Search Documents

By Dion Pastars

Resin based grouts are the main form of rock bolt anchorage in the underground coal industry in Australia and New Zealand. To be effective, the system requires the mixing of the catalyst and mastic components of the resin, as well as shredding of the laminate cartridge that contains the resin. An unknown measure is the load transfer characteristics of a bolt where the resin is well mixed but remains encased in the cartridge (gloved). Laboratory and in situ field investigations have been undertaken to quantify the performance loss due to mixed gloved bolts. This work showed repeatable results, indicating serious performance loss of the gloved and mixed system, with load transfer approximately 10- 15% of a non-gloved system (MacGregor, 2004). The in situ testing has demonstrated the relationship between the adhesion qualities of the resin and the mechanical interlock generated by radial confinement with progressively increasing tensile load. Effective load transfer is defined by the ability of the system to sustain shear stress on the bolt hole wall.

Jan 1, 2005

By Michael Trevits

The NIOSH Lake Lynn Laboratory (LLL) is a unique research facility, located about 50 miles southeast of Pittsburgh, Pennsylvania, that is designed to provide a full-scale mining environment for testing and evaluation of mine health and safety technologies. The LLL occupies more than 400 acres and is composed of surface test and training areas and an underground mine. The Lake Lynn Experimental Mine (LLEM) was built at an abandoned commercial limestone quarry where surface mining ceased in the late 1960's. Later, new underground development was constructed to simulate modern-day coal mining scenarios; including room-and-pillar and longwall mining layouts. In January 1994, a sinkhole opened southeast of the No. 4 Portal of the LLEM and since then, the area of the underground failure and surface deformation has continued to expand and now includes several interconnected sinkholes. A concern developed that the overburden instability could expand and affect the structural integrity of the nearby highwall and the No. 4 Portal. It was unsafe to conduct a detailed underground survey of the mine in this area because the mine roof conditions near the No. 4 Portal had deteriorated significantly. It was decided to investigate the overburden conditions near the No. 4 Portal using ground penetrating radar (GPR). A GPR survey grid was located along an access road that passes over the top of the portal. To delineate the mine conditions near the portal, antennas whose frequency spectra produced pulses centered near 100- and 200-MHz were used. The results of the GPR survey suggests that the overburden rock units appear to be laterally consistent to a depth of about 15-ft. Below that point, the overburden appears to be significantly disturbed and it was hypothesized that this area contains a large roof fall. A follow-up ground truth survey of the mine roof conditions was conducted from the mouth of the portal. It is concluded that the observations and measurements made from the radar records appear to be correct as a large roof fall was observed and measured from the mine portal area.

Jan 1, 2005

By Thomas Barczak

Longwall mines typically use some form of standing support for secondary roof support in longwall tailgate entries. Although there have been several new support products developed for this application, there remains no universal design criteria to optimize the application of these support technologies. The requirement for optimization and proper support selection is to understand the degree of control that the support has on the ground behavior. The ground reaction curve and numerical modeling was used to evaluate the impact of standing support on ground behavior. LaModel was used to evaluate the impact of standing support on main roof and floor behavior and pillar yielding. The conclusion drawn from this study was that standing supports do not have sufficient capacity to control main roof or floor loading or prevent the resulting convergence of the tailgate entry. However, it is imperative that this "uncontrollable convergence" be considered in the support design to prevent premature failure of the support. A FLAC model was used to evaluate the near-seam roof and floor behavior in conjunction with the global vertical and horizontal stresses. The model suggests that standing roof supports can have some impact on the ground behavior as the elastic response of the rock is exceeded and rock structure deteriorates from the stress concentrations that develop around the tailgate opening. During this phase, the capacity and stiffhess of the standing support can be critical to the stability of the opening, as eventually the rock mass will be transformed into a partially detached structure whose weight must be supported by the standing support. This work is part of a ground control program of research at the National Institute for Occupational Safety and Health (NIOSH) aimed at improving mine safety by reducing roof fall injuries and fatalities.

