Search Documents

By R. M. Damodaran

The flotation performance of Florida phosphate rock was evaluated in terms of the mixing behavior of reagents with particulates during anionic conditioning of phosphate slurries. The various conditioning variables that influence mixing, namely, solids loading, agitation speed and the conditioning time were investigated to determine their effect on reagent coating on the particles. The phosphate recovery was used to monitor the conditioning efficiency. The mixing characteristics of the phosphate feed were evaluated in terms of the ratio of the mixing power P, to the minimum power Pm' required to keep the slurry in suspension. It was found that mixing conditions govern the conditioning time required to obtain high recovery. Reagentization was slower at lower P /P m ratios. At higher P /P m ratios, the flotation recovery was optimized and the agitation speed was found to have no significant effect on it. Optimum mixing conditions were obtained for a 74 wt% slurry at an agitation speed of 450 (47 rad/s) rpm. Under the optimum conditions of mixing, recovery was improved at low collector dosages and short conditioning times.

Jan 1, 1995

By S. Middlemiss

The Indentation Fracture technique is being developed as a tool for use in comminution and mineral liberation analysis. Fracture toughness measurements for a number of mineralogical materials were made and comparisons were drawn between these and properties measured with the Ultrafast Load Cell drop weight apparatus. The technique has also been used as a probe to quantify differences in fracture properties at different areas in the microstructure of a material. In both a Utah limestone and a South African quartzite, material near a grain boundary fractures very differently to that in the bulk. Ongoing work is ultimately aimed at producing a comprehensive fracture model for a multi-mineral system based on its micro-fracture characteristics.

Jan 1, 1994

By K. Hanumantha Rao, K. S. E. Forssberg, F. Su

The influence of reagents dosage, pH, temperature, and particle size on the kinetics of apatite flotation response from magnetite has been investigated. The first-order models characterizing rectangular distribution and fast and slow distributions (F-S model) of floatabilities gave an excellent fit to the results of apatite flotation when compared to other models. However, the latter model is found to be better than the former in the goodness of fit and also in the description of flotation performance. The kinetic parameters in the F-S model are estimated by using a nonlinear least squares fitting program. The ratio of fast and slow rate constants is observed to be an important parameter for identifying the optimum levels of the variables and to outline the selectivity between apatite and magnetite. The influence of collector dosage is realized from the model parameters by relating it to the fraction of slow- floating particles. An attempt has been made to describe the apatite flotation behavior with the determined model parameters.

Jan 1, 1999

By H. Cho

There is an indication that high-pressure roller milling promotes selective liberation due to preferential breakage along the mineral boundaries. A study was undertaken to compare the degree of liberation obtained by high-pressure roller milling with that of conventional ball milling. Coals with different HGI's were ground in a high-pressure roller mill and a ball mill to produce products with similar size distributions. The products were then subjected to float-sink separations to determine the degree of liberation. Also, the relative cleanabilities were compared by separating the ground products by froth flotation. The results from this study are presented in the paper.

Jan 1, 1994

By Keith S. Olsen

Any discussion of barite mining is virtually impossible without considering, almost in the same breath, the many other variables, such as beneficiation, transportation, infrastructure and location that impact the economics of a particular barite orebody. My comments will be limited to just the mining aspects of barite orebodies and these observations must be considered in proper context with all other parameters affecting exploitation of a barite property prior to final decision on economic feasibility. In many instances low-cost mining situations are more than offset by high-cost beneficiation requirements. Likewise, there are cases of relatively high-cost mining associated with no or low-cost beneficiation requirements thus permitting economic exploitation. Barite orebodies and occurrences are almost as varied as the number of occurrences. As in most mining situations, the design of a mine plan and implementation of a proper exploitation program must be approached on a case by case basis. Proper and sufficient geologic control of a barite orebody must precede the development of a mine plan. Generally speaking, barite orebodies can and, at many times, do "strange" things; pinch with depth; almost never increase in size with depth, overturn, fault-off, change grade, etc. Due to the extreme variable nature of most barite orebodies, a mine plan and its implementation must be as flexible as possible. The ability to quickly adapt to variable conditions will greatly enhance the economics within a particular barite mining environment.

Jan 1, 1980

By T. Tamagawa

A gaseous chlorination process for hydrometallurgical treatment of a chalcopyrite concentrate was investigated. The overall process is visualized to consist of low temperature chlorination-selective oxidation, followed by aqueous chloride leaching and SX-EW for producing electrolytic copper elemental sulfur and ferric oxide. In this article, the chlorination phase of the processes is described. Initially, the chlorination behavior of chalcopyrite-concentrate micro-pellets was investigated using a small batch-type fluidized bed reactor. The optimum conditions thereby established was used in continuous chlorination tests. The chlorinated products thus prepared were used in the selective oxidation phase of the investigation.

