Search Documents

By Thomas V. Falkie

Of the various critics of federal energy and minerals policy we are hearing these days--and they are legion--few make their points more vividly than our fellow SME member and eloquent spokesman for the mineral industry. Mr. Eugene Guccione. In a moment of comparative mellowness. Mr. Guccione recently characterized Washington's time-honored legislative and bureaucratic machinery as a case of "...scientific illiterates asking the incompetents to do the unnecessary." I hope the prevailing industry view of government is not quite that harsh, and yet one cannot deny that government intervention is indeed pressing in on the mineral industry with increasing force. What is happening today in Washington and in state capitols will have enormous impact--both short and long term--on the future of coal and mineral production in the United States. Symptoms of this trend are everywhere. In the first place, there is a sentiment, widely held and still spreading, that the government must become involved-- that no matter what the problem, the solution lies in more government intervention. Free enterprise versus statist, reflex reaction organizations. When it cones to regulation in the resource field, there is too often a tendency to start out by assuming guilt on the part of the mineral industry. This can lead to laws governing mineral recovery that are more punitive than constructive...laws drawn up with little research into the scientific or economic considerations involved.

Jan 1, 1975

By M. Mathiba

High CO2 fluxes associated with reclaimed coal mine spoils pose an environmental hazard where such sites are used for building. CO2 concentrations in excess of 25% have been reported in homes constructed on or down gradient of such spoils. The objective of this study was to investigate the effect of a mitigation trench used at one mine site on CO2 fluxes across the trench using chamber?based trace gas measurement. LI8100 automated CO2 flux system was used to measure CO2 fluxes from 32 sample points located across a deep mitigation trench on June 8 and 9. The maximum recorded fluxes were 7.29 and 8.18 µmol/m2/s, with averages of 4.15 and 5.50 µmol/m2/s, up and down-dip respectively. These preliminary results show CO2 flux is higher up-hill than down-hill at 95% significant level. This work shows that flux measurement can be used to investigate CO2 migration on reclaimed mine land. Further work is necessary to allow geostatistical modeling of the spatial variability of CO2 fluxes over reclaimed coal mine spoils. Knowledge gained would assist mining practitioners and regulators in reclamation planning for envisaged post-mining land uses.

Jan 1, 2010

By J. M. Scharer, Bruce E. Halbert, Pettit. Carol M., Lysane Bolduc

The ratio of neutralization potential (NP) to acid production (AP) ratio is often employed for predicting acidic discharges from waste rock dumps. The available NP was evaluated in laboratory studies of limestone dissolution in simulated acidic mine water. The available neutralization potential strongly depended on the particle size. Using limestone particles of 114" (6.4 mm) or greater, less than 20% of the total neutralization potential was exhausted at the onset of acid conditions. Apparently, the dissolution of limestone became mass transfer limited. Under mass transfer limitations, the rate of pyrite oxidation may exceed the rate of neutralization by buffering minerals. The implications concerning the controls on limestone dissolution were examined using a geochemical predictive model for sulphide mineral oxidation in waste rock. The results have shown that in case of heterogeneous waste rock piles the NP/AP ratio is a reliable indicator for short-tam predictions only. Kinetic data on the depletion rate of the neutralizing minerals and geochemical modelling suggest that waste rock environments with NP/AP ratios as high as 5.0 may turn acidic in the long term.

Jan 1, 2000

By U. S. Geological Survey

In 2025, the estimated total value of nonfuel mineral production in the United States was $112 billion compared with $106 billion in 2024. The estimated value of metal production in 2025 increased by 13 percent to $38.1 billion from a revised total of $33.6 billion in 2024. The total estimated value of industrial minerals production was $73.7 billion, 2 percent more than the revised total of $72.2 billion in 2024 (Table 1). Increases in production of certain nonfuel mineral commodities, along with increases in prices of some industrial minerals contributed to the overall increase in the total value of domestic nonfuel mineral production in 2025. For the industrial minerals sector, the production value of natural aggregates, which comprised approximately 60 percent of the total production value of all industrial minerals, increased by 4 percent even though production volumes decreased by 1 percent in 2025 compared with production in 2024. The largest percentage increases in production value in 2025, in descending order, were for dimension stone, wollastonite, potash, mica and portland cement. The largest percentage decreases, in ascending order, were for high-purity quartz, industrial sand and gravel, lithium carbonate, bromine and boron. For the metal sector, production decreased for several mineral commodities and prices decreased for several metals due to oversupply. Lithium, manganese and nickel had some of the largest percentage decreases in production value.

