Search Documents

By Mictck Rataj

Methods of rock reinforcement in Australian coal mines are being advanced progressively through the better understanding of rock failure mechanisms around roadways and the-development of improved bolting hardware and installation techniques. It has been recognised that to improve the performance of rock reinforcement systems, the stiffness of the system as a whole has to be improved. New style bolts and accessories together with high pre-tensioned roof and cable bolts are being developed as a result. A number of the new techniques used to stabilise the roof, especially in weak roof/high horizontal stress areas have been site proven and are now currently used on a routine basis as a means of improving development rates and gate road stability during longwall retreat.

Jan 1, 1997

By Brian Clifford

Thoresby Colliery is in the process of recovering an old roadway that was flooded following the closure of an adjacent mine. The aim is to re-use the roadway as a gate road for a longwall retreat panel and it is therefore important to establish the condition of the existing rockbolt support during the recovery operation. Two NDT methods, ultrasonics and RMT's newly developed RF (Radio Frequency) system were used in combination to interrogate the rockbolts to determine their condition. This paper describes the condition of the rockbolt supports, the NDT methods used and the problems that had to be overcome to successfully apply the two methods.

Jan 1, 2002

By Nikolaos Polysos

To drive and utilise gate roads economically requires accurate planning and risk assessment considering the variable geomechanical requirements. The geomechanical part of roadway planning is secured by geotechnical investigations of drill cores and geophysical borehole logging. The rock specific parameters determined in this way allow a statement about the quality (defomtation and strength characteristics) of the rock that has to be cut across. They set up the basis for a standardised rock assessment. Combined with the prevailing rock mechanical situation, technical boundary conditions for advance and support techniques can be identified already in the planning phase. Detailed geotechnical investigations prior to the planning and driving of roadways can lead to a technically and economically optimised roof support system. Geotechnical core logging and a standardised assessment scheme based on the data acquired will be introduced. Geophysical borehole logging methods provide additional physical data. Different methods and their validity, which may lead to a further improvement of the planning reliability, will also be presented. The geomechanical information gained and their relevance fir the planning will he illustrated. Keywords: rock classification, geotechnical rock parameters. geophysical well logs. support planning

Jan 1, 2002

By Hui Chen

The paper describes the use of a physical model technique to investigate the failure modes of mine tunnels with reference to the in situ stress field. The characteristics of stratification commonly encountered within UK coal mining conditions have been taken into consideration. The investigation has indicated that the weak floor strata in coal mining tunnels, under the action of high rock stresses, will be subject to the floor lift problem in both predominantly horizontal and vertical stress fields. However, the failure mode and mechanism varies between the two stress field patterns. In the predominantly horizontal stress field, the tunnel floor tends to fail by gradual bending of the laminations, whilst in the predominantly vertical stress field, the floor tends to fail by a shearing action with the failed material lifting in the form of a block. The failure mechanism is discussed with reference to mechanics theory.

Jan 1, 1993

By Thomas L. Vandergrift

With the inevitable expansion of homes, businesses, and infrastructure in coal mining regions, the potential for future subsidence above abandoned mines is of increasing concern. Of particular concern are areas underlain by room-and-pillar coal mines. Unlike areas above longwall mines, where total extraction causes subsidence in a predictable and timely manner, subsidence above room-and-pillar mines is difficult to predict and may be active for many decades. As part of a geotechnical assessment of a water pipeline replacement project, NSA Engineering recently performed an evaluation of tong-terns subsidence potential along the proposed alignment due to time¬dependent failure of underlying room-and-pillar workings. The alignment of the replacement pipeline closely follows an existing concrete pipeline, which lies 150 11 to 300 fl above workings that both pre- and post-date the pipeline. Annual surveys along the existing alignment indicate that some subsidence has occurred, primarily from partial pillaring performed in the early 1980's, but that this subsidence is not active. Using the boundary-clement code LAMODEL as the primary analysis tool, NSA followed a three-step approach to estimate future subsidence impacts on the replacement pipeline. First, historical information for the mine was compiled, allowing for calibration of models to actual field conditions. Then, numerical models of workings directly under and adjacent to the proposed alignment were nun, with model input parameters varied until resulting loading patterns matched historical data, and subsidence in the model approximated that measured along survey lines. Finally, time-dependent deterioration of coal pillars was simulated by decreasing the coal strength in the calibrated model until a realistic "worst-case" condition (stability of barriers, but Yielding of production pillars and pillar remnants) was attained. Subsidence from the previous calibrated model was then subtracted from that of the worst case model to estimate future subsidence and related ground movement parameters that slay occur along the proposed alignment. The replacement pipeline design, incorporating couplings capable of withstanding the ground movements predicted, is now being finalized.

