Search Documents

By Michel Grenier, Gopal Kunchur, Stephen Hardcastle

This paper presents the findings of a dust study in a typical fluorspar processing plant. The primary purpose of this study was to identify employees and occupational groups exposed to high dust levels and determine compliance with personnel regulations for regular and extended work shifts. The range of airborne concentration of respirable silica and fluoride compounds in specific areas and on personnel was determined. State of the art dust monitoring equipment and tracer gas techniques were used to measure dust concentration, pinpoint dust sources and map major airflow trends in the mill. Results of the survey indicated silica dust concentrations in excess of permissible limits being produced mainly by crushers at the south end of the building. Tracer gas releases and gas chromatographic analysis further showed that prevailing south to north air currents tended to carry and spread dust produced by the crushing operations throughout the process plant. Airborne concentrations of fluoride compounds measured during the study were always well below the prescribed threshold limit value (TLV) for the contaminant. Recommendations, including a mechanical exhaust ventilation system on crushers and transfer points, scheduled preventive maintenance on existing bar sprays and wearing of personal protective equipment were made which significantly improved the work environment. Further testing conducted after Installation of the dust extraction system revealed significant improvements in most areas of the mill.

Jan 1, 1991

By Henryk Bystron

The underground fire areas are formed as a result of failure of an active fire extinguishing in mines. Such areas bring about a fire hazard for the work safety and for the mining operations. For liquidation of fire areas it is necessary to create conditions under which a possibly small amount of air is flowing to the fire. To achieve this end, isolation methods are used which consist in erection of full stoppings of various types, sealing practically the fire areas. These methods usually fail in oases when the coal seam is thick and the fire area is situated between the intake shaft and the outtake shaft in which a high-pressure fan is in operation. In such oases ventilation methods based on the balance of aerodynamic potentials in fire areas are to be used. For a very long time the isolation and ventilation methods have been developed in the world mining, No sooner than since 1980 the aerodynamic potential has been used in ventilation methods [1,2,6]. So far, the aerodynamic potential was called in different ways and was determined by different formulae which gave its numerical values more or less approximative. Nevertheless, even in situations featuring by a lack of sufficient theoretical bases of the aerodynamic potential the ventilation methods brought considerable profits in the field of safety in mines and of economics in mine ventilation [1-6,9,10]. The increase in the depth of underground mines and their equipment with expensive machines (apparatus) brought about that the Central Mining Institute at Katowice undertook research works which are crowned by the theory of the aerodynamic potential in mine ventilation networks [7]. The use of this theory in the mentioned ventilation methods will increase their effectiveness. Since the theory will be published in the III rd quarter of this year, we cite in the present paper the formulae and relations associated with this theory which are indispensable to present the balance of aerodynamic potentials in the fire areas in their control by ventilation methods.

Jan 1, 1980

By D. J. Cook, R. H. Fan, D. R. Maneval, Y-H. Shen

In this study, two placer mine processing plant effluent waters of significantly different characteristics were tested to determine the applicability of polymers along with other techniques to achieve reduced levels of turbidity. The waters from a Gilmore Creek mine and a Crooked Creek mine were characterized both as to their chemical and physical properties. The inorganic minerals were in large measure identified, and the principal cations were identified. The fine solids were studied as m their mineral identification and the extent of their electrical charges. Test work was done using polyrthylene oxide (PEO) and a liquid cationic polymer along with adjunct additives to determine optimum amounts of these coagulants for minimum consumption and optimum settling efficiency.

