Search Documents

By Dennis Dolinar

In this National Institute for Occupational Safety and Health (NIOSH) investigation, numerical modeling is used to evaluate the degree the pillar strength is increased with a rectangular pillar over a square pillar. Three-dimensional models are developed with pillar sizes and geometries typical of underground limestone mines in the United States. Physical properties for the models are based on geotechnical surveys of nearly 30 underground limestone mines. To examine the effects of pillar length on pillar strength with the modeling, a parametric study was conducted where the pillar width was held constant while the length and height were varied resulting in width-to-height ratios ranging from 0.5 to 1.5 and width to length ratios ranging from 1 to 6. There are two aspects to pillar strength and failure. At relatively low stresses, pillars can fail as a result of geologic structure. At greater depths and sufficient extraction ratios, the pillars can also fail as a result of the vertical stresses exceeding the pillar strength. The effects of increasing pillar length regarding both strength aspects are presented in this study. Equations were developed for the increase in pillar strength with both height and length based on the model results. The results from these equations were compared to those from previously developed empirical equations for rectangular pillars. For the more slender limestone pillars with a width-to-height ratio below one, there is little increase in pillar strength for length-to-width ratios above 2 and almost no increase with length for a width-to-height ratio of 0.5. Only with the more squat pillars is there a significant improvement in strength with length. The gain in pillar strength with length for the pillars is explained by the change in the ratio of the area of the pillar affected by the ends to the area of the pillar. For the squattest pillar, the change in strength is also affected by an increase in pillar confinement along the central length of the pillar as the pillar transitions from a square to a long rectangular pillar. With geologic structure, added pillar length can significantly improve the pillar strength, depending on the strike of that structure with respect to the long pillar axis.

Jan 1, 2007

By Dr. Daniel W. H. Su

t is both an honor and privilege for me to nominate Dr. Daniel W. H. Su for the inaugural Syd S. Peng Ground Control in Mining Award. I can think of no better candidate than Daniel that is deserving of this award ? an award to recognize technical excellence in advancing ground control technologies [and] approaches. Daniel?s education and career spans over three decades. Having graduated from National Cheng Kung University in Taiwan in 1972 with a B.S. degree in Mining and Petroleum Engineering, he spent the next four years in the Taiwanese military and mining industry, before moving to the United States, where he enrolled in West Virginia University?s Mining Engineering Department. He received his M.S degree in Mining Engineering from WVU in 1978; then in 1982 became the first person to ever receive a Ph.D. in Mining from WVU. His thesis was titled, ?Development of Ultrasonic Techniques for the Measurement of In Situ Stresses?.

Jan 1, 2006

By Thomas A. Bailey

Since the advent of longwall mining, various methods and materials have been used during relocation to control the intrusion of the gob in the shield/panline area. (figure 1) Controlling this gob is critical to ensuring a safe, speedy, and productive longwall move. An uncontrolled gob can cause a number of problems, from increased worker exposure to entrapment of equipment to lost production. With an eye toward worker safety and increased productivity, several different methods have been developed to minimize gob intrusion. This presentation will take a look at the history and development of longwall ?screens? and ?mesh?, from chain-link fencing to high-modulus polyester geogrids. The benefits and advantages of these developments will be defined. Since 1994, longwall coal mines have used polymer geogrids during longwall recovery to control intrusion of gob material into the shield/pan line area. As described by Brandon and Collins (1996) in their paper presented at the 15th Ground Control Conference in Golden, CO., mines had used various forms of support, such as welded wire mesh, chain-link fencing, wooden cribbing, props, and steel cable to accomplish this. These methods worked, but were labor-intensive, slow, and provided varying degrees of gob stoppage. Although a few mines still use chain-ink fencing to control the gob, longwall coal mines have generally settled on polyester geogrids to control gob and roof and these mines have been instrumental in providing input in order to develop and improve these geogrids products. he trend during the past twelve years has been to incorporate stronger grids and to eliminate auxiliary reinforcements, such as steel cables and nylon or polyester webbing. A job that once required heavy steel cables, props, and fencing is now accomplished with strong, lightweight, high-modulus polyester grids. When we discuss high-modulus grids, we refer to the ratio between load and strain, as illustrated in figure 2. These grids are woven or knitted from yarns that have been pre-stressed. When these grids come under load, they pick up the load more quickly. This allows less deformation in, in this case, the mine roof. The same principle applies when these grids are used to control the ribs. With less elongation, the grids will hold rib material tighter, thereby keeping travel ways more open.

