Search Documents

By Jr. Gambrell

For more cost effective strata control, a fundamental understanding of the behavior of the support system is needed. To assist in this understanding for shield supports, behavior of a four-leg shield design used on a soft floor in an operating longwall system is presented. The shield was constructed having a split base and a split caving shield. Attention is focused on other-than-normal loading on the canopy and its effect on deformation of the lemniscate links. Examples of the typical bending and twisting deformations are given. Schematics of the canopy, caving shield, and lemniscates showing important forces and moments are presented. Approximate minimum values of the forces and moments are calculated. The need for use of more inclusive three-dimensional design techniques is demonstrated.

Jan 1, 1990

By Robert O. Vernon

Urban sprawl, and all its attendant problems, is upon us. In Florida, and much of the rest of the world, this has been intensified by a special problem - the coastal zone - a land of high-intensity urbanization localized where the sea and our citizens interact. Florida is blessed by a long coastline of beautiful beaches, indented by estuaries, lagoons and spring fed rivers. Rocky and sand covered islands invite habitation. A large and varied fauna and flora make recreation an avocation and work a pleasure. Accompanying these people are all the sustaining, and satellite industries that find the climate, labor, and commodity markets, cheap water transportation, and natural resources to be attractive. It is estimated that by the year 2008 a megalopolis will stretch down the Atlantic Seaboard from Georgia to encompass the Keys and extend along the Gulf to Alabama. This city will be fenced by the sea on one side and by the water management works, necessary to provide the water supply for this complex, on the other. What can we do about increasing the amount of water available for this population and decreasing the resultant wastes??? Rarely has there been tendered a more favorable opportunity for a coordinated planning and development project that will provide public access to beaches and multiple use of the coastal lands. Florida, as a peninsula swept by ocean breezes, having a largely indigenous water supply and only the beginning of the pollution of estuarine and coastal waters can cope with air, water and coastal dissipation and pollution, if we have a beginning at providing a constant water supply and at limiting pollution. This answer would appear to lie underground, where the porous limestones are interbedded with impervious fine-grained sediments and ground-water that circulates through these aquifers empty to the ocean and Gulf along the continental slopes.

Jan 1, 1969

By W. J. Dolinar

The U.S. Bureau of Mines implemented the Fe2+ /Fe3+-SO2 anode reaction in a Cu electrowinning cell with full-size electrodes. Electrowinning was conducted using industrial electrolyte at 258 A/m2 (24 A/ft2) and 40 'C. Manifold injection of electrolyte provided circulation between the electrodes. Five-day operation using an optimized manifold gave an average cell voltage of 0.94 V at 89% current efficiency, which amounted to an energy savings of 2.82 MJ/kg (0.355 kW-hr/lb) compared to conventional electrowinning. Acid misting was completely eliminated, and SO2 concentration 23 cm (9 in.) above the cell averaged 0.06 ppm.

Jan 1, 1995

By Richard E. Gray

Virtually all structures show some signs of distress due to deterioration of the building components, to changed loads, or to changed support conditions. Changed support conditions result from ground movements. In mining regions many cases of structural distress are attributed to mining without considering alternative causes. This is particularly true of coal mining since it occurs under extensive areas. Coal mining is estimated to have already undermined more than eight million acres and may eventually undermine 40 million acres in the United States (HRB Singer, Inc., 1977). Other nonmetal and metal underground mines impact much smaller areas. Although it is sometimes difficult, even with careful study, to identify the actual cause of damage, persons responsible for underground coal mining should at least be aware of possible causes of building stress other than mine subsidence. This paper presents information on distress to structures and briefly reviews a number of causes of ground movements other than subsidence: Mass movements, dissolution, erosion, frost action, shrinking and swelling, yield into excavations and compressibility

Jan 1, 1986

By H. J. Bogert

Shallow, gently dipping quartz veins at the Mineral Hill Mine are mined in room and pillar stopes. Ore zones are severely folded and fractured, thus actual pillar strength and physical properties of the rock mass deviate significantly from conventional laboratory tests and pillar theory. Laboratory specimens large enough to include pre-existing fractures proved to be representative of actual pillar strength. Further adjustment for specific pillars was based on RQD. Deformation and stress were measured in several pillars during pillar recovery. Stress data and finite element modeling were used to estimate absolute pillar stress at failure. The stress/strain relation provided an excellent indicator of pillar behavior. Good agreement between lab data and underground data was found.