Jan 1, 2000

In recent years, improvements made to the longwall system have accelerated at a faster pace than those made to the gate entry development system. As a consequence, unless planned years ahead of time, extending the panel length is nearly impossible without some innovative approach. At Cyprus Amax Coal's Emerald mine the G panel length was extended by 3,500 ft- by developing three entries across it to facilitate development of its headgate and tailgate entries simultaneously when the adjoining F panel was in operation. After evaluating alternative supporting methods and associated risks, determination was made to backfill these entries and crosscuts using a low strength flyash cement mixture prior to mining thru. Instrumentation was also used to monitor the stress change or front abutment stress in both the coal and the backfilled material ahead of the face. Longwall mining thru these three entries took about four eight-hour shifts and proved to be very successful. The designed flyash cement mixture provided adequate roof stability and caused no difficulty in the shearer's cutting while eliminating an in-panel longwall face move and minimizing the risk of roof or floor failure in the in-panel openings, or in the worst scenario loss of the face during the longwall cutting thru. This approach provided the intended result of extending G panel and recovered about one million tons of coal. This paper summarizes the engineering design of the cutting-thru project and flyash cement mixture, front abutment stress changes within the longwall coal block, backfilled material, and coal pillars ahead of the longwall face, and our underground observations

Jan 1, 1997

By D. W. H. Su

Following a roof fall in the B12 headgate of a CONSOL Pennsylvania Coal Company (CCPC) underground coal mine in February 1998, CONSOL R&D and Exploration initiated an underground roof geology reconnaissance program along the B13 and B14 developments to define potential roof instability areas and to recommend appropriate supplemental headgate support. This reconnaissance program revealed the presence of a thick, massive Pittsburgh sandstone channel overlying the B13 and B14 panels. Surface and underground core holes confirmed the close proximity and the very massive, nonlaminated nature of the sandstone. To mitigate anticipated adverse conditions at the B 13 and B 14 longwall faces due to delayed caving of the massive sandstone behind the shields, a task force consisting of Operations, Exploration, and R&D personnel was formed in May 1998. Several operational adjustments were made by mine management, including repairing damaged lemniscate links, maintaining immediate forward shield support, and implementing measures recommended by the task force intended to boost the shield set load density at the face. After reviewing available geotcchnical information, the task force also recommended fracing of the massive sandstone over the B13 and B14 panels to enhance caving characteristics and further reduce the bending-induced stresses in the sandstone near the face. Horizontal fracs were created at a horizon about 25 feet above the Pittsburgh seam main bench over the two panels in June and November 1998, respectively. To evaluate the effect of sandstone fracing and operational adjustments on the bending-induced stresses in the sandstone, three finite element models were constructed and analyzed. Results from the finite element analyses indicate that one horizontal frac, 25 feet above the Pittsburgh seam, would reduce the bending-induced stresses in the sandstone by approximately 50 percent, maintaining them at a level below the ultimate strength of the sandstone. Operational adjustments to increase the support set load density and support stiffness could reduce the bending-induced stresses in the sandstone by a maximum of an additional 10 percent. Shield pressure monitoring at the B14 midface confirmed the presence of a lower roof pressure zone inby and outby the 1314 frac holes. This lower face pressure significantly contributed to improving the B13 and B14 longwall productivity and safety. The total production downtime due to bad top at the B 12 face within the interval of channel influence was 30,600 minutes compared to about 3,500 minutes each for the B13 and B14 faces. The average longwall advance per machine shift for the B13 and B14 faces within the channel was about 70 percent higher than that for the B 12 face.