Jan 1, 1999

By J. Fuller, L. Marsden

Windborne dust from alkaline salt flats and mining-related tailings ponds is especially prone to threaten applicable ambient air quality standards. Sodium carbonate crystals, typically present, weather to an exceedingly fine, non-cohesive dust, causing air quality problems for miles downwind. Recently developed specialized polymers react with alkaline dust to form sturdy, wind-resistant crusts with good longevity. An on-going demonstration project at a major trona facility has developed techniques for cost-effective application of these polymers over large areas of soft tailings or sediments in a wide variety of situations. Recently treated areas on the order of 80 acres show effective suppression of dust.

Jan 1, 2004

The introduction of nitro-carbo-nitrate (NCN) blasting agents has been one of the most significant innovations in the explosive industry in the last twenty years. The most commonly used blasting agent is a rather narrowly proportioned mixture by weight of 94% ammonium nitrate (AN) and 6% No. 2 diesel fuel oil (FO) that is generally designated as ANFO. Other formulations have been developed but none of these have been as extensively used as ANFO. The relative safety of the nitro-carbo-nitrate (NCN) blasting agents almost immediately suggested bulk loading techniques to obtain economies in materials handling. The first attempt at bulk handling was to pneumatically load boreholes with ANFO. When the initial experiments were made in 1957, it was apparent that there were three problem areas which needed study to minimize potential hazards. These were: 1. Static Electricity 2. Fumes 3. Safe Handling Procedures Since those early days, considerable work has been performed in evaluating these problem areas and in arriving at procedures and recommendations that would provide the required safety. Despite the relative insensitivity of ANFO type products, all normal practices for the safe handling of explosives should be obselved. Smoking should not be tolerated in the vicinity of blasting agents and misfires should be handled in the same manner as a misfire with a dynamite charge. The purpose of this Technical Report is to discuss the problems of static electricity and fumes and the solutions that have been developed. Safe handling procedures have been discussed by the Bureau of Mines and are specified by various state and local regulations. Since regulations vary from state to state, the local, applicable regulations must be followed within the area of their jurisdiction. General information is contained in a U. S. Bureau of Mines report, IC 8179, "Safety Recommendations for Sensitized Ammonium Nitrate Blasting Agents" (1963).

Jan 1, 1973

By R. L. Godfrey

The Custom Coals advanced coal cleaning plant will be designed with a unique blending of existing and new processes to produce two types of compliance coals: Carefree Coal? and Self-Scrubbing Coal?. Carefree Coal will be produced by cleaning the coal in a proprietary dense media cyclone circuit utilizing fine magnetite to remove up to 90 percent of the pyritic sulfur and correspondingly greatly reduce the ash. While may utilities can achieve full S02 reduction compliance with Carefree Coal, others face higher sulfur reduction requirements due to the higher sulfur content of their existing fuel supplies. For these circumstances, a patented Self-Scrubbing Coal will be produced by taking Carefree Coal and pelletizing limestone-based additives with the finest fraction of the clean coal. These technologies will enable over 150 billion tons of non-compliance U.S. coal reserves to meet compliance requirements.

Jan 1, 1995

By Christopher Laughton, Michael P. Bruen

At Fermilab, a 4000-ft long underground complex has recently been constructed for a high-energy physics experiment. The complex is sited up to 350 ft, below grade principally in bedrock. The rock excavations were mined by TBM and drill and blast methods and supported by a combination of rock bolts, dowels and shotcrete. Water control was achieved using a combination of pre- and post-excavation grouting, drainage systems, drip shielding and air desiccation measures.

