Search Documents

By Jafar Safarian

Bauxite is the main raw material used for the production of alumina (Al2O3) through the well-known commercial Bayer process. This process has significant challenges such as limitation in using low-grade bauxites as they contain significant amounts of impurities such as Fe, Si, Ti. The Bayer process residue, which is known as red mud, is also a global environmental challenge due to huge amount of this low value residue production. An alternative sustainable process with high potential to solve these problems and produce valuable and consumable by-products is a pyrometallurgical-hydrometallurgical process in which the low-grade bauxite ore is treated through a smelting-reduction process, yielding iron alloys and a calcium-aluminate slag. Alumina is then produced from the slag by hydrometallurgical treatment. In the present work, the reduction of pellets produced from different bauxite ores by hydrogen is studied and it is shown that complete iron oxides reduction is possible. Further smelting and smelting-aluminothermic reduction of the reduced pellets show that iron and silicon ferroalloys can be produced, in addition to a proper slag for alumina extraction.

By Messias dos Santos Machado, Renato B. Godoy, Roberta Lima, Andressa Silva, Francisco Valenzuela-Díaz, Rene R. Oliveira, Esperidiana Moura

This work aims to incorporate the Bof White Clay, from Boa Vista, Paraiba State, Brazil, as natural nanofiller in Ehylene vinyl alcohol copolymer (EVOH) and obtain flexible films. Nanocomposite was obtained using a twin-screw extruder, and film formed using a blow extruder machine. The flexible film nanocomposite was characterized, by tensile tests, XRD, DSC and their properties were evaluated. The results showed a good interaction between the clay and the EVOH resulting in an increase of properties of films nanocomposites as compared to films neat polymer.

Jan 1, 2015

By W. Song, C. Richards, B. Q. Li

"This paper presents a two-phase flow numerical model for spouting gas-particle flow reactors used in chemical vapor deposition processes for manufacturing heart valves and other biomedical implants. The model is developed based on the Eulerian-Eulerian formulation of gas-particle flows, with the k-e engineering model modified with the presence of particles for the description of turbulent gas flows. In parallel with the numerical model development, physical models are set up, where the particle image velocimetry is used for visualizing the particle flows and spout shapes and heights and optical probes are used to measure the particle velocities. The numerical model predictions are compared reasonably well with the experimental measurements.IntroductionVarious biomedical implant components, such as bone joints, dental components and heart valves, are coated with bio-compatible thin films by chemical vapor deposition in particle-laden chemical reactors [l-5]. In these reactors fine particles are used as packing and supporting media. During the coating operation, these packed particles are fluidized by an upward gas jet from the nozzle, reach a certain height and fall back on the top of an annulus region. These recirculating particles are mainly for levitating the implant components (usually one or two in a reactor at one time) so that every portion of them is equally exposed to the gaseous atmosphere. An equal exposure is critical for forming a uniform, mechanically strong and corrosion-resistant coating on implants. Plant experience shows that the quality of the coating is directly related to a stream of operating parameters such as temperature, particle size and loading, and gas flow rates [6]. Optimization of these operating parameters for improved reactor performance depends crucially upon our fundamental understanding of the physics governing the gas-particle flow, heat, and mass transfer phenomena taking place in these reactors."

Jan 1, 2004

By Christoph Sagadin

Corrosion mechanisms between high melting synthetic ferronickel slags and refractory were investigated. The used slags were prepared by mixing and melting of specific oxides. Substrates of the applied refractory material and specimens of FeNi slags were heated in a hot stage microscope up to 1650 °C. The experiments were performed under a defined gas atmosphere of 60% CO and 40% CO2. A further examination of the formed phases between slag and refractory occurred by scanning electron microscope. The investigations indicate that the slag penetrates between magnesia grains and partly dissolves magnesia. Spot analyses show that iron diffuses into the magnesia grains, which transform to magnesiawustite, meanwhile SiO2 forms different types of olivine like forsterite and monticellite. Thermodynamic calculations confirm the formation of these phases. The combination of practical lab scale experiments and thermodynamic calculations should finally contribute to an improvement of the refractory lifetime and performance.

