Search Documents

By J. K. Brooke

Fluorine is a lively element in both its chemical and economic behavior. It was not isolated as an element until 1886 by Moissan. However, its principal source to this day, fluorspar, was known and its special merits recognized long before that time. Our own mining brother, Agricola, is credited with having named fluorite, the mineral name, in 1546 from the Latin, "fluere", to flow. It made things melt and was already being used as a flux. Because fluorspar has been found as a relatively common gangue mineral in metal ore veins, it has long attracted the attention of geological thinkers seeking to, explain the whys and wherefores of veins. Fluorine has been thought of as one of the principal mineralizers, holding metals in ascending vein solutions for deposition close enough to the eventual surface to be accessible for profitable mining.

Jan 1, 1964

By William J. Shampine

This map shows general trends of the chloride concentration of water in the upper part of the Floridan aquifer. Below this part of the aquifer, high chloride water can be found everywhere in the State. The accompanying cross section shows the depth to salty water across central Florida. In the center of Florida, fresh water may be found as deep as 2.000 feet, whereas, along the coast it may extend no deeper than about 200 feet. Chloride concentration in small local areas may deviate from the values represented on both the cross section and the main map. This map shows general trends of the chloride concentration of water in the upper part of the Floridan aquifer. Below this part of the aquifer, high chloride water can be found everywhere in the State. The accompanying cross section shows the depth to salty water across central Florida. In the center of Florida, fresh water may be found as deep as 2.000 feet, whereas, along the coast it may extend no deeper than about 200 feet. Chloride concentration in small local areas may deviate from the values represented on both the cross section and the main map.

Jan 1, 1966

By Gilman Y. Murray

The problems connected with the development of economically acceptable water supplies in arid regions are discussed. The techniques for capture and retention of runoff from infrequent desert storms are described and the major factors involved are emphasized. The exploration and planning for a typical water development in southwest United States is described, including an analysis of capital and operating costs for the proposed system.

Jan 1, 1963

Laboratory testing by the Federal Bureau of Mines has shown that the removal of insoluble slimes using selective flocculation and flotation is a viable method for treating low-grade potash ores which have a high content of water-insoluble impurities. Results indicated that up to 85 percent of the insoluble slimes could be removed from sylvinite ore containing 5 percent water insolubles and 13 percent K20 using nonionic or cationic polyacrylamide flocculants and cationic, anionic, and/or nonionic collectors. Subsequent potash flotation recovered up to 88 percent of the potash in rougher concentrates containing 47 to 57 percent K20. Sizing and cleaner flotation of the rougher concentrates upgraded the products to 60 percent K20. Filtration of the insoluble slimes flotation concentrates recovered 87 to 0 percent of the brine. Flotation concentrate filtration rates were 7 times faster than the filtration rates of mechanically deslimed products.

Jan 1, 1977

By S. N. McIntosh

Column bioleaching was evaluated by the U.S. Bureau of Mines as a means of recovering manganese from a low-grade ore from the Three Kids deposit in Southern Nevada. Manganese was solubilized from the ore using indigenous heterotrophic microorganisms. Diluted molasses medium was provided as nutrient for the microorganisms. The medium was recirculated through the ore bed until the sugars were spent. Two methods were evaluated to recover manganese from the sugar depleted bioleaching solution: (1) adsorption with a weak cation exchange resin followed by stripping and precipitation techniques, and (2) direct precipitation of the manganese using ammonium carbonate. Both methods removed up to 95 pct of the solubilized manganese from the medium as a carbonate salt. After manganese removal, the medium was replenished with fresh molasses and recycled back through the column. More manganese was effectively leached. This process of manganese solubilization and recovery followed by replenishment and recycling of the medium was repeated until 98 pct manganese was extracted from the ore.

