Search Documents

By Mark Khinkis, Huajun Yuan, Mark Zak, Yaroslav Chudnovsky, Aleksandr Kozlov

"An afterburner for green petroleum coke calcination in electrothermal fluidized bed was designed, fabricated, installed, and tested on a pilot fluidized bed calcination furnace. The experimental set-up comprised a combustion chamber, in which fine particles and volatiles of the furnace off-gas were fully combusted, and a cooler equipped to calculate the related heat recovery and losses. Off-gas composition was analyzed to evaluate the combustion process. The energy balance confirmed the potential to recover a large part of the heat value of volatiles and fme particles from the GPC. Potential future applications of the results are discussed.IntroductionGreen petroleum coke (GPC) is an oil refining byproduct that can be used directly as solid fuel or as feedstock for the production of calcined petroleum coke [1-2]. GPC contains a high amount of volatiles and sulfur. With coke calcination, the GPC is heated to remove the volatiles and sulfur in the calciner off-gas to produce purified calcined coke, which is used in the production of graphite, electrodes, metal carburizers, and other carbon products. Currently, more than 80% of calcined coke is produced in rotary kilns or rotary hearth furnaces. These technologies provide partial heat utilization of the calcined coke to increase efficiency of the calcination process, but they also share some operating disadvantages [3]. On the other hand, coke calcination in an electrothermal fluidized bed opens up a number of potential benefits for the production enhancement while reducing the capital and operating costs.The increased usage of heavy crude oil in recent years has resulted higher sulfur content in green coke produced from oil refinery process, which requires a significant increase in the calcinations temperature and residence time [ 4]. The calorific value of the process off-gas is quite substantial and can be effectively utilized for combined heat and power (CHP) production to complement the energy demand. Waste heat recovered from the product cooling could also contribute to the overall economics of the calcination process. Preliminary estimates indicated the decrease in energy consumption by 35-50% as well as a proportional decrease in greenhouse gas emissions. So, efficiency improvement of the coke calcinations systems is attracting close attention of the researchers and engineers throughout the world."

Jan 1, 2014

By Duclerc Fernandes Parra, Washington Luiz Oliani, Christiano Gianesi Bastos Andrade, Ademar Benevolo Lugão, Danilo Marin Fermino, Francisco R. Valenzuela Diaz

This work concerns the study of the effect of discarded bond paper on the mechanical behavior of polypropylene/organophilic clay nanocomposites. A brown polycationic bentonite from the state of Paraíba, Brazil, was treated with sodium carbonate to transform it into a bentonite that swells in water and then treated with hexadecyltrimethylammonium ammonium chloride to transform it into a bentonite that swells in organic liquids. Polypropylene with 3 % polypropylene graft compatibilizer (PP-g-AM) was mixed with 1 % and 2 % by weight of discarded bond paper and with 1% and 2% by weight of organophilic clay using a twin-screw extruder. The specimens were prepared by the injection process. The clay as received and after organophilization was characterized by XRD, SEM, and capacity of swelling in water and in organic solvents. The nanocomposite specimens were characterized by XRD and thermal analysis. The mechanical behavior of the injected specimens was evaluated by strength, flexural and impact tests. The nanocomposites showed improved mechanical properties compared with the polymer without filler.

Jan 1, 2015

By S. W. Marcuson

Smelting of nickel-copper sulfide ores at Vale Inco’s Sudbury operations commenced in 1888 and the first converting plant went into operation in 1892. As the demand for nickel grew, the smelting operations expanded and by the 1960’s the Copper Cliff Smelter featured the longest converter aisle in the world with space for nineteen Peirce-Smith converters. During this long period, different converting techniques and vessels were employed. The evolution of converting is reviewed with special emphasis on the modifications made to the Peirce-Smith vessel to accommodate the metallurgical and process needs of the changing times.

Jan 1, 2009

By J. L. Johnson

The U.S. Department of the Interior, Bureau of Mines, investigated recovery of concentrates containing tin, tantalum, and niobium from the Kougarok deposit on the Seward Peninsula, AK. To date, 25 million lb of tin has been delineated in occurrences containing 0.36 to 1.32 pct Sn, and the resource potential is estimated to be as high as 25 million short tons at average grades of 0.75 pct Sn, 0.025 pct Ta, and 0,025 pct Nb. Deslimed ore was concentrated to 54 pct Sn, 0.3 pct Ta, and 0.3 pct Nb, with recoveries of 74 pct Sn and 44 pct Ta/Nb using a Humphrey's* spiral followed by a Deister shaking table. Tin values in the slimes were upgraded to a 5-pct-Sn concentrate using a Bartles-Mozley separator followed by flotation. The 5- pct-Sn was further upgraded by fuming to give a concentrate containing approximately 60 pct Sn. The recovery of the two products combined was 80 pct Sn and 46 pct Ta/Nb, A flowsheet with mill-design parameters resulted from the metallurgical testing. An economic analysis was made based on the proposed process.