By Mingming Zhang

"Three samples received from the EAF shop have been characterized by chemical, X-ray diffraction (XRD), optical microscopy (OM) and scanning electron microscopy (SEM) methods. The objective of this characterization work is to investigate the occurrence of nickel, copper, zinc, sulfur and phosphorus in these samples and identity their origin and associations with iron minerals in the concentrate samples that are from mines.The samples were identified as Mineral, Pellet, and HRD. The latter is the DR! product. All three samples were received as fine powders. The results indicate that, in the mineral sample, magnetite is the major iron oxide mineral with hematite as a second phase based on the OM and XRD studies. Pyrite [FeS2], chalcopyrite [CuFeS2] and bravoite [(Fe,Ni)S2] are major sulfide minerals. Trace amounts of apatite [Ca5(P04)3(F,Cl,OH)], wardite [Na4CaA112(P04)8(OH)8 6H20], giniite [Fe5(P04)4(OH)3 2H20] and vivianite [Fe3(p04)2 8H20] were identified by SEM and XRD. Microscopic studies also indicated that most of the sulfide grains in the mineral sample are present either as liberated fine particles (about 10 microns) or as inclusions within the magnetite and hematite grains. XRD studies revealed magnetite as the major mineral with subordinate amounts of hematite and pyrite confirming the microscopic findings. Copper, nickel, and zinc are mainly present as chalcopyrite, bravoite, and franklinite [(Zn,Mn,Fe)(Fe,Mn)204] in trace amount in the mineral samples, respectively. Impurities carry over to the Pellet and HRD samples.Chemical analyses of the three iron-bearing samples indicate that sulfur and phosphorus in the Pellet sample exceeded the specification. Since liberated pyrite and chalcopyrite particles were observed both in mineral and pellet samples, magnetic and flotation processing routes for this ore should be effective for sulfide removal but at the cost of iron losses. The high phosphorus content of all three samples indicates that there are phosphates which are difficult to remove by the current concentrating process (magnetic separation and flotation)"

Jan 1, 2012

By Yong Li, Tao Jiang, Xiangxin Xue, He Yang

"In this paper, we describe the current status and research progress on the utilization of typical industrial solid wastes in China. We propose a creative method called “eco-utilizing wastes” with an aim of both integration and increment but without second-time waste and pollution, in terms of the characteristics of typical industrial solid wastes, such as titanium-bearing blast furnace slag, high-silicon iron tailing and boron-enriched slag as well as oil shale.Situation of Typical Industrial Solid Wastes in ChinaThough mineral resources in China are abundant, most of these are low grade ores. Moreover, the distribution of mineral resources is asymmetric, which causes the increase of cost and decrease of the economic benefit. Over-exploitation of mineral resources results in a large number of solid wastes. The accumulation of solid wastes not only means the waste of valuable resources, but also causes environment deterioration. There exist some problems in the current practice of the disposal of industrial solid waste, such as only emphasizing the final results and causing new pollution and waste [1]. So the research and development of a high value-added method has a high practical relevance to our nation. Based on the present status and research progress of industrial solid wastes in China, a creative new idea and method for eco-utilization of solid wastes is proposed in this paper."

Jan 1, 2012

By Carlos Eduardo Gomes de Souza, Luis G. S. Sobral, Paulo A. Medeiros da Silva, Selma G. F. Leite, Renata de B. Lima

"The use of mixed cultures of acidophilus microorganisms that act in different temperature ranges, aims at speeding up the digestion of chalcopyrite, highly refractory sulphide mineral, the major mineral in the flotation concentrate of Caraíba Mining Co., with an attractive processing cost. The concentrate under consideration contains mainly chalcopyrite (CuFeS2) and bornite (Cu5FeS4) with contents of, approximately, 70 and 30%, respectively. It was observed in this study, the performance of consortium of mesophiles, moderate and extreme thermophile microorganisms, in the oxidation of the aforementioned sulphides minerals, evaluating operational parameters such as pH of the leaching solution, the reaction temperature and redox potential, with consequent extraction of 80% of the concentrate copper content within 60 days of bioleaching. Such high copper extraction was achieved in column bioleaching tests.INTRODUCTIONThe solubilization of metals by the application of microorganisms from the mineral ores and the subsequent recovery of metals from solution are referred to as bioleaching (Rohwerder, T et al, 2003). This is an economical method for the recovery of metals from minerals; especially lowgrade ores, overburden, and waste from current mining operations which requires moderate capital investment with operating cost (Watling, 2006).Furthermore, bioleaching is generally more environmentally friendly than conventional metal recovery processes such as concentration and smelting. Those physicochemical metal extraction processes generate sulphur dioxide, a toxic emission that is increasingly the target of regulatory legislation (Stott et al., 2000; Olson et al., 2003). Bioleaching of chalcopyrite is the key industry target. The main problem hindering commercial application of chalcopyrite bioleaching is the slow dissolution rate (Fu et al, 2008).Dissolution of acid-soluble sulphide minerals such as sphalerite, and to a lesser extent chalcopyrite, occurs by a combination of ferric iron and proton attack via the polysulphide pathway (Rohwerder et al., 2003)."

