Search Documents

By Jianhang Hu, Li Yang, Yonggang Wei, Kongzhai Li

"In this paper, the pyrolysis of biomasses including bamboo, sawdust and walnut shell were performed in a tube furnace under temperatures between 400? and 600? to obtain biomass carbon, gas, and tar. Textural parameters analysis revealed the caloric value of biomass carbons between 32 MJ/kg and 34 MJ/kg. It also indicated that the surface of biomass carbon consists of mesopore and macropore structures. By using GC analysis, it was determined the main ingredients of pyrolysis gas are CO, H2, CO2, CH4, C2H4 and C2H6. Calculation states that the density of pyrolysis gas is roughly between 1.0 kg/m3 and 1.7 kg/m3, while the calorific value of pyrolysis gas is between 12000 kJ/m3 and 16500 kJ/m3, illustrating that pyrolysis gas is a median gas. The calorific value of biomass tar was found to be between 32 MJ/kg and 34 MJ/kg, with more than 80 compounds in the biomass tar identified by GC-MS method.IntroductionBiomass as a renewable source is the world's largest and most sustainable energy resource [1].The conversion of biomass has the potential to be a renewable and carbon neutral method of producing fuels and chemicals [2-4]. Pyrolysis is a thermo-chemical process defined as applying heat to degrade biomass in an inert atmosphere. It transforms unstable biomass and other organic materials into biomass carbon, gas, and tar [5]. Biomass carbon can be stored or transported much easier as compared to parent biomass or be converted to value added products such as activated carbons[6]; gas is a relatively low-energy-density fuel; tar can be considered as a source of useful chemicals[7].The characterization of biomass pyrolysis will lead to its increased understanding and utilization as a source of solid, liquid and gaseous products which can be used as fuels and petrochemical feedstock[8,9].In recent years, many researchers studied the effect of temperature on biomass pyrolysis product distribution characteristics in a variety of pyrolysis reactor[10]. Ramin Azargohar's paper [11] presents the results of characterization for biomass and investigates the effects of pyrolysis temperature on the pyrolysis products obtained by fast pyrolysis of four different types of biomass."

Jan 1, 2014

By cheng Peng-fei, TANG Hai-yan, guo Xiao-chen, LI Jing-she, Liang Yong-cang, Zhao Baojun

In the process of oxygen blast furnace, the lower coke ratio and the higher coke load make the skeleton coke more important. To understand the dissolution of coke in melting and dropping zone, the influence of FeO content, temperature and reaction time on the dissolution of coke with slag were studied by single-factor experiment. Meanwhile, the three factors and three levels orthogonal were conducted. The dissolution degrees were characterized by the weight loss ratio and diameter variation. The results showed that the weight loss ratio increased and the diameter decreased with the increase of FeO content, temperature and time. The three factors and three levels orthogonal test showed that time was the most significant factor on coke dissolution, FeO content of the second, and finally the temperature. The microstructure of coke after reaction indicated that the dissolution occurred on coke surface.

Jan 1, 2016

By C. J. Newman

Prior to 1995, the smelting process at the Kennecott Utah Copper Corporation (KUCC) smelter consisted of Noranda reactors and Pierce-Smith converters. In the consideration of expansion opportunities, the existing process did not lend itself to a program geared towards processing the total output of KUCC mining and milling operations. During 1989 and 1990, a number of smelting options were evaluated. The final selection was the Outokumpu flash smelting process, coupled with the new Kennecott-Outokumpu flash converting technology. Facilities were designed and installed to process 1:0 million tonnes per year of copper concentrate, with the ability to expand to 1.2 million tonnes per year. Following the shutdown of the smelter facility utilizing the Noranda technology in May 1995, the flash smelting, furnace commenced operation in June with the flash converting furnace startup following a few weeks later. The smelter has achieved design production targets and environmental goals. Current operating rates are at or above design rates for concentrate and matte processing. Emissions are lower than the permit levels and equate to less than 3.5 kg of SO2 per tonne of copper. This paper outlines the design, construction, startup and the first two years of operation of the modernized KUCC smelter.