Jan 1, 1990

By R. V. Ramani, K. V. Raj

"The air flow problems in open pit mines are complex. Computational fluid dynamics (CFD) models provide a detailed knowledge of the airflow pattern and velocity distribution, temperature, and pollutant concentration within an enclosed domain of the open pit. A range of turbulent model can be selected for varying complexity and accuracy. Pollutant transport models, however, differ in their assumptions and structure as well as in the algorithm they use; as a result, prediction varies from model to model. This paper presents a study of pollutant transport in an actual open pit mine under stable boundary layer. The objective is mainly to test two turbulence models using the same input conditions, model constants, and similar geometry. Measured data are used to compare results of the two CFD models, namely, the kappa-epsilon (?-e) model and the Large Eddy Simulation (LES) model. Despite the complex synoptic situations, different meteorological input data and the fast changing conditions, the simulation results from both the models are in good agreement regarding the dispersion of pollutants.INTRODUCTION Modeling of contaminant transport under Arctic air inversion is an important step for an assessment of the amount of pollutants within the open pit. The Airflow in open pit mines is of larger scale and does not follow the principles of pipe flow. The air flow problems in actual open pit mines are thus far more complex. CFD models provide a detailed knowledge of the airflow pattern and air velocity distribution, temperature, and pollutant concentration within an enclosed domain of an open pit. There is no known application of CFD in three-dimensional modeling of air flow in large open pit mines. Two equation RANS kappa-epsilon (?-e) and Large Eddy Simulation (CFD) models, however, have been developed to solve the stable boundary layer (SBL) problems in Atmospheric Sciences (Baklanov 2000, Basu and Porté-Agel 2006, Dop and Axelsen 2007, Bandopadhyay et al. 2014). Because an exact flow situation in open pit mines is not known a-priori, it is therefore, necessary to investigate various turbulent models to identify the appropriate model that would simulate the flow phenomena with reasonable accuracy, and predict the contaminant distributions within the pit. Dispersion models differ in their assumptions and structures as well as in the algorithm they use and, as a result, predictions vary from model to model. Furthermore, it is also important to investigate the behavior of a CFD model in simulating a complex phenomenon such as the transport and distribution of contaminants in open pit mine under Arctic air inversion. The simulation of an enhanced period of turbulence in SBL is of particular interest because traditional air pollution dispersion models cannot explicitly treat such intermittent events, and yet the SBL is often the worst-case scenario in an open pit pollution transport"

Jan 1, 2015

By D. R. Lowe

Silicic volcanic ash and its alteration product, bentonite (montmorillonite and cristobalite), occur widely within sedimentary phosphate deposits. The genetic link, if any, between volcanism and phosphate deposition has yet to be satisfactorily established The phosphatic member of the Santa Margarita Formation (upper Miocene) in northwestern Ventura County, California, consists of approximately 15 per cent volcanic ash and bentonite. Ash and bentonite units greater than one foot thick can be subdivided into a lower zone of airfall origin and an upper zone of mixed ash and terrigenous detritus washed in from surrounding land areas. This upper zone also contains up to 20 percent phosphate pellets. These thick volcaniclastic units are typically overlain sharply by thin beds (less than 6 inches thick) of relatively pure, silica-cemented pelletal phosphorite. The shelf basin in which the phosphatic sediments accumulated was characterized by quiet, reducing but not euxenic bottom waters; Abundant decaying organic debris, mainly diatoms, served as a reservoir of readily available phosphate. The sudden influx of a large volume of silicic volcanic ash into this basin and its subsequent alteration to montmorillonite had two profound effects on thechemistry of the interstitial and bottom waters: (1) during alteration magnesium was removed from these waters and incorporated into the montmorillonite lattice, and (2) the pH of these waters increased as alteration progressed Both of these effects led to the crystallization in the bottom waters of carbonate fluorapatite. This accumulated as thin phosphorite beds immediately above the volcaniclastic units.

Jan 1, 1972

By Hasan Sevim

A computerized heuristic model for an efficient and economic design of belt haulage networks in underground coal mines is discussed. The model is versatile, easy to use, and is valid for all mining methods singly or in combination. It may be used to design new networks or to analyze existing networks. The input data required are 1. maximum production rates from a section, 2. probabilities of production rates, 3. equipment costs, and 4. data necessary for network coding to represent different cases. The objective function is the "expected minimum cost per ton of coal hauled" while meeting production requirements. The output includes belt width, motor horsepower, bin size etc. and also values of operating parameters for each belt such as belt speed, effective tension, power consumption etc. A detailed account of the cost involved is also provided for each unit as well as for the entire network. Description of the model and an example of the design of a belt network in a mine with two longwall and four development sections are presented.

Jan 1, 1986

By Richard R. Klimpel

The purpose of this paper is to summarize some of the author's experiences in applying population balance models to a variety of industrial grinding circuits. Over 26 separate industrial circuits have been studied in detail during the last 10 years, each unique in its equipment type and layout as well as in the material (s) being ground. The success of the population balance approach during these studies was variable. Fourteen of the circuits were shown to be very amenable to such an approach while the remainder had conditions present that sufficiently violated the standard population balance assumptions so that the analysis was of less than optimal utility. Some discussion of the importance of standard population balance assumptions will be given. It is increasingly becoming this author's opinion that the use of population balance models has its greatest utility in defining logically and cheaply (in contrast to actual physical testing), the relative limits and comparisons of different proposed circuit configurations and changes in equipment types and/or operating conditions. As far as specific quantitative predictions and actual optimization of existing plant performance, the results of applying the population balance approach have been often disappointing and need to be coupled at the plant level with other engineering quantification techniques in order to achieve desired improvements.

