Search Documents

By Robert Blair, David L. Fey, Stanley E. Church

Determination of the pre-mining geochemical baseline in bed sediments in watersheds impacted by historical mining activity is important in establishing watershed restoration goals. We have developed methods to solve this problem in the Animas River watershed, southwestern Colorado, using geomorphologic mapping to identify terraces that contain pre-mining sediments. Following a systematic evaluation of possible sites, we collected samples of pre-mining sediments in gravel deposits from 21 sites throughout the watershed. Geochemical analysis of individual layers has produced a chemical stratigraphy that can be tied to the historical record through geochronological and dendochronological studies. Analysis of geochemical data, when coupled with the historical record, clearly shows that there has been a major impact on the geochemistry in bed sediments in the active stream channel by past mining activities. Historical mining has resulted in a substantial increase in metals in the very fine sand to clay-sized component of the bed sediment of the upper Animas River, and Cement and Mineral Creeks, which are the major tributaries of the Animas River. Enrichment factors for metals in modem bed sediments, relative to the pre-mining sediments, range from 1 to 6 for arsenic, 1 to more than 10 for cadmium, 1 to about 15 for copper, 1 to more than 25 for lead, 1 to more than 10 for silver, and 1.6 to more than 12 for zinc. The pre-mining bed sediment geochemical baseline is high relative to average crustal abundance values of many metals. The Animas River watershed above Silverton, Colorado would be readily identified as a highly mineralized area suitable for mineral exploration if it were not disturbed by mining.

Jan 1, 2000

Integrated mining information and process control systems can reduce information delays, enhance decision making and improve the responsiveness of mining operations to, for example, variations in market conditions, mineral grades and ground conditions. This paper examines developments in the areas of: monitoring, data analysis and diagnosis,' communications systems; integrated mining support system;, and process and machine control. It concludes that the development of a comprehensive information technology plan is fundamental to the phased implementation of these technologies. In addition, hardware and software standards and concurrent digital design and simulation practices in selected manufacturing industries are examined and concluded to have relevance to the mining industry. Integrated information and process control systems will lead to emergence of the "digital mine". Such advances in mining information infrastructure as well as mining equipment will enable mining operations to shift from mass production methods to leaner production techniques. "Lean mining" aims to enhance and accelerate cash flow over the life of a mine by focusing on reduction of' throughput times; stockpiles for volume and quality control; and wastage and rework.

Jan 1, 1995

By M. C. Manderson

Phosphate rock is a naturally occurring mineral which, in upgraded form, is important to both agriculture and industry. Phosphate rock normally must be upgraded before it can be assimilated and used. Most of this upgrading is now carried out by chemical means, largely through the reaction of a strong inorganic acid (primarily sulfuric acid) with the phosphate rock to remove major impurities and to produce soluble phosphate. A less important but yet still commercially significant conversion method involves the thermal reduction of phosphate rock at high temperature in an electric furnace to produce elemental phosphorus. The elemental phosphorus is then converted to usable end products. This conversion route is a more costly method than the chemical route, but it has the advantage of being able to produce chemically pure phosphorus derivatives. On the other hand, the use of phosphate rock for agricultural application-primarily for use as a plant nutrient ingredient for fertilizer -does not require the same level of purity. As a consequence, the chemical method of phosphate rock upgrading is the predominant technique for producing phosphatic fertilizers.

Jan 1, 1977

By V. O. Tenorio, J. Puell

"Dump design is critical to effective mine planning in large scale open pit mines. Capital and haulage costs are considerable from early stages and through the life-of-mine as these dumps gradually become immense structures. Delivered mining rates, as well as certain spatial and physical constraints, provide a set of parameters of mathematical and economic relationship that creates opportunities for modeling and thus facilitates the measuring and optimization of ultimate dump design by using programming and empirical techniques while achieving economic objectives. This paper presents a methodology to optimize the ultimate dump design by minimizing its total dumping costs. The methodology consists of the formulation of a generalized model based on the relationship of the main dump parameters, followed by the use of linear programming to find the solution that minimizes the haulage total cost, and finally through a series of iterations, modifies the preliminary solution by projecting it to the topography and creating the ultimate dump design. A case study applied to a waste dump exemplifies this methodology. INTRODUCTION Open pit mine operations move large amounts of material on a daily basis from the shovel faces to the appropriate destination points. Hustrulid et al. identified three major destination places where the material receives downstream treatment after its delivery: mill processing, leaching dumps, and waste rock dumps [1]. The corresponding destination is given by a cut-off grade criteria, ore type, and the possibility of obtaining the maximum metal recovery. Dump leaching technologies have developed substantially since 1975 [2], and have enabled mining facilities to beneficiate low grade sulfide and oxide ores. As a consequence, the number of active dumps have increased since then and the entire mine configuration, which is limited in itself, has changed. The proper location, design, and construction of a mine dump must serve the safety, environmental and economic goals of the long-range mine plans. Therefore, an optimized use of the available surface area in the mine is highly desired."