Jan 1, 2005

By J. F. T. Agapito

Overcore measurements at the North Fork Valley (NFV) coal mines in western Colorado have shown that horizontal stresses are highly anisotropic. Measurements have been made in four mines at various depths. In many measurements, the maximum horizontal stress is three to four times higher than the minor horizontal stress. At the West Elk Mine, maximum and minimum horizontal stresses of 24 MPa and 6 MPa, respectively, have been measured at depths of 640 meters (m). Under highly anisotropic stress conditions, ground control problems associated with both high and low horizontal stresses can develop. While high horizontal stresses can produce cutter failures and floor heave, low horizontal stresses can allow block fallouts. This paper summarizes the horizontal stress measurements in NFV mines and, in particular, in the West Elk Mine where their role in roof fall and floor heave failures is discussed. This experience has led to an improved use of ground support and safer mining operations at depths of 640 to 700 m.

Jan 1, 2005

By Xinzhi (Thomas) Du

"In order to monitor the overburden strata deformation over a longwall mining area in the Pittsburgh Coal Seam, three boreholes were drilled across the longwall panel. Each borehole employed multiple-point borehole extensometers (MBE) to monitor overburden strata movement during and after the longwall face passed under the study area. The longwall face in the study area was 1,428 ft wide and 4,000 ft long. The average mining height was about 7 ft. The overburden depth ranged from 550 ft to 650 ft with an average of 600 ft. The final extensometer readings indicated that overburden strata initially showed sign of movement when the longwall face was 700 ft inby the MBE. The rate of strata movement accelerated when the face was 300 ft inby MBE. When the face was directly under MBE, a sudden anchor displacement occurred, indicating rapid strata movement once under-mined gob. The readings showed insignificant strata movement after the longwall face was 400–700 ft outby MBE.INTRODUCTIONThe longwall mining method is an efficient mining method of underground mining. Surface and subsurface strata are inevitably disturbed above the longwall mined out gob. Figure 1 shows the four zones of disturbance in the overburden strata in response to longwall mining.A longwall shear cuts the coal seam and allows the immediate roof strata to cave into irregular blocky material to fill the void. This is called the caved zone. The caved zone extends from the mining horizon to six or eight times the mining height, depending on the bulk factor of each caving strata layer. The fractured zone is located above the caved zone, in which the strata breaks into regular blocks by vertical or sub-vertical fractures caused by bending forces due to the weight of the underlying strata. The surface soil and rock crack zone extends to approximately 50 ft below the surface. The surface cracking is caused by downward movement of the surface. Between the fractured zone and surface crack zone is the continuous deformation zone. The strata in this zone deforms gently without causing any major cracks that extend long enough to cut through the thickness of the strata, as in the fractured zone (Peng, 2006).The objective of this project is to provide fundamental rock mechanics research about overburden strata movement response to longwall-related activity. The findings aid in better understanding pillar stability, gas well subsidence management, hydraulic impacts, and numerical modeling."

Jan 1, 2018

By James D. Pile

Following a methane ignition in the active panel of a longwall coal mine, the affected panel was successfully isolated from the rest of the mine. This allowed for the remainder of the mine to return to regular operation, and the conventional practice of having to seal the portals for a defined period of time was avoided. After the affected panel had remained isolated for a regulatorily mandated period of time, it was reopened in preparation for longwall face recovery. As it was not possible to move the shields from their existing positions to facilitate the installation of recovery mesh prior to shield recovery, alternative methods had to be considered to stabilise the gob and minimise flushing, thereby improving operator safety. The objective of the paper is to show how stabilisation of the gob was achieved during shield recovery, thereby minimising flushing, and improving operator safety. Phenolic foam was chosen and injected from between the shields into the gob behind them. This is a technique that has been used to great effect in Germany, to a lesser extent in Australia, but not knowingly to date in the United States. To ensure nothing was left to chance and thereby guarantee the project?s success, the procedure used in Germany was employed, down to the application of equivalent hardware, which was sourced through the North American supplier.

