Search Documents

TiO2 and Ti/TiO2 thin films were deposited on a quartz substrate by laser ablation of Ti02 and Ti targets using Nd:YAG pulsed laser. After sulfurization of the Ti02 film in H2S or CS2 gas at 1273 K for 1 hour, the surface atomic structure was changed. Furthermore, the Ti/TiO2 film was successfully prepared by the subsequent ablation of Ti and TiO2 targets. The morphology and structure of the films were characterized by XRD, XPS and AFM analyses.

Jan 1, 2003

By Günter Petzow, Hans Leo Lukas, Hans Jürgen Seifert

"The CALPHAD method (CALculation of PHAse Diagrams) has been extensively developed in the last 25 years and became a useful tool in materials science. Thermodynamic descriptions for the functions of state of unary, binary and ternary phases are derived by the optimization of phase diagrams. These functions are stored in computerized thermochemical databases and can be combined to extrapolate to multi component systems. Depending on special demand, the actually most advantagous presentations of the calculated results can be chosen: tables or in a clear graphical form as phase diagrams, phase amount diagrams or volatility diagrams. The method will be desribed by the system Ti-Si-C-N-O including the ceramic subsystem Si3N4-SiC-TiCi,N1_1,-C-N-O which is very important for the development of ceramic composites. The calculations give the thermodynamic stabilities of the condensed phases as function of temperature, concentration and partial pressure of different gas species. Adjusting the sintering conditions to these results the formation of unfavourable compounds or liquid phases can be suppressed.IntroductionThe CALculation of PHAse Diagrams (CALPHAD-method) of multicomponent systems provides the possibility to plan experiments very efficiently and avoid the experimental trial and error approach for the development of materials. The main problem for best use of calculated results is their interpretation with regard to the specific applications under consideration. Tables give the exact quantitative data for the treated phenomena. However, most important to make best use of these thermodynamic data is their graphical representation especially designed for the solution of specific problems, scientific as well as application oriented. Only well chosen graphical representations support a comprehensive understanding of the thermodynamic interrelationships and the transfer to the problem."

Jan 1, 1996

By Daniel Hoffman, Katerina Aifantis, Ibrahim Miskioglu, Jaroslaw Drelich

"A new method to determine the elastic modulus of a material using the atomic force microscope (AFM) has been proposed by Tang et al. (Nanotechnology 2008, 19, 495713). This method models the cantilever and the sample as two springs in a series. The ratio of the cantilever spring constant (k) to diameter of the tip (2a) is treated in the model as one parameter (a=k/2a). The value of a, along with the cantilever sensitivity, are determined on two reference samples with known mechanical properties and then used to find the elastic modulus of an unknown sample. To determine the reliability and accuracy of this technique it was tested on several polymers. Traditional depth-sensing nanoindentation was preformed for comparison. Using both methods, the elastic modulus of the polymers tested was calculated. The elastic modulus values from the AFM were within ±(5-20)% of the nanoindenter results.IntroductionThe atomic force microscope (AFM) has proven to be a useful tool for characterizing materials on the micro- to nano-scale. The most common use of AFM is to image and measure the topography of the sample surface, but AFM has also been used to characterize the mechanical properties of materials [1-3]. With AFM's ability to scan the sample surface, features of interest can be found and indented. It provides an advantage over traditional nanoindenters that use optical microscopes and thus cannot resolve nano-scale features. This makes AFM a useful tool for characterizing materials on the nano-scale."