Jan 1, 1993

By K. V. Raj

"The development and advancement of computational fluid dynamics (CFD) has made it possible to better understand pollutant flow and distribution in deep open pit mines. Open pits located at higher latitudes, especially in the Arctic and sub-Arctic, face a unique problem due to atmospheric temperature inversion, which is prevalent during much of the winter. A three-dimensional CFD model of an actual open pit mine in the Arctic was developed to analyze the problem of pollutant growth during inversion, and mitigation of the pollutants through improved ventilation schemes. Due to the availability of mine-specific data, such as contaminant concentrations and coordinates of sampling locations, the actual 2013 pit geometry was used for model validation Concentrations predicted by the selected realizable ?-e turbulent model are compared to measured pollutant concentrations at the open pit. Pollutant concentrations at selected locations showed differences, but remained within the same order of magnitude in most cases. INTRODUCTION Computational fluid dynamics (CFD) has emerged as a useful tool for ventilation modeling in underground mines (Edwards and Hwang 1999, Purushotham and Bandopadhyay 2009, Wala et al. 1998, Xu et al. 2011). Application of CFD in open pit mines has been limited, however, since most open pit mines located at lower latitudes do not encounter considerable ventilation problems. Open pits located at higher latitudes, especially the Arctic and sub-Arctic, face a unique problem due to atmospheric temperature inversion, which is prevalent during winter. A number of Russian researchers have tried to understand the air inversion and resulting pollutant transport problem by modeling air flow phenomena in open pit mines (Baklanov and Burman 1996, Baklanov 1984, Baklanov 1995, Belousov 1985, 1989, 1995). Much of their work, however, was based on numerical models and methods of finite difference. Baklanov (2000) applied a modified ?-e and a ?-l CFD model to air flow phenomena on various terrains. More recently, Choudhury (2011) used the COMSOL CFD package for modeling pollutant transport for an idealized open pit mine. Collingwood et al. (2012a, 2012b) used a two-dimensional model for fluid flow and contaminant transport at an Arctic open pit mine. The authors have also previously presented work on CFD modeling of an actual open pit mine at high latitude (Bandopadhyay et al. 2014, Raj et al. 2015a). However, the CFD work done by the above-cited researchers lacked model validation with field-measured data. Validation of a developed model is important in assessing the quality and accuracy of the predicted results. In general, experiments are done numerous times in controlled environments to assess the validity of collected data. There are two types of assessments used in CFD simulations: (1) verification and (2) validation. Model verification is checking the accuracy of the computer codes during the implementation phase of a real-world problem, within the specific limits of accuracy (Oberkampf and Trucano 2002). Since, the pollution transport model presented in this paper used the commercial ANSYS-FLUENT CFD package, verification is not needed as the program has been tested widely, and verified numerous times."

Jan 1, 2016

By K. L. Browne

After a decade of high copper prices, major mining companies are renewing their interest in purchasing operating properties and/or developing ore bodies. An existing operation carries with it a history that can present unique opportunities, while a greenfield operation allows for the establishment of a defined culture. Capital investments are distinctly different. A comparison of BHP Copper's Robinson operation, a greenfield property, and BHP Copper's Tintaya operation, a government owned Peruvian property, will provide insights into mining, concentrating and cultural differences between North and South America operations. The Broken Hill Proprietary Co. Ltd. (BHP) is Australia's second-largest company. Fiscal year 1996 sales were US$16 billion, profits were more than US$1 billion and total market capitalization was about US25 billion. In 1885, BHP began mining silver, lead and zinc at Broken Hill, New South Wales, Australia. Throughout its 112-year history, BHP achieved an impressive record of performance and expansion. Today, BHP is one of the world's leading companies (66th on the Standard and Poors 500), having diversified into steel, petroleum and mining with more than 65,000 employees in 70 countries.

Jan 1, 1997

By John K. Liu

The trend to larger grinding mills, requiring total drive power in the range of 10,000 KW(13,400 HP) or so provides the incentive for developing new power transmitting techniques, since conventional girth gears are limited to about 3700 to 4500 KW per mesh (5000-6000 HP). For the immediate future, the synchronous motor, with its beneficial power factor, and the squirrel cage induction motor, with its high reliability record and low maintenance, still promise to be the best choice for prime mover(s). Due to the abovementioned single mesh power limitation of the gear train, however, two or more motors must be combined to attain the required drive power. This paper describes a scheme for coupling these motors to the mill using a straightforward, essentially mechanical means that is based on proven components and controls.

Jan 1, 1977

Laboratory tests were conducted to evaluate the silica collection efficiency of flooded-bed scrubbers with six different filter panel designs and at two operating velocities. Test results indicated that reductions in filter density negatively impacted respirable dust collection. Silica collection efficiency for the least dense filter was as much as 33 % lower than the collection efficiency of the densest filter. At the low operating velocity, the least dense filter allowed over 40% of the respirable silica dust in the scrubber intake air to pass through the unit, where it would be discharged back into the mine environment. Operation of the scrubber at the higher test air velocity increased silica collection efficiency, regardless of the filter panel tested. The density of the filter panels also impacted the quantity of air that is moved through the scrubber, with higher density filters reducing scrubber airflow. For each filter, the relationship between dust collection efficiency and air moving capacity must be considered to determine overall effectiveness for specific mine applications.

