Search Documents

By Dennis R. Barratt

Rockbolting is now used extensively as a method of primary support in UK coalmines. Over the past fifteen years an optimum bolting system has evolved, based on a high grade steel bolt and a very strong stiff resin. Where necessary, cablebolts are used in conjunction with rockbolts as a supplementary means of support. The rockbolting system, as currently used, is based on a maximum bolt length of 2.4 m whilst cablebolts are generally 6 or 8 m long. Based on the UK experience, there are situations where it is necessary to extend the bolted horizon above that normally achieved with a 2.4 m long rockbolt. Until recently the only options available were coupled rockbolts or cablebolts, both of which have inherent problems in terms of installation. Flexible Strand Rockbolts (FSR), in lengths of 4 to 6 m, provide the means of being able to extend the normal bolted horizon Other advantages include increased strength characteristics (tensile and shear), able to be installed in the UK standard hole size (26-28 mm), encapsulation using resin capsules, thus offering immediate support, high bond strength compared to conventional strand, and able to be installed using existing drilling and bolting equipment. The FSR is considered to be a new concept in terms of strata control and one that compliments the rockbolting system currently in use.

Jan 1, 1997

By Alan Bugden

Goedehoop colliery in South Africa has experienced a number of substantial roof falls in roadways and intersections. Many of these have been associated with geological slips and/or horizontal compressive stresses. This paper describes a numerical modelling study conducted after one such fall with the objective of clarifying the roof failure mechanism associated with these falls. The fall was located at an intersection and occurred as the last cut was being made to complete the intersection. One bounding surface of the fall was formed by the geological slip; the others were formed by fresh failure surfaces. The fall took place despite the slip being identified as a hazard and additional bolts being placed by the workforce. In conjunction with the modelling work tests were conducted on samples from the roof in which the fall occurred, these gave a U.C.S. of 80 -100MPa. Several in-situ stress tests had already been conducted at the mine; a further test was conducted close to the fall site. The tests show that the largest stresses are horizontal. However, the maximum stresses of 6-12MPa are small compared to the compressive strength of the root. Computer modelling highlighted a mechanism arising from the conjunction of a geological slip and horizontal compressive stresses that could result in tensile failure of the roof leading to the fall. Sensitivity studies were conducted to identify risk factors associated with this mechanism and the modelling results used to assist in formulating a support strategy to combat falls of this nature.

Jan 1, 2003

By Thomas L. Vandergrift

Multiple-scam mining is becoming more common in the United States, especially in the East, where primary reserves arc being depleted, forcing mining companies to develop secondary seams, Although mine engineers and planners are aware of the basic effects of seam interaction and generally follow guidelines for columnizing entries and avoiding load abutments, mine design earn greatly benefit bum more quantitative estimates of scam interaction effects. This paper presents case studies from two eastern mines subject to seam interaction effects where pre-mining stresses were quantified: the Mingo Logan Coal Company's Mountaineer Alma A Mine, and Peabody Group's Lightfoot No. 2 Mine. In each of these mines. mining is being carried out within 60 to 90 ft of overlying longwall and pillar panels under maximum cover of about 1,100 ft As part of overall mine planning and design efforts al these mines. NSA Engineering performed numerical modeling analyses using the non-linear boundary-element code MULSIM/NL Input parameters were calibrated by modeling areas where ground conditions resulting from seam interaction were well documented. By incorporating actual cover loading based on topography and seam dip, and the integrity of remnant, gate road, arid harrier pillars in the overlying mines, the pre-mining vertical stress in the underlying scants was estimated based on the pre-mining stress, plans for mains, gate road, bleeder, and pillar panels were developed. Although mining experience in these areas has beers somewhat limited to date, she designs developed as a result of these analyses have so far proven successful.

