Search Documents

By Osamu Takai, Yoshiki Sato, Nobuhiro Tajima, Hiroyuki Sugimura

"Amorphous carbon thin films doped with nitrogen ( a-C:N) have been synthesized by means of shielded arc ion plating (SAIP). Their electron field emission properties, that is, threshold field strengths for electron emission and maximum emission current densities, were evaluated and compared with those of pure amorphous carbon (a-C) films prepared by the same SAIP apparatus. Among all of the fabricated a-C:N films, the a-C:N films with a N concentration of 23 %, which prepared using Nz arc plasm at a pressure of 1 Pa with applying a sample bias voltage of -100 V, showed the lowest threshold filed of 13.4 V/µm and the highest emission current density of 1.87 µAfcm2 at a field of20 V/µm. These field emission properties of the a-C:N film were much better than those of the a-C films. The best results obtained on the a-C film in this study were the lowest threshold filed of 15.5 V/µm and the highest emission current density of 0.052 µA/cm2 at a field of 20 V /µm. Nitrogen doping to aC was found to be effective for lowering threshold voltage for field emission and for increasing emission current density. The electron field emission characteristics of the a-C:N films depended not only on N concentration but also on chemical bonding state of nitrogen in the a-C:N films. The presence of the ~-C3N4-like phase, which contributes to improve wear resistance of a-C:N as well, distinguished by the NlsXPS peak at 400.5 eV is proved to be crucial in order to enhance field emission properties of a-C:N.IntroductionThere has been much interest in electron field emission from a cold cathode due to its potential applications in vacuum microelectronic devices including field emission displays which are expected as flat panel displays in next generation [l]. It is well known that efficient emission can be rather readily realized using tip-like shape cathodes, e.g., microfabricated three-dimensional electrodes [2], carbon nanotubes [3-5], etc. However, electron emission from planar surfaces is of particular importance since such a type of cathode is· simply fabricated and assembled into microelectronic circuits. Currently, amorphous carbon thin films doped with nitrogen (a-C:N) prepared by plasma processes have attracted attention because their threshold voltages of field emission are relatively low [6]. Among various methods for preparing a-C:N films, the process using arc plasma is of special interest since, in arc plasma, nitrogen is highly activated and new types of carbon nitride phase are expected to be synthesized. However, field emission properties of a-C:N prepared by arc plasma have been studied in less detail compared with that prepared by the other methods such as sputtering."

Jan 1, 2000

By Samantha Moodley, Rauf Hurman Eric, Cevat Kucukkaragoz, Aditya Kale

"Two titania slags, rutile and synthetic rutile were chlorinated with petroleum coke and CO in a small bubbling fluidized bed reactor. The study aims to identify differences in chlorination mechanism, compare conversion rates, blowover and the chlorination of impurities for the various titania feedstocks at different temperatures.Chlorination rates were highest at 1000ºC; rutile chlorination significantly increases as temperature increases from 800ºC to 1000ºC. At 1000ºC, synthetic rutile had the highest chlorination conversion rate; this was followed by Slag B which in turn was more reactive than Slag A and rutile. The mechanism for slag, synthetic rutile (SR) and rutile chlorination differs. Synthetic rutile feed is porous, providing a larger surface area for the chlorination reaction, hence the highest conversion rates was attained. Titania slag becomes porous with the initial chlorination of FeO and MnO whilst rutile remains solid. As the porosity of slag particles increases so does its tendency to be elutriated. Ti2O3 is oxidized within the early stages of chlorination during the chlorination of FeO and MnO. Ti2O3 not oxidized is then rapidly chlorinated.IntroductionTitanium dioxide (TiO2) is the most common compound of titanium, about 95 - 98% of extracted titanium minerals is processed into TiO2 white pigment [1]. Two processing routes exist for the production of TiO2 pigments, i.e., sulphate and chloride based processes. In the chloride process, titania feedstock is fed to a fluidized bed reactor together with reductant and chlorine gas. A temperature of 1000 - 1300ºC is maintained in the reaction zone and apart from silica, zirconia, uranium and thorium, virtually all the metal oxides in the feed are converted to their respective chlorides [2]. Chlorine is recovered and recycled back to the reactor."