Jan 1, 1995

By C. J. Pritchard, R. D. Jacksha, K. V. Raj, C. Sunderman

"In underground metal/nonmetal mines, repeated short-term exposure to high levels of airborne contaminants can become a serious health issue. Currently there are no common mechanisms to control or mitigate these localized short-term high exposures to contaminants. To improve miners’ health and safety, the National Institute for Occupational Safety and Health (NIOSH) Spokane Mining Research Division (SMRD) is developing a Smart Monitoring and Control (SMAC) system for real-time monitoring of mine air quality, with integrated countermeasures to reduce these high concentrations of airborne contaminants in localized sections of mines. To develop and test a SMAC system that could be implemented in an underground mine, researchers at SMRD built a test apparatus incorporating a fan, louver, ducting, and sensors combined with atmospheric monitoring and control software. This system will institute effective countermeasures to reduce contaminant levels, improving miner safety and health. INTRODUCTION Underground metal/nonmetal mines continue to expand production by employing large equipment in greater numbers and by mining into hotter and more challenging environments which are typically further away from fresh air sources. This challenges the ventilation system to provide adequate quantities of fresh air to the workplace and increases the potential for air contamination that could result in immediate and long-term health and safety issues to miners. Currently, airflow and contaminant concentration in mines are typically based on full-shift sampling which may not identify repeated short-term exposures to high levels of airborne contaminants such as NO2, CO, diesel particulate matter (DPM), and dust with high silica contents. Repeated short-term exposure to these high levels of airborne contaminants over long periods can lead to serious health issues which are documented in several studies [1-3]. Based on data from ventilation surveys and contaminant measurements, mines often attempt to minimize exposures by sending more fresh air to the working areas where contaminant concentrations are found to be high. Real-time monitoring and control allows mines the option to monitor contaminants and implement controls in real-time. Real-time monitoring and control of the underground mine atmosphere has been a subject of research since its beginning in Finland at Outokumpu’s Pyhäsalmi Mine in 1969 [4]. More recently, the real-time monitoring and control problem has been addressed using ventilation on demand (VOD) systems [5, 6]. A VOD system attempts to deal with this issue on a global level by controlling fans, louvers, and doors to increase airflow to active work areas and reduce contamination. However, a VOD system only controls the distribution of airflow and may not be helpful in mines where the airflow is at maximum capacity. Researchers at SMRD are developing a SMAC system for real-time monitoring of mine air quality with an integrated ability to trigger countermeasures to reduce high concentrations of airborne contaminants in localized sections of mines. The SMAC system will be designed, tested, and refined in the laboratory environment before being demonstrated in an underground mine. This system will not only try to minimize the gaseous contaminants by regulating the airflow locally, but will also potentially employ a filtration system to reduce the airborne contaminants in case the maximum airflow capacity is reached. This paper presents development of the test apparatus for the SMAC system."

Jan 1, 2017

By Jeffrey R. Kelly, Paul M. Kubera, Richard A. Howk

Mixing of solid-liquid slurries is a unit operation that is widely encountered in the minerals processing industry. Applications may range from simple slurry storage in open tanks to complex chemical reaction systems under extreme conditions of temperature and pressure. The specific process requirements dictate both the degree of mixing required and the type of agitation employed to achieve the desired results.' Many continuous-flow process applications feature tanks operating in series to provide a discrete number of stages and a known residence time for the slurry. Because these tanks operate at a constant level in an overflow mode, the mixer must maintain uniform solids concentration and size distribution throughout the tank; failure to achieve uniformity results in accumulation of coarse solids in the tank, ultimately leading to a process or mechanical failure. Downward-pumping, axial-flow mixing impellers are widely employed to produce uniform solids suspension. The specific impeller type, number, size, and power draw is a function of each given situation. The use of high-efficiency, fluid-foil impellers (Figure I) has evolved as a recognized standard for these flow­controlled applications. Recent small-scale experimentation and full-scale experience has demonstrated that, when uniformity is required, capital and operating expense can be minimized by employing an additional upper impeller pumping in the upward direction.

Jan 1, 1995

By W. Baguley

There are many carbon-in-pulp and resin-in-pulp screening devices which are at present in use in the South African mining industry. Each one of these screens has been an improvement, from the very basic air cleaned and 'EPAC' types which were either circumferential or · diametrical launder screens, which were developed for C I P in the early 1980's, through to the more sophisticated LAP and Kambalda Screens. Each one of these screens not only increased the performance or throughput per square metre than its predecessor, but also addressed maintenance problems, wear, reliability and the ability to handle surge conditions, thereby preventing tank overflow. However, very little theory has been presented concerning, the flow of pulp through internal screens, carbon loss and screen wear rates. Almost all this information is based on empirical data. The NKM screen continued this trend and was able to offer flow rates in excess of 180 cubic metres per square metre of screen per hour and an average screen life of approximately six months. However, with increasing sophistication of the screen and the use of wedge wire as opposed to the normal woven wire, the mass was significantly increased and costs began to mount. Therefore, Mixtec undertook to develop a radically different screen, which incorporated many of the advantages of .the existing equipment and combined a few of its own.