Jan 1, 2006

By Kot Unrug

Mine seals are necessary in nearly every mine to isolate mined-out areas from the ventilation network. There is a large number of seals in active mines and that number continually increases as the development spreads across the reserves. The recent accident caused by the failure of seals in the Sago mine resulted in new regulations. These regulations have been set based on a principle of eliminating the risk of failure, rather than the sound engineering and understanding of the conditions that may cause seal failure during an explosion of methane in sealed areas of the mine including the probability of such occurrences. This paper discusses the following subjects related to mine seals: The potential causes of methane explosions and the dynamic effects of pressure wave propagation. Seal materials and methods of construction in view of the interaction of the seal with the host rock environment as well as requirements for gathering geotechnical data. The design of seal dimensions is based on loading conditions, therefore the probable ranges of such loading is reviewed. There is also discussion of possible methods for shielding of seals from pressure pulses following an explosion. Particular seal?s types are examined in reference to the conditions at the seals location. A novel design is presented that will be a low- cost solution for the sealing of mined out areas. Recommendations are given for further research leading to a rational engineering system for design of new seals in coal mines.

Jan 1, 2008

By Kot F. von Unrug

One of the major difficulties in the proper characterization of rocks surrounding excavations is the lack of data. The existing method for strength determination requires core drilling for sample collection, which, when performed from the surface is costly, and when performed underground, in addition to its cost, interferes with the mine operations. I-landling samples tested in the laboratory is troublesome and also influences the obtained results. Over several years. the author has been interested in developing a method of in situ strength determination that could rapidly generate strength data at low cost without a negative effect on mining activities. The recently developed borehole penetrometer is an improved version of the initial design ( 3 inches in diameter), which was used mainly for strength determination of coal pillars. The new penetrometer has been designed to work in 1.5 inch diameter holes. Such holes can be drilled at low cost with either hand held drilling machines or roof bolters. eliminating limitations of the previous system and opening the possibility of broad application. Strength testing of roof rock around longwall pillars is an example of an obvious benefit when designing secondary roof support. In the paper are given the principles of work of the apparatus and examples of the obtained strength data.

Jan 1, 1998

By Nic Slatalla

Resin anchored rock bolts are an effective tool to control the deformation of an underground opening because they combine high support capacity with fast installation. However, there are still numerous shortcomings concerning the understanding and interaction of the system bolt-resin-rock. Field and laboratory test series have been conducted for evaluating the load capacity and bond strength of resin grouted rock bolts in different host rocks under axial load. This paper describes that the behavior and shear strength of the system bolt-resin-rock depends on the rock type and discusses a simple correlation between peak shear strength and shear stiffness in the ratio 1:1000 which may moreover be helpful for estimating rock bolt capacity after installation.

Jan 1, 2006

By Collin Stewart

Bowie Resources maintains one of the most pro-active ground control programs in the U.S. mining industry today. Its guiding philosophy is that everyone in the organization, from the miners at the face all the way through the top management, are involved in ground control. Some of the unique elements of the Bowie ground control program include: ? Roof bolt operators log the stratigraphy of test holes in nearly every cut. These ?lithgraphs? are used by section foremen to determine the need for additional roof support, and they are entered into the geologic data base for use in geologic modeling and mapping. ? Underground core drilling is conducted to obtain data for CMRR and stability maps. ? Weekly ?Quality? meetings, involving mine management and technical staff, are held to ensure that ground control information is integrated into production operations. The paper will describe the program in detail, discussing the involvement of roof bolters, section foremen, surveyors, technical staff, and production managers. It will also show how the program has contributed to the mine planning process. Case histories of successful ground control interventions will be discussed.