Jan 1, 1990

By Qian Li, Haiyan Leng, Kuo-Chih Chou, Haoyuan Xiao, Zhigang Yu

Magnesium borohydride and Magnesium alanate were synthesized by mechanochemical metathesis reaction. The thermal decomposition behaviors of Mg(BH4)2-nMg(AlH4)2(n=0.5,1) systems were investigated as potential hydrogen storage materials. The results showed that the systems started to desorb H2 at 120 ℃ and desorbed 3.9 wt. and 4.9 wt.% H2 below 300 ℃ when n equals 0.5 and 1, respectively, while individual Mg(BH4)2 started to desorb H2 at 250 ℃ and desorbed only 0.82 wt.% H2. Because of the exist of the Mg(AlH4)2, the isothermal desorption kinetics of Mg(BH4)2 in the Mg(BH4)2-0.5Mg(AlH4)2 systems was 50% faster than that of pristine Mg(BH4)2. In addition, the re-hydrogenation rates also increased 49.4% and 37.9%.

Jan 1, 2015

By Ruhi Bux, Akshay Verma, Mohini Saxena, P. Asokan

"Due to the colossal increment in the industrialization, the generation of wastes gathered as a result of different extraction, benefaction and generation processes is having an alarming problem for waste disposal. The best and most acceptable way is to use the waste in accordance to its potential for the generation of high value lucrative composite goods. The study in this paper elucidates the potential of several industrial wastes like fly ash, red mud and marble slurry dust for the production of different wood substitute products like doors, windows, roofing sheets and instant houses for the rehabilitation on the sites of catastrophes. Wastes were initially characterized for the physical, chemical and mineralogical properties and then used in different formulations with binder like Polymer along with natural fiber like Jute to intensify the physical as well as mechanical properties of the resultant composite. The study also reveals that these composites have better mechanical properties than the available ones like teak, medium density board, Rice husk board etc. Also, the fly ash and red mud composites have better mechanical properties than marble slurry based composites. The results fosters the implementation of natural fiber with the industrial waste in the generation of eco-friendly and non-hazardous composites.IntroductionOver the last few decades, there has been a tremendous increase in the generation of industrial wastes gathered as a result of various extractions, benefaction and generation processes. The condition worsens even, when it comes to high quantum generated wastes like Fly ash, Red mud and Marble slurry dust. The primordial motif behind the incorporation of industrial wastes as filler in the development of composites is primarily composed of two main objectives; Firstly waste management, the colossal waste dissemination in the environment has disturbed the ecological balance by polluting land, surface water, ground water, air, natural resources and even disturbing the public health [1]. Secondly, to act as a perfect substitute for the conventionally existing building materials, this will aid in dwelling places to many with the least incorporation of exhaustive natural resources as woods quid pro quo."

Jan 1, 2008

By V. V. Khristenko, V. I. Dubodelov, V. A. Seredenko, B. A. Kyryyevsky, H. V. Seredenko

"During the last decades investigators of many countries shows an increased interest to alloys which are characterized by miscibility gap in a liquid state. It is connected with essential possibilities of control of structurization in such alloys because of the melt at certain temperature parameters is · emulsion with disperse phase inclusions. These ensure essential influence ·on structurizations.The certain inclusions can play a role of lubrication ensuring ""wearless"" process. The sizes of inclusions of this phase can be rather large proportional to sizes of strengthening phase (up to 1000 nm). Other inclusions ensure process of strengthening of a main material. In this case requests to a dispersibility character of distribution and structure of such inclusions are much higher.The multicomponent alloys of system of copper - (Fe - Cr - C)- alloy concern to the number of advanced compositions. The copper alloys with structure of a type of a ""frozen emulsion"" in which strengthening phase· is a chromium pig-iron are characterized by high thermal stability in the extreme operating conditions. The mechanism of inclusions forming is emulsifying of a melt in miscibility gap at temperatures close to temperature of binodal under superimposition of external effects.The main complexity of producing of ware from such alloys is .a providing in their structure of necessary dispersible inclusions uniformly distributed all over the volume. Thanks to a selective action of electromagnetic fields on liquid phases with various electroconductivity relative velocity of phases is created and is regulated the ratio of their ""apparent"" specific gravity is changed. Excitation of pulsing force effects with the certain frequency on interphase surface allow actively to influence on process of a dispersion of a liquid metal medium."