Jan 1, 1992

By J. van Oldenborgh

The world market for bunkers represents some 140 MT (1980) of marine fuel oil and distillates. This is equivalent to 23CMT of coal, a potential market for steam coal larger than the total seaborne trade of steam and metallurgical coal today, and an obvious area which could contribute savings in world oil consumption. Oil bunkers are lifted fairly evenly throughout the world, the main supplying regions being Western Europe, the Middle East, North and Central America and Japan (Figure 1). Not surprisingly, the main customers are the tankers representing about 50 percent of the world market - (95 percent of the Middle East Market) - dry bulkers represent some 30 percent and general cargo ships the rest.

Jan 1, 1982

By Derek J. Barratt

The specification of the prime mover of an autogenous/semi-autogenous mill involves an analysis of the likely operating conditions within the mill and the choice of a nominal operating speed. For variable speed mills, the operating range for mill speed has to be defined so that mill power/torque requirement can be matched by the motor power/torque capability. This paper will describe how this relationship can be influenced by ore grindability.

Jan 1, 1993

By D. R. Dolinar, J. Pablic, D. C. Oyler, T. P. Mucho

At a mine in central PA, high horizontal stresses have caused long running roof falls resulting in hazardous conditions for the miners and the premature abandonment of panels. Because of these conditions, the mine requested assistance of the National Institute for Occupational Safety and Health (NIOSH) in utilizing the "advance and relieve" method to mitigate the affects of horizontal stress on the mine roof. "Advance and relieve" mining involves the removal of a pillar or a portion of a pillar during development, thereby creating a cave along one side of the panel. Following cave development, the horizontal stress is relieved over the workings adjacent to the cave in the active panel. The mine has used this system in three panels with a significant reduction in stress damage and no large roof falls.

Jan 1, 2001

By Kefton H. Teague

History of the feldspar industry in the United States has been summarized by DuBois (I)*. The earliest production of feldspar in the United States is reported to have been from Mitchell County, North Carolina, about 1744, with the product shipped to England, In about 1825 several pegmatites were worked to a limited extent in Connecticut, with the production shipped to England. The first feldspar grinding facility was constructed about 1850 in Connecticut, with chaser mills used. Feldspar has been produced continuously in the United States since about 1870. Feldspar is produced from the following states: North Carolina, California, Georgia, Connecticut, South Carolina, South Dakota, Kansas, Oklahoma, Virginia, Arizona, and Wyoming. Total United States production for 1969 will amount to approximately 900,000 tons. The most current published figures for world production is 1966, at which time 2,165,000 tons was produced. It is estimated that world production of feldspar for 1969 will amount to 2,410,000 tons. Historically, feldspar has been produced by hand sorting and hand cobbing of coarse block feldspar obtained from the intermediate and wall zones of zoned pegmatites. In the United States the reserve of known block feldspar, recoverable by hand sorting is nearing depletion. More emphasis is now placed on feldspar sources contained in finer grained rocks, especially coarse granites or fine-grained pegmatite and beach, dune, and river sands from which the feldspar is obtained by beneficiation.

Jan 1, 1970

By Robert D. Schmidt

The Bureau of Mines is conducting an investigation to develop remediation techniques for residential water wells whose yield has been affected in the long term, by underground mining. Initial work relating to this project was conducted in 1984-1987 at a room and pillar mine in Indiana County, Pennsylvania. Piezometer nest data from the room and pillar mine reveals that a downward gradient in piezometric head exists in shallow strata as a result of drainage into the underlying mine void. The vertical gradient in head in turn results in well bore leakage in open-hole water wells. The relative yield of valley wells is only slightly affected however because the high surficial recharge rate through fractures more than compensates for fracture leakage into the underlying mine. The relative affect of well bore leakage on well yield is greater in certain hillside and hilltop wells that have comparatively low inflow rates at shallow depths. The static water level of such wells is determined to a much greater extent by the chance interception of deep outflow fractures, than is the case for wells drilled in a more intensively fractured valley bottom. The lower static water level of wells that intercept deep fractures does not necessarily reflect the water table conditions outside of a small radius around the affected well. The results suggest that permanently isolating well bore outflow fractures may remediate certain open-hole residential wells that have been affected by high extraction underground mining.

Jan 1, 1986

By B. K. Slone

The depth at which it becomes more economical to use slope access as opposed to box-cut access for near-surface coal reserves, termed "transition depth," can be established for a given coal property by considering cost estimates for those parameters that determine respective access method. Fourteen parameters that influence access cost were identified and ranges determined. A Transition Depth Formula was developed to permit determination of the better method of accessing a reserve, given such information as highwall slope, road width, total bench width, pit dimensions, road grade, belt component costs, pumping costs, and cost of overburden removal and reclamation. In most cases, in Appalachia, studies indicate that the transition depth ranges between 20 and 30 m.