Jan 1, 2013

By Peter Zhang

Room and pillar mining under shallow depth is usually conducted with a high extraction ratio, which leaves small pillars with a low safety factor in some old workings in abandoned mines. Pillar sloughage, squeezing or even collapse may have occurred in those old workings with small pillars, either at the time of mining or later. The conditions of the pillars in abandoned mines can affect mining above them. Subsidence fractures and abutment pressure are indications of multi-seam interaction caused by squeezing or collapse of small pillars. To mine over areas with potentially unstable small pillars, the panel layout in the upper seam should be such that multi-seam interaction can be minimized and proper roof and rib support should be installed in the influence zones. This case study presents an example of multi-seam mining above small pillars under a shallow depth of cover. Though the interburden is relatively thick and competent, interaction is still present over the influence zones. Pillar stability and multi-seam interaction analysis, numerical modeling and in-situ monitoring are presented to demonstrate how the upper seam can be mined safely over the small pillars.

Jan 1, 2014

By Anton Sroka

The dimensioning of shaft safety zones is a substantial task of mining subsidence engineering. On the one hand, the coal reserves in shaft proximity are to be mined as complete as possible, because they can be made accessible economically. On the other hand, the maintenance of the shaft operation is to be ensured at each time, since shafts represent the most important link between underground and aboveground. Regarding these two criteria, this publication presents a model for the optimization of shaft safety zones. Beyond that, extraction methods in shaft safety zones are described, in particular with consideration of minimized mining influences on the shaft.

Jan 1, 2005

By L. Mahony

This paper describes the design, construction and commissioning testing program for a laboratory facility at the School of Mining Engineering, UNSW, Australia, aimed at evaluating reinforcement tendon performance when subjected to shear loading. The project has been financially supported through the coal industry ACARP research initiative. The single failure plane design adopted in the test rig has been successful in allowing shear loading to be directly applied to fully installed (and where relevant, pre-tensioned) rock bolts. Initial results are extremely encouraging, and illustrate a significant axial component of load development as shearing takes place - particular in lower strength, softer material types. The paper also outlines future plans for use of this facility.

Jan 1, 2005

By Stephen C. Tadolini, Anand Bhagwat

"Intrinsic supports installed in mines with limited seam or mining heights have always proven to be difficult when the required support length is longer. To date, three solutions have been used to ensure that the correct length bolt is installed to achieve the required anchorage or to maintain immediate roof material: combination bolts, milled-notch bolts, and hot-notch bolts. The combination bolts use threaded sections and couples, which can be screwed together to form the required length. The primary bolt of choice, to minimize costs and achieve the desired support, has been milled- or hot-notch rebar bolts. These notches can be placed at strategic (required) locations along the bolt axis, so the bolt can be successfully bent and straightened during the installation process. However, these notches can reduce the strength of the bolting system; special reductions are detailed in ASTM F432-13 (2013). Technical advances in steel rolling and forged heading processes have led to the development of a deformed rebar bolt termed, the BORE bolt, which stands for Bendable Oval REbar. The BORE bolt can be bent at any location and straightened during the bolt installation cycle. This support exceeds the minimum designed capacities described in ASTM F432-13 and meets the yield and tensile strength requirements of a full diameter no. 6 rebar bolt. The profile and shape also reduces the resin annulus during the installation process to enhance mixing and shreds the cartridge film to help eliminate glove fingering.INTRODUCTIONThe height or depth of competent strata material, in the immediate mine roof, can be greater than the developed mine openings heights. This is especially true in coal mine openings where 50% of the minable seams in the US are less than 50 inches (132 cm). When this scenario occurs, it can be difficult to insert steel bolts in a solid single length. Figure 1 illustrates what difficulties can be experienced when a roof bolter operator is working and supporting a thin seam coal mine. There are three viable options currently available. Lengths of the bolt can be threaded and a steel coupler can be used between the sections to reach the required depth of anchorage. These systems, called “coupled bolts,” usually require a larger diameter hole to facilitate the larger coupler diameter and can be anchored with an expansion shell, resin, or a combination of both. To ensure that the coupler will develop the tensile capacity of the bolting system, required by ASTM 432-13 Standard Specifications for Roof and Rock Bolts and Accessories (2013), the threaded bars should be completely rotated and engaged into the coupler. Premature failures can occur when the threads “strip out” if not inserted completely."