Jan 1, 2006

By Luis Giraldo

The installation procedure of fully grouted rebar bolts requires that the bolt be pushed through the resin grout until it is fully inserted in the borehole. Resin grout is a highly viscous fluid that is forced to flow through the annulus between the bolt and the borehole as the bolt advances. Variables such as bolt insertion speed, bolt vs. borehole diameter and grout viscosity determine the magnitude of the pressure generated ahead of the bolt tip. Under weak rock conditions, the magnitude of the pressure of bolt insertion is often sufficient to initiate hydraulic fracturing along joints or bedding planes that allow injection of grout into the strata leading to significant loss of bolt encapsulation. The grout pressure front has also been linked to gloving, a bolt installation problem that reduces bolt effectiveness. A series of tests were conducted to characterize the pressure of bolt insertion during bolt installation under various conditions. Analysis of the data shows three distinct stages of pressure build up during bolt installation. Understanding of the mechanisms involved may allow development of strategies for controlling the pressure buildup and its negative impact during roof bolting under weak rock conditions.

Jan 1, 2006

By Jin He

Based on the simple-beam theory, a stress analysis model was established for undermining in multiple seam strip-pillar mining when the strip pillars were not columnized; the effects of various mining factors (e.g., mining depth, inter-burden thickness, recovery ratio, etc.) on inter-burden stability were analyzed; the changes in inter-burden stress distribution were investigated; and the important role that the inter-burden spacing and the mining width of the lower seams on inter-burden stability was studied. Finally, the actual practice used in Feng Feng Mine area was used as an example to demonstrate the rational mining width for a fixed mining depth.

Jan 1, 2006

By Jessica M. Wempen, Michael K. McCarter

"Differential Interferometric Synthetic Aperture Radar (DlnSAR), a satellite-based remote sensing technique, has potential application for measuring mine subsidence on a regional scale with high spatial and temporal resolutions. However, the characteristics of Synthetic Aperture Radar (SAR) data and the effectiveness of DlnSAR for subsidence monitoring depend on the radar band (wavelength). This study evaluates the effectiveness of DinSAR for monitoring subsidence due to longwall mining in central Utah using L-band (24 cm wavelength) SAR data from the Advanced Land Observing Satellite (ALOS) and X-band (3 cm wavelength) SAR data from the TerraSAR-X mission.In the Wasatch Plateau region of central Utah, which is characterized by steep terrain and variable ground cover conditions, areas affected by longwall mine subsidence are identifiable using both L-band and X-band DlnSAR. Generally, using L-band data, subsidence magnitudes are measurable. Compared to X-band, L-band data are less affected by signal saturation due to large deformation gradients and by temporal decorrelation due to changes in the surface conditions over time. The L-band data tend to be stable over relatively long periods (months). Short wavelength X-band data are strongly affected by signal saturation and temporal decorrelation, but regions of subsidence are typically identifiable over short periods (days). Additionally, though subsidence magnitudes are difficult to precisely measure in the central Utah region using X-band data, they can often be reasonably estimated.INTRODUCTIONDifferential Interferometric Synthetic Aperture Radar (DlnSAR) is a satellite-based remote technique that can be used to measure surface displacement over large regions with high spatial resolution. Under good conditions, displacements can be measured with centimeter to subcentimeter accuracy (Buckley, 2000; Massonnet and Feig!, 1998). DlnSAR also has high temporal resolution, and imaging periods typically range from 10 to 50 days (Rosenqvist, Shimada, and Watanabe, 2004; Roth, 2004). In the last two decades, the application of DlnSAR for mine subsidence monitoring has been demonstrated in coal basins in Europe, Australia, China, and the United States (Camec and Delacourt, 2000; Ge, Chang, and Rizos, 2007; Ge et al., 2008; Ismaya and Donovan, 2012; Ng et al., 2010; Perski, 2000; Perski and Jura, 2003; Popiolek and Krawczyk, 2006; Wegmuller et al., 2005; Wright and Stow, 1999; Zhao et al., 2014; Xinglin et al., 2014). Overall, these studies have demonstrated good data resolution, strong relationships between mine development and subsidence, and reasonable agreement between displacements measured by DinSAR and displacements measured by conventional surveys."