Jan 1, 2001

By Chris Adams

The application of pre-tensioned tendon roof support assisted Harworth Colliery in their revival, from impending closure to lowest cost deep-mined producer in the UK, over just six months last year. The paper describes this success story, how it came about, the reasons "why", and the method "how"

Jan 1, 2003

By M. K. Larson

The U.S. Bureau of Mines and Cyprus Shoshone Coal Corp. conducted a study of deformation mechanisms around a longwall gate-road system in an underground coal mine. Of particular interest was roof deformation over the headgate entry. The strata above and below the coal seam are very weak, carbonaceous mudstones that have planes of weakness oriented along the bedding. Visual observations of previous gate roads over several years suggested that deformation was time dependent and resulted in creep along joints or crack growth. Instruments were installed at a test site to measure deformation around the entry, strew changes in the pillar, and loads transferred to support systems. Multipoint extensometers, instrumented bolts, instrumented trusses, biaxial stressmeters, borehole pressure cells, and single-point extensometers were installed. Monitoring continued until the longwall face passed the test site by 38.7 m (127 ft). Results show that fracture zones arched over the entry from both ribs, most bolts and trusses were loaded past their yield point, and the largest change in secondary principal stress was almost horizontal in the pillar. Displacement measurements in the roof showed classic primary creep.

Jan 1, 1995

By Yi Luo

The severity of disturbances caused by longwall mining subsidence to various residential structures can be re¬duced. The success of such mitigation efforts depends on accurate subsidence prediction, correct assessments of the subsidence influences, and careful design and implementa¬tion of the proper mitigation measures. This paper presents the systematic approach involved in the subsidence mitiga¬tion efforts with a case demonstration.

Jan 1, 2003

By K. Haramy

Coal mine bursts or bumps involve the violent, rapid failure of coal and rock in or around a mine excavation. Failure is normally associated with high stress and brittle or brittle-elastic materials; in coal mining, bursting may also be associated with desorbing gas, and this type of failure is termed an outburst. This paper discusses factors affecting coal mine bursts and several methods to predict bursts, including microgravity, microseismic, rheological, rebound, and drilling-yield methods. Methods to avoid burst conditions using volley firing, hydraulic fracturing, and auger drilling are also discussed. A case study is presented in which the redistribution of stresses and displacements was found to be associated with a burst at a deep longwall coal mine. The research showed that stresses are redistributed following the burst.

Jan 1, 1984

By R. Karl Zipf

Stress analysis programs such as MULSIM/NL, LAMODEL, MinSim 2000, and EXAMINE TAB are used in the mining industry to analyze stresses and displacements in coal mines, platinum mines, gold reefs, and tabular-type deposits. These relatively simple numerical models can efficiently simulate yielding and failure of a rock mass near a mine opening and subsequent stress transfer. The main input parameters for these models are a family of nonlinear stress-strain curves for the in-seam material. For many applications of these models, such as in coal mining, extensive field measurements and observations exist from which to estimate these stress-strain curves and calibrate the numerical models; however, such measurements are lacking for other types of mines. A three-step method is presented to determine nonlinear stress¬strain curves for boundary-element (BE) programs used in many mining applications. The method requires a suite of laboratory¬scale strength tests at various confining pressures. Note that this analysis uses laboratory-measured strength and modulus properties of alluvium. The dependency of the mechanical properties of alluvium on scale has not been established, although more tests are being planned. However, it is believed that the relative comparisons performed are valuable regardless of scale effects. First, the FLAC2D computer program is used to model the laboratory tests and determine cohesion (c) and friction angle (0) for a Mohr-Coulomb material model. Second, another FLAC2D model uses the c and 0 values to calculate vertical stress and strain around a single opening in the rock mass. This model calculates the stress-strain path of points at various distances from the opening boundary. Finally, based on these stress-strain paths, the stress-strain curves needed for a BE analysis are derived. This three-step method was demonstrated in a large, flat-lying underground test facility in very weak rock. The BE analyses agreed well with observations of failure at the test facility and provided a basis for evaluating the behavior of alternative layouts.