Jan 1, 2018

By Yongping Wu

Roadway deformation and stress migration occur with uncertainty and randomness because of geology, tunneling and mining influence. In order to study the surrounding rock deformation and failure mechanisms in three-dimensional stress state, an air return roadway of Yuanyang Lake mine of Shenhua Ningxia Coal Industry Group Co., Ltd. was chosen as a research object. The three-dimensional model was a designed and completed experiment with a dynamic-static coupling load. The model was loaded by hydraulic cylinder, simulating the in-situ rock stress field and the induced stress field of surrounding rock. The deformation monitoring system of the roadway model was constituted by optical total stations, borehole observation instruments, acoustic emission monitoring, and stress sensors. A wealth of data was obtained through an omni observation of surface displacement, characteristics of stress distribution, and deformation and failure of surrounding model material. By acoustic-optic-electric methods, a real-time testing on physical, mechanical, and damage parameters was realized through the experimental process. The results showed that the data of deformation and failure obtained from the deformation monitoring system of the roadway were authentic, which has great significance for warning and forecasting safety hazards of surrounding rock in coal mines.

Jan 1, 2013

By Xicai Gao

With the intensification and expansion of deep coal mining, the surrounding rock stress environment becomes further deteriorated because of the complicated geological environment and powerful mining effect, so the major deformation of roadway appeared frequently. The proportions of floor heave are increasing and , the most serious problem is the floor heave of preparatory workings. The coal seam of Binchang coal area in Shaanxi province is at a depth of 621.6 ~ 817.0 m, the average thickness of the coal seam is 25 m, and the overburden and coal measure strata are the main regional aquifers and are highly permeable. The properties of water-weakening are obvious in the floor strata. The main preparatory workings or chambers were driven in the coal seam. The severe floor heave of the water chamber appeared during early mining and the amount was 180 ~ 910mm, and seriously affected the normal installation and use of the water chamber. Theoretical study and numerical simulation as well as the in-situ measurements were carried out to investigate the deformation and failure characteristic of the surrounding rock with non-support in the floor and the main reasons which caused the floor heave were determined. A new combined support technology was proposed which consists of overcutting, grouting, backfilling and invertedarch and bolt-grouting. The field monitoring showed that the cumulative convergence of the water chamber was 20mm, the maximum convergence speed is 1.2 ~ 2mm/d, the accumulative convergence of two ribs was 36mm and the maximum convergence speed is 2mm/d. The combined support technology will enhance the support intensity between the roof and floor, the two sides of the entry and improve the loading capacity of the floor effectively and the floor heave can be controlled effectively.