Jan 1, 1998

By H. EI-shall

The conventional beneficiation scheme for Florida phosphates involves reverse flotation with an intermediatory acid scrubbing step. A single reagent flotation process, using fatty acids or amine as the collector, would eliminate the scrubbing step along with the other flotation step. This can not only simplify the process flowsheet, but also result in reduced reagent costs. The potential of single reagent flotation of Florida phosphates using fatty acids as the collector was examined in this study.

Jan 1, 1993

By J. G. Groppo

A beneficiation process has been developed to provide selective separation of unburned carbon from high LOI fly ash. Previous reports of utilizing froth flotation to achieve selective separations required long residence times and high reagent costs. A proprietary reagent system has been developed to address both of these limitations. Based on the results obtained from laboratory and pilot-scale investigations, a flowsheet design has been developed to produce two distinct usable products from class F fly ash; low LOI ash and a high carbon product suitable for reburning or further upgrading. A process flowsheet and description are presented.

Jan 1, 1996

By Douglas W. Barr

Water is a necessary part of our environment. It is a biological necessity, but more than that, it is a necessary part of our life style. Those of us who live in the north woods expect water to be part of the scene. There are few natives of this region who would be content to eliminate the streams, the lakes, the marshes, or our forests. Throughout the world, water has been so much a part of man's environment and man's adaptation to life has been so closely tied to water that our way of life and ways of accomplishing our work include water as an essential tool. The production of taconite is an example of our dependence on water. Other methods could have been developed to process taconite ore but the process methods chosen utilize water. Water is used for grinding and separation and for trans- porting the ore from one part of the process to another and for dust control. A typical large plant producing 10 million tons of taconite pellets per year will have on the order of 130,000 gallons per minute (8.202 m 3/51 of water in circulation in the plant. About 120,000 gal. per min. (7.571 m 31s) will pass to tailing thickeners where 110,000 gal. per min. (6.940 m 31s) is separated from tailing and returned to the process. About 15,000 gal. per min. (.9464 m 31s) goes with thickened tailing to tailing basin. My point is that there are great volumes of water in motion in a taconite plant,

Jan 1, 1980

By J. Herbst, C. C. Harris, G. Poling

The modern flotation machine is the result of decades of adaptation to a changing environment. In response to falling ore grades, and rising demands, tonnages, and costs, attempts are now underway to expand machine capacity by about an order of magnitude, while at the same time maintaining metallurgical performance and if possible reducing power requirements per unit throughput. Empiricism and rule-of-thumb have guided flotation machine design and scale-up, and a current need is for the development of a fundamental understanding of the subject. Design features of current and some obsolete machines are discussed in an attempt to outline those principles of flotation machine design which are known, and to delineate topics needing investigation. Attempts are made to distinguish between essential machine features required by the physics of the process, those features resulting from speculative theories on the flotation mechanisms, and features which are essentially styling variations. Topics discussed include: flotation mechanisms; tank and impeller/ stator design and dimensions; impeller speed; aeration; power consumption; particle suspension and dispersion; capacity; correlation of design parameters and operating variables; scale-up and scale- down; materials flow; problems in machine design. Design details and operating data for several current machine families are provided in Appendices.

Jan 1, 1976

By P. R. Taylor

The ability to treat refractory gold concentrates that contain appreciable amounts of sulfur and arsenic, in an economic and environmentally safe manner is important to the gold mining industry. Processing alternatives include: autoclave oxidation, bacterial oxidation and roasting. Roasting may be the cheapest of all the alternatives if inexpensive methods can be found to contain the arsenic and sulfur. The research program, being reported here, has been evaluating the ability to use hydrated lime in the roaster to capture both the arsenic and the sulfur. Lime roasting is not a new idea, it was proposed for copper ores by Bartlett in the early 1970's (Bartlett and Haung 1973) and for cobaltite concentrates by Taylor in the early 1980's (Taylor et al., 1981). In addition, ores have been roasted that contained limestone and it was shown that partial capture of the sulfur was possible. Lime -sulfur containment has been proposed for the coal fired electricity industry, as well.