Jan 1, 1992

By Mark R. Stanton, Douglas B. Yager

Integration and synthesis of mine-site topography, geophysical, and geochemical data yields both two- dimensional and three-Amensional perspective models for the May Day mine located in the Cement Creek drainage near Silverton, Colorado. Induced polarization, geophysical data are spatially registered with geochemical data acquired from drill hole cuttings that are contoured m three-dimensional space, thereby permitting determination of the most metalliferous and sulfur rich zones of a waste pile. This spatial modeling application was developed to be a visually intuitive tool to aid in mine waste reclamation.

Jan 1, 2000

By Wenhua Wan, Jan M. Mutmansky

Many concerns have been expressed worldwide regarding the use of diesel equipment in underground mines due to the potential health risks associated with diesel particulate matter (DPM). In assessing the risk to the health of miners and designing control strategies for DPM, it is important to know the concentration of DPM in the working areas of a mine. In some mines, significant stratification occurs due to the characteristics of the diesel exhaust, affecting exposure and the ability to measure DPM concentrations accurately. This study outlines some of the concentration profile data obtained during sampling at three mines where diesels were employed. Mine #1 (a gold mine) employed large openings in which a diesel-powered roof bolter was used. Mines #2 and #3 are both room-and-pillar operations with varying conditions. Mine #2 is an experimental mine where two stationary diesels were utilized for sampling purposes, while Mine #3 is a traditional evaporite operation using two mobile diesel vehicles for section haulage. These field studies indicated that some level of stratification occurred in all the mines, but the stratification was not as pronounced in the case of Mine #2 due to the complex pattern of exhaust emissions generated by the vehicles. The stratification seemed to depend on the distance from the vehicle, the mine air velocity, whether the vehicles were moving or stationary, and whether the exhaust was diluted by equipment design features. The concentration of DPM was generally higher at samplers located near the roof and lower at samplers located near the floor. However, this was not found in all cases. This paper provides conclusions on how knowledge of stratification patterns can be utilized in sampling and control of DPM in mine atmospheres.

Jan 1, 1997

By D. M. Milne, H. H. Kanduth

INTRODUCTION The past few years has seen an increased interest in the determination of statistically valid properties of a rock mass. The increased use of computer modelling for the study of rock excavation behaviour has created a need for upper and lower statistical bounds for the properties of a rock mass being modelled. Obviously, to determine the statistical properties of a large volume of rock, many samples must be tested - an expensive proposition when using conventional testing facilities and procedures. As a result of high costs per sample, sufficient tests for statistically valid results are rarely done. In an effort to reduce both sample preparation and test facility costs, an instrument called the Bemek Advanced Rock Tester (BRT) was developed in Sweden. With a total weight of approx. 35 kg, the BRT is portable and sells at a small fraction of the cost of a conventional testing machine. It is comprised of a small 65 KN loading frame with attachments for a variety of tests (see Table 1) , a hand operated hydraulic pump, an electronic balancing unit and a programmable microprocessor. The microprocessor is capable of storing data, performing arithmetic operation on, and printing signals from, a transducer and two strain gauges. A detailed description of the apparatus is given by G. Swan et al. (1). The proposed test strategy involves first a 3-point flexure test on a notched core specimen, followed by a 4-point flexure test on the separated specimen halves. Finally, point load and Brazilian tests can be carried out on the quarter parts of the original specimen. Thus specimen preparation is kept to a minimum. These and other perceived advantages have prompted the purchase of this machine and an evaluation of its suitability to provide data on mechanical properties of intact rock for numerical modelling and rock mechanics design at Noranda's underground mines. Details of its performance evaluation and experiences with the unit are discussed in the following sections. [ ] INITIAL OPERATING EXPERIENCE During the commissioning stage the BRT had, or developed, a series of problems, some of which seriously affected its operation. Below are some examples. Poor documentation was the most serious problem encountered. Confusing instructions for the 4-point bend test installation and its microprocessor programing, as well as poor and ambiguous information on the calculation of gauge factors, are some of the difficulties which had to be overcome. Meehan~cal problems occurred, including failure of the hydraulic pump, as well as electronic difficulties with the microprocessor. Other problems with the printer, requiring its replaceqent, were fortunately covered under warranty.