Jan 1, 2011

By Yoshisada Michiura, Junko Umeda, Katsuyoshi Kondoh

Rice husks or straws, one of the main agricultural wastes in South-east Asia, have a large possibility to be employed as usefully renewable resources to produce energy and high-purity silica (SiO2), because they consist of about 70% organics such as cellulose or hemi-cellulose, and 20% amorphous SiO2. The former is utilized as bio-mass energy; for example, thermal or electric energy, and bio-mass ethanol. High-purity silica can be used as raw materials in the industrial uses. It would be possible to extract silica elements from rice husks and straws by burning them in air because their main contents are organics. In the previous studies, a strong acid leaching treatment on rice husks before burning was carried out by using H2SO4, HCl and HNO3 to prepare high-purity silica materials. This was available to accelerate the hydrolysis of celluloses and hemicelluloses contained in rice husks, and remove the above metallic impurities. A strong acid leaching treatment, however, is significantly hazardous to environment and human life, and causes an increase of the process cost. In this study, the environmentally benign, harmless to human and economically effective process to produce high-purity amorphous SiO2 materials from rice husks has been established without using strong acids. From a viewpoint of the harmless influence on human body, the carboxylic acids were used in the leaching treatment on rice husks. TG-DTA measurement and GCMS analysis indicated that the leaching was effective for the hydrolysis of celluloses and hemicelluloses contained in rice husks at 473K~873K, which produced the same results in using the conventional sulfuric acid. The metallic impurities could be also removed from the husks via a chelate reaction between carboxyl groups (-COOH) and the metal elements. In particular, it was clarified that cadmium (Cd) were completely removed from rice straws by this reaction. Concerning the burning conditions of rice husks after the acid leaching, it was necessary to supply a suitable amount of air to completely combust organics; for example it required air supplement of 50 ml/min. or more. The burning temperature should be less than 1273K to obtain amorphous structured silica. High-purity amorphous silica materials with 99% or more were prepared from rich husks by applying the citric acid leaching treatment and burning process at 1073K in air.

Jan 1, 2008

By Ali Tabeshian, Ragnhild E. Aune, Reza Beheshti

Today’s lithium-ion batteries (LiBs) are found in more than half of the hybrid-electric and plug-in hybrid vehicles on the marked, all-electric vehicles, and nearly all consumer electronics. As a result, recycling of LiBs will be a strategic necessity in the near future. In the present study, the feasibility of application of conventional aluminum recycling process (secondary aluminum production) as a suitable process for treatment of LiBs was studied. The overall idea is to recover aluminum, copper and lithium from a mixed waste stream of LiBs and aluminum scrap. A two-stage process, consisting of a preheating step and a melting step, were tested on cell phone batteries mixed with pure aluminum in a ratio 1:10 and the distribution of elements between the metal phase and the slag phase evaluated. The obtained results are compared and discussed based on the thermodynamic calculated by the use of the FactSage™ software version

Mar 1, 2017

By Maurizio Marezio Bertini

Ammonia - ammonium sulfate solutions were sparged in a glass reactor with a SO2/O2 gas mixture (2% SO2 and 98% O2) to leach copper from pure chalcopyrite and chalcopyrite concentrate. The SO2/O2 mixture produces higher and faster extractions than O2 by itself. The effect of temperature, particle size and free ammonia concentration was investigated. The fastest and highest recoveries were obtained at 80 oC from a chalcopyrite concentrate with a d80equal to 13 m, with about 83 gpl free ammonia, an average pH equal to 8.75 and a stirring speed of 500 rpm. The extraction process was controlled by diffusion through a product layer, according to the shrinking core model, with an activation energy of 41 kJ/mole.

Jan 1, 2003

By Emilia Visileanu, Eftalea Carpus

"Due to the demographic explosion and development without precedent of the consumer society, the capacity to destroy the ecological balance the entire planet life depends on, acquire new dimensions. In this context new approaches on society development are imposing as well as special responsibilities for stopping and preventing Earth destruction and repairing the damage already done. The zero waste is a call to action that has as an aim the changing of current mentality of human society. ”take, use, throw away”. The zero waste is a policy, a way, an aim and represents a new approach planned for the XXI century that include the resources preservation principles, pollution reducing, increasing of the opportunities to create new work places and providing the highest degree of the.1. INTRODUCTIONThe zero waste is a call to action that has as an aim the changing of current mentality of human society. ”take, use, throw away”. The zero waste is a policy, a way, an aim and represents a new approach planned for the XXI century that include the resources preservation principles, pollution reducing, increasing of the opportunities to create new work places and providing the highest degree of the economy stability.2. ECOLOGICAL CONCEPTSA long-living Romania means:The closing of the production cycles, by waste reusing and recycling; the reducing of the use of fossil fuel; the improving of the material qualities, for extending the economical life of the products made by these materials; the reducing of the transport traffic.In this context, ecology, the star science with the ability to conserving and renewal of the environment is making its way, having the following principles:•,everything is bind by everything – is referring to the importance which the environment has for a great number of allied fields;•,everything leads to somewhere – the principle of the indestructible property of material (in nature, there must not exist wastes);•,nature does it the best – ecology becomes the responsible science with the governing of the strategic laws between man and nature, man takes advantage of the natural resources which he cannot create by himself and nature must feel guarded and not destroyed by this alliance;•,nothing is for free – the polluter pays.The protection of the natural environment means:•, its strong knowledge and that of the interactions between the social economic system and the natural system, the foreseen of the most close and most distant consequences of these interactions;•,the rational usage with maximum economical character of the natural resources not depending on their origin;•,preventing and direct fighting against as well on the degradation of the environment caused by man, as on those produced by natural causes;•,the ability to harmonize immediate interest of the human society on long and permanent term, using the natural factors of the environment."