Jan 1, 2013

By Kevin J. Ma, John Stankus

"In order to access remote reserve areas, some U.S. coal mines have to maintain aged underground entries for a great distance. However, high humidity, warm temperature, and time dependent deterioration can cause progressive roof deterioration and unexpected roof falls can, pose a great challenge to ground control engineers. With an active belt structure in place and limited space, re-bolting becomes very costly, less effective, and, sometimes, impractical and unfeasible. To gain long-term entry stability and serviceability, operators typically rehabilitate the aged belt entries by installing standing steel set supports. In the last several years, Keystone Mining Services, LLC, (KMS) has assisted many coal mines with their belt entry rehabilitation projects, evaluated the ground condition of various aged belt entries, and designed different standing steel set support systems. This paper presents a case study of a large-scale roof fall that occurred at an aged belt entry in a mine located in an eastern coalfield, analyzes root causes of excessive deformation of square sets that were installed in an adjacent entry, evaluates the adequacy of an existing rehabilitation square set, and develops remedial recommendations for future rehabilitation practice. Based on the case study, the paper outlines design guidelines for rehabilitation steel sets that include field evaluation, engineering considerations, design assumptions, steel structural analysis, and field installation quality control. INTRODUCTION With gradual depletion of shallow coal reserves, some underground coal mines have to maintain long-term entries (belt, track, return airway, etc.) for a great distance in order to access remote coal reserve areas. However, due to high humidity, warm temperature, and aging in the belt entry, roof strata weathering and pillar degradation become more and more severe. Progressive roof deterioration poses a great challenge to ground control engineers. Pillar rib sloughs at certain locations, entry width increases in some areas, immediate roof sags, immediate roof rock falls out between bolts, existing bolts lose functionality due to corrosion, cutters develop deeper in corners, and strata separation develops deeper up into the main roof. As a result, unexpected roof falls occur in a random manner resulting in loss of production, damage of belt structure, and even injuries to underground personnel."

Jan 1, 2017

By Zach Agioutantis, Christopher Mark

"Thirty years ago, the Analysis of Longwall Pillar Stability (ALPS) inaugurated a new era in coal pillar design. ALPS was the first empirical pillar design technique to consider the abutment loads that arise from full extraction, and the first to be calibrated using an extensive database of mining case histories. ALPS was followed by the Analysis of Retreat Mining Stability (ARMPS) and the Analysis of Multiple Seam Stability (AMSS). These methods incorporated other innovations, including the Coal Mine Roof Rating (CMRR), the Mark-Bieniawski pillar strength formula, and the pressure arch loading model. They also built upon ever larger case history databases and employed more sophisticated statistical methods.Today, these empirical methods are used in nearly every underground coal mine in the US. However, the piecemeal manner in which these methods have evolved resulted in some weaknesses. For example, in certain situations, it may not be obvious which program is the best to use. Other times the results from the different programs are not entirely consistent with each other. The programs have also not been updated for several years, and some changes were necessary to keep pace with new developments in mining practice.The Analysis of Coal Pillar Stability (ACPS) now integrates all three of the older software packages into a single pillar design framework. ACPS also incorporates the latest research findings in the field of pillar design, including an expanded multiple seam case history data base and a new method to evaluate room and pillar panels containing multiple rows of pillars left in place during pillar recovery. ACPS also includes updated guidance and warnings for users and features upgraded help files and graphics.INTRODUCTIONPillar design is one of the fundamental elements of mining engineering. Pillars are necessary to control the great weight of the overburden during all phases of underground mining. Without stable pillars, ground control is impossible."

Jan 1, 2018

By Selmar A. Oliveira

"Safe mine closure is an important step in the mining lifecycle. Plans for safe and efficient closure should begin at the inception of mining. Ideally, closure occurs when the reserve has been depleted. However, when the abandonment of a mine occurs prior to the depletion of the reserve, several problems arise which need to be treated. This situation occurred at Verdinho Mine, located in the state of Santa Catarina, southern Brazil. Verdinho Mine is a coal mine that operated for more than 40 years without had backfill technologies applied. Soon before the exhaustion of the reserves, it was abandoned by the owners without proper closure. As a result, the Federal Public Ministry filed a public civil action to promote proper closure. Several parties are currently involved, including the National Department of Mineral Production (DNPM), the mining regulator of the Brazilian Government. To meet the judicial determination, a cooperation agreement was initiated between DNPM and the Federal University of Rio Grande do Sul (UFRGS) to identify and to monitor parameters which could result hazard due flooding mine, to model the various conditions to minimize the impact of flooding caused by total abandonment. Many processes must be planned and planned early in mining operations, and these processes must be performed over the life of the mine. Financial resources must be guaranteed by a specific fund fueled by operating revenues. When these resources are not properly employed, costs and technical difficulties prevent proper closure progress. If the removal of subsoil equipment, treatment and control of groundwater, regeneration of the surface, and closure of openings are not done correctly, there can be environmental, social, and stability impacts over time. To avoid this in the future, a detailed study is being performed at the Verdinho Underground Coal Mine on how to appropriately implement mine closure and monitoring procedures. This study is being conducted in response to a lawsuit filed by the Federal Public Prosecutor’s Office. INTRODUCTION The nature of the Mining Industry is such that all mining is a temporary activity, where the operational life of a mine is defined by the final project scope. The operating life of a mine lasts from a few years to several decades. Mine closures occur once the mineral resource at a working mine is exhausted, or operations are no longer profitable. Mine closure plans are required by most regulatory agencies worldwide, such as the Mineral Production National Department (DNPM) in Brazil."