Jan 1, 2000

By Hongwei Wang, Hao Zhang, Panshi Xie, Xicai Gao, Youfu Zeng, Yongping Wu, Juan Dou

"The reserves and production of steep coal seams account for approximately 15–20% of the total coal reserves in China and 5–10% of the total annual coal production. More than 50% of the coal is high-quality coking coal and anthracite, based on reviews of steeply dipping seam mining at home and abroad. Fully mechanized mining is considered to be the only safe and efficient way to mine steeply dipping seams. To achieve fully mechanized longwall mining, four issues must be addressed: ground control, equipment stability control, development of complete sets of equipment, and safety. Engineers must focus on many factors of steeply dipping seams, such as the following: stope, roof asymmetrical structure, stability control, “roof-support-floor” system dynamics control, multi-region big-range ground control technology, adjustment false-inclined method, nonlinear layout method, control technology, safety, and development of complete sets of equipment. Engineering practices in China introduce these concepts systematically: fully mechanized mining of medium-thickness seams, fully mechanized high mining of thick seams, fully mechanized caving of extremely thick coal seams, fully mechanized mining of coal seams, roadway support, and so on. A steeply dipping seam is one with a dipping angle in the range of 35°–55°. This accounts for about 15%–20% of the total coal reserves in China. Because of the environment, more than 50% of the coal is high-quality coking coal and anthracite. Mining steeply dipping coal seams is known to be difficult in the mining industry. After the study conducted by Germany, Poland, and the former Soviet Union in the1970s–1980s, the fully mechanized mining basic theory, core technology, and key equipment research have not been a breakthrough. Being fully mechanized is a technological “restricted area” at home and abroad. A lot of steeply dipping seams are excavated by non-mechanized mining, leading to harsh job environments, labor-intensive work, low productivity, frequent accidents, and significant security hazards. The death rate per million tons of coal reaches above 4.0 and is far higher than slow inclined coal seam mining. Making steeply dipping seam mining safe and efficient is a global problem that urgently needs to be solved. Fully mechanized mining is the only way to overcome these problems (Wu, 2003; Wu, Yun, and Zhou, 2000). The realization of fully mechanized coal seam mining must solve four problems. (1) Examine the disaster mechanisms induced by overburden “key strata” mutation under steeply dipping seams as a basis for ground control methods and technical problems. (2) Work to solve the dynamic stability control technical problems of thousands of tons of complete sets of equipment under the steeply dipping seams. (3) Complete sets of equipment must be developed to adapt to the conditions of steeply dipping seams. (4) Overcome the steeply dipping face safety protection technical problems. In the last two decades, a number of universities, research institutes, and enterprises have realized the importance of safety and efficiency of steeply dipping seams in China. This is especially true of Professor Wu Yongping’s “hard coal layer safe and efficient mining” team at Xi’an University of Science and Technology. After several generations’ research and technical work, the team puts forward China’s longwall mechanized coal mining of steeply dipping seams strata control basic theory. This paper puts forth a series of key technologies of fully mechanized mining, develops and manufactures complete sets of equipment by independent innovation, and establishes a perfect face security system, forming a theory and technology system for fully mechanized longwall mining of steeply dipping seams."

Jan 1, 2017

By Paul L. Tyrna

The Fola Coal Co., LLC No 2 surface mine, located in Nicholas and Clay Counties, WV, exploits up to nine coal seams by contour, highwall, and mountain top removal mining methods. After encountering faults, areas of highly fractured coal, and subsidence failures. the mine requested a lineament analysis from the Mine Safety & Health Administration's (Pittsburgh Safety and Health Technology Center) Roof Control Division. The 31 km2 study area was viewed on a LANDSAT-5 band 4 (near infrared, 0.76-0.90 µm wavelength) satellite image with ERDAS Imagine 8.4 software. The software allows image examination under artificial sun azimuths and elevations, resulting in variable tonal characteristics. The study area image was viewed in 45° azimuthal increments from 000° to 315° at artificial sun angles of 10°, 30°, 50°, and 70°, yielding 32 separate images. The interpretation process developed by MSHA Roof Control personnel identified 16 northeast-striking and one northwest-striking lineament that intersected mine property. Faults and areas of roof instability corresponded well with lineaments identified in the study. Successful lineament identification prompted mine management to incorporate lineament analysis as a mine-planning tool for adjacent property, thereby identifying in advance areas that could adversely affect safety and production.