Jan 1, 2012

By A. F. Kaczmarek

Cerro Negro is an undeveloped ore body located at the Cerro Verde mine near Arequipa, Peru. The mineable reserve contains 70 Mt of oxide ore grading 0.532% copper. Mineralization is hosted in three distinct rock types: tourmaline breccia, crackle breccia and granodiorite. Rock type effects copper recovery and acid consumption. The paper describes Cyprus' testwork philosophy and the resulting four-phase metallurgical program used to define the commercial leaching parameters. Copper recovery and acid consumption were monitored as functions of crush size, heap height, irrigation rate and acidulation conditions. Single lift, on-off and permanent multi-lift heaps were considered. Leach cycle times were based on incremental copper extraction and acid consumption rates, with added constraints imposed by operational requirements. The optimum leach system involves an on-off pad using tertiary crushed ore acidulated with 20 kg/t acid and stacked to a height of 6.5 m. The active leach cycle is 82 days at an irrigation rate of 0.26 l/min/m2. Under these conditions copper recovery is expected to average 81% over the life of the mine.

Jan 1, 1999

By C. Cheung, U. Erb

"Over the past few years, nano-processing of magnetic materials has received considerable attention, because many magnetic and other application-specific properties have been shown to be enhanced in materials with ultrafine grain size. This paper reviews recent advances in the production of nano-processed soft magnetic materials such as pure nickel and cobalt as well as binary nickel-iron and ternary nickel-iron-chromium alloys by electrodeposition. Magnetic, electrical and mechanical properties of these materials are presented and discussed in terms of their microstructural defects.IntroductionIn recent years, nano-processing of materials to enhance their magnetic properties has received considerable attention [1-23]. Thin films, compositionally modulated thin films, granular films and bulk materials have been produced by many different techniques. These include gascondensation [1-6], ball-milling [7,8], chemical processing [9,10], metal-organo complex routes, solution reduction and co-precipitation [11], sol-gel methods [12], sputtering [12-14], rapid solidification [15], devitrification of amorphous alloys [16-19] and electrodeposition [12,20,21]. The potential application of nano-engineered materials with enhanced magnetic properties has been specifically discussed for soft magnets [18,19,22,23], hard permanent magnets [15] as well as for layered materials showing giant magnetoresistance effects [13,14] and nano-composites for magnetic refrigeration [11,12].The purpose of the present paper is to review recent advances in the development of nanocrystalline soft magnetic materials by electrodeposition methods. These materials could find applications in areas such as magnetic recording heads, high efficiency electric motors, transformer cores, etc."

Jan 1, 1994

In this study, the method of chemical co-precipitation?reduction?diffusion was developed for the preparation of magnetic SmCo5 alloy. In the chemical co-precipitation process, the effects of solution pH, the reactant concentration, the dispersant on the process were investigated. The optimum conditions of the process were determined, and the SmCo5 alloy oxide precursor particles with fine crystalline structure, narrow size distribution was obtained. Then, by reduction-diffusion treatment of the precursor particles, the SmCo5 alloy with high quality was produced. It is anticipated that the co-precipitation-reduction-diffusion is a novel method available for SmCo5 alloy production.

Jan 1, 2006

By Joni M. Barnes

A strain of Pseudomonas stutzeri isohted from selenium contaminated surface waters, was found to be effective . in reducing selenate (Se04 2) stoichiometrically to selenite (Se03 2 '), which was further reduced to elementaJ selenium (Se0 ). These reactions were concurrent with the microbial oxidation of lactate. In order to assess quantitatively the amounts of seilenate and selenitein solution, improvements to existing analytical methods (ion exchange chromatography and inductively coupled plasma atomic emission spectrophotometry technique) .were made.