Jan 1, 1992

By William H. Mount

INTRODUCTION The requirements of mine ventilation demand the constant attention of the mine operator. Just as the physical mine structure changes with time, the ventilation requirements of a particular mine change considerably from season to season and even from day to day. No ventilation system can remain adequate indefinitely; and all systems require monitoring and adjustments to achieve proper ventilation. Instead of being given fore- thought and planning, mine-ventilation systems too of- ten are erected hastily, merely to correct an already un- healthy situation. The usual result is an inefficient and costly system that, in some instances, may prove in- effective in providing fresh air to the point of need. The ventilation of mines is a combination of both art and science. The fluid that must be moved is in- visible; its properties change drastically with temperature, barometric pressure, and humidity; and the methods of measurement are not precise. In part, ventilation engineering must rely upon the art of good industrial ventilation experience and sometimes even the trial-and- error method. However, the properties of air can be determined with relatively inexpensive equipment; with some care, measurement accuracies within 5% of the actual values can be obtained. Thus the art of ventilation gradually is being supplanted by improved engineering practices. Although the direction of flow and the volume may not be predicted correctly by airflow equations in every situation, it is better to try to predict the behavior of a given ventilation before installation than to proceed blindly with a system design. When used with the discretion that comes from education and experience, the basic laws of ventilation can provide sub-stantial insight into the design of an air-handling system; and they can prevent wasteful or even dangerous designs from being installed. Since the mine operators who read this text will have varying amounts of exposure to ventilation theory, the basic laws of airflow and of mechanical ventilation are presented in the first section. The emphasis has been placed on the interpretation and use of fan characteristic curves that are supplied by fan manufacturers. Considerable information can be obtained from these fan curves, particularly when they are used with a graphic model of the mine, drift, or duct in which the fan or fans are to be installed. A few minutes spent comparing the various characteristic curves can help the designer obtain the correct fan for the job. However, the under- standing of a few fundamentals is necessary; and this text has been prepared to provide ample and understandable information in a "how-to" style. In subsequent sections of this text, more down-to- earth subjects will be covered, including the problems of air recirculation, relative merits of installing fans in series or in parallel, expected maintenance requirements (vibration, lubrication intervals, etc.), fan noise and some remedies, effect of an inlet bell on the fan per- formance, basic air-measurement techniques and equipment, and similar miscellaneous items. Although this text is not intended to be a comprehensive bible of mine ventilation, it has been prepared as a guide that provides some useful information to individuals responsible for the quality of the underground environment. Every person working underground is en- titled to the safest environment that can be provided within the limitations of existing technology and at a reasonable cost. Adequate ventilation is well within both limits, provided that the system is designed intelligently, in conjunction with the mining plan, and not as an after-

Jan 1, 1982

By Joseph G. Wargo

The purpose of this paper is to investigate trends in exploration expenditures of a selected group of mining companies for the interval 1968 through 1971. The paper also compares these trends with other financial factors that are associated with various groups of companies and comments on the implications of these trends. Although a four-year interval is hardly enough time to establish a long-range set of trends from which operating rules can be derived, the fact that the four years selected are in the immediate past gives some sense of relevance to the matter of exploration expenditures at the present time and in the near future. The sample under study here consists of 21 mining companies. Of these, 19 are listed on the New York Stock Exchange and 2 are listed on the American Exchange. Twenty are American, one is Canadian. All are fundamentally "mining companies" in that they derive the bulk of their income from the extraction, sale, and at times, fabrication of metals from their own mines. This is in contrast to companies which have mineral exploration departments but derive the bulk of their revenues from sources other than mining; for example, from oil and gas sates, Also, no companies which can be considered strictly as exploration companies are included in this study. Although this definition held up fairly well when studying this list in 1968, the strict application of this definition became more difficult through the years up to the present time. In 1971, three or four of the companies were changing their character in that they were phasing out of the mining business, and either deriving their income or planning to derive a substantial part of their income from activities other than mining. A study of