Jan 1, 2003

By John L. Ellenberger

The National Institute for Occupational Safety and Health (NIOSH) has continued the research role of the former U.S. Bureau of Mines to develop techniques that will reduce the hazards in the mining work place associated with coal bumps. Current research focuses on both analyzing historical seismic data from bump-prone operations and utilizing a mine-wide seismic network to investigate the exact strata failure mechanics associated with bump-prone geology. The anticipated outcome of this research will be reduced bump incidences through advanced engineering concepts and designs which implement the new understanding of strata behavior. The analysis of the historic seismic data consists of correlating observed mining seismicity with the geologic and geometric parameters at the sites. The primary seismic parameters are the timing, location and magnitude of a recorded seismic event. These parameters are correlated with such mining parameters as: the overburden, the size of the immediate gob, the size of the district gob area, etc. This detailed analysis of historical seismic data has provided an informative quantifiable relationship between many of the specific mining parameters and the induced seismicity. The second aspect of the coal bump research is the instrumentation of an appropriate field site to determine the main roof, floor, and gob behavior associated with hump behavior. The chosen field site is a deep-cover longwall mine with competent geology in a historically bump-prone area. The primary field instrumentation is a three-dimensional, full-waveform, seismic array with both surface and underground sensors surrounding an active multi-panel district. The purpose of this seismic array is to determine the timing, the exact location, and the mechanism (tensile fracture, bedding plane slip. etc.) of the failure of the strata surrounding the active and multi¬panel gobs. The preliminary results presented in this paper help to define the strata failure areas around the longwall panel.

Jan 1, 2000

By Takashi Sasaoka

EGAT Mae Moh Lignite Mine in Thailand produces about 16 million tons of lignite annually from open-cut mining. The coal is used to generate 2,400 MW of electricity. In the near future, however, the coal must be extracted from underground at 400? 500 m (1,312?1,640 ft) deep from the surface. The problem is the thickness of the coal seams. There are two coal seams that are about 25 m (82 ft) thick with 20?25 m (66?82 ft) of interburden between them. Up to now, many mining systems for thick coal seams have been used and improved in the world. However, where the thickness of coal seams is beyond the limitation of the current mining technology and system, an applicable mining system has to be introduced, considering influencing factors such as caving and subsidence. In order to investigate thick seam mining systems and propose a new mining system in ultra-thick coal seams in Thailand, a joint research group was established by Japanese and Thai researchers and mining engineers in early2009. This paper describes underground mining systems for thick coal seams and proposes an innovative underground mining system for thick coal seam, ?eco-friendly underground mining system?, considering geological, geotechnical, and environmental conditions in this mine. This paper discusses its applicability to this mine by means of numerical analysis from the geotechnical point of view.

Jan 1, 2011

By Cosmo P. Fazio

Remote control roof bolting is approaching reality with the continued improvement of a number of components and subsystems being developed by The Bendix Corporation under sponsorship of the U.S. Bureau of Mines and the U.S. Department of Energy. The era of remote control research in roof bolting was initiated by the USBM in June of 1973 with the award of a contract to Bendix Corporation to design and build a roof bolt bender/inserter device. One year later in June of 1974, the Bureau awarded five parallel R&D contracts to develop a longer-than-seam-height flexible roof drill. The Bendix flexible drill design has been the most successful of the five, has been thoroughly tested in both laboratory and underground situations, and has been incorporated into a number of machine applications along with the roof bolt inserter. The purpose of this paper is to discuss the advantages of remote control bolting from both a safety and productivity standpoint. Applications of the flexible drill and roof bolt inserter on a number of government and industry supported programs are used to illustrate the advances being made toward the goal of remote control.