Jan 1, 2008

By Manoj Kumar, Vinay Kumar, Nikhil Dhawan, Manish Wadhwa

"Electronic waste (e-waste) is a collective name given to discarded electronic devices such as Television, Cellular Phones and Personal Computers. Among the heterogeneous metals present in the e-waste are the base metals: copper, aluminium, nickel, tin, zinc, iron and precious metals: gold, silver, palladium, platinum apart from several hazardous and halogens metals. Hence there is a need to recover these metals from electronic scrap by recycling and then re-use, which can meet large amount of metals demand. Hydrometallurgical processing was employed for the recovery of metals from television printed circuit board (TV PCB). Different lixiviants such as hydrochloric acid, Sulphuric acid, and nitric acid were used to understand the dissolution behavior of copper, iron and lead present in the TV PCB. Effect of increasing concentration of nitric acid was also studied. Selective recovery of tin over 95% in the form of tin oxide was precipitated. The precipitated tin oxide was identified by X-ray diffraction technique. Tin oxide of purity more than 99.9% was obtained.IntroductionThe electrical and electronic industries comprising computers, television, mobiles, etc, which are manufactured utilizing printed circuit, boards, capacitors, resistance, soldering material etc. During production, at the end-of service life and degradation due to the advanced version with latest features generate valuable metallic and non-metallic constituents. European Union Council on waste electrical and electronic equipment (WEEE) has classified these into different categories as listed in Table 1 [Streicher-Porte et al., 2005]. Among these the information technology, telecommunications and consumer equipment constitute electronic waste (e-waste) [EC, 2002]. Almost all e-waste consists of an integrated part of printed circuit boards which is a valuable source of several metals such as copper, tin, lead, aluminium, iron, silver, gold, platinum etc. [Relay et al., 1990]."

Jan 1, 2008

By Xiang Ma, Halvor Dalaker, Kai Tang, Stefan Andersson

Silicon carbide (SiC) is one of the most important non-oxide ceramic materials for many industrial applications and is mainly synthesized by carbothermic reduction of silicon oxide by coke above 2200°C. Replacing natural gas (mostly methane, CH4) for coke in SiC synthesis could considerably reduce energy consumption and CO2-emissions owing to higher carbon activity of CH4 at lower temperature. The generally accepted reaction mechanism is that SiC is synthesized through gaseous intermediate silicon monoxide, SiO. In the present study, the reaction mechanism for the SiO and CH4 gaseous mixture has been examined using atomic scale modelling. Molecular dynamics (MD) using a reactive force field (ReaxFF) has been utilized to examine the initial stages of reactions involving a gas mixture of SiO and CH4 and surfaces of SiC. The MD results revealed some interesting SiC formation mechanisms. The reaction energies of the critical intermediate species were also estimated by density functional theory (DFT) calculations and the implications for the force field parameters used in ReaxFF was discussed.