Jan 1, 2008

By R. Hammen

Processes are needed to rapidly and cost-effectively produce highly pure lithium salts for the rechargeable battery sector. Lithium purification is a chemical engineering challenge, due to the low concentration of lithium compared to sodium, potassium, magnesium, calcium, and transition metal ions commonly occurring in lithium brine resources. We describe a Solid Phase Extraction (SPE) process that rejects sodium and potassium, while binding lithium and other higher valent ions. Lithium is then harvested by selective displacement from the SPE column. The rapid equilibration kinetics of SPE composites enables these ion separations to occur in a small SPE column and in one column stage. The chemical parameters of the process are described.

By Patricio Ruz, Gabriel Riveros, Carolina Ramirez, Andrzej Warczok, Rober Treimer

"Continuous converting of copper matte produces slag with high cuprous oxide content. The corrosion of chrome-magnesite refractories with slag of high cuprous oxide content is a major problem. Properties of olivine type of slag make the slag very attractive for matte smelting and converting.Analysis of phenomena determining the slag infiltration into the porosity of a refractory and dissolution of refractory components in the slag allowed for better understanding of the mechanisms of refractory destruction.The results of laboratory scale tests of the olivine slag infiltration into open porosity and corrosion showed dominating effects of slag temperature and cuprous oxide content. The optical and X-ray examination of slag samples permitted the definition of the mechanism of formation of new phases and refractory deterioration. 71"

Jan 1, 2009

By R. E. Brewer

Pilot scale flotation tests were conducted with a l?ft-diam column at the Barrick Resources (USA) Mercur mine, Tooele County, UT, to scavenge unleached (0.01 to 0.018 oz/st) gold values from the tailings of a carbon-in-leach (CIL) circuit. The optimal recovery was 35 pct of the unamenable-to-leaching gold, at a grade of 0.353 ounces of gold per short ton, using a mixture of dithiophosphate, xanthate, and diesel fuel as a collector. This was achieved by floating approximately 1.6 wt pet of the CIL tailings. The gold values are believed to be contained in arsenic-bearing minerals, attrited carbon, and carbonaceous material in the ore. Redox potentials were measured with a gold electrode during the conditioning stage prior to flotation. The correlation between flotation recovery and redox potential values could be used to control reagent additions. Treatment of a previously leached and weathered tailings material, averaging about 0.055 ounces of gold per short ton, was also investigated. The tailings were first water leached at approximately 60? C, and the water-leached tailings, containing approximately 0.03 ounces of gold per short ton, were then fed to the column flotation unit. The effects of pH' and sodium sulfide addition on gold flotation recovery and redox potentials were examined. Maximum gold flotation recovery, 36 pct, was achieved at pH 8,5 with a sodium sulfide addition of 0.18 Ib/st. Overall gold recovery by leaching and flotation was in the range of 70 to 80 pet.

