Search Documents

By Mitchell Gordon

Two mineral processing facilities in North America required near terminal density slurries to perform de-bottle necking in their circuits. The installation at Barrick Goldstrike to ensure efficient oxidation conditions and throughputs in the refractory ore treating autoclaves. The Kidd Metallurgical Division unit to provide a steeper tailings slope to extend the life of the existing tailings dam. To achieve these goals, both operations selected a Supaflo "High Compression" Thickener following on site pilot plant evaluation. Commissioning and the first year of operation is reviewed. Operating data is compared with the pilot plant data. In particular, unusual doughnut formation at Goldstrike and the effect of temperature on the terminal density at Kidd Metallurgical Division are discussed.

Jan 1, 1997

By E. E. Jones

The lignites of Arkansas, Louisiana and Texas are typically described as muitiseam deposits which contain quantities of day and sand in thin lenses or in admixture with the fuel itself. These materials are often included in the run-of-mine fuel and can have very adverse effects in the end use. Since May of 1982 the Dow Chemical Co. has operated a pilot plant for the beneficiation of lignites. This facility has successfully removed sand, clays and petrified wood from the lignite producing a fuel comparable to or better than the selectively harvested run-of-mine materials. The design, operation and results from this plant were presented by J. H. Everitt at the 1984 Coal Technology Conference.

Jan 1, 1986

Large deposits of eudialyte, a low grade zirconium bearing mineral, occur on the Southern Coast of Greenland in the Ilimaussaq intrusion. Various processes were tested in the laboratory to recover eudialyte from these ores, including flotation, leaching, gravity and magnetic separation. A combination of dry and wet magnetic separations has the advantage of simplicity and the least environmental impact for the location. This paper summarizes the results of laboratory testwork to develop a two-stage treatment process to recover the eudialyte by magnetic separation.

Jan 1, 1993

By J. R. Maxwell

The development, commercial installation, and operating performance of large capacity Maxwell Flotation Cells. Volumes ranging from 300 cubic feet to 2,000 cubic feet per flotation mechanism.

Jan 1, 1971

By A. R. Laplante

A novel methodology to estimate gold recovery by gravity is presented. The methodology makes use of a population balance model which represents gold liberation, breakage and classification behaviour and applies pre-concentration and recovery performance curves to gravity-recoverable gold to predict overall recovery. Derivation of the necessary parameters is explained and demonstrated using data from an actual gravity circuit and one projected application. The methodology makes it possible to estimate the performance of circuits with large gold circulating loads and relatively low unit recoveries (e.g. jigs), or with high recoveries on a bleed of the circulating load (e.g. Knelson concentrators).

Jan 1, 1994

By Charles F. Herbert

It is difficult to decide who most deserves credit for discovery of a mining district that has produced over 19.8 Mg (7,000,000 fine oz) of gold and still contains a large reserve of low grade ore. Fred Culver may have made the first discovery. In the summer of 1867, the ship's log of the Hudson's Bay Co.'s steamer Otter stated that Fred Culver had been found nearly lifeless from wounds, without provisions, but with some 2.3 kg (80 oz) of rough, placer gold in the bottom of his canoe; he told of finding a rich creek and an attack by Indians that caused the death of his two companions. The place of rescue was about 24 km (15 miles) southeast from the present site of Juneau. Possibly John Muir, the hero of modem environmentalists, should be given important credit. In 1879 he reported finding mineralization along what later became to be known as the Juneau Gold Belt, and it was his report that induced the cantankerous German mining engineer, George Pilz, to grub- stake some of the prospectors who had drifted into Sitka from the declining gold placers of Cassiar, British Columbia. Pilz also offered rewards to Indians who might report gold discoveries.

Jan 1, 1990

By J. K. Grunig

A process consisting of leach, continuous countercurrent decantation, resin-in-column ion exchange, evaporative crystallization of beryllium sulfate, and decomposition of the sulfate was developed for Spor Mountain, Utah, ores. The process is metallurgically sound, has a minimum of process steps, and is applicable to a wide variety of beryllium ores. The most novel aspect of the process is a resin system of ion exchange which is highly selective for beryllium and which rejects substantially all impurities except for minor amounts of aluminum, magnesium, fluorine, and sulfate in addition to beryllium. The oxide from sulfate decomposition meets specifications of potential users.