Jan 1, 1973

By William Lodding

That grinding may change a crystalline material both in a physical and in a chemical sense has been shown by a number of authors in recent years. Thus Mackenzie (1) and Bartha (2) reported the effects of careful grinding on muscovite, quartz, gypsum, dolomite, etc. Increase in specific surface produced by grinding implies increase in total energy of a system. Newly produced surfaces are chemically more reactive; dislocations may be introduced during grinding, and existing strain may be released by the same process, as shown by Holt et el. (3) All these changes are easily detected by thermal analysis, but it is not easy to separate the multiplicity of effects registered and to arrive at quantitative interpretations. This paper is an attempt to analyze by the use of thermal analysis some effects produced in grinding. In differential thermal analysis (DTA) one measures all thermal changes occurring in a substance during heating or cooling. Chemical changes, such as decompositions, synthesis, oxidation, reduction, etc., and physical changes such as phase transformations, changes in specific surface and in thermal conductivity, strain release, etc. By thermo gradmetric analysis (TGA) on the other hand only chemical changes involving weight loss or gain are recorded. Similarly gas evolution analysis (GEA) will register only reactions involving gas evolution, including water vapor, and oxidation-reduction. By performing two or all three of these thermal methods of thermal analysis simultaneously and on the same specimen one can separate the different effects registered and by difference evaluate their magnitude.

Jan 1, 1966

The Coal Utilization review arrived too late to appear in the May issue. Coal utilization technology is improving due to the urgency with the 1990 Clean Air Act and the incentives provided by the Clean Coal Technology (CCT) program. Advances in the CCT are the subject of this report because of their broad industry application, support and involvement. Clean coal demonstration program Projects in the $5 billion Clean Coal Technology program are jointly funded cooperative agreements - not contracts - between government and industry. The industry participant in each project contributes at least 50% of the total cost. The participant takes primary responsibility for the project and is awarded any patent rights for inventions that may occur during the demonstration. The government, on the other hand, ensures that schedules are met, costs are controlled and project objectives are met.

Jan 1, 1991

By R. H. Mullennex

Application of depositional analysis concepts is becoming an ever-increasingly more important and more useable tool in exploration and development of coals in the Appalachian basin. Over the past decade, a rather large number of studies, papers, and publications have addressed various aspects of depositional environments of coals and, to some extent, applications to development. As would be expected as regards a subject so complex as Pennsylvanian sedimentation in the Appalachian basin, certain academic studies have produced conclusions at variance in some aspects to those of other studies. Overall, however, there has been a building- block progression and general refinement with time of understanding of the depositional settings and other factors controlling Appalachian coal distribution, quality, and other minability parameters. Most attempts to explain coal seam characteristics have revolved around a basic deltaic model. Some have attributed certain seam attributes to upper delta plain deposition, other attributes to transitional-lower delta plain settings, and yet others to lower delta plain environments, and so on. While these approaches have provided valuable insight into some general coal characteristics, they are somewhat incomplete and are, in a sense, too broad for specific mine-scale applications. Further, it is apparent that in order for widespread peat accumulation to occur, there must be a drastic decrease in the energy of the depositional system and amount of sediment being brought in, compared to the active deltaic and coastal processes responsible for deposition of the large volume of clastic sediments that dominate the Pennsylvanian system of the Appalachians. Consideration of this fact implies that peats (coals) may not necessarily reflect depositional settings that are directly coincident with those associated with adjacent rocks. Cecil and Englund (1985) address this point, and quite correctly state that "the primary controls on major stages of peat formation are allocyclic processes involving paleoclimate, eustatic changes in sea level, and tectonics." While this statement is inarguable, it does not negate the importance and usefulness of depositional analysis in predicting reserve characteristics that may impact mining and marketability.

Jan 1, 1986

By T. P. McNulty

During the last decade, many exhaustive studies have been made of process energy requirements for the production of various metals and materials. Some excellent technical papers and text books have resulted, and some of these are included in the bibliography of this paper. These studies were, of course, prompted by the economic pressures which resulted from the beginning of the "Energy Crisis" in 1973. Our intensified consciousness of the cost of energy led, then, to a greatly improved understanding of the energy consumption attributable to individual mining, processing, and refining steps. It is worth noting, however, that an awareness of the cost of energy is not new and that efforts to minimize this cost were an important part of sound mine and plant management practice throughout the earlier days of our industry. One only has to read a few accounts of mining operations around the beginning of this century to develop an appreciation for the cost of supplying wood, coal, fuel oil, or electric power to remote locations.

Jan 1, 1983