Jan 1, 1989

By John Wallace

"Monitoring compound semiconductor crystal growth using multifrequency eddy currents for sensing illustrates some of the extreme problems of measurement and interpretation that are not often seen in metallic systems. Using sensor arrays and scanning sensors have produced a qualitative and quantitative understanding of some of the high temperature electrical conductivity mechanisms in several compound systems. A detailed review of the CdTe/CdZnTe data is presented showing some of the complexity in the data as opposed to what is found in elemental semiconductors.HistoryThe most common goal in the use of eddy current measurement in crystal growth is to deter-mine the curvature of the liquid solid interface during growth to test if the heat transfer estimates of the thermal design were adequate for single crystal growth[l]. This aim could be met but represented only a small fraction of the data that was produced observing a growth cycle. A secondary consideration was what could be discovered in the recorded data about the growth and subsequent heat treatment as the boule cooled. This is usually a more difficult task because a crystal growth process is not a controlled experiment so much as a process that continually sees modification. Using a sensor arrays or a scanning loop has produced a qualitative and quantitative basis for understanding some of the high temperature electrical conductivity mechanisms. The implication of the these measurements of electrical conductivity variations are important in that they reflect the complex defect states that will occur on cooling and heat treatment following crystal growth. In contrast to the complex behavior of the conductivity of these compound semiconductors in the solid and liquid state we have the very well characterized system silicon to compare. Initially the interest on using eddy currents to monitor compound semiconductors came from G. Westphal at the Texas; Instruments Company in 1987 to monitor aspects of growth and compounding of GaAs. This was followed by work on solution growth of HgCdTe with D. Witter. The initial interest in the use of eddy cur-rents for monitoring CdTe crystal growth came from Prof. Wilcox at Clarkson University in the practical interest to determine and control the crystal interface curvature during vertical brigdeman growth. The first actual work was done by one of his former students. G. Neuge-bauer at the II-VI Corporation which was carried on by G. Rosen at Clarkson and R. Shetty at II-VI Corporation and with A. Socha at Johnson-Matthey Electronics. The work on CdTe extends over four years and yielded sufficient data to allow one to evaluate the utility of the information produced as compared to what could be obtained from monitoring an elemental semiconductor such as silicon."

Jan 1, 1997

By R. Padilla

In most of the Chilean copper and gold concentrates, arsenic is present mainly as enargite, Cu3AsS4, which at the conventional roasting or smelting temperatures decomposes liberating arsenic as gaseous compounds. The objective of this investigation was to study the decomposition reaction of enargite in an inert atmosphere in the range of 500 °C - 750°C. The results obtained indicated that the decomposition begins at about 525 °C. Two distinct regions in the temperature dependence of the decomposition rate were observed: a low temperature region between 525 °C to 650°C and a high temperature region between 650 °C to 725 °C. The X-ray diffraction analysis suggests that the decomposition of enargite occurs through the formation of intermediate tenantite, according to the following sequential reactions: 4Cu3AsS4(s) ? Cu12 As4S13(s)+ 3/2S2(g) Cu12 AS4S13(s) ? 6Cu2S(s) + 2As2S3(g) + 1/2S2(g) The decomposition kinetics was analyzed by using the model for a topochemical reaction of spherical particles: 1-(1-X) 1/3 = kt, which represented well the data. Apparent activation energies of 113 kJ/mol and 60.5 kJ/mol were found for the low and high temperature regions, respectively.

Jan 1, 1999

By Guohua Bai, Yuanbo Zhang, Guihong Han, Zijian Su, Daoyuan Zhang

"Specularite ores have poor hydrophilicity and ballability as well as inferior high-temperature reactivity, which restrict the large-scale application of them in the pelletizing and sintering production. Modified humic acid (MHA) organic binders are firstly used for pellet preparation from specularite in this paper. The results show that the drop strength of green pellets is 3.7 times/0.5m and compression strength is 12.5 N/P by using 1.0 wt% MHA as binder. Under the optimal experimental conditions of preheating temperature 980 °C, preheating time 12 min, roasting temperature 1280 °C and roasting time 10 min, the preheated pellets have the compression strength more than 400 N/P, and that of roasted pellets is 2747 N/P. The strength of finished pellets meets the requirements of blast furnace iron-making. MHA is a kind of more effective organic binder for specularite pellets compared with the inorganic bentonite.IntroductionAcid Pellets have advantages of good strength, uniformity particle size, high iron grade and good reducibility, which can be used as high-quality burdens for blast furnaces [1]. With fast development of Chinese iron and steel industry domestic magnetite concentrates with high grade of iron and good firing performances become shortage.Imported specularite ores have advantages of low price and high grade of iron (generally above 67 wt%), so the application of them in pellets is an effective way for sustainable development of pellet industry in China. However, the specularites have not been utilized in pelletizing and sintering at present because of the poor ballability and high-temperature reactivity [2, 3]. Most of the pellet plants use bentonite as binders, the amount of which is about 2~3 wt%. The pellet production practice shows that 90 wt% bentonite is still residual in finished pellets and reduces the iron grade [3]. Developing a new organic binder instead of bentonite is very important to the high-quality pellet production. On one hand, the consumption of bentonite is obviously reduced, resulting in decreasing the ironmaking coke ratio and slag discharge; On the other hand, the iron grade of finished pellets are improved, which brings the benefit for the ironmaking production."