Jan 1, 2001

By John L. Edwards

The underground coal mines in the Lake Macquarie area of the Newcastle Coalfield, New South Wales, Australia are constrained by surface subsidence restrictions as low as 150 mm. The mining environment is shallow, generally between 100 m and 200 m, often multi-seam and commonly overlain by residential development or tidal waters. Most mines use partial or panel and pillar extraction techniques to meet the subsidence restrictions and allow maximum resource recovery. This paper gives an overview of the results of a recent two year government funded research project aimed at developing a mechanistic, geomechanically based mine design criteria for subsidence control. Three extraction layouts were monitored in detail to assess the relationship between mining geometry, pillar behaviour and surface subsidence. Pillars at each site were instrumented with stress cells, convergence monitors and extensometers. Field data was used to initially calibrate, and subsequently, verify stress and displacement predictions made by the three-dimensional displacement discontinuity code, SUBSOL. Back-analysis of the modelling results indicate SUBSOL's capability as a tool to satisfactorily predict surface subsidence magnitudes and pillar loads for alternative pillar and panel layouts.

Jan 1, 1993

By Kot F. Unrug

The shale response to moisture changes and the major finding of the appropriate research concerning this subject are briefly reported in this paper. Also described are mine ambient atmospheric conditions which are responsible for moisture changes in mines. The need for a quantitative measure of the weathering potential of roof. rock is demonstrated in relation to its influence on safety and the potential for increasing the cost of mine operations. The weatherability test presented in this paper has been developed and used in many mines. It imitates the natural process in a mine by subjecting the rock sample to alternating wet and dry cycles. The natural changes are thus accelerated, but are similar to the natural conditions to which the surrounding excavation rock will be exposed. The measure of the weatherability index is the percentage of the initial sample mass remaining after the test as the largest fragment of the sample. Thus, the index changes, from 100% for rock affected by moisture changes which disintegrates completely, to 0% for rock totally unaffected. In this paper, the apparatus and testing procedures are described. Also presented are examples of test results. with a discussion of the design implication to he considered by mine planners.

Jan 1, 1997

By Deno M. Pappas

The purpose of this U.S. Bureau of Mines study was to determine the material stiffness properties of the gob for use in numerical models of rock mass response to longwall mining. Photographs of actual mine gob were used to approximate particle size gradations of gob material. The gradation curve was shifted down to a laboratory scale, and 20 uniaxial compression tests were conducted on simulated gob material from 3 different rock types. The study found that the nonlinear stress-strain curves obtained from the three materials were similar, and could be represented in terms of moduli as follows: Es = 2.36s + 1,360 (1) Et = 0.00181s2 + 9.33s + 294 (2) where Es = secant modulus, psi Et = tangent modulus, psi and, s = stress level (due to overburden), psi. These curves correlated well with the theoretical solution curves developed by Salamon. Other effects on gob behavior were attributable to these studied factors including void ratio, thickness-to-width shape ratio, and rock compressive strength. The generated equations should provide numerical modelers with a practical means of estimating gob modulus as a function of stress level.

Jan 1, 1993

By Thomas E. Marshall

During the past few years, the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) examined and characterized conditions at a majority of the underground stone mines in the United States. Observations at these mines revealed a limited degree of roof monitoring beyond visual inspection and sounding. When monitors are used, they typically require the miner to measure movement at the roof. If conditions are unstable, the miner may be in a hazardous situation while recording data. Based on this scenario, researchers surmised that a simple, inexpensive monitor with the capability of recording data at a distance from the mine roof would be a safer way to gain the information. Additionally, more widespread use of monitors could potentially lead to better understanding of roof movement in general. A monitor to meet this need was designed, tested, and subsequently improved as experience was gained in its' use at a number of underground stone mines. The Roof Monitoring Safety System (RMSS) can provide an initial indication of movement in roof beams. By understanding and measuring roof movement in underground mines, the potential for injuries and fatalities to mine workers From falls of ground can be reduced. Also, officials at a mine with a history of data are better prepared to make a decision on remedial actions in the event of ground falls. This paper will outline the evolution of the RMSS and how it can be used in a comprehensive pro-active ground control safety program. Also included is a cast history describing how the RMSS was used in an evaluation of the effectiveness of a mechanical impact scaling machine at an operating limestone mine.

Jan 1, 2000

By S. S. Peng

In recent years many roof falls have been conveniently attributed to the adverse existence of a high horizontal stress. The normal practice of not conducting a follow-up study in a roof fall investigation usually leads to a wrong conclusion. This paper describes two cases of massive oriented roof falls in two separate room and pillar mines. The investigation in each case involved the analysis of past history and current conditions from which remedial measures were recommended and implemented. A follow-up period of up to three years was performed to evaluate the effectiveness of the recommended remedial measures. In both cases, high horizontal stress was proven positively not the cause, contrary to the original conviction of mine management Rather, a weak immediate roof was the basic cause Under a weak immediate roof, a proper roof bolting plan and adequate entry width and intersection span must be strictly observed.