Jan 1, 1998

By Corby G. Anderson

Hydrometallurgical technology for the pretreatment of refractory gold concentrates has been developed at Sunshine Mining and Refining Company. It employs a patented nitrous-sulfuric acid pressure leaching process which' was proven industrially at the Sunshine refinery. Additionally, pretreatment for removal of antimony and some other impurities is done with alkaline sulfide leaching. This paper will discuss the successful application of these two technologies for pretreatment of a refractory gold concentrate prior to CIL gold recovery. A complex gold concentrate composed of pyrite, arsenopyrite and stibnite was tested. Results of antimony leaching in alkaline sulfide media will be discussed including some details of a novel and selective recovery method for gold leached by polysulfide or thiosulfate" Also, the factors important in and the results of the application of nitrogen species catalyzed pressure leaching to refractory gold concentrates will be detailed.

Jan 1, 1996

By J. Ipinza

The slime formation with several metallic impurities from acidic electrolytes of copper has been studied. On fresh Pb-Ca-Sn anode surface firstly the formation of PbSO4 takes place, then, it is transformed in the conducting PbO2, which covers the anode surface. It has been experimentally established the formation of a manganese dioxide double layer at the anode; this double layer was always composed of a thick external layer of non-adhering and easily removable scales, and of a thin internal layer, which adheres relatively well to the surface of the electrode. It was found that manganese dioxides present in the slime were of different nature: a non-adhering layer produced by electrolysis (-MnO2) on the PbO2 surface and a pure chemical precipitation in the solution (-MnO2). When iron is present in the electrolyte on this last layer of manganese, lead sulfate was found. In the case of arsenic and antimony in the electrolyte the slime generated was found to be lead sulfate and amorphous compounds of those ions. The lower slime generation in Chilean EW plants could be due to the lower contents of iron and manganese in the electrolytes. It was found that this slime formation rate not only is due to the electrolyte composition but also to the poor control of operational parameters at EW plants.

Jan 1, 2003

By William Petruk

A fully automatic image analysis system that consists of a microprobe, an energy dispersive x-ray analyzer, and an image analyzer was developed at CANME:I' to determine mineral behaviour that affects beneficiation. The interlacing between the instruments permits automatic identification and characterization of minerals in samples of unbroken ore pieces and of mill products. Different types of information are obtained for minerals in samples of unbroken ore pieces than in samples of mill products, and are used differently. For unbroken ore pieces size distributions are determined for discrete mineral grains to predict a grind at which they might be liberated, and other measurements are Irade to predict the percentage of mineral that occurs as nonrecoverable grains. For mill products the minerals are analysed to determine percentages that (1) are free, (2) are likely to be recovered in concentrates, (3) are likely to be lost to tailings, and (4) could be liberated with regrinding. The image analysis data for mill products are processed by a mineral-metals balance program to determine the distributions of free and unliberated mineral grains at each point in a concentrator, pilot plant or bench test. For samples containing trace minerals, such as gold, an automatic search technique is used to scan the entire area of the polished section for the trace mineral grains. The identified trace mineral grains are characterized with regard to size, liberation, and other properties.

Jan 1, 1988

By T. R. A. Davey

Previous publications on the application of EIETSIM include the modelling of an electrolytic zinc plant and a copper flash smelter. In the present case METSIM has been used to model the desilverising of lead by the reagent zinc, whereby a silver-zinc intermetallic compound is formed, and floats out of the lead. This compound has a variable composition, depending upon the ratio of dissolved zinc/silver in the lead bath. Its solubility in lead decreases with falling temperature. A number of variations and modifications of the Davey Desilverising Procedure are modelled, and applied to a wide range of silver contents in lead bullions at several plants. METSIM uses both feed- back and feed-forward controls to simulate plant conditions, and a logic control to distinguish between different phases in the Zn-Ag system. Use is made of extensive (previously unpublished) fundamental data on the ternary Pb-Ag-Zn system, and of plant data, to establish certain operating parameters.

Jan 1, 1993

By Jan A. Aune

The paper describes a number of electric furnace equipment modules especially developed or modified for slag furnace applications. Both the resulting design concept for a modern electric sulfide smelter and some of the changes in traditional process-concepts made possible are outlined.

