Search Documents

By Olga Frank-Kamenetskaya

The experimental results of study of atmospheric corrosion processes on Saint-Petersburg bronze monuments surface, received in situ and by means of simulating experiments, have been discussed. Influence of the time factor on corrosion film (patina) mineral composition has been analyzed. Direct dependence between patina mineral composition and environmental conditions has been proved. The sequence of patina phases crystallization has been established. Effect of the chemical composition and heterogeneity of artistic bronze and also monument surface structure on the rate of corrosion process has been regarded. The time variations of mass of the crystallized in the hydrochloric acid vapor phases have been investigated. The kinetic laws of their development at the initial stage of formation, indicating simple (non chain) reactions, have been revealed.

Jan 1, 2006

By Reza Kamali, Mohsen Bashiri, Hadi Fanisalek

"Nomenclature: A: area (m2), C: heat capacity (WIK), cp: specific heat (J/Kg K), d: internal tube diameter (in), F: correction factor for multi-pass and crossflow heat exchanger, h: convective heat transfer coefficient (W/m2K), k: thermal conductivity (W/mK), L: length (m), m: mass flow rate (Kg/s), W: flow rate, N: number, Q: heat rate (W), R: thermal resistance, T: temperature (°C), U: overall heat transfer coefficient (W/m2K), ;1,,P: pressure drop (Pa), ;1,,T: temperature difference (°C), p: density (lb/ft3), N: number of tube passes, U,: velocity in tubes, iJh: head loss in feet of flowing fluid, Up: velocity in the pipe leading to and from the heat exchanger (ft/sec), µ: viscosity ( cp ), Llpf frictional pressure loss (psi/l 00 equivalent ft of pipe) Subscripts: b: baffle, c: cold, cf counter flow, ex: exchanger, f: fouling, h: hot, i: inlet-inner, ib: inlet baffle, lm: logarithmic mean, m: mean, o: outlet-outer, s: shell, t: tube, w: wall AbstractThe main bottleneck for primary aluminum production industry is dealing with a huge amount of input energy. The fact is that part of provided energy to aluminum production smelters will be lost as waste heat and it never used for aluminum production. One part of waste heat is escaping from the potroom exhaust gases, which was studied for possible recovery in a desalination plant to produce distilled water and the paper was presented in 2011 TMS Annual Meeting. However, it was shown that waste heat recovery plant to produce distilled water is highly profitable but the main fact is that the exhaust gases from potroom are highly corrosive, abrasive and dusty. The main challenge for desalination plant construction, which is using aluminum smelter exhaust gases as the main heat source, is the highly corrosive environment that makes the situation difficult and complicated for equipments design and plant construction. In this paper, we are trying to study a detailed investigation regarding the heat exchangers fouling, corrosion in heat exchangers including heat exchangers' material, how often we need to shut down the plant for maintenance or cleaning, and plant thermal efficiency with considering fouling."

Jan 1, 2012

By Yoji Imai, Akio Watanabe, Masakazu Mukaida

"To clarify the feasibility of alkoxides and acetylacetonates as precursors for laser CVD of metal oxides, vapors of tantalum or titanium alkoxides and zirconium acetylacetonate were irradiated by KrF excimer laser and deposits were characterized by XRD and XPS measurements. As for tantalum and titanium, non-stoichiometric crystalline oxides grew nearly phototropically, however, zirconium oxides deposited showed only halo-pattern by XRD measurements. Electric conductivity measurements of tantalum oxides implied the improvement of the insulating properties by the addition of activated oxygen to the ambient.IntroductionThere has been renewed increasing attention to the metallic oxide thin films because ofits promising usefulness in many applications, such as high-Tc superconductors and ferroelectric devices. A variety of thin film preparation techniques have been studied such as sputtering, chemical liquid deposition (sol-gel and metalorganic decomposition), pulsed laser deposition and chemical vapor deposition (CVD). Among them, we think CVD is the most promising method because it offers a high controllability of morphology and good step coverage at relatively high growth rate. Preparation of oxide films by CVD can be achieved using a precursor containing metallic element and oxygen containing gas such as N20 at the same time. However, metalorganic (MO) compounds which contain both metallic element and oxygen, directly bonded to metallic element, seems to be more favorable because some of MO has a good properties for CVD such as a rather high vapor pressure, stability in ambient and low toxicity."