Jan 1, 1991

By T. Watanabe, T. Fujiwara, S-Wan Song, Y. Nakagawa, R. Teranishi, M. Yoshimura

"We have tried a new method to fabricate cobalt oxide films onto porous films directly by an electrodeposition method at low temperature. The porous substrate films (membrane-filters and paper) were placed between a LiOH solution and a CoSO4 solution and treated under electricalcurrents of ~1 mA/cm2 using carbon cathode and anode. Effects of temperatures, flow rates and electrical currents have been investigated. As a result, we found that the LiCoO2 films and Co3O4 films were successfully fabricated on paper and/or porous PTFE filters at 120 °C, while CoOOH films were deposited at 80 °C. Furthermore, LiCoO2 films did not cover whole the substrates, but was fabricated just over the anode. The chemical reactions of electrodeposition were also considered from these results.IntroductionRecent agreements on global environment require rapid progress of low energy and low waste processings for the fabrication of thin films that succeed to the mass production with the high consumption of the fossil fuels (such as physical vapor deposition°, chemical vapor deposition2), dip coating with firing3) etc.). The total energy consumption in aqueous systems should be the lowest among all these processing routes, because a much lager excess of energy is necessary to create melts, vapor, gas, or plasma than to form an aqueous solution at the same temperature4)The ""Soft Solution-Process"" (SSP) was one of the best concepts to realize the low energy and low waste fabrication of inorganic materials. 5) Generally speaking, SSP gives similar results to any other processing using fluids (such as vapor, gas plasma) and/or beam/vacuum processing. However, the total energy consumption of all these possessing routes should be the lowest in aqueous systems, because a much larger excess of energy is necessary to create melts, vapor, gas or plasma than to form an aqueous solution at the same temperature (Fig. 1). This idea can be easily demonstrated, using the simple example of BaTiO3. The energy diagram for the formation of BaTiO3 from various precursors is shown in reference 4. The driving forces (AG) for representative synthesis reaction of (1), (2), (3), (4) and(5) are 38, 727, 3685, 17 and —14kcal/mol, respectively at room temperature. 6' 7"

Jan 1, 2000

By Dachun Liu, Lei Shi, Yongnian Dai, Bin Yang, Yang Tian, Tao Qu

The carbonthermal reduction of high Mg–Si nickel laterite was studied under vacuum. The effects of adding calcium oxide and the reducing agent on the reduction of silicon in residue were studied at pressures of 10–200 Pa and different temperatures, with varying proportions of carbon and CaO. The analysis of the residue was performed using X-ray diffraction and chemical composition analysis. The results show the following: At 1350 °C with a C/O ratio of 1.5:1, the recovery of Si reached a maximum 71.09%. Under these conditions, Si exists mainly in the forms of Fe3Si, Fe2Si, FeSi and SiC. The recovery of Si was above 80% when the temperature was 1450 °C, the C/O ratio 1:1, and 15% addition of CaO. When CaO addition was 22.61%, all of the solid phase was Ca2SiO4.

Mar 1, 2017

By Ramana G. Reddy, Yudong Li

Numerical modeling of the thermal plasma process was carried out based on the thermal plasma reactor in our lab and confirmed using experimental data. The inlet boundary conditions of a non-transferred DC arc thermal plasma reactor were used in modeling the temperature and fluid flow distribution in the reactor. Different mesh grid sizes were used to confirm the model is independent of grid size. Temperature profile and gas flow distribution in the thermal plasma reactor were developed by the computational fluid dynamics (CFD) with ANSYS Fluent. The predicted temperatures are in good agreement with the experimentally measured temperatures in the reactor. The influence of plasma torch input power as well as the plasma gas flux on the temperature distribution was investigated using this model. The influence of power input and gas flow rate on temperature and velocity distributions are not independent. Generally, higher power input and lower gas flow rate will give rise to the temperature increase in the reactor.

Mar 1, 2017

By Paul E. Queneau

The QS (Queneau-Schuhmann) copper converter is a gently sloped, stepped, horizontal kiln-type tilting reactor in which desired bath oxygen activity, compositional and temperature gradients are created by countercurrent flow of matte and slag phases through a series of controlled bubble plume, mixer-settler configurations. Flow of gas and slag is normally concurrent. Copper sulfide concentrates are top-fed, employing oxygen flash burners. Oxygen and oxygen-carbonaceous fuel mixtures are bottom-blown into the smelting bath through judiciously located, independently regulated submerged injectors. Composition and mass flow rates of injector inputs are controlled to produce bubble plumes of desired character, without jetting through and out of the bath. The mixer-settler pattern can be reinforced if desired by employment of suspended shallow baffles. State-of-the-art instrumentation provides timely information required to govern key process variables. The outstanding capabilities of the QS converter for coppermaking have now been indicated by the current success of industrial QSL (Queneau-Schuhmann-Lurgi) leadmaking reactors. Modified converter designs are employed for leadmaking, nickelmaking and steelmaking.