Jan 1, 1999

By K. Biswas

So far, all pillar design methods or approaches consider the coal seam as a uniform structure From some mine visits in northern Appalachian Region. it is found that some coal seams have binder or parting material within the coal scan with varying thicknesses and numbers- And it has also been found that these kinds of hinder materials tire prone to weathering when exposed to ambient mine moisture In this paper an attempt has been made to study the weathering susceptibility of parting materials and coal when exposed to moisture and a two dimensional finite element analysis has been carried out to study the effect of the presence of partings on the structural integrity of the coal pillar in terms of short-term and long-term stability.

Jan 1, 1995

By Kazem Oraee-Mirzamani

Blasting operations generate seismic effects in underground mines. These effects apply additional dynamic loads on the support system, which should bear both static and dynamic loads. Static loads are caused by the weight of the superincumbent strata, while dynamic loads occur as a result of blasting in the mining area. Identification of the origin and determination of the support system behavior in natural frequencies is crucial in assessing the stability of underground mines. This is because resonance occurs when a support is vibrated with its natural frequencies, which can cause a vibration with the maximum amplitude and subsequently cause extreme deformations. The mechanism of support system deformation during dynamic load displacement has been studied and numerical simulation for the impact of the dynamic loads on stability of supports is carried out using finite element method. The paper introduces a simple technique for improving stability and safety of mining operations. Results obtained and the methodology adopted in this research can help mining design engineers make decisions on adequate support for active mining operations.

Jan 1, 2011

By Zhou Ying

Based on the mining condition and roof lithology of the 2-3 coal seam at Gengcun Mine, the simulated materials modeling method was used to study the movement process and characteristics of overburden strata movement and to analyze the movement laws of overburden strata during top coal caving mining. Based on the modeling results, variation of the peak abutment pressure and its effect on the top coal's crushing and caving in the mining process was discussed.

Jan 1, 2001

By Alexander Kattner

Surface fractures in urbanized areas show the risk potential of near-surface mining. This kind of mining subsidence damage occurs mainly in areas where hard coal was mined near the surface with very little overlying rock strata. In North Rhine-Westphalia (NRW), the mining authorities assess areas that are at risk for caveins by means of envelopes constructed according to Hollmann and Nürenberg (1972). Drafting abandoned underground structures depends on the assessment of historical documents such as mine plans, mine titles, and operation plans of prior mines in this area. A research and development project establishing a comprehensive Geo Information System (GIS) for hazard prevention was undertaken in cooperation with the mining authorities of NRW. It aims to display the areas endangered by abandoned, shallow underground mines for the purpose of hazard prevention. A tool was programmed using ArcGIS as a result of this project. It is used to digitize underground workings from preserved mine plans, calculate outcrop lines of coal seams and display hazardous areas. In the future, a database of shallow mine workings will be established. The tool will be used for a systematical mapping of shallow workings and assessment of endangered areas.

Jan 1, 2011

By Tom Wynne

In order to shorten the time required and improve safety for a longwall face move, a 36-ft wide longwall recovery room was predriven. The room was supported with specialty bolts, trusses and concrete cribs. Rock mechanics instrumentation was implemented to evaluate the adequacy of the whole recovery system. This included instrumented roof bolts, entry convergence, load cells, and abutment stress in the surrounding pillars. This paper describes the methodology of support and instrumentation designs, and monitoring and evaluations. The results indicated that this method offers the safest and yet faster longwall recovery so far. But the rock mechanics monitoring also indicated some improvements are desirable in the truss system and concrete crib layout.

Jan 1, 1993

By H. Yavuz

A Numerical modelling study using the two dimensional finite difference code "FLAC" was performed for investigating the ability of numerical modelling to predict the performance of yielding pillars. The model was verified by comparing the stress and deformation data obtained from a yield pillar trial application at Welbeck Colliery, a UK coal mine. Two entries with-a 10 m intervening pillar were modelled. Both for development and for side abutment loading stages, the vertical stress measurement data over the pillar and side abutment and deformation measurement data in the roof and floor of the trial entry were compared with the results obtained from the model. Two difficulties were encountered, unavailability of data for caved rock and for the yielding pillar material. These were overcome by back analysis to estimate the unknown field properties of the pillar material and caved rock from known properties of these materials. Results from this model are given and the predictive capability of a finite difference model for two entry yield pillar applications is discussed.