Jan 1, 1986

By Warren N. Warhol

The mutual growth of the rare earth industry and the Mountain Pass Operations was no coincidence. It was the commercial availability of rare earths on a scale first made possible by the capacity of the Mountain Pass Operations that spurred research and development efforts toward new applications for rare earths. The first important demand on Mountain Pass was europium oxide for the activation of red phosphor for color television tubes in 1964. Since that time, other rare earths have become even more important, and Molycorp is continuing to supply an ever widening variety of rare earth concentrates and compounds. We enjoy saying that rare earths are not really rare, and that they are not earths, either. Of course, we are talking about the 15 metallic elements with atomic numbers 57-71, called the lanthanides, which occur in nature always together in very similar proportions. Their scarcity can be gauged by the fact that there is more cerium in the earth's crust than there is tin, and more europium than cadmium. The word "earths" comes from the early chemical term for oxide. The rare earths were discovered as oxides, and the term has persisted.

Jan 1, 1980

By S. Chander

The effect of pretreatment potential on the response of a gold electrode for Eh measurements in sulfide solutions was examined in terms of measured Eh values and electrode response time. The electrode response time is defined as the time required for the electrode to reach a steady-state value. The relationship between measured Eh values and the hydrosulfide ion concentration is established. The effect of pH, the reversibility of the gold electrode in the sulfide solutions, and the reproducibility of measurements are also investigated. A mixed potential theory is proposed to explain the observations.

Jan 1, 1989

By N. Edmonson

Introduction An examination of statistics for the world phosphate fertilizer industry since 1980 reveals that there is an increasing tendency for fertilizer-manufacturing activity to concentrate in the areas of phosphate-rock mining. The economic justification for this resource-oriented strategy is clear. The choice between shipping phosphate rock, a comparatively low-value product, and shipping a more valuable finished fertilizer product will always, as long as cost considerations control the decision, be resolved in favor of the latter. The historical existence of substantial phosphate fertilizer-manufacturing capacity, which is oriented toward fertilizer-consuming activities and dependent on imported phosphate rock, shows that narrow cost considerations have not always determined the industry's location. One is entitled to ask what conditions have changed to precipitate the observed relocations, and how permanent are these changes. These questions are the subject of this investigation. Recent trends in world phosphate trade Since 1980, the changing pattern of world trade in phosphate materials reflects an increased interest in manufacturing phosphate fertilizer in rock-producing areas. This is shown by the decline in the total tonnage of phosphate rock being traded worldwide compared to world consumption of phosphate fertilizers (Fig. 1). This relative decline has continued since 1984, which is a longer period of time than could be explained by temporary cyclical market factors. Other evidence corroborates this conclusion. The world's phosphate-rock production is relatively concentrated geographically. In 1992, the top ten producing countries accounted for 92% of world production. Figure 2 shows that the share of world fertilizer production in the top ten rock producers has increased. Yet, further evidence of the direction of trade changes can be had by looking at the pattern of the world's sulfur trade. The first step in the manufacture of any of the widely used phosphate fertilizer products is the acidulation of phosphate rock with sulfuric acid. In most instances, phosphate fertilizer producers have found it economical to produce their own sulfuric acid by burning elemental sulfur, and such operations account for over 60% of all sulfur consumption in the world. 1 Therefore, a concentration of phosphate fertilizer production in rock-producing countries should produce a similar concentration of sulfur imports in the same countries. Figure 3 suggests that there has been a tendency since 1989 for sulfur exports to go increasingly to the rockproducing countries. World phosphate-location strategy is not limited to the alternatives of shipping rock and shipping finished fertilizers. A third alternative consists of producing phosphoric acid, the principal phosphate fertilizer intermediate, at the rock deposit, and then exporting it to market-oriented ammonium phosphate plants. This arrangement offers the importing country the advantages of shipping a more concentrated product while retaining the economic multiplier benefits of a domestic high-analysis fertilizer industry. India, and several other countries, imports merchant-grade phosphoric acid to use as input for the domestic value-added fertilizer industries. For various reasons, the trade in phosphoric acid has never quite lived up to the promise suggested by the foregoing discussion. Figure 4 shows no growth in this trade in the last ten years, either in absolute terms or in relation to the world's consumption of phosphoric acid. Most of the decline in the trade in phosphorous in rock form has been replaced with trade in finished fertilizers. The trade in superphosphoric acid was a growth activity in the late 1970s with the growth in US exports to the USSR, and this trade survived the Carter-era embargoes of US-Soviet trade. However, no additional sizable markets for superphosphoric acid developed, and other suppliers sought out the Soviet market. The problem with superphosphoric acid is that the cost of its incremental concentration is as great as the savings from shipping the more concentrated product. The Soviet market was a special case. The political breakup of the Soviet Union disrupted the superphosphoric acid trade after 1991 and led to a shutdown of the US export capacity.