Jan 1, 1998

By Chikabumi Yamauchi, Mitsuru Tanahashi, Tsuyoshi Taniguchi, Nobuo Furuta, Toshiharu Fujisawa

"It is essential to clarify the equilibrium relations among nonmetallic inclusions of the Mn0-SiO2-CrOx system and molten stainless steel in order to control non-metallic inclusions formed by the deoxidation of stainless steel with silicon. In the present study, the phase equilibria of the MnO-SiO2-CrOx system were measured by conducting the following experiments under controlled oxygen partial pressure, Po2, at 1873 K:1) Phase equilibria of the MnO-Cr20 3 binary system were measured for Po2 = 2 x 10-6 ~2 x 102 Pa.2) Phase equilibria of the MnO-SiO2-CrOx ternary system were measured for Po2 = 2 X 10-6 Pa.Based on the results, the phase diagram of this ternary system was established under the condition of the Si-deoxidation process of stainless steel (Po2 = 2 x 10-6 Pa and T = 1873 K).IntroductionAt the deoxidation stage in steelmaking process, generally multiple deoxidizers participate in deoxidation reactions, and the composition of deoxidation products ""non-metallic inclusions"" greatly varies depending on deoxidizing efoments and their contents. In order to control non-metallic inclusions formed by the refining process of steel, it is essential to clarify the equilibrium relations among non-metallic inclusions and molten steel.Especially, during the refining process of stainless steel, nonmetallic inclusions in molten steel seem to- change as follows. After the oxidation refining, Mn-chromite is formed in molten steel as non-metallic inclusion. By the deoxidation with silicon addition (mainly less than 1 mass%), Mn-chromite inclusions are changed their compositions to Mn-silicate. Segawa et al.[l] have reported the effect of amount of silicon addition on composition and mass ratio· of non-metallic inclusions during the Sideoxidation process of 18Cr-8Ni stainless steel at 1873 K, as shown in Figuri; L At higher silicon content than 0.5 mass%, only Mn-silicate was identified as non-metallic inclusion. On the other hand, at lower silicon content, both of Mn-chromite (MnO Cr2O 3) and Mn-silicate were identified. However, the thermodynamic and the kinetic analyses of the above-mentioned Sicdeoxidation process have not been made due to lack in the thermodynamic data for the non-metallic inclusions· of the MnO-SiO2-CrOx system, such as the phase diagrams, the activities of the components, and the free energy of intermediate compounds. In relation to the phase diagram of this system, those of the MnO-SiO2 [2] and the SiO2-Cr2O 3 [3] binary systems have been only reported"

Jan 1, 2000

By He De-wen

The influence of wastewater containing benzene from chemical industry by technology combined blow-off with Fenton reagent oxidation was experimentally studied. The present results suggest that the technology combined blow-off with Fenton reagent oxidation can effectively remove benzene pollutant in wastewater. The main factors that influence the removal benzene such as temperature and blowing time and volume, pH and reagent dosage of H2O2 and Fe2+ are studied and the optimal experimental conditions are as follows: time 20min, temperature 40i, air-blowing volume 0.4L/min, pH value 5, and H2O2 and Fe2+ dosage 2mL/L and 200mg/L respectively. Under the above conditions, benzene pollutant can be removed up to 97%. Compared to other removal ways of wastewater containing benzene, the technology combined blow-off with Fenton reagent oxidation is more effective and has the advantage of high speed.