Jan 1, 2016

By Frank E. Chase

During the past quarter century, coal mine geologists have evolved from providing a qualitative description of drill core and coal reserves into quantitative geotechnical specialists who bridge the gap between geology and engineering. In the late 1970?s and early 1980?s, hazard prediction mapping was in its infancy. At best, hazard maps identified rudimentary structures and conditions such as stream valley locations, sandstone/shale transition zones, and lineaments. A ?technical disconnect? had existed between geologists and mining engineers as each profession operated largely independent of each other. Engineers did not readily integrate geology and geologic conditions, with the exception of coal thickness, into mine planning. Geologists were relied upon for reserve estimates and did not participate in mine planning or design. The employment and market slump of the 1980?s and 1990?s combined with mining more challenging reserves mandated that this gap be bridged and forced geologists to learn to speak more ?numerically? to engineers so they could be understood. The purpose of this paper is to describe the procedures and thought processes used by coal mine geologists when determining various mineability and reserve extraction feasibility issues. The paper will also address underground geologic hazard mapping and prediction techniques. To achieve these objectives, the opinions and experiences of leading coal mine geologists, geotechnical and strata control specialists across the United States were solicited.

Jan 1, 2006

By David Hill

The Australian underground coal mining industry is increasingly operating in an environment that challenges traditional concepts of coal pillar design, against a background of heightened expectations and demands from other stakeholders with regard to the protection of both natural surface features and burgeoning civil infrastructure. The result is greater possibility of conflict between mine operators, developers and regulatory bodies, with potential for unnecessary sterilisation of Australia?s coal resources and/or escalating surface development / infrastructure protection costs. On the positive side some significant advances have occurred in the general level of understanding of pillar behaviour and stability, both in Australia and overseas. This paper examines some current issues in coal pillar design, focussing particularly on the application and limitations of analytical models of pillar loading. Established methodologies are reviewed and alternative approaches explored, including examples of key geometrical, geological and probabilistic concepts. Practical experiences from the Southern Coalfield of New South Wales (NSW) are examined for the purpose of highlighting critical variables. Finally, some suggestions are made with regard to the direction and opportunities for future research, with particular regard to coal pillar loading, in the interests of all stakeholders.

Jan 1, 2008

By Wenbing Guo

Strip pillar mining method is one of the most important techniques for mining subsidence control in China. Mining depth is one of the most important factors that affect subsidence in strip pillar mining method. Six numerical simulation models were set up in this paper to simulate surface subsidence of strip pillar mining at different mining depths. The mining depth in these models ranged from 300 to 800 m. The simulated results were compared and analyzed. The results showed that the subsidence factor of strip pillar mining is related to mining depth. While other things being equal, the subsidence factor of strip pillar mining increases logarithmically with increase in mining depth. Their quantitative relationship was established based on the simulated results.

Jan 1, 2007

By Peter B. Lilly

Thank you, Syd, for the kind introduction and for inviting me to give the Keynote Address at this very prestigious gathering of some of the finest intellect and talent in the domestic and international coal industry. CONSOL Energy has been a part of this conference for its entire 24-year existence. We have presented 27 papers over that time. CONSOL employees have also been members of the planning committee for the conference, and we have been pleased to support the event both financially and with many participants. So I am honored to be here with all of you this morning, especially during such a positive period for coal. You can just feel the enthusiasm in this room for our industry, and for this conference. I can tell you, there?s also a lot of enthusiasm and excitement in CONSOL Energy?s boardroom. And our enthusiasm is mirrored on Wall Street. But there remains an ironic twist to all of this attention. Even when times are good, the coal industry seems to go largely unnoticed by the mainstream. Outside of West Virginia and other coal-producing regions, the industry still seems to lack influence and support, at least here in America. As an example, last month, an ABC News crew visited our Blacksville 2 Mine, near here, to do a feature story on increased employment in the coal industry.