Jan 1, 1993

By Y. F. Liang

Fe-6.5wt.%Si alloy has excellent soft magnetic properties compared with conventional silicon steel. It is very brittle at room temperature due to appearance of ordered phases, like B2 and DO3. In this paper, we investigate the effect of ordering on cold workability of this alloy. Methods of rapid quenching and hot rolling were utilized. It is found that rapid quenching and proper heat treatment of the hot rolled sheet could decrease the degree of order due to the very high solidification rate and high cooling rate. The rapid quenched sheet and hot rolled sheet after proper heat treatment could be cold rolled without crack. Microstructure, phase ordering, micro hardness, and cold rolling properties were investigated by Optical Microscope, X-ray Diffraction, Micro Hardness Indenter and Four-high Mill.

Jan 1, 2009

By Rak-lun Choi

Plasma-induced damage of InGaN/GaN multiple quantum well (MQW) light-emitting diodes (LEDs) has been studied in terms of forward turn-on and reverse breakdown voltages, together with etch rate and surface morphology. The physical degradation of sidewall along with rough surface morphology of n-GaN caused by increased ion scattering induced the deterioration of the forward and reverse voltages. It was found that the turn-on voltage is sensitive to the surface roughness of the etched n-GaN and the breakdown voltage is strongly affected by the sidewall contamination. Annealing under nitrogen after the mesa etching improved the electrical properties of the InGaN/GaN MQW LEDs. Efficient blue light-emitting diodes (LEDs) were fabricated using InGaN/GaN triangular MQWs. The LEDs with triangular QWs showed a lower operation voltage and 2.4 times higher light output power than those with the rectangular MQW LEDs at 20 mA and 20 °C. The intensity of electroluminescence (EL) at 20 mA was almost independent of ambient temperature in the triangular QW LED, but decreased substantially in the rectangular one.

Jan 1, 2003

By R. Luo, R. V. Kumar

"The co-deposition of cobalt and nickel as a binary alloy has been studied by both cyclic voltammetry and long-period controlled-potential electrolysis. Cyclic voltammetry experiments showed that the cathodic current density for the mixed Co-Ni (Co-Ni=1:3) electrolyte is noticeably higher than that obtained on electrolyte containing single CO2+ or Ni2+ (II) salt of the same ionic strength. The onset potential observed for the mixed salts electrolyte was also less cathodic (negative) than that for the single metal salts, respectively. The effects of a number of operational and compositional parameters on the co-deposition of cobalt and nickel were studied. The parameters under investigation include cathode (deposition) potential, temperature, CI-/Sol ratio in the electrolyte, the amount of additives such as H3B03, and acidity of the electrolyte.Optimum operational conditions were established for the deposition of cobalt and nickel binary alloy. These results are discussed with respect to feasibility of reclaiming cobalt, nickel and chromium from mixed superalloy scraps by melt-refining (under nitrogen and/or ammonia), followed by electrorerining of cast anode for co-depositing Co/Ni and thermal decomposition of chromium nitride for recovering chromium metal."

Jan 1, 1997

By Cheng Pan, Qiugang Yuan, Xuewei Lv, Mei Liu, Enguang Guo

Land-based nickel resources include nickel sulfide and nickel laterite. With the consumption of high grade nickel sulfide, use of nickel laterite has received more and more attention. The mineralogy and sintering behavior of limonitic nickel laterite with high iron and low nickel and silica was studied to offer technical support for producing ferronickel through sintering–blast furnace route. The mineralogy results showed that the main phases in this kind of nickel laterite are goethite (FeO(OH)), gibbsite (Al(OH)3) and NiFe2O4. The TGA (Thermogravimetric Analysis) and DSC (Differential Scanning Calorimetry) revealed hydroxide minerals in addition to absorbed water. After the sintering experiments the chemical composition, phases present (XRD analysis) and physical properties of the sinter were studied. The content of FeO in the sinter increased with increasing basicity up to 1.3, and then decreased with further increase in basicity. The yield of sinter increased (from 73% to 80%) with increase in the basicity from 1.1 to 1.7, and then the yield decreased with the further increase in basicity. Mg(Ni)(Fe,Al)2O4 is the main phase in the sinter while MgCaSiO4 and Fe2SiO4 is the main binder phase when the basicity is 1.1~1.5, and MgCaSiO4, Fe2SiO4 and SFCA is the main binder phase when the basicity is 1.7~2.1.