Jan 1, 2018

By Richard P. Killmeyer

In 1985 the Pittsburgh Energy Technology Center (PETC) of the U.S. Department of Energy (DOE) conducted a study to evaluate the emerging selective agglomeration processes (Killmeyer, 1985). This paper covers a recent similar study evaluating an associated technology, the emerging advanced froth flotation processes. This study has goals similar to those of the 1985 study: to evaluate the emerging froth flotation technologies collectively and determine how far they have progressed in their ability to clean ultrafine coal, and to assess the differences among the participants. The major concern again in this study was not the level of development, nor the economics of each individual process but only the current technical performance.

Jan 1, 1989

By K. F. Unrug

Martin County Coal Corporation is located in Martin County, Kentucky in the Appalachian coal fields, near the West Virginia border. The total leasehold covers more than 33 000 acres. Total annual production at Martin County Coal Corporation is currently 2,500,000 tons, but in certain years exceeded 3,000,000 tons. Approximately 45 percent of the annual production comes from two surface mines. The balance is produced from five underground mines. Martin County Coal Corporation's work schedule consists of 240 days/year, two nine-hours shifts/day.

Jan 1, 1991

INTRODUCTION Automatic controls are devices that assist operators by performing routine tasks faster and better than they could alone. Great strides have keen taken in the development of new processes and bigger machines to improve productivity, but these developments created the need for increased protection of machinery and labor. The new production-line techniques, or continuous processes developed, resulted in routine and, frequently, demoralizing jobs. The human race is not constituted mentally to perform routine operations. Devices were needed also to gather information automatically and perform routine functions. High-capacity plants incorporating large equipment

Jan 1, 1985

By Phillip O. Tyree, R. A. Metz, Joseph W. Mussey

Bio-epigenetic sulphur deposits occur in Pecos, Reeves and Culberson counties of far West Texas. Sulfate reducing bacteria, utilizing hydrocarbons as energy, transformed gypsum into replacement limestone and hydrogen sulfide. Hydrogen sulfide, retained in the pores of the replacement limestone, was subsequently oxidized by highly oxygenated groundwaters, and native sulphur precipitated. West Texas sulphur was first recognized at surface exposures by William P. Blake, a geologist attached to the Captain Pope Military/ Scientific Expedition of 1854. Attempts were made in the early 1900's to mine these sulphur vent exposures by a retort method, but the ventures met with little success. In 1967, Duval discovered a large sulphur deposit near some of the old sulphur works in Culberson County. Duval also expanded reserves in a small sulphur deposit in Pecos County. The Frasch process, developed for producing sulphur from Gulf Coast salt domes, proved successful in West Texas type sulphur deposits also. However, modifications of the process were necessary to provide economical and efficient sulphur recovery from the varied ore occurrences. West Texas conditions and logistics require the ultimate in productivity to be competitive in the domestic and foreign sulphur markets. Several companies, in addition to Duval, are producing or have produced sulphur in West Texas. As of June 1, 1984, a total of 29.87 million mt (29.4 million long tons) of sulphur had been produced west of the Pecos River. Duval corporation has produced more than 88 percent of that total.

Jan 1, 1992

By J. D. Miller, Jon J. Kellar

Researchers in flotation chemistry have long sought to describe collector adsorption phenomena in greater detail including kinetics, orientation and interactions between adsorbed species. Now a quantitative description can be made in-situ using FTIR internal reflection spectroscopy. Details of the adsorption process at the surface of mineral crystals, machined into internal reflection elements, can be described from first principles, provided the refractive indices, incident angle, and wavelength of light are known. Collector orientation can be established based on spectral characteristics of plane polarized and perpendicular polarized light. Examples of the use of in-situ FTIR internal reflection spectroscopy are given for the sapphire-sodium dodecyl sulfate system and for the fluorite-sodium oleate system. It is expected that quantitative in-situ analysis of collector adsorption reactions by FTIR internal reflection spectro-scopy will continue to grow in importance and will provide an important new dimension in our understanding of flotation chemistry.