Jan 1, 2015

By Jian Li, S. Penttila, W. Zheng

"Materials selection for Gen IV supercritical water reactor in-core components faces major challenges due to severe operating condition. Beside high-temperature mechanical properties, SCC and general corrosion resistance of commercially available materials are also major focuses in recent research. Recent reports suggest that certain types of surface modifications are beneficial to SCW corrosion resistance. In this study, the effects of surface modifications are investigated, and possible mechanisms for improved corrosion performance are discussed.IntroductionThe current Canadian pressure-tube supercritical water reactor (SCW) design specifies a core outlet temperature of 625°C under 25 MPa of pressure, with peak cladding temperature as high as 850°C. Challenges in materials selection include high-temperature mechanical properties, corrosion resistance, SCC resistance and radiation damage. Most of the SCW corrosion test results available are below 730°C. Early work by Allen [1] summarized the corrosion resistance of alloy groups including Ni-based super alloys, stainless and ferritic/matensitic (F/M) steels that can potentially be used for SCW reactors. F/M steels can only be used at low temperature sites (e.g. down stream piping). At 500°C and 25 MPa, F/M steels develop a thick but mechanically stable oxide layer. However, the long term stability of the surface oxide layer is largely unknown. Ni-based alloys appear to form very thin surface oxide, however pitting was observed in the vicinity of some intermetallic precipitates [2-5], and dissolution of major alloying components could pose significant problems for down stream piping [6]. In addition, concerns of Helium formation due to Ni transmutation prevented this alloy group to be used as fuel cladding. The corrosion resistant austenitic stainless steels (e.g. 316L) are found to be susceptible to localized corrosion such as pitting, intergranular attack and stress corrosion cracking (SCC) [7]."

Jan 1, 2012

By Roger Altman

The solubility of copper in primary spinel crystals encountered in reverberatory slag samples has been determined by electron microprobe analysis. These spinels, which ranged in composition from 22% A12O3 to pure magnetite, contained small quantities of dissolved copper (0-0.4%). Based on literature data it was estimated that the solubility limit of copper in solid magnetite is no greater than about 1% at 1200°C and about 2% at 1250°C. However, it was found that practically every spinel crystal examined contained significant amounts of matte inclusions. Further examination of converter slag revealed large quantities of irregularly shaped precipitated magnetite crystals which contained a large proportion of copper inclusions. Additional experimentation showed that the total copper content in reverberatory slag samples was greater than the sum of the estimated en- trained plus dissolved matte in the slag. This difference is believed to be significant and is due to the presence of matte inclusions in the spinel crystals. In the present reverberatory slag samples these inclusions accounted for about 1/2 of the amount of sulfide directly entrained in the slag.

Jan 1, 1976

By Emmanuel N. Zevgolis

In the present work, a reduction roasting experimental study of Greek nickeliferous laterite samples with a gaseous reducing mixture ? CO:N2- is presented. The effect of parameters such as temperature, ore grain size, and composition of the reducing mixture were examined. It is deduced that the reducibility of intermediate type laterite sample, where iron appears mainly in the form of goethite (a-FeOOH), is considerably higher than that of limonitic type laterite samples, where hematite (a-Fe2O3) is the predominant iron mineral phase. The degree of reduction of the limonitic type laterite samples does not exceed 50%, while it reaches 95% in the case of the intermediate-type laterite sample under the same experimental conditions. Increasing the temperature in the range 750-900°C does not considerably favor the reduction of the limonitic type laterites, whereas decrease of ore grain size of the limonitic-type ore samples and more intense reducing conditions increase the reduction. The considerably higher specific surface area values of the intermediate laterite samples, diminishes the effect of the ore grain size and this can be regarded as the critical parameter leading to the higher reducibility of this ore.

Jan 1, 2009

By Kymberley Worrell

The Cripple Creek and Victor Gold Mine was acquired by Newmont in August 2015. The high grade flotation mill project was commissioned in February 2014. The mill to date has been throughput limited due to mechanical and design issues. In order to create the most value from a throughput limited plant a campaign to provide timely ore characterization was undertaken. A diagnostic leach methodology was developed to determine gold associations by ore type. The resulting associations were then used to characterize feed blend; gold losses and optimize gold production. The diagnostic methodology is presented along with discussion on flotation implications.