Jan 1, 2000

By F. Kongoli

A computerized thermophysicochemical database is being developed for various processes involved in nickel smelting and converting. This database includes optimized models for slag, matte, liquid and solid alloys in the multicomponent system(s) as applied to batch and continuous nickel smelting and converting processes. This database can be used to quantify the multicomponent and multiphase slag/matte/alloy/gas equilibria, liquidus and solidus surface, tie-lines, solubility and/or losses of nickel and other components in the slag, distribution coefficients, components activities, heat and mass balance, etc. The database also includes optimized models for the viscosity of the slags associated with any of the above processes. Both databases are coupled and this constitutes a very effective method to quantify the effect of each component on several parameters of the smelting and converting processes and to diffuse the confusion that exists in the literature. Several application examples have been given to demonstrate the usefulness of this database for quantitative prediction of the thermophysicochemical properties of the phases involved in actual or developing processes, even in the areas where experiments are difficult or impossible. The considerable cost reduction that results ftom the use of this database as compared to other methods in the improvement of existing technologies or in the development of new ones is discussed along with continuing new developments of this database.

Jan 1, 2002

By Masatsugu Morimitsu, Tian Zhang

"This paper presents a novel anode for oxygen evolution in acidic aqueous solutions to produce non-ferrous metals by electrowinning. The method to prepare the anode was thermal decomposition of a precursor solution, and the obtained anode consisted of Ru02-based oxide catalytic layers formed on a titanium substrate, in which the catalytic layer contains nano-oxide particles as the active component. The oxygen evolution potential was lower than amorphous lr02-Ta20s coated titanium anodes so that the cell voltage of electrowinning was further reduced with the amorphous Ru02-based electrode.IntroductionElectrowinning (EW) is used to produce high purity of non-ferrous metals, and the primary metal production of copper, zinc, nickel, and cobalt by EW consumes huge electric energy worldwide, which tends to increase with increasing demand of such metals. The reduction of electric energy consumption is a significant issue for electrowinning industry, which means that the cell voltage reduction is needed to realize more energy-efficient EW processes. Another issue is also indicated from environmental perspectives; i.e., an improvement in EW plant environment by eliminating hazardous byproducts and wastes. Such byproducts and wastes include lead oxide, manganese oxide, and acid mist.We have been developing the anodes for energy-efficient and environmentally friendly electrowinning processes [ 1-11]. The development has been successfully done with the invention of the smart anode, MSA TM (Morimitsu Smart Anode) [ 1-5], which has low polarization for the main reaction and high polarization for the side reaction, in which the main reaction is oxygen or chlorine evolution, while the side reaction is the anodic deposition of each or both of lead oxide, manganese oxide, and cobalt oxide. The anode consists of a valve metal substrate coated with amorphous or less crystalline oxide catalytic layers. One of the typical examples of such oxides is amorphous lr02-Ta20s, and the substrate is normally titanium plate or mesh. The most important point of the oxide is that the amorphization or less crystallinity induce the increase in the active surface area only to the main reaction, not to the side reaction, thereby the polarization of the main reaction being reduced.In this paper, we present the smart anode consisting of RuO2-based catalyst formed on titanium substrates for oxygen evolution in electrowinning. The preparation, characterization, and polarization behaviors of the anodes are shown, and the cell voltage data for zinc or copper electrowinning using the anodes are also presented."

Jan 1, 2012

By J. Pesl, U. Kemey, F. Sauert

"The CONTOP® smelting cyclone is a water-cooled, upright, high-intensity smelting reactor. The technology for the reactor was initially developed and brought into industrial-scale operation in the area of non-ferrous metallurgy. The two largest smelting cyclones were built with a capacity of 32 tons per hour of copper concentrate mix.The newest industrial CONTOP® plant treats up to five tons per hour of zinc-bearing residues including EAF dust. The highly concentrated zinc-lead oxide produced is sold to the zinc industry. The slag fulfills the leaching criteria and is used in waterway construction. The heat transferred to the cyclone cooling system and the off-gas boiler produces steam from which power is generated in a turbine.V AI has erected a new CONTOP® demonstration plant at MEFOS, Lulea, Sweden. A zinc volatilization rate of 90% was achieved during hot commissioning with Swedish EAF dust.Treatment costs in the range of 85 to 100 EUR per ton were estimated in a feasibility study on the treatment of 73,000 and 57 ,000 tons EAF dust for a group of steelmaking mills in Southern Europe."