Jan 1, 1983

By Viviane Tavares de Moraes, Denise Crocce Romano Espinosa, Jorge Alberto Soares Tenorio, Adriana Johanny Murcia Santanilla

"Increasing volumes of solid waste are generated worldwide, due to the continuous technological advances, the electronic scrap is part of these waste, requiring the study of recycling processes to stimulate this activity or the reuse of its components. The separation of nickel from sulphate leach solution, which also containing iron, zinc and aluminium was carried out using bis-(2,4,4-trimethylpentyl) phosphinic acid (Cyanex 272) as extractant, in order to determinate the effects of pH and temperature. The number of stages required for extraction was also assessed. The results showed that the metal extraction increased with increasing pH. On the other hand, increasing temperature was not favorable for all metals. However, under conditions used in this paper the purification of solution containing nickel was possible.IntroductionIncrease in the demand of metals in the world for use in industry causes a great exploration of natural resources. One outcome of this is increased investigations for the recovery of metals from industrial wastes. Nickel is found in wastes, such as batteries and electric and electronic devices, this kind of waste becomes a significant source for metals recovery. Since nickel is also present in printed circuit boards, which are associated with electric and electronic equipment, it can be recovered from this kind of waste through different techniques. It is important to highlight that iron is generally associated with this scrap [1] and for its removal chemical precipitation is often used. On the other hand, the solvent extraction process is widely used for treatment of leach liquors, because it can be produce high purity solutions [2, 3]. This technique is based on the purification of solution using contact between a liquor leaching and the immiscible organic solution, which contains an extractant that promotes the desired metal transfer [4]."

Jan 1, 2012

By W. K. Connor, O&apos

Thermal Treatment Technology Division Albany Research Center, U.S. Dept. of Energy Oregon. This evaluation included a characterization study and direct smelting tests conducted in a bench-scale electric arc furnace (EAF). In contrast to other thermal treatment technologies considered for these wastes (i.e., fluidized bed combustion), direct smelting in the EAF can process 100% of the wastes without prior beneficiation, and utilizes solid oxidant additions (in this case iron ore) rather than air to oxidize the carbon. This solid oxidant addition is advantageous because it results in the production of several value-added furnace products. These products include cast iron resulting from the reduction of the iron oxides, baghouse dust containing virtually all of the zinc from the residues, and a clean (nonhazardous) slag product suitable for recycle as concrete aggregate or construction fill. Offgas from the smelting furnace also holds potential as fuel gas for cogeneration. The direct smelting tests conducted thus far were successful at producing the desired furnace products, exhibiting the potential for complete recycle of the waste pile. A cast iron product of comparable quality to conventional cast irons was produced, at nearly 80% iron recovery to the metal. The slag product was determined to be nonhazardous, based on the EPA TCLP. Lead and zinc partitioning to the dust product was greater than 99%. The material balance over the furnace indicates that for every ton of feed processed, 540 lb. of cast iron, 600 lb. of slag, and 150 lb. of dust would be produced. Energy consumption was roughly 1.10 kWxh/lb of feed material. Prior experience suggests that these figures measured in the bench-scale furnace would translate to 0040 to 0.50 kWxh/lb at the industrial-scale.

Jan 1, 2000

By N. Pradhan, B. K. Mishra, B. D. Nayak, B. K. Mohapatra, R. K. Mohapatra

"Present study is about use of a group of Iron[Fe(III)] Reducing Bacteria (IRB) to convert the goethite (a-FeOOH) present in the original lateritic Nickel ore to magnetite under an anaerobic condition and subsequently release the bound Co(III) and Ni(II) through leaching. The lateritic Nickel ore contains 0.8% Ni, 0.049% Co, 1.92% Cr, 0.32% Mn and 50.2% Fe. An anaerobic dissimilatory Fe(III) reducing bacterial consortium capable of using acetate as carbon source (electron donor) and lateritic ore as terminal electron acceptor, changes the initial light brown color of the ore to dark brown. The change in color is due to the conversion of goethite to magnetite, which was confirmed by XRD. When the IRB treated sample was subjected to both bioleaching and acid leaching, it shows a greater recovery of Nickel and Cobalt values as compared to untreated original lateritic Ni ore. Further a magnetic separation method was used to separate the magnetic part of the treated lateritic ore and subjected to acid- and bio-leaching for better recovery of Nickel and Cobalt.IntroductionIt has been known that micro-organisms have the potential to reduce metals but more recent observations have shown that a diversity of specialist bacteria and archaea can use such activities to conserve energy for growth under anaerobic conditions [12]. Natural Fe(III) oxides are high in surface area and are reactive [1]. Fe (III) oxides adsorb a wide range of metal cations and anions by complexation to surface hydroxyl groups [17], and function as the primary redox buffering solid phase in many sediments and subsurface materials [5].Recently a number of bacteria have been isolated based on their ability to use metal ions, including Fe(III), as electron acceptor under anaerobic conditions. These are capable of producing energy by coupling the oxidation of organic compounds to reduction of Fe(III). Iron[Fe(III)]-Reducing Bacteria (IRB) have been isolated and identified from a wide variety of environments including freshwater and marine aquatic sediments and submerged soil [8]. The biogeochemical cycle of iron is linked to those of the trace metals, as many trace metals coassociate with Fe(III) oxides or reduced iron phases (e.g., magnetite, siderite, or iron sulfide). IRB can utilize Fe(III) oxides as terminal electron acceptors for respiration [18]; thereby reducing all or a fraction of the solid. The reductive portion of the iron biogeochemical cycle in non-phototropic environments (e.g., sediments and subsurface materials) is driven by the direct enzymatic reduction of Fe(III) oxides to Fe(II) by dissimilatory iron reducing bacteria [13,14]."