Jan 1, 2003

By J. A. Herbst, L. B. Hales, R. Zaragoza

INTRODUCTION The Control Problem The need for automatic control in flotation plants stems from frequent and randomly occurring disturbances to the feed slurry. Typical disturbances occur in the solids feedrate, the slurry percent sol ids, and the mineralogy and flotability of the gangue and valuable minerals. In plants where semi -autogenous grinding mills (SAG) are used, feedrate changes are very large and changes in feed percent solids of 1m or more are common. Mineralogy changes between valuable minerals are common, as are changes in the host gangue rock. As these changes occur, the operator can attempt to compensate for them by making adjustments to the flotation cell levels, the dosage rates of the collectors and frothers, the pH, and in some cases the aeration rate of the cells. This problem is sometimes complicated by the fact that different sections of the flotation plant will be processing different ore types at the same time. Potential Savings with Control Flotation control brings about savings or plant improvements in two areas; the first is in improved metallurgy and the second is in reagent savings. Improved metallurgy includes increases in the average plant recovery and achieves target concentrate grade level s more consistently. Average recovery increases between 1.0 and 5.0 percentage points have been widely reported (Paakkinen, 1979; Sutherland, 1984). Reagent savings of up to 40 percent have also been reported (Hales, 1985). VARIABLES OF IMPORTANCE Control led, Manipulated, and Disturbance Variables The initial step in the analysis of the flotation control problem is identification of important variables which can affect the efficiency of separation. The efficiency of separation is represented by a group of controlled variables which can quantify the performance of a flotation circuit. This group includes variables such as grade, recovery, tonnage through- put, and circulating loads. The efficiency of separation of a flotation circuit may generally be defined by a grade recovery map, where each point on this map re- presents a set of operating conditions (see Figure 1). However, the combination of operating conditions must be set to operate close to the economic optimum. The group of operating variables which are changed in order to achieve desired circuit performance are called manipulated variables and can be classified into two

Jan 1, 1986

By J. C. Agarwal

A significant portion of the, coal mined by U. S. Steel is beneficiated to upgrade the quality of the resultant coke to meet blast-furnace requirements. Primarily because of degradation from modern mechanized mining methods, a considerable quantity of the coal to be beneficiated is in the 1/4-inch by 100-mesh size range. In the cleaning plants, this coal is usually cleaned on concentrating tables and then mechanically dewatered in solid-bowl centrifuges to 9 to 14 percent water. At some plants, to further decrease the amount of water shipped with coal, and to improve the coking characteristics of the coal at its destination, mechanical dewatering is followed by thermal drying. At U. S. Steel's-Alpheus preparation plant at Gary, West Virginia, approximately 50 percent of the total coal produced is in this fine size range, and two fluidized-bed dryers are used for the thermal drying step. The two fluidized-bed dryers are 14 feet in diameter and were designed by the Dorr-Oliver Company. Although the original design called for a rate of drying equivalent to 37 tons, of moisture per hour, presently they are removing twice that amount. This paper describes, the major problems encountered' in operating these dryers at the present, high capacities and how they were overcome.

Jan 1, 1963

By F. E. Kottlowski

Widespread high-calcium limestones in New Mexico region are low -in magnesium, but some units include shale interbeds deleterious for sulfur removal usage. Thick limestones in Mississippian Escabrosa, Lake Valley, and Leadville, Pennsylvanian Madera and Hermosa, Pennsylvanian-Permian Horquilla, Permian Hueco and Capitan, Cretaceous U-Bar, and some Cenozoic travertines are high-calcium units. Significant outcrops are in mountains of southwestern, south-central, central, southeastern and north-central New Mexico, southeastern Arizona, southwestern Colorado, and northwestern Chihuahua. Coal-fired powerplants are mainly in northwestern New Mexico and eastern Arizona, thus transport is mainly by railroad.

Jan 1, 1994

By E. Alan Haley

Accurate and economic control of line and grade on long tunnels, large structures, excavations and waterways, has been a problem to surveyors and engineers for decades. The conventional method of surveying, incorporating a level, transit, and a number of surveying technicians, has proven, in the past, to be a very expensive and time-consuming operation. Alignment with a laser has solved most of the problem. Figure 1. With the advent of the Perkin-Elmer Model 5620 Construction Laser, use of laser light is now both dependable and economically feasible for unlimited applications in modern construction and surveying. The laser projects a continuous, narrow red beam of brilliant light, providing a constant alignment reference, and will not interfere with operations.

Jan 1, 1968

By K. L. Johnson

Networks of monitoring wells were established prior to mining at four longwall mine sites in the Appalachians to monitor the effect of mining on water levels, water quality and well yield. Two of the sites were located in stream valleys and the other two sites were located on hilltops. The depth to the mined seam ranged from 500-850 feet with the deeper cover being associated with the hilltop sites. Maximum declines in groundwater levels during and after mining were an order of magnitude less in the stream valley aquifers than in the hilltop aquifers. However, water levels in hilltop wells located outside the area immediately above the panel were unaffected. Water quality changes in wells as a result of longwall mining were negligible at all four sites. Increases in aquifer transmissivity and well yield were much more pronounced in the stream valley aquifers than in the hilltop aquifers. The significantly larger recharge area for the stream valley aquifers than that for the hilltop aquifers may partially account for the differing responses of these two classes of aquifers to longwall mining. These observations appear to be consistent with the stress-relief fracture model for Appalachian Plateau groundwater hydrology proposed by Wyrick and Borchers in 1981.