Jan 1, 1982

By Clark J. Gilbert

The mining method at the Cannon mine uses heading and bench stopes, which are subsequently backfilled with cemented high-strength fill before pillar removal. The dimensions of the pillars are 7.3 m wide by 19.8 to 28.9 m high (24 ft by 65 to 95 ft). They require careful blasting in order to not damage the rock, compromising pillar strength and complicating later removal. Additionally, the proximity of dwellings makes vibration control a must for good neighbor relations. A blast monitoring study was conducted in order to optimize bench blasting practices to maximize fragmentation, reduce costs, and to minimize wall damage and ground vibration. The Cannon mine is a joint venture between Asamera Minerals (US) Inc., a 92% owned subsidiary of Gulf Canada Ltd., and Breakwater Ltd. Asamera is the operator. The mine is located at the south end of Wenatchee, WA, a town of roughly 45,000 people on the eastern flanks of the Cascade Mountains. Gold is the primary product at the mine. The rock is extracted using a sublevel end-slicing method on 15 m (50 ft) lifts, with subsequent backfilling and pillar removal. The stope widths, dictated by rock conditions at 7.3 m (24 ft), are the same in the primaries as in the pillars, or secondaries.

Jan 1, 1990

By M. Modis

According to previously established theoretical analysis and under certain conditions, a critical sampling grid can be determined for an earth-related space-distributed natural variable. Sampling above this critical limit adds little to the mapping results, while based on this limit the ideal process of reproducing the original phenomenon is theoretically defined. The objective of this paper is the application of the above theory to the Klidi lignite deposit in Florina, Greece, where Public Power Corporation (Greece) has conducted a sampling campaign to estimate the deposit thickness and its heating value. Data acquired for these two variables were analysed in the space domain in order to derive their respective correlation functions. The structural analysis of the deposit generated two covariance models, one for the thickness and one for the heating value, from which the critical sampling grid was identified. The conclusion drawn is that in some parts of the deposit the sampling grid is denser than required. Finally, an optimal sampling grid is proposed in order to gain the maximum information at the lowest cost.

Jan 1, 2006

By Michael A. Trevits

A mine fire represents one of the most dangerous and challenging safety issues facing underground mine operators. Given the right circumstances, a mine fire can occur at any location in the active or abandoned mine workings, can quickly grow beyond control, and threaten the welfare and livelihood of the entire underground workforce. The National Institute for Occupational Safety and Health (NIOSH), in partnership with the Mine Safety and Health Administration (MSHA), has been conducting an in-depth program of research addressing mine fire prevention, early and reliable fire detection, and mine fire suppression technologies. One portion of this program is focused on understanding the characteristics of mine fire combustion products and flame spread through large scale deep-seated (firmly established) fire tests and use of computational fluid dynamics (CFD) modeling. In this study, two deep-seated fire tests were conducted; one fire consisted of coal material and the other utilized the two most abundant fuel sources found in a coal mine: coal and wooden cribbing blocks. The fires were burned to completion while the combustion products were collected and analyzed. In addition, an array of thermocouples was placed within the body of the material to measure flame spread rate. The coal fire test information was then used to develop a CFD model of the fire. This paper describes the fire tests, provides insight into characteristics of flame spread, and presents the CFD modeling work results.

Jan 1, 2009

By S. P. Singh

In order to understand the intricate nature of blast damage mechanism and to counter the associated problems, small scale blasting experiments were performed on hydrostone, concrete and granite. This was followed by a 2.4 m x 2.7 m (8'x 9') drifting operation in a quartzite quarry. Interior as well as exterior damage was assessed by different techniques. On the basis of the experimental results, the effect of explosive characteristics on the damage was examined.

Jan 1, 1992

By Y. Xi

This paper offers an algorithm to determine the optimal panel size with the objective of minimizing the overall stripping cost. The approach is presented both in analytical form for regular layers of coal and overburden, and in graphical form for the cases of irregular and multiple coal seams. When the optimal panel width needs to be changed due to some circumstance, we prove in general that increasing the panel width is better than reducing it in both economics and operational efficiency.