Jan 1, 1989

By R. D. Peterson

Autocad has become the standard graphics package for the mining industry as well as the general engineering profession. This paper discusses the evolution that mine planning has undergone and the trend toward compatibility with Autocad. It discusses the common use of Autocad in mine planning and systems modeling using a program called ICAMPS developed by Ohio Automation. As an example of its usefulness the use of the interactive ventilation network modeling capabilities are discussed specifically and are applied to mine planning at an operating trona mine. The ventilation analysis feature of the ICAMPS software works from Autocad drawing of the as-mined map and the projected mine layout. Using on-screen displays of these maps and the snap-on feature of Autocad, the planner designates nodes in the ventilation network, connects them into branches and selects branch characteristics from a side bar menu. The color coded ventilation network appears with the branch parameters alongside each branch. The software calculates the length of airways, computes the branch resistances where needed, converts the input into the required format and passes this information as input data along to the PENNVEN simulation program written by the Pennsylvania state University. Output is available in graphical as well as report format. The color coded graphs include pressures at the nodes and flow quantities on the branches. Since the networks come from the mine maps, the ventilation schematic displays are to scale and can be plotted separately or superimposed on the mine maps.

Jan 1, 1995

By J. F. T. Agapito

Energy West Mining operates the Deer Creek and Cottonwood/Trail Mountain coal mines in the Wasatch Plateau about 40 km (25 miles) southwest of Price, UT. The Deer Creek Mine extracts the Upper Blind Canyon seam and the Cottonwood/Trail Mountain Mine extracts the Hiawatha seam 12 to 36 m (40 to 120 ft) below. Both seams average about 2.8 m (9 ft) in thickness. Cover depths exceed 550 m (1,800 ft) in a large portion of the unmined reserve. Stability problems at Deer Creek are mostly due to coal bursts caused by high stresses associated with deep cover and sandstone channels. Most of the bursts have occurred in gate pillars and, to a lesser extent, at the longwall face and during development. The introduction of a two-entry gateroad system with 9-m- (30-ft-) wide yield pillars has been a major factor in controlling and minimizing gate pillar [ ] bursts (Agapito et al., 1988). However, some bursting began to occur in the 9-m- (30-ft-) wide pillars as cover depths reached 550 to 610 m (1,800 to 2,000 ft). This was due to more rapid and higher abutment loading in areas with very strong roof and stiff floor.

Jan 1, 1997

By E. T. Tuzcu

Microscale information about single particle fracture can be incorporated into the macroscale model of the whole size reduction process in the mill. The ultrafast load cell (UFLC) device provides a substantial amount of information about fracture characteristics of a particle under impact loading. UFLC captures high-resolution compressive force signals during particle breakage. The measurement of the compressive force at the instant of fracture of the particle allows computation of a number of comminution-related particle properties, as well as the energy absorbed during fracture. In the current study, limestone particles 50 mm in size were fractured to obtain specific fracture energies. Then, based on the experimental data, two models were proposed to quantify the fracture process. The specific fracture energy distribution of the particles in the range of 6 to 50 mm was defined by the well-known Weibull distribution. The other model is a probabilistic fracture model. This model is a link between energy events occurring in a grinding mill and the breakage rates of particles. The impact energy spectra or energy events occurring in a grinding mill can be obtained with a discrete element method (DEM) simulation. One can model the breakage rates of the mill material by combining the energy spectra with the probabilistic fracture model. This novel approach for the modeling of breakage rates via DEM and UFLC is shown here.

Jan 1, 2011

By E. T. Tuzcu

Microscale information about single particle fracture can be incorporated into the macroscale model of the whole size reduction process in the mill. The ultrafast load cell (UFLC) device provides a substantial amount of information about fracture characteristics of a particle under impact loading. UFLC captures high-resolution compressive force signals during particle breakage. The measurement of the compressive force at the instant of fracture of the particle allows computation of a number of comminution-related particle properties, as well as the energy absorbed during fracture. In the current study, limestone particles 50 mm in size were fractured to obtain specific fracture energies. Then, based on the experimental data, two models were proposed to quantify the fracture process. The specific fracture energy distribution of the particles in the range of 6 to 50 mm was defined by the well-known Weibull distribution. The other model is a probabilistic fracture model. This model is a link between energy events occurring in a grinding mill and the breakage rates of particles. The impact energy spectra or energy events occurring in a grinding mill can be obtained with a discrete element method (DEM) simulation. One can model the breakage rates of the mill material by combining the energy spectra with the probabilistic fracture model. This novel approach for the modeling of breakage rates via DEM and UFLC is shown here.