Jan 1, 2009

By M. J. Adam

The Bureau of Mines is investigating the feasibility of partitioning complex sulfide minerals to simpler sulfide phases by sulfidation reactions. Such partitioning can afford opportunity to improve selective extraction of mineral constituents of value. This report describes research involving sulfidation partitioning of byproduct chalcopyrite concentrates from Missouri lead ore processing, and a Utah chalcopyrite concentrate from Cu ore processing. Small chalcopyrite samples were sulfidized with elemental S in glass capsules sealed after evacuating and backfilling with He, by heating for 1 to 24 h at specific temperatures in the range of 250? to 500? C, extending from below to above the boiling point of S (-4450 C).

Jan 1, 1987

By Guangliang Wu, Dongchang Huang, Xinbin Liu

Oxidation Kinetics of SPHC was analyzed by TGA, and the curve of oxidation weight gain with different temperature was acquired. It is found that, when the oxidation temperature is between 500 and 600 , all the curves are linear; when the oxidation temperature is above 700 , the curves are close to parabolic. At the temperature of 900 , the oxidation weight gain increases dramatically. The TGA results indicate that the activation energy of SPHC steel is 146.19 kJ/mol at the temperature of 500 900 , and an oxidation kinetic model was set up for variable temperature. Based on the temperature change during rolling process, numerical simulation of oxide scales evolution was carried out for SPHC steel, and the simulation result agreed well with measured ones. It can provide a basis for estimating the scale growth and controlling the temperature on site.

Jan 1, 2016

By C. Landolt

Inco's Copper Cliff Smelter Complex produces some 11 5,000 tonnes per year of nickel and 120,000 tonnes per year of copper. The Smelter flowsheet has changed a number of times over the years. The most recent changes were effected in the mid-1980's in response to new realities in metal markets and heightened awareness about the workplace environment. By 1994, the flowsheet will undergo yet another metamorphosis as part of Inco's SO2 Abatement Program. The paper discusses the improvements implemented during the 1980's and projects the processing in the Smelter through 1994.

Jan 1, 1993

By J. J. Talja

An investigation of oxidation of various nickel concentrates was carried out using differential scanning calorimetry (DSC). The aim of this study was to determine the ignition temperature and investigate other oxidation behavior of various sulfide-based nickel concentrates. Variables in the experiments were mineralogy, particle size and partial pressure of oxygen with temperature increasing linearly at 25 K/min from 323 to 1023 K (50-750 °C). The igni¬tion temperature was determined to represent the starting point of rapid oxidation. The reac¬tion enthalpies of the concentrates were determined and the amount of heat generated up to various time were used to calculate the extent of reaction. Mineralogical changes at various stages of oxidation were also investigated. For this purpose a second set of DSC-experiments were carried out in which each experiment was interrupted at a desired temperature between 673-873 K. From these tests the weight loss of samples were determined and changes in the individual constituent of sulfide minerals were analyzed. For pentlandite-based Ni-concentrates the ignition temperature was 705-710 K (approximately 435 °C). Pyrite was the first sulfide to oxidize. Reactivity of the violarite-based concentrate was greater than those of the pentlandite-based concentrates. The stoi-chiometry of pentlandite changed before ignition because of preferential oxidation of iron. Rapid oxidation of the pentlandite mineral occurred at about 823 K (550 °C). By 900 K about 90 % of the iron in pentlandite was converted to hematite, and NiS containing some iron was formed.