May 1, 2026

By Robert R. Brandom

The Boss-Bixby deposit is one of several iron deposits that occur in the Precambrian igneous rocks of southeastern Missouri. It differs, however, from all of those deposits by its significant contents of copper, cobalt, and titanium, and its close relationship with a basic igneous intrusion. Ore microscopic study of selected drill core samples has shown that the hypogene ore minerals are magnetite, hematite, chalcopyrite, bornite, covellite, ilmenite, rutile, sphalerite, cobaltian pyrite, carrollite, scheelite, and wolframite. Subsequent partial oxidation has formed martite, pseudobrookite, and anatase. Textural evidence indicates that two stages of iron and iron-titanium oxide formation were followed by the deposition of the copper-iron sulfide minerals and carrollite.

Jan 1, 1985

By Harry Perry

The Bureau of Mines is glad to have this opportunity to discuss its present Coal Research Program and its significance to the industry with a group which has for many years been representative of the coal producing community. We believe we have a dynamic program that will help our vast coal resources to find their proper place in the U. S, economy. The present coal research activities of the Bureau are conducted in three organizational subdivisions: Minerals Research, Mineral Resource Development, and Health and Safety. All investigations are carried out in Bureau research facilities located in different sections of the country, Since its creation by the Organic Act of 1910 and subsequent amendments, the Bureau has worked closely with the coal industry--first by providing assistance in mine safety for anthracite and bituminous coal mining, and since that time, in providing information on conservation, safety, mining, preparation, and utilization.

Jan 1, 1966

By D. D. Harbuck

The U.S. Bureau of Mines investigated germanium and gallium extraction from an ore containing 0.089% Ge and 0.036% Ga. While previous researchers concluded that a reducing agent such as 502 is needed to extract germanium and gallium from such ore, this research showed that high extractions (87% Ge, 97% Ga) were possible using sulfuric acid alone, if the acid concentration were properly controlled. This control was achieved using a two-stage counter-current leach circuit. Microprobe analyses revealed that the non-extracted germanium is in solid solution with quartz, and therefore cannot be leached with 502 or sulfuric acid.

Jan 1, 1991

By T. J. Close

On September 10, 1991, Secretary of the Department of Interior Manuel Lujan deleted the Silver Peak Range North Wilderness Study Area from the list of U.S. Bureau of Land Management lands in Nevada to be considered for wilderness designation. This decision was based in part on the U.S. Bureau of Mines mineral investigation of the wilderness study area which found that it has indications of precious metals resources. The following is a summary of the results of that mineral investigation. The study area lies between the Silver Peak and Dyer mining districts of west-central Nevada. The Silver Peak mining district, to the east, has a long mining history dating back to 1907 when precious-metals-bearing veins were discovered. The major producer in the Silver Peak district was Sunshine Mining Company's Sixteen-to-One silver mine. During the Bureau's study the Sixteen-to-One mine was operating; it has since been idled due to low silver prices. Precious metals-bearing veins were discovered in the Dyer district, to the west of the study area, in the 1860's. Mineral activity in Dyer district consisted mainly of prospecting. The Silver Peak study area itself has no mining history and contains only a few mining claims, but the Bureau examined 13 mineralized sites, most previously unknown and unclaimed. These sites are along two zones that cross the study area from the Silver Peak to the Dyer mining district. The two zones transect a volcanic center of fractured and altered rocks that contain epithermal veins of quartz, calcite, and jasperoid with gold, silver, and base metals. At the surface these veins are poorly defined and poorly mineralized. The more than forty veins examined in the study area are as thick as 17 feet and as long as 1,000 feet. Samples from surface exposures of these veins contained as much as 0.02 ounce per ton gold, 2.1 ounces per ton silver, 1.0 percent copper, 2.6 percent lead, and 0.4 percent zinc. Analyses of the Bureau data disclosed no vein large enough or of high enough grade to be classified a mineral resource. However, most do have indications of silver-and gold-bearing resources at depth. Subsurface exploration had to be done on the vein at the Sixteen-to-One mine to outline reserves (a vein averaging about 22 feet thick and containing 6-to 7-ounces per ton silver); the same is true of veins in the Silver Peak Range North Wilderness Study Area.