By Ana E. Bohé

Chlorination process is an attractive and efficient method for the metal recovery from complex materials. The process that is performed at high temperatures, allows converting all the metals contained in the material into their respective chlorides which are further separated in a selective way. Aluminum metal matrix composites with discontinuous ceramic reinforcement of short fibers, whiskers, and particles have been gaining wide acceptance as an important engineering material in automotive, aerospace, and electronic industries. Since the ceramic reinforcements are still quite expensive and contribute significantly to the final cost of composite materials, the feasibility of their recovery from the manufacturing scrap and further recycling is a factor of increasing economic interest. In the present work, a theoretical and experimental study is given for the recovery of Al2O3 and SiC particles and short fibers from three commercially available aluminum-matrix composites produced by molten metal mixing route. The process consists of transforming the constituents of metallic alloy matrices in gaseous chlorides that are dragged by the gaseous stream, while the ceramic reinforcement remains as a solid residue in the reaction bed.

Jan 1, 2006

By Mei Song, Qingyu Deng, Xuewei Lv, Lu Liu, Chenguang Bai, Meilong Hu

"The carbochlorination of several silica materials was carried out in the temperature range from 900 °C to 1200 °C. In this study, silica oxides and gaseous chlorine with carbon as reductant were used. The optimal carbon silica mole ratio in different temperature was calculated by Factsage software and the results showed that the optimal values are 1.2, 1.4, 1.6, 1.8 at 900 °C, 1000 °C, 1100 °C, 1200 °C, respectively. According to the experiments, the chlorination ratios of several silica materials were increased with temperature increasing. In the same temperature, the chlorination ratio of diatomite is the maximum and the chlorination ratio reaches 79%% when C/SiO2 reaches 3 at 1100 °C.1, IntroductionPolycrystalline silicon is the main material to manufacture the silicon polished section, solar battery[1] and high purity silicon wafers[2], also which is the most basic function material of semi-conductor industry, electronic information industry and solar photovoltaic battery industry[3]. The conventional manufacturing process of polycrystalline silicon would be divided into three parts: the improved Siemens method, which was introduced and became the main process to produce the polysilicon products in China. Silane method and fluidized bed method. Silicon tetrachloride and chlorosilans have been employed as by-products in several fields like electronic, telecounications and metallurgy[4-6]• At present, the main applications of silicon tetrachloride include production of trichlorosilane by catalytic hydrogenation, synthesis of fumed silica and ethyl orthosilicate, production of optical fiber grade silicon tetrachloride.The conventional routes for the silicon tetrachloride production have been reported, including the direct chlorination and the chlorination process of ferrosilicon, abandon catalyst and silica[7]."

Jan 1, 2013

By Metehan Erdogan, Mustafa Serdal Aras, Sedef Cift Karagul, Ishak Karakaya, Esra Karakaya, Merve Kolay Ersoy

Pickling is the treatment of metal surfaces by removing oxide layer, rust, scale, inorganic contaminants or other impurities from ferrous metals, copper or precious metals. A strong inorganic acid such as hydrochloric acid is used for plain carbon or low alloy steel pickling. When the concentration of copper in the pickling solution exceeds about 100 mg/L, reversion may take place and randomly plating of copper onto the steel strips which causes visual incompatibility occur. Furthermore, efficiency of pickling decreases with the increase of copper content. The reversion may be delayed to higher Cu concentrations by adding fresh acid to the line. Increased acid consumption only delays the time to discard the solution but increases the cost and hazardous nature effect on the environment. An experimental electrochemical procedure has been conducted to remove copper from pickling solution to reduce the concentration below 100 mg/L. Within this scope, effects of applied current density, copper concentration and electrolysis duration on copper deposition were studied. Current density was determined as the most effective parameter to remove copper from the regenerated pickling solutions of steel plants.

Mar 1, 2018

By Kristine Bruce Wanderley, Denise Crocce Romano Espinosa, Jorge A. Soares Tenório

Mining of nickel ores generates large volumes of waste that must be removed in order to eliminate water contamination and reduce environmental impacts created by waste barriers. In this context, the need for innovations concerning the recovery of magnesium present in the liquor produced by the leaching of nickel laterite with sulfuric acid arises. Therefore, this work aims to develop a study regarding the crystallization of magnesium from a synthetic liquor solution using a batch autoclave system at high temperature. Agitation speed was kept constant at 1000 rpm throughout the 3 h of batch reaction for temperatures of 230 and 200 °C. Aliquots taken at each hour were analyzed by ion chromatography to measure magnesium concentration. The highest magnesium removal was observed for temperature 230 °C. X-ray diffraction (XRD) and scanning electron microscopy (EDS-SEM) analysis proved that the product formed was magnesium sulphate monohydrate crystals. Thermogravimetric analysis coupled with a mass spectrometer was used for the evaluation of the thermal stability of magnesium sulphate monohydrate. It was found that MgO and SO2 were formed by the decomposition of the salt at 1100 °C.