Jan 1, 2000

By K. C. Mills, P. N. Quested, A. P. Day, R. F. Brooks

"Methods have been developed to measure the physical properties of molten materials relevant to the fluid flow in high temperature processes. Data for the densities, viscosities and surface tensions of Al-, Ni- and Fe-based alloys are compared with (i) values for the pure metals and (ii) estimated values obtained from models making use of chemical composition of the alloy. Experimental values for metallurgical slags are also given and compared with estimated values.1 IntroductionPhysical property data has proved very useful in improving process control and product quality. For instance, in the continuous casting of steel the viscosity (TJ) of the mould flux is important since it determines (i) the optimum casting conditions, nVc = 2.5±1 dPas (m min-1) where V c is the casting speed and (ii) the level of slag entrapment (which leads to inclusions) in the metal. Thus data for properties like viscosity are exceedingly useful in understanding the process and the problems encountered and the causes of defects and problems.Another interesting development which has helped to increase our knowledge of processes and improve process control and product quality is the development of mathematical models of the fluid and heat flow in the process. These models have been developed to the stage where one of the prime requirements is for good physical property data for the industrial materials involved. Recently, Oxley [1] has shown that the use of reliable, experimental, property values for the commercial alloy in a commercial software package produced a significant improvement in the prediction of casting defects. Thus reliable property data are required for liquid metals but also for (i) liquid slags since many processes involve the use of a slag to refine and protect the metal or to lubricate the mould and (ii) refractories, sand and investment moulds."

Jan 1, 1999

By S. Abe

Various copper anodes to be electrorefined were subjected to a heat treatment comprising annealing at a temperature in the range of 700 °c to 1,000 °c followed by a slow cooling preferably on the order of about 150 °c, and using these heat treated anodes , a series of dissolution experiments were conducted under conventional electrorefining conditions. The results obtained have indicated that the above annealing/slow cooling process dramatically improves the dissolution activity regardless of the type of anodes. As an example, passivation times of l to 3 minutes in a standard test have been increased to more than 80 minutes by this innovated heat treatment. Other advantages sterning from the improved anodic activity include reduced electrical short circuiting which results in substantial labor effort in the tankhouse, reduced energy requirement, and reduced cost of processing anode slimes because the amount of anode slimes is reduced. In addition, this process gives rise to a dramatic change in the nature of anode slime layer formed in such a way that a comparable final cathode copper product can be achieved even from high-impurity copper starting material.

Jan 1, 1987

By Yoshihiko Maeda

"Although Japanese mining industry once had been a polluter of toxic heavy metals and gasses, it has been struggling for improvement of environment at mining and smelting facilities under the strict Japanese regulations. Through these efforts, the industry has developed various environmental technologies to be applied in other industries and society.Recycling of metal scraps, for example, has been conducted at smelting facilities. Treatment of hazardous waste, cleanup of contaminated soil and management of landfill are other examples of application of mining and smelting technologies and facilities. In accordance with the worldwide environmental concerns, the industry has become one of the leading industries to promote ""Sustainable Development"", and it is expected further contribution in reducing various environmental burdens to earth by utilizing its mining and smelting technologies and facilities. Some of the examples of these applications are presented in this paper.IntroductionDowa Mining Co., Ltd., established in 1984, is known as one of the ~op Japanese producer of nonferrous metals. Base on its special expertise in the mining and smelting of complex ores, it has expanded its business areas to downstream activities ranging from highly purified metals and alloys, electronics materials, chemicals and related various businesses. Dowa Mining now is becoming more active in the field of waste treatment and recycling.Dowa Mining had operated some mines until 1980th, located at the western part and northern part of Honshuu Island in Japan; the former is pyrite mine while the later is ""Black Ore"" mine,· a complex sulfide ore composed of high grade of copper,· silver, lead and zinc. However, due to the strong yen began in1985; Dowa Mining closed its mining operation in 1994, and has sifted to mining operations in Mexico."