Jan 1, 1994

By N. T. Cowper

Slurry viscosity ultimately affects the majority of mineral extraction processes. However, to date its role has been disguised because mineral processing equipment has been conservatively designed to operate at minimal slurry viscosity. With most ores this still meant acceptable solids concentration was achieved. However, with the advent of treatment of weathered ores the resulting higher slurry viscosity (rheology) has meant solids concentration has had to be reduced, often to unacceptable levels. To permit operation at higher solids concentration chemical dispersants are employed. These dispersants are expensive and their addition should be controlled. Slurry Systems Pty Limited (SSPL) has developed an On-Line Viscometer to monitor and control slurry viscosity, whether by controlling water addition or by controlling dispersant addition. Using this instrument the slurry rheology can be controlled at the optimum level, maximizing solids throughput, and minimizing water, reagent, and dispersant addition. This paper discusses rheology of typical mineral slurries, the relationship between slurry rheology and percent solids in a slurry, and the need for rheological control in mineral processing. The effects of rheology on various process steps, and the use of dispersants are reviewed. The paper concludes with summarizing actual case histories and cost impact of Theological control.

Jan 1, 1992

By D. Tao

More than 80 million metric tons of fly ash is produced annually in the U.S. as coal combustion by-product. Fly ash can be converted to value-added products if unburned carbon is reduced to less than 2.5%. However, most of fly ash is currently landfilled as waste due to lack of efficient purification technologies to separate unburned carbon from fly ash. A rotary triboelectrostatic separator has been developed and patented recently at the University of Kentucky with unique features. Several fly ash samples have been used to understand the effects of major process parameters on the separation performance. The results show that compared to existing triboelectrostatic separators, the rotary triboelectrostatic separator has significant advantages in particle charging efficiency, solids throughput, separation efficiency, applicable particle size range. Key words: Coal, Combustion Waste; Fly Ash; Particle charging; Separation.

Jan 1, 2008

By S. D. Van Nort

The Grasberg porphyry copper-gold deposit of Freeport Indonesia Inc., an 81% owned subsidiary of Freeport-McMoRan Inc., lies within the Ertsberg Mineral District in central Irian Jaya, Indonesia. The Grasberg deposit was discovered during a drilling campaign initiated in early 1988. Production at the open pit Grasberg deposit commenced in December 1989. The Grasberg copper-gold orebody is contained with a young igneous complex of dioritic composition which intrudes limestones of the Tertiary New Guinea Group. Alteration is typical of porphyry copper deposits worldwide except that higher grade primary chalcopyrite with significant gold values is associated with a centrally located zone of strong quartz stockwork.

Jan 1, 1991

By W. N. Brown

One of the seemingly eternal problems with which we are frequently faced is that of providing adequate and economical warehousing facilities to store large quantities of bulk product. Seasonal consumption, transportation, marketing, and other factors very often dictate extensive product warehousing requirements for an operation geared for steady, year-around production of a material requiring weather protection during storage. Fertilizers such as potash and urea are examples of such products; the consumption of these materials is extremely heavy in the early spring at which time the materials must be placed in the soil, whereas, for obvious operating efficiencies, production is more or less constant for a given operation throughout the year.

Jan 1, 1961

By Donald L. Freed

Design, development, factory test, and in-mine evaluation plans are presented for an Automated Extraction System (AES) that has been designed to fill needs which are present in the Mining Industry. The philosophy of design and proposed operation of the machine, as well as the relationships between these factors, and final machine configuration are reviewed. The AES is designed to overcome production problems resulting from the regulation of roof control, clean-up, ventilation, dust suppression, and operator protection required by the Federal Coal Mine Health and Safety Act of 1969. The design permits more continuous operation and greatly improves operator safety. The machine is a full-face drum-type continuous miner which includes self-advancing, continuous temporary roof support. Onboard self-advancing face ventilation, dust suppression, and air scrubbing equipment are also included in the design. A further improvement over existing equipment is the incorporation of an automatic programmed cutting cycle control system. All mining functions including movements of the roof support system are handled by this automatic system.