Jan 1, 1993

By H. Maleki

Roof falls continue to affect productivity and safety in U.S. coal mines in spite of significant increases in support utilization in recent decades. To minimize roof stability problems while controlling support effectiveness, the U.S. Bureau of Mines is conducting research on support and ground monitoring techniques. Practical implementation of this research is presented in this paper. Instruments to monitor rock mass deformation, support loads, and microseismic emissions have traditionally been used to assess roof stability. Controlled-source seismic surveys are being used as well. In this paper, measurement techniques are reviewed, and the effectiveness of deformation measurements is demonstrated. This is achieved by an analysis of deformation history from four case studies in room-and-pillar retreat mines. In spite of differences in geologic, geometric, and support conditions in these mines, roof behavior is shown to have been similar prior to failure. The rate of roof movement is suggested as a reliable indicator of roof stability.

Jan 1, 1993

By Scott G. Britton

Traditionally, water removal has taken a backseat to many other coal mining functions. However, it is a vital part of the total mine support system. In many US coal mines, more tons of water are removed each year than tons of coal. An excellent discussion of general drainage characteristics can be found in Chapter 8 of Elements of Practical Coal Mining, published by SME-AIME. This chapter is organized into three major sections. These are: designing effective drainage systems; constructing the main mine pumping station (static system); and constructing a portable pumping station (dynamic system). Each topic presents a separate discussion of the elements a construction foreman or engineer should consider for effective installation and operation of the mine drainage system. In addition, a list of pumping equipment manufacturers is available to interested persons and follows these sections.

Jan 1, 1983

By Wern-ping N. Chen

Pressure tunnel includes water-supply tunnels and tunnels for hydroelectrical power plants. Their design principles are different from those of water/wastewater/conveyance and transportation tunnels. Though theoretical pressure tunnel design guidelines exist, a comprehensive guide to summarize these guidelines to facilitate the planning and design of a pressure tunnel program is lacking. The purpose of this paper is to fulfill this need. It first provides key pressure tunnel design concepts in hard rock environment; then, it illustrates associated final lining design principles, including the design of un-reinforced concrete lining, steel lining, and reinforced concrete lining. Design diagrams and a flowchart for the reinforced concrete lining design are provided.

Dec 1, 2022

By Paul C. Schmall, John F. Donohoe, Arthur B. Corwin

In the aftermath of the September 11th attack on the World Trade Center, groundwater control was of immediate concern. Water in?ow from the adjacent Hudson River through the compromised slurry wall ‘bathtub’ surrounding the site, ruptured water and sewer mains, and saturation from fire hoses all contributed to an already critical situation, further hampering the recovery and rehabilitation effort. An extensive pumping and deep well installation program was initiated, focused on reducing the hydrostatic loading to the severely damaged perimeter slurry wall.

Jan 1, 2003

By A. I. Kogut

Impurity minerals in fluorspar ores and concentrates from a deposit in Southern Africa have been studied by reflected light, transmitted light, and cathodoluminescence microscopy. The principal impurities are quartz, calcite, aegirine, apatite, ankerite, magnetite, goethite, and synchysite [Ca(La,Ce,Nd)(CO3)2F]. Cathodoluminescence microscopy was found to be very useful in studying the character of the fluorite and especially for recognizing the presence of apatite and calcite impurities. Fluorite exhibits blue, calcite shows yellow, and apatite has white, light purple, and pink cathodoluminescence. The cathodoluminescent character of apatite varies with its geological environment and position in the orebody. The results of this microscopic study show that phosphorus present in fluorite concentrates occurs principally in binary locked apatite-fluorite particles. Successive fluorite cleaner concentrates contain progressively smaller amounts of locked apatite-fluorite particles. Free apatite has been effectively partitioned to the final tailings.

Jan 1, 1995

By Y. J. Wang

The Hardy Cross iterative method is the most popular technique for solving a ventilation network problem with natural air splitting. This method traditionally solves each mesh equation by an approximation during each iteration. Thus, it is interesting from both a theoretical and a computational viewpoint to be able to solve for an exact solution to the mesh equation. Presented in this paper is an algorithm for computing the exact solution to the mesh equation with a variable fan pressure. The algorithm uses signum functions for air quantities to generate an alternative mesh equation in the form of a quadratic equation that has two solutions defined by the well-known quadratic formula. The condition that the derivatives of the alternative and the original equations must be the same provides a basis for the correct choice between the solutions.