Jan 1, 2009

By Daoxin Wu

In this paper, the rutile TiO2 were prepared under air, Ar and H2 calcination atmosphere by low temperature hydrolysis using Tetrabutyl titanate (C16H36O4Ti) as raw material. Powers were characterized by X-ray diffraction, UV-vis diffuse reflectance and X-ray photoelectron spectroscopy. The influence of the calcination atmosphere on the photocatalytic reactivity of rutile TiO2 for oxygen production was investigated. The photocatalytic reactivity of rutile TiO2 prepared under air, Ar and H2 atmosphere was compared under ultraviolet and visible light radiation with Fe3+ (c=8.0mmol.L-1) as electron acceptor. The results showed that rutile TiO2 prepared under Ar and H2 atmosphere had higher photocatalytic activity for oxygen production than that prepared under air atmosphere. The oxygen production rates under ultraviolet irradiation were 427.5, 378.2 and 357.0µmol.l-1h-1 respectively when rutile TiO2 was prepared under Ar, H2 and air atmosphere. The oxygen production rates under visible light irradiation were 78.2, 52.2 and 13.5µmol.l-1h-1 respectively when rutile TiO2 was prepared under Ar, H2 and air atmosphere.

Jan 1, 2008

By Chunhua Liao, Chao Peng, Guangsheng Huo

To get the separation of tungsten and molybdenum, we adjusted the pH of the solution to 7, at which tungstate (WO4 2-) will be polymerized into HW6O21 5-, while molybdate will still exist in the form of MoO4 2-. Two strongly basic anion exchange resins (D201, D213) were experimented for the separation of tungsten and molybdenum. The results of condition experiments indicate that D213 resin performs better in the treatment of lower concentration solution A (WO3 10g/L, Mo 4.12g/L) with a separation factor as high as 10.64. While D201 resin is more suitable for the high concentration solution B (WO3 70g/L, Mo 28.97g/L) with a separation factor of 6.9. The results of column testing performed on D213 resin show that the solution after loading process with a mass ratio of Mo/WO3 = 50 and the desorption solution with a mass ratio of WO3/Mo = 27 can be obtained

Jan 1, 2014

By Sang-Beom Lee

For thermodynamic prediction, the deoxidation equilibrium of aluminum in Fe-36%Ni alloy was studied with a cold crucible under Ar gas atmosphere at 1773K. For the deoxidation reaction in liquid Fe-36%Ni base, i.e.: A12O3(s) = 2A1 + 3O The interaction parameters and the equilibrium constant between aluminum and oxygen in liquid Fe-36%Ni alloy are given in the following: eo Al = -3.8, roA1=0.9, eAl° = -6.4, rAl° = 700, rAIAIo = 3.1, roA1o = 833 within the composition range of [Al] < 1 mass%. The temperature dependence of the equilibrium constant was obtained in the range of 1773K < T < 1973K by using reported data and present results as follows: log KAo= 0.58-24463.7 / T The deoxidation equilibrium with aluminum in Fe-36%Ni could be thermodynamically well described in the range up [Al] < 1 mass% with first and second order interaction parameters as well as the equilibrium constant determined in this study.

Jan 1, 2002

By Zongliang Zhang

Electrowinning is a significant step in metal extraction processes. Because the nature of electrowinning is to reduce metal from its oxidized state, substantial energy consumption accompanies it. Electrowinning processes of different metals have much in common—the deposition of the metal on the cathode and the counter-reaction on the anode. An advanced model was developed that can be applied to a variety of metal electrowinning processes. A model for specific metals can be readily obtained by modifying parameters such as potential, kinetics, and side reactions in the model. The model incorporates mass transfer, gas-liquid flow, electrochemistry, and deposition, making it a comprehensive electrowinning model. The model is applied to copper, nickel, and zinc and verified with the experimental results. In addition, the parameter settings and results of different metals were compared, showing that this model has great versatility and accuracy, thereby making it an efficient and effective research tool.