Jan 1, 2006

By Yongjie Yang

Experimental study on the strength and deformation characteristics of coal under cyclic loading provides guidance for designing coal pillar which is subjected to repeated mining influence during mining. This paper studies the strength, deformation and fatigue process of No.3 coal from Xinhe Colliery under cyclic loading by the MTS815.03 servo-controlled rock mechanics test system. The results indicate that coal is more susceptible to fatigue damage than other hard rocks. Under uniaxial cyclic loading, the fatigue failure ?threshold value? of coal is smaller than 78% of its uniaxial strength, and there is also some fatigue damage when cyclic loading and unloading experiment is carried out below the fatigue failure ?threshold value?. Axial deformation can be divided into three stages: Initial deformation, steady-state deformation and accelerating deformation. Transverse deformation can be divided into two stages: Stable deformation and accelerating deformation. When the transverse deformation begins to increase rapidly and the deformation recovers only slightly upon unloading, it?s a precursor to failure of coal. Under cyclic loading, fatigue failure develops through a process of compaction, strain hardening, and strain softening.

Jan 1, 2006

By Xinxian Zhai

Jining No. 3 Coal Mine, a subsidiary of Yanzhou Coal Company Limited. China, is a super-large modern mine. The coal mine is not only the first one constructed with five-million tons of designed production capacity in China, but also a modern underground coal mine with coal transportation systems by trains and ships, and with a power plant. Based on the hard roof conditions of the sublevel caving coal face in the fault-affected zone, the authors designed rebar and cable bolts for supporting the tailgate that is separated from the gob by a narrow pillar. With extensometers and borescope, strata behavior was systematically studied during tailgate development: (1). Roof convergence is much smaller as well as roof strata separation between inside and outside the anchored zone. (2). The affected zone during tailgate development is approximately 50 m. (3). Because of serious floor heave and obvious rib convergence, the tailgate finally turned into a reversed-trapezoid from the original rectangular shape. (4). There being many joints and fractures in the pillar, coal is crushed from the elastic bedded structure into loose blocky materials. But the tailgate met the service requirements during longwall retreat mining, and demonstrated that the method of roof support was a success. Since then, roof bolting has been widely used for the tailgate of longwall panels at Jining No. 3 Coal Mine. Keywords: coal mine; bolt supporting; tailgate; convergence of surrounding rock; ground control; strata behaviors.

Jan 1, 2007

By Bruce Hebblewhite

This paper recognises the 25th year of the Morgantown International Ground Control in Mining Conference, by offering a twenty five year review of ground control in the Australian mining industry ? primarily in underground coal. The paper provides an overview of the developments in ground control design methodologies, practices and products. It not only summarises what has been done, but attempts to highlight at least some of the major issues, significant developments, controversies and areas of contention, plus some of the continuing gaps in our understanding or capabilities as we go forward into the next 25 years. Some of the issues included are in relation to: the development of the high strength bolt and cable reinforcement practices widely adopted today and the contrast between stiff and soft systems; a focus on local detail, at the expense of understanding regional stability concerns; dramatic improvements in the use of, and systems available for underground geotechnical instrumentation and monitoring; some of the ground control management trends, including occupational health and safety concerns, availability of suitably trained staff and legislative requirements; the opposing approaches of the empiricists versus the numerical modellers ? is there some middle ground?

Jan 1, 2006

By Collin Stewart

Bowie Resources, LLC (Bowie) has been using the Stability Mapping System (SMS) developed by Dr. Keith Heasley, West Virginia University, since 2005. Seven three-entry longwall gateroads, four longwall panels and a five-entry set of mains have been mined in two different seams in areas originally analyzed with the SMS. This paper compares predictions of mining conditions based on the SMS with actual mining conditions. Specific comparisons include longwall and continuous miner (CM) productivity, longwall tailgate response and support and CM roof bolting requirements. The paper also discusses current thoughts at Bowie on the use of different weighting factors for CM development, longwall face conditions and longwall tailgate support requirements.