Jan 1, 2011

By Yong J. Kim, J. M. Park

"Solid/melt interface shape during continuous casting process has a strong influence on the resulting microstructure of the ingot. The interface shape is primarily governed by the heat flow condition between the molten metal and mold (or container). The roll of the microstructural transition resulting from various solid/melt interface shapes is discussed using the Sn-22.6wt%Pb alloy. Three different types of mold such as cold mold, resistantly heated mold, and electromagnetically heated mold were used to generate those interfaces having different curvatures. Experimental measurements of complete temperature profile along the axis and surface of the ingot during downward continuous casting are presented to determine the solid/melt interface geometry. The results provide an explanation of the ingot property with emphasis on microstructure.IntroductionA large scale of continuous casting process of alloys often has a rather deep V channel type of solid/melt interface resulting from a limited heat flow condition. As a result, the deep V type solid/melt interface shape entraps defects such as pores and inclusions and also creates canter segregation. In order to reduce the defects concentration, electromagnetic stirring(EMS) mechanism has been applied to the melt in the channel[l]. Speith and Bungeroth introduced first experimental EMS device to the continuous caster in 1952.[2] Today, with wide ranges of benefit, a large variety of such technique is available. Electromagnetic field on the melt can be divided into three aspects. First, eddy current is induced on the metal surface by alternating magnetic field with high frequency, which results in heating the metal. Second, electromagnetic body force which is generated by the magnetic field and the eddy current reduces the melt pressure on mold or support the melt not to contact with the mold[3,4,5]. This force is used for electromagnetic casting process(EMC). Finally, it causes stirring in the melt. Many research efforts have been done on the EMC process to improve surface quality of slab[6] and control meniscus shape where three phases such as melt, solidified metal, and mold powder coexist[7,8]. However, the eddy current heating effect on the surface of the ingot was less considered. It is worth noting that induced eddy current on the surface of slab melts the solidified shell and thus changes the heat flow condition between the mold and melt. Mold heating effect was first proposed by A. Ohno[9] and its processing conditions were identified in details[ 10, 11]. The so-called Ohno process is based on the fact that by keeping the mold temperature slightly above the melting temperature of the liquid, no grain can be nucleated on the mold wall[12]."

Jan 1, 1998

By Fumito Tanaka

The Mitsubishi process is the sole pyrometallurgical process for the continuous production of blister copper from Copper concentrates and has been successfully operated around the world. The development of calcium ferrite slag (CaO-FeOx-Cu10), the so-called "C-slag", has enabled continuous converting from matte to blister copper in the commercial scale operations. Commercial interests in the slag led to many papers over the CaO-FeOx slag. However, Cu2O bearing slag has not been studied well due to experimental difficulties. The authors have quantified the thermodynamic properties of the CaO-FeOX-Cu2O system. The results have been utilized to analyze various issues related to the converting furnace, such as the magnetite precipitation from the slag or from blister copper and to develop better controlling criteria for the continuous converting operation. -

Jan 1, 2003

By Fumito Tanaka

The Mitsubishi process is the sole pyrometallurgical process for the continuous production of blister copper from copper concentrates and has been successfully operated around the world. The development of calcium ferrite slag (CaO-FeOx-Cu20), the so-called "C-slag", has enabled continuous converting from matte to blister copper in the commercial scale operations. Commercial interests in the slag led to many papers over the CaO-FeOx slag. However, CU2O- bearing slag has not been studied well due to experimental difficulties. The authors have quantified the thermodynamic properties ofthe CaO-FeOx-Cu2O system. The results have been utilized to analyze various issues related to the converting furnace, such as the magnetite precipitation from the slag or from blister copper and to develop better controlling criteria for the continuous converting operation.