By Defeng Zhou, N. Trubaki, Jian Meng, Fanzhi Menga, Xiaojuan Liu, Yanjie Xia

"The microstructure and the electric conductivity of (Ce0.9Nd0.1)1 xMxO2 d (M=Mo, W) solid solutions were investigated. It has been found that their conductivity containing the grain (s gi ), the grain boundary (s gb) and the total conductivity (s t ) at 300°C- 700°C can be ranked as: (Ce 0. 9Nd 0. 1 ) 0.99 W 0.01 02- d (s gi = 0.065 S.cm·1, (s gb = 0.265 S.cm·1, s t = 0.039 S.cm-1) > (Ce0.9Nd0.1)0.99Mo0.01O2- d (s gi = 0.053 S.cm·1, s gb = 0.142 S.cm·1, s t = 0.029 S.cm-1) > Ce0.9Nd0.1 s 2- d (s gi 0.045 S.cm-1, s gb = 0.091 S.cm-1, s t = 0.018 S.cm-1) measured at 700°C. The highest conductivity is obtained in (Ceo.9Ndo.1)0.99W0.01O2 d. These results indicate that (Ceo.9Nd0.1)0.99W0.01O2- d is the most promising electrolyte materials of intermediate-temperature solid oxide fuel cells among (Ce0.9Nd0.1)1-xMxO2- d. IntroductionRare-earth (e.g. La3+, Nd3+, Gd3+ and Sm3l doped ceria-based ceramic materials have been acknowledged to be attractive electrolytes for solid oxide fuel cells operating below 600°C due to their high ionic conductivity [1, 2]. In order to improve ionic conductivity of these electrolytes further, in recent reports [3-6], some aids such as Mo03 [3] etc. in a limited amount can be used which causes extremely high conductivity. For example, Zhou et al. found that with MoO3 doping, the grain boundary conductivity of Nd3+ doped CeO2- d increased notably especially at lower temperatures due to the effect of severely undersized do pants [3]. It is well known that the size of W6+ (rw6+ = 0.60 Å) is close to Mo6+ (rMo6+ = 0.62A) because of lanthanide shrinkage. Thus, rare-earth doped ceria e.g. Nd3+ doped CeO2g with WO3 in a limited amount will be probably good and even better electrolytes. However, much less information is available about these materials. Therefore, in our paper, (Ce0.9Nd0.1)0.99 1-xMxO2- d (M=Mo, W) solid solutions have been prepared and characterized. Much higher conductive electrolytes are found in the series of (Ce0.9Nd0.1)0.99 M0.01O02- d particularly (Ce0.9Nd0.1)0.99W0.01O2- d"

Jan 1, 2012

By A. Arenas-Flores, Pandiyan Thangarasu, J. P. Hernández-Lara, F. R. Barrientos-Hernández, J. A. Romero-Serrano, A. Hernández-Ramírez, M. Pérez-Labra

BaTiO3 doped with Gd3+, was synthesized from BaCO3, TiO2, and Gd2O3 as powders using the solid state reaction method (Ba1-xGdxTi1-x/4O3). The milling of the precursors was performed in an agate mortar with acetone as control means and compositions x = 0.001, 0.005, 0.05, 0.15, 0.25, 0.35 Gd3+ (wt%). Firstly, the powder mixture was decarbonated at 900 °C for 8 h, after it was sintered at 1400 °C for 5 h. Tetragonality of synthesized BaTiO3 doped with Gd3+ was analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM) and Raman spectroscopy (RS). Subsequently, the powders sintered were uniaxially compacted cold until to obtain pellets of about 10 mm in diameter; which again were sintered at 1400 °C for 4 h. XRD patterns and Raman spectra results revealed that the crystal phase of the obtained particles was predominately tetragonal BaTiO3.

Mar 1, 2017

By T. E. Warner

In order to detect arsenic and antimony in zinc, various electrochemcial experiments were performed involving the electrochemical introduction of sodium atoms into molten zinc using a solid electrolyte. Under high rates, the formation of the intermetallic phase NaZn13 was assumed to form. Under more moderate injection rates of sodium, employing a symmetric "zinc/zinc cell", a qualitative relationship between the current generated during cyclic voltammeuy and the arsenic and antimony concentrations in molten zinc was observed.

Jan 1, 1999

By Lei Zhang, Shining Chen, Lina Wang, Pu Liu, Benquan Fu, Jiannyang Hwang

A three-dimensional (3D) electrode reactor combined with Fenton reagent was used for advanced treatment of coking wastewater from secondary biological treatment. Effects of some key factors on total organic carbon (TOC) removal rate were investigated, and the results were compared with those of the common three-dimensional electrode reactor. Experimental results showed that TOC removal rate could reach 51.7%, when optimal operating conditions were as follows: initial pH value 3.5, H2O2 dosage 17.6mmol/L, reaction time 90min and FeSO4·7H2O dosage 3.5mmol/L. Analytical results from UV absorption spectra indicated that the organic substances in the coking wastewater were well degraded by this system, which provided good experimental basis for the practical application of this process in the treatment of coking wastewater. This can be meaningful for the treatment of other kinds of wastewater.