Jan 1, 1998

By J. LeRoy Peterson

This paper presents some of the theoretical aspects as well as some results of actual plant operation of the Ty-Hukki Classifier. Dual classification steps within a unit vessel are achieved by controlled separation of the sand product under turbulant flow conditions, followed by further classification under strictly laminar flow conditions. Plant operation has shown some of the benefits of the superior sharpness of classification to be reduction of circulating load in grinding circuits, prevention of overgrinding, increase in mill feed rate and consequent reduction in cost per ton of ore.

Jan 1, 1966

By Lee A. Goetz

Cost control is a lot like motherhood - everyone proclaims its need and its worthiness, but is it really appreciated and used to successfully complete a project on time and within budget? Good Cost Control is a yardstick - requiring fixed definition but this does not mean rigidity for the project. It provides the means for telling: 1. Where you are going 2. When you will complete and 3. What it will finally cost. Cost Control does not fix the price of dreams nor the cost of projects loosely defined. It does not control costs in itself but provides the tools whereby engineering decisions can be made which will ultimately affect the project cost It does not even guarantee that a project will be completed within the original funds - but only, if this reflects management desires.

Jan 1, 1970

By S. Chander

The mechanism of oxidation of sulfur in pyrite is a function of the rate and driving force for oxidation. New evidence is presented in this article to show that at moderate potentials, a sulfur-rich hydrophobic layer is formed. Under ordinary conditions, the sulfur layer is covered with a layer of iron oxides, hydroxides, sulfate or oxy-sulfide ions. Under these conditions, pyrite is hydrophilic. In the presence of iron-chelating agents or iron sequestering ions, iron layer might not form. Under these conditions, sulfur-layer is exposed and pyritic might become hydrophobic. Stronger oxidizing conditions decompose the sulfur-layer, thereby making the surface hydrophilic.

Jan 1, 1992

By Ming-yi Zhang, Zhong-nian Yang, Xiao-ming Guan, Quan-wei Liu

"In slurry balanced shield tunneling, how to ensure the safety of construction and to reduce the influence on the environment has arisen wide attention of scholars both at home and abroad. But now it is still in the stage of experience as to the instability mechanism of the slurry shield tunneling excavation and its stability analysis. Based on the large-diameter model tests and FLAC 3D, the effect of the different waterhead (non-water, 0.9m and 1.1m) on stability of excavation face of slurry balanced shield is investigated, and the stability mechanics is proposed. The results show that: waterhead heights play an important role on excavation face instability features of slurry balanced shield in sandy stratum, Regarding the different waterhead heights, the development mode of the excavation face instability features can be divided into non-water mode, lower-waterhead mode and higher-waterhead mode; soil arching is existed in the process of excavation face instability, the settlement of ground lags behind excavation face failure, the soil arching will block or eliminate the effects of ground settlement; excess pore water pressure need to be considered besides earth pressure and hydrostatic pressure when the supporting force is calculated. INTRODUCTION With the development of the society, for the cities all over the world, the exploitation of underground space has become an important measure to solve the problems about population, resources and environment and an important way to heal the city syndrome and implement the sustainable development strategy of city. Constructing shield tunnel with large diameter is the major trend for development of tunnel construction (Yin, 1999). Instability of excavation face caused by relief of shield soil stress is still one problem that needs to be solved (Xiang, 2001). How to reduce the effects of construction on surrounding environment? How to accurately determine the instability of shield excavation face and to effectively and reasonably select the supporting force? These are the crucial problems which need to be solved during shield construction."

Jan 1, 2016

By L. A. Rapoport

This paper outlines the methodology and results pertaining to the simulation of the U.S. coal industry in the context of an integrated, time-dynamic model of Long-Range Energy Developments and Supplies (LORENDAS). By way of background we will present first an overview of the overall LORENDAS model structure. We will, then, outline the characteristics of the formulation and data used for the representation of the U.S. coal industry. Finally, a series of model results will be reviewed, with particular emphasis on the long term projections of coal production and distribution under different basic economic and/or political scenarios.

Jan 1, 1977

By R. Svensson

Mill linings play an important role in all comminution processes with tumbling mills. The selection of the lining profile and the lining material has a great impact on over-all grinding cost and mill throughput. The cost of the lining itself is minor in comparison with media cost, energy cost and the value of the material produced in the mill. The total scope must be considered when mill linings are selected. This paper presents case stories and explains the technology behind: -different lining profiles in rubber and steel -OREBED magnetic lining -Steel-cap rubber lining

Jan 1, 1994