Mar 1, 2017

By Massoud Hassanabadi

Filtration using Ceramic Foam Filters (CFFs) is a method widely used to separate inclusions from molten aluminium. In the present work, the specific permeability and form drag coefficients of nominal 50 mm thick commercial Al2O3- based CFFs, of grades 30, 50, 65 and 80, have been calculated from pressure drop experiments using high (60–500 mm s−1) and low (0.2–10 mm s−1) water velocities. Moreover, 2D axial symmetric Computational Fluid Dynamic (CFD) models have been developed, using COMSOL Multiphysics® to validate the experimental results. The empirically obtained values were defined as global parameters used to model the pressure, as well as the velocity fields in the water pipes and in the CFFs. The modelled pressure drop over the filter thickness for the high water velocity experiments showed < ± 1% deviation from the corresponding experimental results for all CFF grades. Moreover, the developed model also showed good agreement with the experimental results obtained from the low water velocity experiments, where the deviation of the pressure drop for the CFF samples of grade 30, 50 and 65 were ≤ ± 4.6% and for CFF samples of grade 80 ≤ ± 13.4%.

By Thais Cristina da Costa Caldas, Alline Sardinha Cordeiro Morais, Carlos Maurício Fontes Vieira, Sergio Neves Monteiro

"This work has as its objective to evaluate the firing behavior of a kaolinitic clayey body from Campos dos Goytacazes-RJ incorporated with flat glass waste (FGW) from civil construction. Incorporations of the waste, with a particle size less than 74 µm (200 mesh), were performed in the red ceramic in the following amounts: 0, 2.5, 5 and 10 wt%. Specimens were prepared by uniaxial press-molding and then fired at 850 and 1050°C. The characterization of FGW was done by X-ray Fluorescence. The physical and mechanical properties evaluated were: linear shrinkage, water absorption and flexural rupture strength. The microstructure of the fired ceramics was evaluated by optical microscopy (OM). The obtained results showed that the flat glass waste can be used as a component of ceramic bodies once it was noticed tolerable modifications of technological behavior.IntroductionBrazil is one of the world’s largest producers and consumers of clayey ceramic. Campos dos Goytacazes is located in the north of the State of Rio de Janeiro, southeast of Brazil, it’s known as a large producer of red ceramics. It is estimated that the production of bricks can reach 1 billion pieces per year [1].Nowadays, recycling processes became more and more important, due the generation of wastes in large scale and the preoccupation with environmental. The amount of glass waste has been exponentially growing with the growth of the population. It is estimated that the amount of discarded glass as bottles, construction windows, packing and other glass waste represented in 2006 an amount of 7.5% of the total weight of the world´s domestic garbage [2]."

Jan 1, 2012

By E. James Quinn

Solvent extraction technology using EHEHPA (2-ethylhexyl phosphonic acid, 2-ethyhexyl mono ester) is the norm for industrial separations of rare earth elements. This process has some shortcomings, including a large number of stages compared to most SX processes and high acid requirement for stripping of the heavy rare earths. In this work, we examine a number of alternative mixed solvent extraction systems: (i) Mixtures of organophosphonic and phosphinic acids such as EHEHPA/Cyanex 272 or Cyanex 572; (ii) Ionic liquid mixtures of EHEHPA with quaternary ammonium chloride (Aliquat 336); and (iii) Mixtures of carboxylic acids for yttrium/lanthanide separations. We discuss and compare the efficacy of these systems with reference to the Nd/Sm separation, which is of industrial significance. Based on the extraction chemistry and the use of modelling tools to define the counter-current solvent extraction circuit, we present a techno-economic analysis of a separation plant and discuss the impact of various solvent systems on the capital expenditure (CAPEX) and operating costs (OPEX).