Jan 1, 1977

By N. Del Bel Belluz

Drilling underground in the Grasberg De-watering drifts has routinely hit water aquifers with high flow rates and pressures. Two types of holes are utilized; pilot-holes to probe ahead of the tunnel development to intersect aquifers ahead of the face; and de-watering holes to de-water rock formations that will drain water from the Grasberg pit and allow tunnel development to proceed safely. Recently, rates of 1050 psi static pressure have been recorded with flows from a NQ hole measured at 1350 gpm (US). The water flows can be slightly acidic, necessitating the use of stainless steel collar gear to resist corrosion. These rates were anticipated and contingencies were planned early to deal with these conditions. The collar gear is used to control water flows whereby the water is treated as an important resource. As a result, pm has established procedures to maintain safety of the drill crews, enable coring of the rock and to maintain safety of the miners who are driving the drifts.

Jan 1, 1998

By J. M. W. Mackenzie

Three major developments have dominated the recovery of gold from ores, viz; 1846 Elsner's studies of gold solubility in aerated alkaline cyanide solutions 1887 MacArthur and Forrest's process based on zinc precipitation 1980+ Large scale development of the CIP process The brevity of this list for a metal whose extractive metallurgy has been as widely studied as any metal reflects the fact that the chemistry of the gold recovery process, as opposed to the engineering has seen few significant breakthroughs in over a century of application. to The purpose of this paper is introduce a new chemistry for gold recovery which may, in the future, add significantly to the technology of gold recovery. This new chemistry is based guanidine functionality - (R2R2N) 2 C = N R2 on the In developing the use of the guanidine functionality for the recovery of gold as the aurocyanide anion from leach solutions and pulps, Henkel has, as its objective, the development of an effective gold selective ion exchange resin. As will be seen, the initial investigation of the properties of the guanidine functionality in the solvent form for gold recovery lead to some significant metallurgical developments of their own but, the foremost objective was, and remains, the development of a resin for gold recovery. As a part of this development project, Henkel has entered into association with Mintek, South Africa, and this ongoing association has the potential to develop RIP/RIS technology for the gold industry. More details on Henkel's gold recovery technology and Mintek's role in this programme are given in (1). an The application of ion exchange resins to gold recovery is not new and many reviews have been published on the advantages of this process, and on the current state of the art of gold recovery by ion exchange resins. (2)(3)(4) Widespread application of ion exchange resin based processes for gold recovery has, however, not occurred to date. Fleming and Cromberge (5), described some significant pilot plant RIP trials in South Africa and the partial success of these pilot plant trials held out the tantalising possibility of a breakthrough in gold recovery based on RIP technology. Despite this pioneering work, only two really significant applications of RIP technology for gold recovery exist today. These are the Golden Jubilee Plant in the Eastern Transvaal South Africa and the widespread, although in some respects technically backward, use of ion exchange for gold recovery in the former USSR. There are two main reasons for the current scarcity of RIP and RIS plants used for gold recovery. These are: 1. 2. The perceived problems of engineering RIP plants The lack of a resin having suitable chemistry for both gold loading and gold elution The problems of engineering RIP plants have been largely overcome in the last 25 years. Much of the development in RIP plant design took place in the uranium industry during the rapid expansion of that industry in the mid 1970's. In addition, the development of CIP engineering systems has lead to the development of in-pulp solid extractant based metallurgical plant designs which can, with limited modification, be adopted to RIP. The lack of a resin having suitable chemical properties has almost certainly been the main reason for RIP/RIS not being introduced into the gold industry over the past decade. Attempts to use RIP/RIS have focussed on either conventional we ak base or conventional strong base resins. The weak. base resins have the disadvantage that they

Jan 1, 1993

Computer programs commonly used to simulate mining operations generally require a fair amount of data. The common data input methods have been by either creating an ASCII data file or answering numerous questions during the data input phase. Both methods of data entry are tedious, time consuming, and inflexible. A screen handling system has been developed to drive FORTRAN-77 application software for the MS-DOS environment. The system utilizes keyboard functions with an aid of extended ANSI codes. It also allows a multi-view input data entries.

Jan 1, 1990