Jan 1, 2015

By Motang Tang, Chaobo Tang, Shenghai Yang, Lulu Guo, Yun Li, Yongming Chen, Jing He

A new innovative process for one-step and cleaner extraction of lead from spent lead-acid battery by reductive sulfur-fixing smelting was presented. This paper summarized and discussed several potential sulfur-fixing agents and molten salts which can be used in this new technique. Thermodynamic analysis involving reaction mechanism, ΔGT and predominance-area diagrams of different smelting systems were performed, respectively. The results proved the technical feasibility and high-efficiency of this process. Copper oxide ash (CuO), zinc oxide ash (ZnO) and iron oxide bearing residues (FexOy) can be used as sulfur-fixing agent to extract lead through exchange reactions. Sulfur-fixed efficiency of CuO, ZnO and FeO decrease slightly in turn. Sulfur contained in PbSO4 is fixed in form of Cu2S, ZnS and FeS respectively which avoids SO2 emission. The addition of molten salt can significantly decrease temperature of reductive sulfur-fixing reactions. Molten salt can be regenerated and recycled in smelting system after filtering solid residues.

Mar 1, 2017

By D. Majuste

This paper describes an experimental approach to evaluate the effect of organic impurities or even additives on metal electrowinning and product quality. In addition to electrowinning tests and electrochemical measurements, the approach includes organic analysis by Fourier Transform Infrared spectroscopy and gas chromatography; video monitoring of the reaction interface; and product characterization by using scanning electron microscopy, crystallographic texture and bending tests. The mechanical behavior of metal cathodes was assessed with a customized bending device that is able to bend the cathodes up to angles similar to that of the stripping machine. In this work, the effect of a potential organic impurity, lubricating oil, on the production of electrolytic zinc is taken as a case study. The findings of the investigation allowed a better understanding on the role of this organic on energy consumption and product quality and a qualitative prediction for the behavior of Zn cathodes during the stripping operation. Simple control and optimization procedures resulted in significant energy savings.

By T. K. Mukherjee

The importance of the processing of secondary resources such as solid industrial wastes and liquid effuents as well as byroducts for the recovery of the associated metal values hardly needs any elaboration. Such processing contributes in no small measure.towards the augmentation of the availability and the supply position of resources. As an added benefit, it leads to a reduction in environmental pollution caused by the undesirable waste materials. As some typical examples of secondary resources in the Indian scenario, mention&apos; can be made of spent catalysts, metal/alloy scrap, ash, consumed batteries, flue dust, slag, sludge and slime, pickling solutions, spent acids; plating rinse solutions, spent etchants, waste water from synthetic fibre manufacture and from tanneries etc. These wastes constitute a source of a variety of non ferrous metals. In the processing of secondary resources like these, the techniques of hydrometallurgy such as solvent extraction play a pivotal role. This paper outlines the efforts made to use solvent extraction to recover (1) base metals such as copper, zinc, nickel and cobalt from a number of secondary resources like cake, and sludge(2) refractory metals like molybdenum and vanadium from sulphidic, byproducts and spent catalyst and (3:) nuclear metal like uranium from phosphoric acid. In the case of base metals, process flowsheet involving the use of acidic extractants such as DEHPA and PC88A have been optimised. The problem of iron removal from the leach liquor, "which influences the metal recovery process significantly, has drawn a special emphasis. hi the case of refractory metals, basic extractants .like Alamine 336 has been pressed into service to produce kilogramme. quantities of pure salts of molybdenum and vanadium, Finally, the paper gives a brief account of plant experience in recovering uranium from phosphoric acid, using &apos;a solvent system comosed of DEHPA and TOPO.