Jan 1, 2017

By Syd Peng

In designing a proper roof support system, one must know the features of roof geology in advance of mining. The drilling parameters obtained during normal roof bolt installation cycle can provide a large amount of information on the roof geology when properly interpreted. It is also an economic way for identifying the geological features of the roof. This research develops a method for predicting the roof geology based on the drilling parameters obtained during roof bolting operation. From the results of a series of laboratory and underground tests, feed pressure is found to be a good indicator for identifying the voids/fractures and estimating the roof rock strength. This paper describes the method for determining quantitatively the location and the size of void/fracture and estimating the roof rock strength from the drilling parameters of roof bolter.

Jan 1, 2005

By Craig Compton

The The National Institute for Occupational Safety ane Health (NIOSH) Pittsburgh Research Laboratory (PRL) is continuing to investigate the behavior of fully grouted roof bolts in the weak roof rock of the Safety Research Coal Mine (SRCM). This paper describes the results of three studies: A series of 24 pull tests of bolts installed fully grouted and overcored to leave 12 inches of grouted bolt. The tests compared the pull-out performance of offset-head roof bolts with that of standard 518-inch bolts; A second series of 24 tests that compared the pull-out loads obtained by bolts installed with 1 R of resin (a Short Encapsulation Pull Test or SEPT) to that of fully grouted bolts overcored to leave only 12 inches of grouted bolt, and An investigation into the pressures generated during the installation of fully grouted resin bolts. All of the bolts installed and pulled were overcored and removed from the roof after the pull tests to allow inspection of the resin. The first study found that there was no significant difference in pullout load between the offset-head bolts and the standard bolts. The second study, comparing the SEPT bolts and the partially- overcored fully grouted bolts, indicated that SEPT can significantly underestimate bolt anchorage grip factor, suggesting that the SEPT is a conservative measure of actual bolt performance. Significant loss of resin to cracks in the roof was observed in the bolts overcored in the SRCM. The third study explored one possible explanation for the resin loss, high pressures generated during bolt installation. These tests employed bolts installed in strain gauged steel tubes. The results confirmed that significant pressures (greater than 4,000 psi) can be generated during bolt installation. The results of the pressure tests, combined with the observations of resin loss in bolts installed in the SRCM, suggest that under some circumstances resin loss and under-encapsulation could take place and lead to degraded bolt performance. Glove fingering was observed in all recovered bolts to various degrees. The limited comparative data suggested that the effect of glove fingering ranged from slight to moderate. Complete mixing of the resin was observed on all of the 40 bolts recovered (28 fully grouted and 12 SEPT). Australian and U.S. resins were compared and the Australian resins were observed to have much smaller catalyst compartment areas and lower resin viscosities. These differences are suggested as potential explanations for occasional resin mixing problems noted in Australian resin bolt installations.