Jan 1, 2001

By Revendra Awasthi

The application of a horizontal inclinometer and a tiltmeter to measure tilt, curvature, and deformations of shallow footings during mine subsidence is described. The measurements were taken during mining of a longwall panel in Southern Illinois and were supplemented with precision level survey data. Monitoring was conducted under a cooperative agreement between the Institute for Geotechnology at The University of Tennessee, Knoxville, the U.S. Bureau of Mines, the National Science Foundation, the Illinois Mine Subsidence Insurance Fund, and Old Ben Coal Company. Six different footings were constructed and instrumented at two sites; one above the panel centerline, and the second inside the edge of the panel in the anticipated zone of maximum tension. A brief description of the inclinometer casing and tiltplate installation is described, and the results obtained from the two instruments on a plain concrete footing compared. Observations of footing deformations and curvatures calculated from the inclinometer and tiltmeter data are also presented, and the results compared with observed structural damage.

Jan 1, 1990

By Larry Stolarczyk

A clear vision of the future coal mining industry was developed into a hierarchy of technology needs by the National Mining Association (NMA) and the Chief Executive Officers of the mining industry. Although improvements in safety and environmental factors were the main drivers in the technology roadmapping workshop sponsored by the Department of Energy, the agile mining machine of the future must efficiently extract coal from deeper, thinner, and more geologically complex coal beds. One of the challenges will be to develop sensors and software that enable clean coal cutting in a changing geologic environment. The roadmap identifies imaging ahead of raining and horizon control within the top ten needed technologies. For these technologies to be adopted by the mining industry, they must be proven to be effective while driving down mining cost and risk. This paper describes how three-dimensional imaging ahead of mining and horizon sensors enable improved ground control and safety in the mining of underground coal.

Jan 1, 2003

By Shiva P. B. Kolli

Surface mining of multiple scams by mountaintop mining methodology is complex in the Appalachian region of West Virginia. Excess spoil from the removal of overburden and interburden is disposed in the adjacent valleys. The valley fills so formed are some of the largest earth constructions, with a relief of 450 ft (137 m) to 650 ft (198 m) and a stretch of 500 ft (152 m) to 2000 ft (610 m). The stability of the valley fills has become an issue of public concern. This paper describes three cases of valley fill slopes. The analysis of each case involved the description of the geo-mechanical properties of different surface and sub-surface layers, and the surface configuration of the slope. Slope stability was carried out using deterministic as well as probabilistic approaches. Based on the analysis, it was found that valley till slopes were stable due to configuration, and the premise that valley fills with great stretch and high volume of spoil tend to be unstable does not hold.

Jan 1, 2001

By Bruce K. Hebblewhite

Underground pillar extraction continues to be practiced in Australia in various forms, in spite of the dominance of the longwall method, which accounts for over 90% of underground production. Australia has been a leader in various forms of pillar extraction, particularly since mechanisation was introduced to the industry during the middle of the 20th century. Historical developments have included a range of thick seam mining pillar extraction methods; the widely adopted Wongawilli method; early adoption of the use of mechanized breaker line supports; and a number of more recent partial extraction systems including what is known as rib stripping. Current pillar extraction practice varies from total extraction panels to various forms of partial extraction, driven by either surface subsidence constraints or by underground conditions. This paper reviews a number of different pillar extraction methods and mining layouts, and also highlighting a number of fundamental geotechnical principles which have been found to be critical for safe pillar extraction ? often through lessons learned the hard way, as a result of back analysis of different accident scenarios. These principles include the all-important understanding of the location of the goaf (gob) edge at any point in the operation, and the management of that goaf edge; the impact of geological structures on local and regional stability; the critical importance of extraction lifting sequences; the role of stooks (remnant pillars); and a number of other factors. The paper will also briefly reference the educational and training practices adopted in Australia aimed at the continuous improvement of pillar extraction safety.

Jan 1, 2011