Jan 1, 1996

By Feng Wang, Guojing Shi, Yangyang Xie, Zizong Zhu, Qiang Wu

The coal chars from northwestern part of China are characterized with high reactivity and low strength after reaction. Four type of coke-making coals selected from northwestern part of China were studied by proximate analysis, ultimate analysis, vitrinite reflectance analysis, and FTIR with curve-fitting analysis to obtain information on their chemical composition and chemical structure. The results show that the studied coals have relatively high values of final contraction of coke residue index (x) and relatively low values of maximum thickness of plastic layer (y) and average vitrinite reflectance. Based on the curve-fitting analysis of FTIR spectra, the aliphatic carbon (Cal), the aromatic carbon (Car), and the molecular structural parameters such as CH2/CH3, fa, Hal/Har, and (R/C)u are determined. The results of curve-fitting analysis indicate that the studied coals are characterized by a large amount of oxygen-containing functional groups and aliphatic side chains.

Mar 1, 2018

By Victor Bredykhin

The reasons of formation low quality cathode deposits and conditions of the anode passivation in electrorefining of copper silver alloys with increased (more then 5%) silver content in electrolyte, g/l: Cu - 40; H2SO4-50; 150 and 250; T= 401C have been investigated. As it is shown, increased acidity, anodic current density and silver content in anodes favor passivation. The assumption is made that the ingress of silver on cathodeis the most probable reason of growing dendrites on cathode. We have determined that addition of ethylene carbonic acid to electrolyte in the amount of 3,5 ÷ 10 ml/l suppresses the dendrite formation.

Jan 1, 2006

By S. Ozbilen, B. Erdogan, M. Erdogan

To study by thermal analyses the response of precipitation hardenable alloys of Al-Cu-Mg and Al-Li-Cu-Mg system to natural and artificial ageing, a series of ternary and quaternary Al-alloys with nominal compositions of Al-l.13wt%Cu-0:65wt%Mg (alloy-I), Al-1.15wt%Cu-0.57wt%Mg-0.07wt%Li (alloy-2), Al-l.19wt%Cu-0.56wt%Mg-0.75wt%Li (alloy-3), Al-2.0lwt%Cu-0.89wt%Mg (alloy-4), Al-2.14wt%Cu"0.56wt%Mg-0.07wt%Li (alloy-5) were used in the present investigation. Samples in the form of rolled sheets are subjected to water quenching at 25EC after solution treatment at 530EC for 20 min. Alloys were aged naturally at room temperature (25EC) up to 2 months and artificially at 190EC up to 2 days. By using differential scanning calorimetry (DSC) in the temperature range of25-300EC, differential thermal analysis (DTA) in the temperature range of25-600EC together with Vicker's hardness measurements, the response to natural and artificial ageing of the alloys used in the present study were investigated. It was observed that in these alloys, GPB(Cu, Mg) zones [Guinier-Preston zones with Cu and Mg] do form during water quenching at 20EC following solutionizing heat treatment. Natural ageing of the same alloys causes formation of more GPB(Cu, Mg) zones, which results in hardening in the alloys. Artificial ageing at 190EC up to l day results in GPB zone dissolution causing preliminary decrease in hardness values while two days of artificial ageing in the alloys cause S' (Al2CuMg) precipitation confirmed by DSC/DTA analyses resulting in an increase in hardness values. Li addition up to 0.75wt% helps T1 (Al2CuLi) and T 2 (Al6CuLi3) phase formation together with S' precipitation as DSC/DTA analyses show after the same heat treatment.

Jan 1, 1998

By Sergio N. Monteiro

Polymeric composites reinforced with natural fibers are increasingly been used in several engineering applications, from automotive parts to building construction elements. In addition to the relatively low cost, the natural fibers are also appraised by their renewable and biodegradable characteristics. Fibers extracted from the crust of coconut fruits, also known as coir fibers have been investigated for a possible use in composite materials. In the present work, the coirfiber/polyester matrix interfacial strength was evaluated by means of pullout tests. The variation of the pullout tensile stress vs. the embedded coir fiber length permitted to determine the critical fiber length and, thus, to calculate the interfacial strength. Observations by SEM complemented the results from pullout tests, indicating that coir fibers have a potential for application aspolymeric composites that could replace conventional materials such as wooden and gypsumpanels.

Jan 1, 2006