Jan 1, 1982

By M. Karmis

For several centuries surface subsidence has been recognized as an inevitable consequence of most underground mining. In fact, British court records of disputes and litigations related to property damage due to mining subsidence can be traced to the early fifteenth century (Shadbolt, 1978). The first systematic investigations of the mechanisms involved in mining subsidence can be credited to Belgian Mining Engineers. The re- search effort was initiated after the widespread movements and the resulting structural damages suffered by the City of Liege in the 1920's. The publication of Gonot's 1871 treatise "Loie de la NomZ" (normal theory) was one of the most not- able achievements of the Belgian school of that era (Gonot, 1871). During the past 100 years the phenomenon of mining subsidence has been the subject of intensive research, particularly in Europe where long- wall is the most common method of underground coal mining. Many theories have been advanced to explain the mechanism of ground movement as it develops from the excavation, through the superincumbent strata, to the surface. Such theories include the original concepts of beams, arches, domes and the contemporary mathematical modeling principles of strata movement assuming two extreme concepts-- a continuous elastic medium and a stochastic medium for the superincumbent strata. An excellent review of the development of these theories ?-s given by Shadbolt (Shadbolt, 1978). In conjunction with the theories of mass strata movement in the vicinity of mine workings, the subject of surface subsidence predictions has also been the subject of extensive research. The development of reliable and rational techniques of subsidence prediction is imperative, if this phenomenon is to be recognized and controlled within acceptable environmental levels. Empirical as well as mathematical methods have been proposed to fulfill this objective and a comprehensive analysis of these methods has been presented in the literature (Bramer, 1973; Shad- bolt, 1978; Virginia Polytechnic Institute and State University, 1980). As a result of this intensive research effort, it is now accepted in many )coal fields-- mainly in Europe-- that the state of art in subsidence prediction and control has approached a level where mining induced surface displacements can be predicted to a suggested accuracy of less than + 20 percent. Furthermore, such movements can be translated into anticipated structural failures using established damage criteria, thus enabling appropriate precautionary measures to be implemented. In this country, subsidence is rapidly gaining emphasis as an important environmental problem of underground coal mining. Damage resulting from this phenomenon ranges from land settlement to severe structural damage and has been witnessed in rural (Illinois, Colorado, West Virginia, Virginia, Pennsylvania) as well as in urban areas (Pennsylvania, West Virginia, Illinois, Wyoming). Yet, the art of subsidence prediction and hence control in this country, for both longwall and room-and-pillar coal mining, is far from approaching the maturity reached by the Europeans. In this paper, field measurments and computer modeling techniques have been used to develop some basic relationships of longwall subsidence and its related parameters. Because the objective of this study was to develop regional subsidence trends, all processed information pertains to the Appalachian coal region.

Jan 1, 1981

By Dennis Dolinar

In general, the direction of the maximum horizontal stress in the eastern United States is fairly well defined. However, the variation of the magnitudes of the horizontal stresses is not very well understood. Because the horizontal stresses cause severe ground control problems in underground coal and limestone mines throughout the eastern United States a more complete understanding of how the magnitudes vary would be useful for developing mine design strategies to combat horizontal stress related ground control problems. Therefore, in this National Institute for Occupational Safety and Health (NIOSH) study, the variation of the magnitude of the horizon stresses in sedimentary deposits in the eastern and Midwestern United States are examined with respect to two factors, the elastic modulus of the rock and the site depth. Stress measurements from thirty-seven sites are used in the evaluation. Examining the applied excess strains indicates that the eastern United States can be, separated into high and low strain zones. For most of the eastern United States the maximum applied excess or tectonic strain ranges from only 300 to 550 micro strains. However, there is one area, a portion of the Beckley seam in the central Appalachian region where the strains are significantly higher than the other regions. In this higher strain zone, the maximum applied tectonic strains range from 700 to 1,000 micro strains. Regression models for each zone based on the elastic modulus can explain between 83 to 85% of the variation of the maximum horizontal stress. Because one region, the northern Appalachian district, has strains that are about 20% higher than the other regions in the low strain zone, multiple strain models based on geographic regions were developed for the low strain zone that can explain 87 to 91% of the maximum horizontal stress variation with the elastic modulus. Depth was found not to be a significant causal factor in any increase in the horizontal stress even though the site depths ranged from 275 to 2,500 ft. Beyond a theoretical increase, based on Poisson's effect and gravity, no other increase in the horizontal stress with depth can be justified with this data. The most significant factor controlling the variation of the maximum horizontal stress is the elastic modulus of the rock, not the overburden depth.