Jan 1, 1994

By Marcio B. Fonseca

Nickel-cobalt laterite deposits have become the focus of attention for hydrometallurgical processing. Following the lessons of the second generation high pressure acid leach (HPAL) projects in Western Australia other Ni-Co laterite projects are now evaluating potential HPAL projects with a rigorous integrated approach that begins with geological modeling, resource estimation and metallurgical studies. The Vermelho nickel-cobalt laterite deposit has been under exploration and study for several years with investigations of various metallurgical processes. Recent HPAL studies have indicated that the nickel and cobalt laterite at this deposit is amenable to upgrading by silica rejection followed by pressure leaching. These studies have required a detailed geological investigation to generate a new resource model. The recent development of a sophisticated geological model integrated with a multi-element resource estimation for this complex tropical nickel laterite deposit in northern Brazil provides an example of the contribution of geology at the critical project stage where process technology decisions are made on relatively small samples of the total resource.\ Keywords: Ni Laterite, Geological Modeling, Resource Estimation

Jan 1, 2004

By Stanko Nikolic

The Top Submerged Lance (TSL) technology, developed in the 1970s, is now widely used for the processing of a range of materials. TSL technology for continuous converting was first patented in the 1990s. The process is based on the use of calcium ferrite slag. Although this slag system had been applied elsewhere the phase equilibria had not been thoroughly investigated. This lead to a collaboration between the Process Technology group of Mount Isa Mines, now part of Glencore, and the Pyrometallurgy Innovation Centre (PYROSEARCH) at The University of Queensland. Through multiple research programs this complex system was successfully investigated. The results were then implemented within thermodynamic modelling tools. This combined new knowledge was then applied to the design and industrial implementation of the TSL continuous converting technology, ISACONVERT™. This paper describes the key findings of the research and how this was applied to the industrial implementation of the technology.

By Shadia J. Ikhmayies

In this work the equilibrium temperature-composition phase diagrams of the Si-O2 system were calculated using Thermo-Calc software in the temperature range 500–3000 K. Constituents of stable phases were obtained, and the amounts of certain phases where investigated with the variations in the composition of oxygen and temperature. It is found that quartz with silicon represent a stable phase in the temperature range 500–1150 K, while tridymite with silicon represent a stable phase in the temperature range 1150–1700 K. A liquid phase is found besides tridymite in the temperature range 1700–1750 K, and a stable phase of cristobalite with liquid appears in the temperature range 1750–2000. The maximum amounts of quartz, tridymite, and cristobalite are found at oxygen mole percent of 67.7%.

Mar 1, 2017

By R. David Prengaman

During the past several years a new insoluble lead anode has been developed for copper electrowinning. The new anode consists of a rolled lead-calcium-tin alloy sheet attached to a slotted copper bus bar by a soldering process which produces a complete metallurgical bond between bar and sheet. The metallurgical bond greatly reduces the resistance between the bus bar and the lead sheet and the high conductivity does not deteriorate during the life of the anode. The rolled anode thins uniformly and does not suffer preferential grain boundary or internal corrosion commonly seen in cast anodes. The lead-calcium alloy containing a high tin content corrodes slowly because the rolling process produces a uniform, fine grained structure. The wrought product is very strong and ductile; and contains no internal defects, segregation, cracks, or pores which can reduce the life of the anode. Because the anodes corrode uniformly, a high percentage of the anode thickness can be utilized thus extending the life of the wrought anodes. The anode alloy composition which is stable only in wrought form, produces exceptional resistance to passivation during current interruptions. First introduced into liberator cells, the new electrowinning anodes have been specified as the anodes of choice for every new SX-EW tankhouse constructed in the last two years. This paper describes the new anode, its method of construction, service history, and how it differs from present copper electrowinning anodes.

Jan 1, 1987

By Jinrong Zhang

Major components of soil were tested for their ability to attenuate cyanide. Feldspar, kaolinite, plagioclase and bauxite are found to degrade cyanide at an appreciable amount mainly through adsorption. A soil near a mining site in northern Nevada was studied in detail using a tall column. Many species of cyanide were anlyzed to determine the mechanisms of the reactions of cyanide with soil. Volatilization, adsorption, oxidation, precipitation and complexing were quantitatively identified, being 5 to 10, 11.7, 4.2, 7.3 and 4 per cent of the total cyanide added, respectively. It is found that the oxidation of cyanide to cyanate is due to the catalytic effect of nickel and copper leached from the soil. Precipitation of metal-cyanide complexes occurred at low pH values.

Jan 1, 1991