Jan 1, 2000

By Y. Huang, P. B. Prangnell

"An Al-0.1Mg alloy was firstly deformed at room temperature by ECAE to a true strain of 10, where a steady state deformation was established and further processing had little effect on grain refinement. The ECAE samples, with an average grain size of ~0.55µm, were then compressed in a channel die at 77K- 473K to various reductions. Microstructures were characterized by electron backscatter imaging and EBSD in a FEGSEM. Grain refinement to the ECAE submicron structure occurred during deformation at cryogenic temperatures of 77 – 213K, whereas coarsening took place during deformation at elevated temperatures. A steady state deformation was observed at all temperatures where a constant grain structure was developed and maintained upon further straining due to dynamic recovery. The mechanisms of dynamic recovery during steady state deformation at cryogenic temperatures are discussed.IntroductionSevere deformation processing (SDP) has been successfully used to produce submicron grain structures, and in some cases nano-scale crystallite sizes, in a wide range of alloys. However, the rate of grain refinement becomes increasingly inefficient at high strains as a steady state grain structure is approached [1-3]. Steady-state grain sizes have also been reported in other ultra-high strain deformation processes, like cryogenic ball-milling [4]. There is thus a minimum grain size achievable in a material by a given SPD process under constant deformation conditions.It is well documented that a steady state subgrain size is observed in warm deformation of metals due to dynamic recovery (e.g. [5]). In severely deformed alloys a constant grain size at ultra-high strains has similarly been attributed to dynamic recovery [1-3]. Mechanisms have been proposed, for rapid deformation induced grain growth including stress driven boundary migration and breakaway from solute pinning [2]. However, as pointed out by Humphreys et al. [2] the restoration processes are currently poorly understood, particularly at low temperatures, where the boundary migration rates required to maintain a constant grain size are orders of magnitude higher than can be satisfactory explained from diffusion controlled migration. Similar to the subgrain size, the steady state grain size obtained during SDP is generally related to the temperature compensated strain rate [2, 6]. Thermally activated restoration processes are thus expected to be suppressed by lowering the deformation temperature and a smaller steady state grain size can be achieved."

Jan 1, 2012

By Adriana de Aquino Soeiro da Silva, Joao Alves Sampaioa, Luiz Carlos Bertolino, Francisco Manoel Garrido, Marta Eloisa Medeiros

"Brazil has a large agricultural potential and its production success is related to the chemicaland physical soil characteristics. Therefore, the demand in the use of a great quantity offertilizers to compensate the low amount of nutrients in the soil includes about 40% of foodproduction costs. In order to develop economical alternatives to traditional fertilizers, rockswith potential use in agriculture will be studied. In this work the potassium rock, a greensandslate, will be chemically and structurally characterized for the development of a potassiumthermophosphate. This alternative fertilizer will be obtained based on a fusion of a ponderedmixture of potassium, magnesium and phosphate rocks to be applied in the Brazilianagriculture. Preliminary characterization results indicate that the greensand slate presents ahigh percentage of glauconite, quartz and micas.Keywords: Potassium thermophosphate, alternative fertilizers, greensand slate.IntroductionBrazil has a great agricultural potential and its production success is closely related to thesoil's chemical and physical characteristics. However, the country's soils present lownutrients content and high acidity due to weather conditions. Thus, the use of a high amountof fertilizers makes up for the soils' lack of nutrients and accounts for 40% of food productioncosts. Therefore, research on obtaining new alternative fertilizers is a constant worry due tothe increase on food demand [ 1].The lack of raw material for the preparation of NPK fertilizers in Brazil is a concern and theissue of potassium fertilizers a priority. Such a fact is because in 2008 only 608.000 tons ofKCl were produced, corresponding to just 10% of the Brazilian necessity. Thus, the use ofrocks as agricultural nutrients can contribute to reduce the need for industrial fertilizers.This way, the development of a new agricultural raw material originated from a rock thatalready exists in the country's soil is of great importance for the mineral and agriculturalsectors."