Jan 1, 1996

By P. Bevilacqua, G. Ferrara

Hydrocyclones and other dynamic separators are normally fed with pulps consisting of water and solid particles. The solids usually consist of particles of different sizes, shapes and densities. Except in the special case of monocharacteristic particles, the particles are segregated by these differences in size, shape and density. Segregation is magnified by the high values of centrifugal acceleration in the hydrocyclones. This paper develops a segregation theory that indicates the major variables involved. Experimental data on segregation under different operating conditions for mixtures of magnetite and/or ferrosilicon and nonmagnetic minerals are reported.

Jan 1, 1997

By D. Elsworth, M. Bai

The influence of mining on the hydro-geo-mechanical environment can be greatly modified by alternating mining geometries. The limiting magnitudes of surface subsidence and groundwater flow over the mining area, as a result of mine geometric changes, can be reasonably predicted through the coupled finite-element model introduced in this paper. The model has been verified using real and conceptual case studies which reveal that changes in strata conductivities are strongly related to the strata deformation induced by mining. The greatest modification of hydraulic conductivities occurs within the caving or severely fractured zones. The study indicates that narrowing the panel face width will substantially reduce both the intensity and extent of mining damage to the overlying strata, limit surface subsidence and constrain the change in hydraulic conductivity to a reduced scale and smaller extent, particularly as mining depth increases.

Jan 1, 1995

By Errol vanHuyssteen

Old tailings from Zn, Au, Cu, and Ni mining operations were characterized. Their mineralogical variation in depth is compared with matching pore water and solids chemistry. A geochemical model was used to predict minerals precipitating from pore water solutions. These are compared with actual secondary minerals occurring. The degree to which the precipitation of secondary minerals controls the sulfate and iron concentration of the pore water was also investigated. The results obtained are related to the selection of the most appropriate modes of tailings deposition.

Jan 1, 1998

By Peter Van deVelde

Many companies in North America because of economic or environmental reasons are considering reprocessing material from their waste ponds. The Japanese have developed highly specialized machines and techniques to reprocess industrial/mining wastes from settling ponds. This paper discusses the techniques and results of applying this technology to North American applications.

Jan 1, 1983

By A. A. Sonntag, I. Szanto, D. A. Goodman

This paper presents the most recent developments in mixer-settler technology directed towards treating higher throughputs, increasing efficiencies and providing further improvement in SX technology with a new concept: the submerged launder. Industrial plants built in the last past few years and using these improvements are described.

Jan 1, 1993

By T. Ruff, J. Steele

The lack of visibility near earthmoving equipment results in an average of five fatalities in U.S. surface mines each year. These accidents occur when a piece of equipment either strikes another vehicle or worker, or travels over the edge of an embankment. Researchers at the National Institute for Occupational Safety and Health have evaluated off-the-shelf proximity warning systems that sense obstacles near the equipment and provide an alarm to the operator. Limitations of existing systems have necessitated the development of new systems designed specifically for mining equipment, including a GPS-based proximity warning system and a computer-assisted stereovision system.

Jan 1, 2004

By K. N. Han, Y. Guan

[The dissolution behavior of copper and gold from their pure state and from Au-Cu alloys in cyanide solutions has been investigated using a rotating disc. Oxygen was used as an oxidant. The effect of the alloy composition, stirring speed of the disc. [lixiviant] concentration, solution pH and temperature on the overall dissolution kinetics has been studied. An-Cu alloys of three compositions were used in this study. The atomic percent of gold in these alloys was 75, 50 and25, respectively. The dissolution behavior of these three alloys was compared, under the same chemical conditions, with that of pure gold and pure copper. In general, the dissolution of copper and old from alloys is controlled partially by surface chemical reaction and largely mass transfer.]

Jan 1, 1994