Nov 1, 2011

By Yoginder P. Chugh, M. Silverman

Premining investigations involve the determination of roof, floor, and coal seam characteristics to delineate areas of troublesome ground control prior to development of a mine. Data obtained can be useful in mine design, equipment selection, estimation of face productivity, development of ground control plans and assessing ground control costs, and in conducting feasibility studies and financial analyses. This paper discusses 1) the causative factors associated with ground instability, 2) how useful data can be obtained for these factors during premining investigations, and 3) analysis techniques to delineate probable areas of ground instability.

Jan 1, 1982

By Frank Hagar, George M. L. Robinson

INTRODUCTION Mine waste monitoring and management is essential when the industry is being required to accept the environmental liability for all generated, stored and disposed solid and hazardous waste. Environmental regulations mandate the operator to minimize waste production while requiring the operator to cleanup existing contamination. Since these requirements are being enforced, many operators do not have a clear under- standing, whether their existing operation will or could be required to adopt remedial plans to mitigate off-site contamination impacts. The following methods, using conventional and advanced geostatistical methods, provide a tool to make appropriate assessments whether existing or potential contaminant issues are present. BACKGROUND Generated solid wastes from mining operations are currently exempt from Solid Waste Disposal Act (SWDA) Sub- title C (RCRA), statutes and promulgated regulations, however, compliance with SWDA Subtitle D statutes and regulations is required. In order for the mining operator to be exempt from hazardous waste regulations, the operator must demonstrate that generated waste does not have hazardous waste characteristics. In many instances the operator will be able to use statistical tools and their existing data to determine whether their site could be a potential hazardous waste liability. METHODS The following statistical and geostatistical methods can be used to determine whether existing wastes could be a regulatory concern. The following presents a brief discussion of standard statistical methods and discusses, in greater detail, how advanced geostatistical tools can be used to define potential waste issues. The following will discuss how data can be screened, "Data Filtering and Reporting"; how data can be evaluated using "Conventional Statistics"; followed by a detailed discussion o f "Geostatistical and Estimation Techniques" and "Statistical Modeling". Data Filtering and Reporting Data filtering is the simplest, but potentially the most powerful statistical tool because data can be easily sorted to meet regulatory reporting requirements. Filtering includes unions and intersections of data such as date, maximum and minimum values of one or several variables. Using the data base presented in "Mine Waste Data Base Management Procedures", Robinson and Hagar, 1987, an example of a filter group is presented.

Jan 1, 1987

By R. R. Fernández

The Newmont roasting plant in Carlin, Nevada, commenced operating in December 1994. Over the years, refractory ores and pyrite concentrates from different gold deposits constituted the feed to the facilities. Historical plant performance indicated that the roasting temperature was the main variable affecting the structural characteristics of the calcine, which in turn affected the recovery of gold by cyanidation. Gold recovery as a function of roaster temperature has been closely monitored since October 2000. The original design temperature was 550° C. Lower roaster temperatures of around 500° C resulted in a gold recovery increase of more than six percent. This increase was directly related to an increase of the surface area of the calcine. The implementation of an ?intelligent? process control system helped significantly in achieving steady low roasting temperatures, thus obtaining high gold recoveries of 92 to 93 percent. Under these conditions, several roasting campaigns with high-arsenic-containing ores were conducted, which resulted in a significant decrease in gold recovery. The reduced gold recovery was caused by the loss of surface area (e.g., porosity) of the calcine as the arsenic content of the roaster feed increased.

Jan 1, 2010

By Kevin D. Lofftus

This paper presents a dynamic model for column flotation. The model equations are normalized and the dimensionless groups that are directly responsible in determining the column flotation behavior are identified. The resulting model equations are incorporated for computer simulation. Numerical results from computer simulations are analyzed to gather information about design and operation of column flotation devices.