Jan 1, 2011

By C. Koopman

During the production of phosphoric acid from phosphate ore and sulfuric acid, large amounts of calcium sulfate are formed, in which impurities from the feedstock are incorporated. To use the calcium sulfate in, for example, the building industry, a lower concentration of impurities is desired. Mercury, copper, lead, and cadmium were extracted from clear industrial recrystallization acid (0.8-3.9 mol/kg H3PO4, 0.2-0:5 mol/kg H2SO4) by supported solvent extraction with the extracting agent Cyanex 302 in kerosene in a transverse flow hollow fiber module. The permeability for the mercury ion was 1.4.10-6 m/s, whereas that for the copper ion was calculated to be 1.5.10 m/s. Cadmium, lead, and copper were extracted during the recrystallization of calcium sulfate hemihydrate to dihydrate, an existing step within the ,phosphoric acid production process, by solvent extraction with the same extracting agent. The concentrations of cadmium and zinc in the newly formed calcium sulfate were proven to be decreased. Unfortunately, concentrations of mercury and lead were too low for analysis.

Jan 1, 1999

By N. A. Barcza

DC plasma-arc technology using a hollow graphite electrode (cathode) has been successfully implemented in the primary metallurgical industry in South Africa up to the 30 MW scale. Mintek has applied its expertise base, established over the past fifteen years, to testing the treatment of metallurgical wastes such as carbon- and stainless-steel plant dusts, lead- and zinc-containing slags, and residues from the base-metal industry. Favourable results have been achieved, and disposable products were produced. The evaluation of numerous wastes indicates that recovery of zinc as metal gives the best economic return from these sources. Direct recovery via a splash condenser or electrolytic zinc extraction from fume are the two preferred alternatives under review. In both instances dehalogenation is an important issue, but can be achieved by suitable treatment processes. The Enviroplas technology provides a flexible, commercially viable approach to the treatment of a wide variety of wastes. Mintek, together with its associate Pyromet CC, are installing a plasma- arc pilot-plant facility with both an ISP lead-splash condenser of about 5 t/d condensed zinc capacity and a combustion chamber to burn zinc vapour to zinc oxide. This will demonstrate the suitability of the Enviroplas technology for treating specific metallurgical wastes, so that customized industrial plants can be engineered based on large-scale testwork.

Jan 1, 1994

By P. M. Swash

This paper reviews the application of some mineralogical techniques in the evaluation of the Uitkomst Ni-Cu deposit, South Africa. The low grade of the ore necessitates detailed and representative characterisation in order to establish the prospects viability. The relevant mineralogical information is generated by using optical microscopy, magnetic and heavy liquid . separations, XRD. SEM and EMPA. Methods used are briefly reviewed. The cost savings and metallurgical understanding that is provided by the mineralogical work is described especially with regard to milling, flotation and the presence of by-products (PGMs and chromite).

Jan 1, 1991

By Xiao-dong Xiang, Hong-bo Jin, Ming-sheng He, Huo-guo Pang, Can-hua Li

The specification of the steel slag aggregate will be mutated if the ag- gregate is prepared by a single type crusher. The specification stability of the steel slag improved significantly when the jaw crusher and the cone-crusher are com- binedinthecrushingprocess.Thecombinationofthecrusherandscreenisapplied to produce steel slag aggregate while the roller washing process for removing the dustfromthesurfaceofaggregate.Apilotproductionlinehasbeenestablishedby this technology. The specification stability and the road performance indicators of thesteelslagaggregateshavebeengreatlyimprovedbythispilotproductionlineas compared with the traditional production line. The particulate of the steel slag aggregate is decreased by 81% compared to the traditional line. (cid:1) (cid:1)

Mar 1, 2018

By K. S. Barros, D. C. R. Espinosa, J. A. S. Tenório

Over the past several decades, electrodialysis membranes have been employed for the removal of metals from galvanizing industry effluents. However, for its technical viability, it is useful to know some properties of the system to avoid, for example, precipitation of inorganic salts, destruction of the membrane and an increase in the energy consumption. The scope of the present study is to use chronopotentiometry to determine limiting current densities, transition times and resistances of the cationic membrane HDX 100 using a synthesized solution of the galvanizing industry effluent prepared with copper sulfate and sulfuric acid in different concentrations: 0.1, 0.5 and 1.0 g/L of Cu +2. The current-voltage and chronopotentiometric curves obtained have clearly defined regions and it was verified that the Cu+2 concentration causes a significant increase in the limiting current densities and in transition times. However, a high decrease in resistance occurred because at the highest concentrations, it is more difficult to reach the zero concentration value at the membrane surface. Besides, the pH increase causes a significant decrease in the limiting current density and in the transport number, but a slight increase in the resistance due to the presence of hydrogen. The results obtained confirm that the chronopotentiometry method is a valuable tool to determine membrane properties.

Mar 1, 2017