Jan 1, 2014

By T. T. Chen, J. E. Dutrizac

"Grooved cast Pb-Ag anodes are used by some zinc refineries to improve current efficiency. It was found that the manganese oxide scale formed on a grooved Pb-0.75% Ag anode consists mainly of MnO2, which occurs characteristically in rhythmically banded colloform structures and adheres to a layer of ""Pb02+PbS04"" that oxidized from the anode. The relatively homogeneous and nearly fracture-free morphology of the ""Pb02+PbS04"" layer suggests the relatively uniform corrosion of the anode. Deposition of the Mn oxide initially follows the contours of the anode surface, but the grooves eventually become filled with Mn oxide and gypsum. Hydrous Mn oxides and amorphous Mn oxides are believed to be also present in the manganese oxide scale. Tiny particles of PbS04 and SrS04, together with gypsum, other impurities and micro-pores, tend to concentrate in the grooves.IntroductionManganese is a common impurity in hydrometallurgical zinc processing circuits. The manganese originates from sphalerite (Zn,Fe,Mn)S and from the Mn02 added to the leaching circuit to oxidize ferrous ions [1]. Manganese in the sphalerite follows Zn through the roasting, leaching and purification processes, and is present as Mn(II) in the purified ZnS04 solution. The Mn in the added Mn02 is reduced to Mn(II) during the oxidation of the ferrous ions present in the leach solutions. In both cases, MnS04 is generated, and the MnS04 accumulates in the purified solution. In the cellhouse, Zn is plated at the cathodes to produce high quality metal. The Mn(II) is partly oxidized at the anode surface to Mn(IV), and the Mn(IV) precipitates as a scale on the surface of the anode and as a sludge on the bottom of the electrolysis cells. The presence of a thin layer of manganese oxide scale on the surface of the Pb-Ag anode can minimize the corrosion of lead and, accordingly, reduce the contamination of the electrodeposited zinc. However, a heavy manganese scale build-up can cause ""staining"" of the zinc deposits and reduced current efficiencies. Consequently, periodic anode cleaning to remove excess manganese oxide scale is carried out routinely in commercial operations."

Jan 1, 2011

By S. M. Copley, M. Yankova, E. Y. Yankov, J. A. Todd

"Nanophased coupled growth structures, with spacings of -10 nm, have been observed in banded microstructures produced by laser melting hypoeutectic Ag-Cu alloys. These coupled growth structures comprised a Cu-rich phase of width - 1 nm and a Ag-rich phase of width - 9 nm. In this paper, microstructural observations of nanophased coupled growth structures in hypo eutectic AgCu alloys are presented. Laser beam velocities for the transition from banded to microsegregation free microstructures are modelled and compared with experimental values. Models are presented to show that, at a critical undercooling, initial growth of a Ag-rich, metastable, extended solid solution is rapid but slows to a halt as copper is partitioned into the liquid at the solid/liquid interface. Following nucleation, the coupled growth structure then grows until the partitioned copper is consumed, at which point growth of the Ag-rich solid solution is again accelerated. This cycle then repeats resulting in banded microstructures comprised of 750 nm of the Ag-rich extended, metastable solid solution, followed by 250 nm of the coupled growth structure.1. Structural Studies of Laser Melted and Resolidified TrailsPresented here are observations of laser melted and resolidified trails in Ag-Cu alloys obtained at beam velocities ranging from 0.7 to 34 cm S·I. When the laser beam is scanned along the surface (positive x-direction) with a velocity Vb a melt pool with the shape given in Fig. 1a moves with the beam. The isotherms move with the velocity, Vi,. = Vb cos.p. Calculations employing the thermal analysis of Kou, Hsu and Mehrabian [1] for the beam velocities of this investigation and for the thermal properties of AgCu alloys, indicated that, .p, the angle between the isotherm velocity and beam velocity should be small at the surface where microstructural studies were made. This prediction was supported by observations of trail cross-sections. Based on these observations, and the calculations which include latent heat effects, the isotherm velocity for observations near the surface in our investigation was taken to be 27 cm S-I."