Jan 1, 2007

By Marvin B. Thompson

"The depositional model for major Illinois Basin coalbeds is well documented and defined on a regional scale. The model was a driving force during past exploration for lower sulfur and thicker coal deposits. The most attractive coal reserves were known to lie along the flanks of contemporaneous sandstone filled stream channels and were overlain by thick silty gray shale roof. At various distances away from the channels, the depositional model transitioned to black shale I limestone roof, sulfur content of the coal bed increased, and the coal bed often thinned. Understanding the character of roof rock types associated with this depositional model is essential to predicting ground control factors on both a regional scale, and on resolving roof control problems at the mine-site. Additionally, horizontal stress and overburden depth are significant factors that impact roof rock quality and ground control in Illinois Basin mines.Determining the character of several rock types, and defining the primary horizontal stress direction were crucial to a recent successful project at New Future Mine, located in southern Illinois. An inclined slope was constructed from the Illinois No. 5 Coalbed up to the Illinois No. 6 Coalbed through strata that ranged from extremely weak ""stackrock"" and a weak underclay unit, to a massive sandstone unit. Engineering geology, operations management, and Jennmar technical services personnel teamedup to select and install roof support for each strata transition. The project was completed with no injuries and no roof falls.INTRODUCTIONAbundant published information concerning coal deposition, geographic distribution, quantity, quality, and mining conditions exists for Illinois Basin coal reserves. The State of Illinois, through its State Geological Survey (ISGS), has provided decades of research, record keeping, and service to the coal industry. Other excellent sources of Illinois Basin coal information include the Indiana Geologiq1l Survey and the Kentucky Geological Survey. Past research by the U.S. Bureau of Mines (USBM) supplemented the work by the geological surveys, especially in the area of horizontal stress and mining hazards. The National Institute for Occupational Safety and Health (NIOSH) continues to produce publications focused on roof control issues common to many coal basins, including the Illinois Basin. Many of the illustrations in this paper originated in ISGS and USBM publications."

Jan 1, 2010

By Kewal K. Kohli, Stefanie Self

"Three cases of surface subsidence investigated over abandoned coal mines after flooding in one case and dcwatering in two cases are presented in this paper. Mining was conducted by the room and- pillar method at all the mines leaving stable pillars. This paper will discuss the background chain of events and the likely causes of the pillar failure resulting in surface subsidence.CASE NO.1BackgroundThe Pittsburgh scam was mined in 1960 by the room-and- pillar method, leaving pillars (Figure I) through Mine A. located in Monongalia County. West Virginia.The mining height in U1is area was 1.83 m (6 ft) with an average mining depth of 140 m (460 ft). The mining recovery was 62% and the safety factor of the pillars was calculated at 1.15 using the Bieniawski ( 1984) fom1ula. For stable pillar design. a 1.5 safety factor is recommended. A 1.15 safety factor is considered marginal. Pumping continued after the mine was shut down in 1960 to prevent water seeping into an adjoining mine owned by the same company. The pumping ceased on December 12. 2003, and the mine was allowed to flood. The water level rose about 17 m (55 ft) by August 3 1, 2004, based on observations in a nearby borehole. On September 3, 2004 surface subsidence occurred above this area causing damage 10 a residence (Figure 2).Summary of InvestigationThe floor of the Pittsburgh coal scam played a strong role in the pillar failure. In this area, the immediate floor of the Pittsburgh seam consists of about two feet of fireclay. Extensive damage to the surface house was an indication that a major collapse below the surface had occurred. The pillars supporting the overlying strata were evaluated to find the cause of their failure. The pillars in the Pittsburgh seam (sec Figure I) had a marginal safety factor of 1.15 before flooding and were stable for 26 years. Once the mine was flooded the water level in the Pittsburgh seam rose by 17 m (55 ft). Shortly thereafter the fireclay in the floor weakened, resulting in several pillars punching into the floor unevenly making the immediate roof unstable. The overburden strata supported by these pillars also subsided do"" n into the mine, causing damage to several house on the surface."

Jan 1, 2010