Jan 1, 2005

By Kot F. v. Unrug

In spite of the extensive research and accumulated experience from mining operations, an appropriate pillar design remains an open issue. Due to the shrinking reserve base, present mining operations move to more challenging conditions. There are usually thinner seams and geologic conditions are often unfavorable. For instance, mine roof and floor are weak or deteriorate rapidly when exposed to moisture fluctuations in mine atmosphere. It is common that pillars of current operations are more- squat than several decades ago when the bulk of pillar research have been carried out in thicker seams. The methods of pillars calculations were developed regionally (in particular countries) to suit design needs for the most important seams, from which the majority of coal production was coming (e.g. Pittsburg or Pond Creek seams in the eastern of US). Most of the pillar formulae use similar approach by assigning weights (using constants) to the influence of coal (seam) strength and pillar widthheight ratio on its final strength. That mechanistic approach has sound theoretical base and good data supporting its validity. However, what seems to be missing is a qualification system of the mine conditions, which are outside of the data base or do not comply with the theoretical model applied in pillar strength formulae. This paper attempts to address that issue in two major categories, first when only a drill core data are available, and second during the mine development observations can be made directly on a coal seam. The composition of a coal seam is also addressed, (which often changes rapidly across the reserve), and discussed its influence on pillar's structural performance. In summary a set of practical design rules is presented.

Jan 1, 2005

By Naj Aziz

n Australia, the common method of laboratory testing of bolt for load transfer capacity determination is by short encapsulation push testing. Some concerns are raised about the validity of the test methodology, as the method does not reflect on the actual load transfer characteristics of bolt in real field situation. Thus, laboratory testes were carried out to examine the load transfer mechanisms of bolts in both the push and pull conditions. Tests were conducted by shearing a short resin encapsulated bolt out of a cylindrical steel sleeve. Three types of bolts with different surface profile configurations were tested. The study was complemented with numerical simulation of the test methods. Irrespective of bolt type the average shear load and shear stress values were found to be greater in push test, and the displacement at peak shear load was greater in pull test. The average shear stifhess values were greater in push test. The numerical simulation of the bolts provided a clear understanding of the stresses and strains generated by different bolt profiles during both the pull and pull testing process, thus allowing a better appreciation of the load transfer mechanism process.

Jan 1, 2005

By D. Bigby

The current British Standard on rock reinforcement components used in coal mining (BS7861:1996) employs the axial double embedment tensile PET) test to determine the main system load transfer performance criteria, in terms of bond strength and stiffbess. This test involves measurement of load/displacement characteristics of a tendon fully grouted into internally threaded thick-walled steel tubes. Part 1 of the Standard covers rock bolting systems and Part 2 covers birdcaged cable bolting systems. Both parts are highly prescriptive, defining a specific design of bar (AT) and cable bolt (birdcaged). In 2000, it was agreed by the UK Rockbolt Research Liaison Committee that Part 1 of the Standard should be revised to allow further industry innovation of bolts and resins. Amongst other aspects, it was recognised that the double embedment test was limited by its inability to examine load transfer between the bolt and the host rock and the UK Health and Safety Executive commissioned an RMT research project to develop a new test to replace the DET test. The new test, the Laboratory Short Encapsulation Pull (LSEP) test has now been incorporated into a draft revision of BS7861 Part1 which has been issued for industry wide consultation. In 2003, it was agreed to begin revision of Part 2 of the Standard to encompass the many types of long tendon reinforcement which were, by then, being used in the UK coal mining industry. These included flexible bolts, deformed strands and tensionable systems encapsulated with resin, cementitious grout and combinations of the two. A second RMT research project was funded by the HSE to examine adapting the Laboratory Short Encapsulation Pull Test for the revised long tendon Standard. This project is nearing completion and a revised Part 2 of the Standard is being drafted. This paper presents some of the results of the two research projects, describes the laboratory tests and acceptance criteria developed and discusses the implications of the research on improving the understanding of reinforcement performance and its characterisation. In particular it shows how the new test can reveal very different load transfer characteristics to the double embedment test, as it takes the load transfer at the holefrock wall into account.

Jan 1, 2005