Jan 1, 1998

By A. Haile, A. Poole

During 2001-2002, the Granny Smith Mine of Western Australia undertook the development of a planned circular failure. Excavation took place in an interim pit wall that intersected the transported sediments, lake clays, and palaeo channel sands that overlay the deposit. The purpose of the study was to refine feasibility level slope parameters used for the initial design of the Wallaby pit, with the intent of increasing the overall slope when excavating the ultimate pit limits. During excavation, the geological and hydrogeological characteristics were studied in detail and data was collected using area-specific instrumentation and monitoring. Failure occurred in mid February 2002, at which time a detailed survey of the excavated slope using laser technology was conducted to provide geometric information suitable for back analysis of the material shear strength. The slope failure and associated information was analysed by geotechnical consultants. The revised shear strength and hydrogeological parameters were then applied to design the final pit walls. The slope redesign provided a cost saving of approximately seven hundred thousand US dollars. Design, slope formation, back analysis, the geology of the clay units, the hydrological environment, planned infrastructure, management and safety issues, and the on-going slope performance of the final slope are discussed.

Jan 1, 2004

By Richard J. Robbins

Mechanical raise and tunnel boring are new techniques to most of the mining industry. Coal, salt and potash have been bored economically, but until recently boring machines were not designed specifically for rock boring in underground mining. The construction industry has led the field of rock boring since 1854 when the first tunnel boring machines built by James S. Robbins and Associates went to work at Oahe Dam, South Dakota. Since that time the company has built boring machines for tunneling through ground conditions varying from cohesionless soil to hard rock, and in diameters ranging from 7 feet to 36 feet 8 inches. It is natural that the construction industry got the jump on mining with the use of mechanical rock boring equipment. Mines have looked for the long range answer to problems of underground excavation and they have chosen proved and established techniques they expect to employ for the next ten or twenty years. The mine development was laid out to accommodate these techniques.

Jan 1, 1964

By Leon J. Jacobs, Kyle R. Ott

This paper discusses design and construction aspects of the tunnel, shaft and station for the Weehawken Tunnel and Bergen line Avenue Station. The project consists of a 1,269 m (4,156 ft) long existing railroad tunnel, which will be enlarged and equipped with a two-track light rail system. The project also includes construction of a deep underground station, with a large shaft connecting the surface station to the below ground station for access and ventilation purposes. Vibration and noise from blasting is a critical community issue and blasting adjacent to two 230-kV duct banks located in the tunnel invert required special blasting procedures.

Jan 1, 2003

By B. K. Mishra, R. K. Rajamani

Discrete element is a numerical technique for describing the collision dynamics and motion of an assembly of particles. In particular, calculations are done on full three-dimensional space with a force-contact law for collisions and Newton’s law for subsequent motion. It may be said that there is no empiricism in this approach. The paper describes the full scale simulation of large diameter semiautogenous grinding mill of size 40X24 ft. It is shown that the simulation predicts the power draft of plant size mill extremely accurately. Also these simulations have been adapted uniquely to assess the motion of pebbles and slurry in pulp lifters. The passage of slurry from pulp lifters into trunnion is extremely important since flow-back and carryover must be avoided at all cost. The dynamics of slurry flow through pulp lifters is also described in this paper.

Jan 1, 2003

By N. J. Ferguson

An upsurge in demand for Australian coal has seen a much needed programme for a new generation of coal ports. This paper discusses design concepts in planning a large modern terminal, with the 25 Nt/a Port Kembla and the 50 Mt/a Newcastle facilities as practical examples. The need is emphasised for a studied Master Plan, in-built materials handling flexibility and staged development. Trends in bulk ship design and loading methods are noted. Features of these Australian designs include methods of dealing with poor ground conditions, functional civil engineering for environmental protection and optimal marine structure designs.

Jan 1, 1982

By J. A. Jirestig

Laboratory investigations on the possibility for magnetic separation of sulphide minerals are reported. A survey of several sulphide ores and flotation concentrates shows that magnetic separation in most cases is not a suitable primary method of beneficiation. However encouraging results have been obtained in concentrate purification. At the Boliden complex sulphide ore concentrator in Garpenberg a Allis-SALA MK III carousel High Gradient Magnetic Separator (HGMS) is used together with a small flotation circuit to recover sphalerite lost to the galena concentrate in lead flotation. The result after four years of refining the HGMS process, show increasing zinc recovery and enhanced quality of the lead concentrate.

Jan 1, 1993