Jan 1, 1988

By D. A. Norrgran

The recent development of rare earth permanent magnets has revolutionized the field of magnetic separation. The advent of rare earth permanent magnets in the 1980's provided a magnetic energy product an order of magnitude greater than that of conventional ferrite magnets. This has allowed the design of high-intensity magnetic circuits operating energy free and surpassing the strength and effectiveness of electromagnets. New applications and design concepts focused on the mineral and metal processing industries have evolved. This technology also led to the development of various magnetic separators specifically designed for mineral processing applications. Applications which were not previously considered are now being applied to primary mineral upgrading and recycling and secondary recovery.

Jan 1, 1993

By Dirk van Zyl

It can systematically assess if the control and management systems designed for protection of sensitive ecosystems are adequate. The results of the assessment can help to identify key elements in the project that pose higher risks due to uncertainties in design. These assessments can then be used to make recommendations to further manage and reduce risks as the project is developed. QUALITATIVE RISK ASSESSMENT The general principles of a risk assessment are well summarized by Kaplan and Garrick (1981): "In analyzing risk we are attempting to envision how the future will turn out if we undertake a certain course of action (or inaction)." Fundamentally, therefore a risk analysis consists of an answer to the following three questions: What can happen? (i.e. what can go wrong?) How likely is it that that will happen? If it does happen what are the consequences?" Risk assessments can be performed using various levels of sophistication depending on the amount and accuracy of data available. A qualitative risk assessment uses descriptors throughout to express the level of risk. The definitions of the descriptors are presented in terms of the magnitude or concentration of contaminants. The results of a qualitative risk assessment can be used to: a)Document the evaluation and decisionmaking process. Although differences of opinion may exist about the definitions of the descriptors, the process is well-documented; b)Express the relative risk associated with specific activities or design elements; and, c)Select those failure modes or release mechanisms that may result in significant risks. These mechanisms can then be further developed in quantitative risk assessments. A qualitative risk assessment can be performed in a systematic approach using four steps (Van Zyl, 1987): A qualitative environmental risk assessment can be used to describe the risks associated with the development of a new mine and to make an evaluation of the adequacy of its design for environmental protection. The relative magnitude of risk associated with selected failure modes and exposure/consequence scenario assessments is the final result of a qualitative risk assessment. These failure modes are based on site specific areas and components, and mining and construction phases. The four steps of a risk assessment (hazard assessment, exposure assessment, consequence assessment, and risk characterization) are used in the development of a qualitative risk assessment. Relative magnitudes (using a five point scale of negligible to high) for each step, can be quantified in a qualitative risk assessment. Development of the descriptors for the relative magnitudes in each step is a very important part of a qualitative risk assessment. The success of a qualitative risk assessment depends on the adequacy of the information base and the subjective judgements made in each step. The quality of the risk assessment is, therefore, dependent on the experience of the assessors. A mining project in a sensitive coastal environment is presented as an example to demonstrate the application of a qualitative risk assessment. INTRODUCTION Environmental impacts from mining operations have been a significant factor in the last century. This was especially the case prior to the development of a better understanding of environmental processes and the potential impacts of acid rock drainage (ARD), and associated heavy metals, or the uncontrolled disposal of tailings and waste rock (Smith, 1987). Much care has been exercised over the last two decades in designing and operating mines to limit the environmental impacts as far as possible. All new mines are specifically designed with mitigative methods to manage such potential environmental impacts. Attention is directed to ARD impacts, safe disposal of mine waste rock and tailings, transportation and storage of chemicals and fuels, and final reclamation. A qualitative risk assessment can be used to address all project systems and activities that may potentially pose a risk to the environment.

Jan 1, 1992

By S. Chander, A. Briceno

The effect of sample storage in argon and in air on the kinetics of oxidation of pyrite from a coal source was studied using accelerated-weathering tests that were performed in laboratory columns. Prior to the weathering tests, the samples were crushed, ground and stored for various periods of time in either argon or air. The test results showed a dramatic difference in the rate of oxidation of the aged samples. The interpretation of the differences was based on the hypothesis that the aging of pyrite led to the formation of surface coatings that changed with time. "Dry" oxidation produced surface coatings that had properties different from those produced by "wet" oxidation. The significance of these results to pyrite/reagent interactions during flotation and in evaluating the acid-mine-drainage potential of pyritic waste materials is discussed.

Jan 1, 1995