Jan 1, 2003

The U.S. Bureau of Mines (USBM) has developed the coal Mine Roof Rating (CMRR) to aid in ground control. This paper describes the application of the CMRR at four coal mines operated by a major U.S. coal company. The mines are widely separated geographically, and cover a wide variety of geologic conditions and mining methods. The study found that the CMRR was a useful predictor of roof performance. In mines where the CMRR varied, and other parameters held constant, roof falls were associated with low CMRR values. Important similarities in roof performance were found in mines with similar CMRR values, despite radically different geologic environments. The analyses also indicated that statistics can be used to evaluate ground control performance. For these mines, a "roof fall probability" can be estimated from the CMRR and the intersection span. A spreadsheet program has been developed to facilitate treatment of CMRR data, and it is briefly describe

Jan 1, 1994

By Madan M. Singh

Currently longwall coal mining operations require at least 3 entries on both the headgate and tailgate ends because of ventilation and safety requirements. Driving of entries, however, is a slow and costly process. Often it is a bottleneck in longwall development. Single entry gateroads are permitted in Europe and commonly used there. This study entailed ascertaining the feasibility of using a single entry in the United States, without sacrificing safety. This design was conducted for an operating longwall mine in the Black Warrior coalfield in Alabama, An understanding of rock loads and consequent support requirements is prerequisite to the design and successful demonstration of the single entry system. Efforts in this regard were directed at determining center (packwall) support requirements for various single entry widths. Critical to the analysis is knowledge of the nature and extent of side abutment stresses. In collecting geological and geotechnical information relating to the stability of the single entry, Engineers International, Inc. engaged in the following: ? Examination and inspection of the single entry demonstration at the Sunnyside Mine in Utah. Severe ground conditions and unacceptable levels of entry closure were experienced there prior to the tailgate phase. Observations at the mine presented a clear perspective on possible ground control problems for future single entry designs. ? Reconnaissance inspection and classification of roof rock conditions. ? Detailed mapping of roof structure in the areas to be instrumented. ? Installation of convergence stations in the longwall headgate to monitor roof movement during mining. ? Measurement of side abutment stresses in a yield pillar in the area of the convergence measurements. ? Measurements of coal fracture distribution by the detail area method. ? Rock properties determinations of roof, coal, and floor rocks; samples obtained by core drilling. ? Determination of floor bearing capacity by in-situ testing.

Jan 1, 1982

By Bill A. Kyslinger

"In underground mining, machine design is predominantly dictated by mine conditions and individual customer desires. In partnership with Foresight Energy, J. H. Fletcher & Company was tasked to design and manufacture a new roof bolting machine with six independent drilling apparatus on board capable of drilling and bolting the roof and ribs with material handling. This is the first Fletcher® six-head machine to be designed and built for the mines in the United States. The machine is intended to work in the Illinois Coal Basin.The objective was to produce a machine capable of drilling and installing six bolts simultaneously with a limited number of operators. The goal of the mine is to decrease the time to bolt a cut to improve the safety level of the current roof bolting method, improve efficiency and to improve the bottom line cost of entry development. The customer wanted four mast feed drills at the front of the machine dedicated to installing roof bolts and then another two mast feed drills behind them dedicated to rib bolts. This dictated the requirement of latched controls, which would allow the operator to start drilling one hole and then latch the controls to be able to move on to the next. To accomplish this, we developed a unique hydraulic latch circuit to maintain operator safety and compliance. Guarding was added to prevent an operator from coming into accidental contact with a latched drill.The result of the design is a machine with a single platform and six independent masts with drillheads: four masts strictly for drilling and installing roof bolts on the front of the platform and two masts on the back of the platform for rib bolts. The feed and rotation controls at each operator's station include a latch control for drilling. The latch control will allow the operator to lock in the feed and rotation once the hole has been collared, allowing the operator to move on to the next hole. The rear of the machine is equipped with material handling. There are two material pods with winch controls as well as a mesh rack that includes mesh lift, mesh tilt, and mesh sump.The six-head roof bolter allows fewer operators to drill and install roof and rib bolts, which in tum lowers the miners' roof exposure per cut. This design reduces the operator's exposure from the inherent pinch points and rotary hazards once he has engaged the latch drilling. Therefore, the machine will help to decrease the time to bolt a cut, improving productivity while enhancing the ability to operate the machine safely."

Jan 1, 2016