Jan 1, 2003

By Laurent Cohen

Since the 1970s, Solvent Extraction (SX) in hydrometallurgical processes has been a key enabling technology in the production of high-purity metals. Examples include copper, rare earth oxides, uranium, cobalt and nickel. Notwithstanding incremental improvements in extractant formulations, few breakthroughs can be recounted in this industry outside of the initial amine-, oxime- or phosphine-based reagent chemistries. However, the advent of lithium-ion batteries and their stringent requirements for critical materials (lithium, cobalt and nickel) offer new challenges and opportunities for SX. Solvay recently introduced a new extractant for lithium, CYANEX® 936, and developed unique modeling software capabilities in cobalt/nickel separation using CYANEX® 272, zinc SX using DEHPA® and rare earth separations using CYANEX® 572. This paper discusses trends in SX and provides insight on processing of critical materials essential to energy sources. It also summarizes the technical and economic benefits based on extractant selection and advances in modeling.

By I. Mc Dougall

"The matte/slag tidal zone in a platinum smelting furnace is subject to severe process conditions which can often lead to premature failure of the lining. The MgO-FeO-Si02 slag is aggressive to refractory bricks, whilst the Ni-Cu-Fe-S matte is aggressive to water-cooled copper cooling elements, and can penetrate and sulphidize refractory bricks, particularly at the high matte temperatures often experienced in the PGM industry. A novel approach to the lining design was taken at Lonmin's new 10MW Furnace 2. An indirectly-cooled graphite ring was applied in the matte/slag tidal zone, with refractory bricks on the hot face. Thermal Finite Element modeling was conducted to determine the optimal lining design in this region of the furnace. The resistance of two graphite grades to damage by slag and matte was evaluated experimentally. The graphite lining is not wet by the matte, and is resistant to slag attack at operating temperatures. In comparison to water-cooled copper in various configurations, cooled graphite shows promise as an indirect refractory cooling system in the tidal zone area of furnaces.IntroductionIn South African Platinum Group Metals (PGM) smelting operations, the PGMs are associated with nickel-copper sulphides in magmatic rocks. After ore is mined, it is concentrated by means of a flotation process prior to smelting. Both rectangular 6-in-line and circular 3 electrode AC submerged arc furnaces are used for this purpose. A new 10 MW round furnace is currently under construction by Tenova Pyromet at Lonmin's Marikana Smelter Division. An overview of Lonmin's smelting operations and Lonmin's approach to smelting high chromite containing PGM concentrates is given by Eksteen et al. [1]"

Jan 1, 2012

By J. E. Dutrizac

Fracture-exposed surfaces of sphalerite samples having five different solid solution iron contents ranging from 0.0 wt% to 14.8 wt% Fe were leached for 15 to 120 s at 100°C in 0.3 M Fe(S04)1.5 -0.3 M H2S04 media. The reacted samples were examined using X-ray photoelectron spectroscopy (XPS) which provides chemical state information on the first few nanometers of the solid surface. Surface compositions show that the leaching rate increases with increasing solid solution iron content of the sphalerite. Detailed evaluation of high resolution S2p spectra show that the leaching progresses via the formation of polysulphide species. Disulphide species were not detected in any of the experiments. Examination of the Zn2p and Fe2p spectra indicate little change in the chemical states of these elements over the duration of the experiments. Longer leaching times resulted in the generation of elemental sulphur. The ratios of elemental sulphur to dissolved ferrous ions and zinc suggest that less than 5% of the sulphide is oxidized to sulphate. Morphological studies showed that the elemental sulphur commonly formed at a few isolated sites, such as the grain boundaries. Furthermore, euhedral sulphur crystals were often identified. These observations suggest that at least part of the elemental sulphur forms via dissolved sulphide species which are oxidized in solution by ferric sulphate.

Jan 1, 2003

By Hang Goo Kim

A computer simulation has been carried out to predict the distribution behavior of minor elements such as Pb. Zn, Bi, Sb and As in recently proposed copper smelting and converting processes with submerged oxygen injection in which tonnage oxygen is used with a shielding gas. In this study the technique of stepwise equilibrium modeling was employed and some of the thermodynamic data were updated or reassessed. The volatilization and slagging of undesirable elements were investigated in copper smelting (steady-state) system, copper matte converting (batch) system, and the combined (smelting + converting) system at extremly high oxygen-enrichment levels. The predicted minor-element behavior under high oxygen- enrichment was compared with that in the Noranda process (normally 42% oxygen-enrichment in smelting and 24% in converting) and the reverberatory process using air. The effects of various operating parameters such as temperature, the final matte grade in smelting, the initial matte grade in converting and the O/Fe ratio in slag on the behavior of minor elements are discussed.

Jan 1, 1991