tests, as will be shown later. The test data recorded are shown in a series of diagrams: a. initial room closures, main drift-figure 3; b. convergence graphs, main drift-figure 4; c. stresses recorded, main drift-figures 5 to 8 and, d. stresses recorded, east crosscut - figure15 Three types of instruments were used in this test. In the main drift. Saskatchewan Research Council water type hydraulic inclusions. encapsulated in potash, were used to measure lateral and vertical stresses. In the east crosscut a home-made packer type hydraulic inclusion was used to record radial stresses. The convergence stations consisted of end-grouted bars of reinforcing steel. LONG TERM TEST (FIGURE 2) The purpose of the long term test was to study the steady-state behaviour of a single opening in potash. Site B was placed in a remote area of the mine, well away from any anticipated early mining activities. To assure homogeneity of rock mass, the site was placed within a 30 meter thick vertical limb of a syncline-shaped ore body contained within a 360 metre thick vertical section of salt rocks. It was excavated mechanically as close as possible to the designed square cross-section for the entire length of the room. The square cross- section was chosen in order to achieve a comparable geometry in vertical and horizontal directions; that is, to eliminate any undesired effects of geometry interaction with lithostratigraphy which might have generated non-homogeneous behaviour. The site was extensively instrumented. As in site A, the convergence stations consisted of end-grouted bars of reinforcing steel. However, in order to avoid any measurement inaccuracies which would be associated with the brittle yield zone in the opening walls, bars were placed to the same depth in opposite sides of the opening. This allowed the convergence measurement to be obtained as the absolute convergence between two points, rather than the convergence of a single point with respect to a potentially unstable reference. For stress measurements the Saskatchewan Research Council cells were placed vertically, laterally and radially. Unfortunately, due to cost considerations, it was decided to use a compacted sand, rather than grout, to encapsulate the cells in the boreholes. Due to the extremely small strain rates, only radial ly placed cells could be adequately pressurized. The rest of the cells did not perform adequately, and are currently being replaced.

Jan 1, 1986

By Z. Yu

The effect of particle size on coal dewatering has been well recognized However, there are no systematic studies on ultrafine coal dewatering. The results discussed last year revealed the effect of flocculant type and coal wettability on the filtration of ultrafine coal In this paper, the differences in dewatering between -25 µ m ultrafine and -500 µ m fine coal with addition of flocculants, surfactants and oil-emulsions in vacuum filtration are further investigated Significant differences were observed in the reduction of the cake moisture. The utilized emulsions were found to be very powerful and promising filtration aids for both ultrafine and fine fractions of hydrophobic and hydrophilic coal

Jan 1, 1995

By C. W. Baxter

Eveleth taconite company was formed in 1963 to mine and beneficiate taconite on the Mesabi range of Minnesota. Its thunderbird mine is located midway between the cities of Eveleth and Virginia, Minnesota, and the crude ore is transported by rail to its Fairlane plant approximately ten miles to the south of the mine, "figure 1". As is implied by the names of the mine and plant, the ford motor company is the principal owner of Eveleth taconite company, with an 85% interest, Oglebay Norton company holds the remaining 15% interest and also is the managing agent.

Jan 1, 1972