Jan 1, 1986

By Michael Bayerl

The HILTI OneStep rockbolt was implemented for roadway development in German deep coal mines in 2004. The development by HILTI Company is based on a technical joint venture with RAG Deutsche Steinkohle AG. The technical development of a One-Step bolting system was required for weak strata conditions at the roadway development face. Standard resin bolting has reached the limit of performance when boreholes are squeezed and cannot be filled with capsules. In some cases the heading face is brittle and requires additional support for installation of the bolts and a person working immediately next to the borehole. The Hilti One-Step system allows automated and safe processing at the heading front and provides the key technique to avoid these problems.

Jan 1, 2009

By S. K. Singh

To meet increasing demand of coal, underground mining is largely being replaced by the exploitation at deeper horizons and with greater complexities. The exploitation-proposition may be below not-to-be-disturbed surface properties or below water-bodies, posing a constant threat of inundation. Also, the mounting pressures to limit the adverse impacts on the environment bring the extraction-undertaking to face more challenges. An understanding of subsidence-mechanism and a rational quantification of subsidence parameters is a requisite herein. This paper presents such pragmatic quantification, validated at mine-sites in India. In comparison, better productivity, conservation and safety is ensured in this approach.

Jan 1, 1999

By M. Canty

Results are presented that were gathered during pilot-and field-scale testing of an innovative technology, sulfate-reducing bacteria (SRB), designed to treat and control acid mine drainage (AMD). The project was performed under the Mine Waste Technology Program (MWTP), which is funded by the U.S. Environmental Protection Agency (EPA) and jointly administered by the EPA and the U.S. Department of Energy through an Interagency Agreement. The MWTP is implemented by MSE, Technology Applications, Inc., located in Butte, Montana. Sulfate-reducing bacteria, a common group of anaerobic bacteria, produce hydrogen sulfide and bicarbonate when supplied with sources of carbon and sulfate. Hydrogen sulfide reacts with metal ions in AMD, precipitating them as metal sulfides; the bicarbonate serves to help neutralized the drainage. Pilot-scale testing was performed within eight packed-bed reactors at a temperature representative of a field application of this technology in a northern climate, nominally 8°C. The reactors, packed with an organic substrate, were operated continuously in upflow configurations receiving AMD at a flow rate corresponding to a 5-day retention time over a test duration of 60 days. During this time, numerous physical and chemical parameters were monitored. Pilot-scale metal removal efficiencies reached 99% for zinc, 99% for aluminum, 96% for manganese, 98% for cadmium, and 96% for copper. Iron and arsenic removal was not as effective as the aforementioned metals, which was largely attributed to the high levels of iron and arsenic contaminating the organic substrate. Evidence existed that both adsorption and sulfate reduction were occurring within the reactors.

Jan 1, 1998

By George M. Meisel

This paper is devoted to a discussion of the factors governing design of concentrators for large grinding circuits. Emphasis is placed on the manner in which use of ever larger grinding mills has affected the size of grinding bays, service cranes, gear reducers and electric motors, and the selection of ancillary equipment for cushioning of the starting load of large mills. Information is presented on the effect of using large grinding mills on the capital and operating costs of concentrators, e. g. : (Fig. 1) ? Benefits in lower cost of mills, drives and materials handling equipment, plant space, power, grinding media, operating labor and maintenance, and in ease of instrumentation and automation. ? Penalties in distribution of materials from the grinding mills to multiple lines of equipment which have not been developed to commensurately large sizes, and higher cost of ancillary equipment.

Jan 1, 1968

By C. I. Everson

The Elkhorn mining district is located 35 kilometers southeast of Helena, Montana, on the southeast edge of the Boulder Batholith. Geologically the district consists of a folded sequence of Paleozoic limestones and shales which have been thermally metamorphosed and altered by monzonite to diorite intrusives related to the Cretaceous Boulder Batholith. For the most part, the skarns are associated with metasomatic: replacement of calc-silicate hornfels, diorite and marble by iron rich, dark green pyroxene, garnet, sulfides, the district contains excess of 30,000 Kg.

Jan 1, 1992