Jan 1, 1994

By A. R. Kiani-Rashid

In this paper, the effect of aluminum content on the formation mechanism, volume fraction, morphology and particle size distribution of graphite has been investigated. Addition of aluminum on ductile iron causes some fundamental changes in iron-carbon phase-diagram and as a result, improves the graphite formation during eutectic transformation. The results reveals that aluminum compounds have been formed in the core of graphite nodules, thus aluminum plays an important role in the formation of graphite nodules. Furthermore, it is indicated that an increase in the aluminum content also leads to an increase in the number of graphite nodules and a decrease in the nodules size. By using EPMA, the segregation of aluminum and silicon between graphite nodules has been studied

Jan 1, 2010

By P. F. Kerr

This is not a conventional professional paper. It deals mostly with personal experiences. These concern a background in applied mineralogy. Your committee asked me to do this. I accepted with a California enthusiasm which has since diminished with the approach of a Chicago winter. Nevertheless, I wish to thank your committee and also to apologize in advance for omissions and inadequate statements, as such a paper must possess. My introduction to applied mineralogy took place in 1922 at Stanford University. Physicists had recently demonstrated that crystalline powders would reflect x-rays in a systematic manner. Professor A.F. Rogers sug¬gested that significant x-ray reflections might be obtained from powdered opaque minerals. With the aid of Professor D.L. Webster in the Physics Department, I constructed an x-ray diffraction outfit. It was a crude affair, but it worked. Starting with 1924, we secured recognizable patterns of a goodly number of ore minerals (1,2,3). Today x-ray diffraction outfits are common, and a card system of mineral identification is constantly used.

Jan 1, 1981

By Faustino G. Prado

In the, quest for an economical and environmentally friendly reclamation of metallurgical dusts generated during pyrometallurgical operations, our goal has been the separation and recovery of most of the components, as well as the complete recycle of all the reagents. Effluents have been avoided, within acceptable economic parameters. This presentation, which can be applied to a large spectrum of dusts and other residual-materials-, has focused on the dusts generated by the operation of Secondary Copper Smelters. Those dusts show a wide range of components, including zinc, lead-, copper, cadmium, tin, chlorine and-alkalies. Our present work deals with the use of ammonium salts in the separation and recovery of-the above mentioned elements in a marketable form. Most of the chemistry and techniques involved have teen already confirmed in commercial scale operations. Others have gone through pilot scale tests or bench scale tests. The recycle of reagents has also been- confirmed at the same operating levels. A preliminary evaluation indicates that the chosen route, in addition to a viable economy, offers a complete and safe reclamation within the most strict environmental regulations.

Jan 1, 1995

By Minjun Tang, Jianfeng Zhou, Linjiang Qing, Yufeng Guo, Tao Jiang

"For the comprehensive recovery ofV, Ti, Fe in vanadium-titanium magnetite in the process of pre-reduction-electric furnace smelting, it is expected that vanadium oxide is reduced into molten iron and titanium oxide is available in the slag. Thus the effect of slag basicity, the content of MgO, MnO and CaF 2 of slag content on the separation of slag and molten iron and the comprehensive recovery of V, Ti, Fe were investigated. The results show that increasing slag basicity, MgO, MnO and CaF2 are all beneficial to the separation of slag and molten iron. Higher slag basicity and the addition of CaF2 strengthen the reduction of vanadium oxide, and inhibite the reduction of titanium oxide, which are in favour of the recovery ofV and Ti. However, the addition ofMgO, MnO was not efficient for the comprehensive recovery ofV, Ti, Fe. For the vanadium-titanium magnetite of Panxi in China, the recovery of Fe was over 98%, the recovery ofV in molten iron was over 85% and the Ti02 content in slag was about 43% under the optimal conditions of slag phase type.IntroductionIt is well known that there are abundant vanadium-titanium magnetite resources which are located in Panzhihua of Sichuan Province[!]. At present the vananium-titanium magnetite concentrates are smelted in the blast furnace, which just make use of iron and vanadium, but lots of titanium is discarded in the slag. At the same time, the process has a large number of disadvantages, such as low recovery of vanadium, long route, pollutions, large investment and expenditure of energy[2-3]. In recent years, in order to efficiently utilize the vanadium-titanium magnetite concentrates, several new non-blast furnace processes have been proposed, such as pre-reduction-electric furnace, pre-reduction-grinding separation and so on[4]. Especially pre-reduction-electric furnace is operating well in South Africa and New Zealand,However,Du to the high slag basicity of the slag, the grade ofTi02 of slag is Corresponding author:Minjun Tang.E-mail:450435123@qq.com. Tel:13627429224."

Jan 1, 2013