Search Documents

By Isabela Leao Amaral da Silva, Felipe Perisse Duarte Lopes, Alice Barreto Bevitori, Sergio Neves Monteiro, Ruben Sanchez Rodriguez

"The fibers extracted from the stem of the ramie plant are among the strongest natural lignocellulosic fibers with a potential to be used as reinforcement of polymer matrix composites. Characterization of the ramie fiber has recently been conducted for its physical and mechanical properties. However, the effect of increasing temperature on the ramie fiber behavior has not yet been fully investigated. Therefore, the objective of this work was to perform a thermal analysis on ramie fibers with different diameters within the naturally found range of practical interest. The analysis was conducted by thermo-gravimetric, TGA and DTG, as well as differential scanning calorimetric, DSC, techniques. It was found that the ramie fibers present thermal stability up to 200°C and then suffer a sharp deterioration between 300 and 500°C, resulting in characteristic peaks.IntroductionSince the middle of last century, polymer composites have substituted many conventional monolithic materials in applications ranging from aerospace to sport [l]. The main advantages of these composites are the low density and flexible properties specially using fiber as reinforcement to suit the mechanical performance requirements [2]. These are usually high strength and stiffness requirements that could be reached with synthetic fibers such as glass, carbon and aramid fibers. In recent years, however, the use of synthetic fibers is being questioned in terms of problems caused to the environment. In fact, as non degradable material, synthetic fibers are associated with long term pollution when discarded. Moreover, the expended energy for fabrication and processing can be related to relatively large amounts of C02 emissions and represents a contribution to global warming [3]. Glass fiber, in addition, is toxic and cannot be incinerated as a waste in thermal power plants [ 4]. Possible substitutes for glass fiber are the natural fibers. Many natural fibers are today being considered as viable alternatives to replace glass fiber as reinforcement of polymer composites. In particular, some natural lignocellulosic fiber extracted from plants present a real potential for this replacement [2-8]. Their comparative advantages are lower density and reduced cost as well as renewability, biodegradability, recyclability and neutrality with respect to C02 emission [3]."

Jan 1, 2011

By M. E. Huckman

In this paper, we review the equations needed to construct an ion exchange column model. These models contain three major components: 1) a differential material balance around the colunm, 2) a differential material balance around an ion exchange particle, and 3) a constitutive equation for diffusive flux We then examine the ability of a fairly simple mathematical model to predict ion exchange column experimental data. This model contains the traditional absorption theory equations and is used to predict the behavior of a column filled with a hydrous crystalline silico-titanate and which is removing trace amounts of Cs+ from a high pH, complex electrolyte solution. Finally, we propose replacing Fick's law with the Nernst-Planck equation as the constitutive equation for diffusive flux We use a Nernst-Planck type model to predict batch experimental data, then evaluate it by comparing it's ability to predict experimental data to that of a more traditional Fick's law type model? The data from this comparison suggests that the Nemst-Planck type model yields better results.

Jan 1, 1996

By Peng Peng, Ouo Cheng, Guodong Lai, Lijuan Chu, Zebiao Zhang

"The pressure acid leaching residue of zinc concentrate contains a large quantity of sulfur. The present study attempts to leach sulfur using a mixture of ammonium sulfide and water solution at 25°C. Effects of three leaching variables: ammonium sulfide concentration, leaching time, liquid/solid ratio on the sulfur leaching rate were investigated. The process conditions were optimized using response surface methodology based on the central composite design. From the analysis of variance (ANOVA), the significant factors on response were identified. The optimum conditions for leaching elemental sulfur from pressure acid leaching residue of zinc concentrate were obtained using an ammonium sulfide concentration of 2.5 mol/L, leaching liquid-solid ratio of 6.5:1 and leaching time of 7 min. Under the optimum experimental conditions, a maximum of 98.50% of total sulfur was extracted. The experimental results obtained agreed satisfactorily with the model predictions, with a correlation coefficient (R2) of 0.99.IntroductionSulfur is widely used in agriculture, medicine, rubber, building materials, gunpowder, wine and sugar, and other fields [1]. Currently the world sulfur production is 40Mt, out of which more than 90% is recovered from industrial processes, and 10% is natural [2], This highlights the importance of sulfur recovery. As the pressure leaching technologies [3] continue to mature and are increasingly applied to refining, a large quantity of high-sulfur residue is produced [4-5]. It is desirable to recover sulfur from this residue, so that it is economically advantageous, and reduces environmental pollution [6]."

Jan 1, 2012

By Y. Fukunaka, M. Niinae, E. Kusaka, T. Kuzuya, R. Ishii

"Samarium oxalattr particles was precipitated in oxalic acid aqueous solution from samarium-loaded D2EHPA solution emulsified with a conventional impeller. The calculated fractional precipitation of samarium oxalate was reasonably compared with the value determined by chemical analysis. Morphological variation of oxalate precipitate particles was then examined with H2C2O4 concentration in aqueous solution, Sm(III) and D2EHPA concentrations in organic phase. The needle-like precipitate was identified as Sm2(C2O4)3 10H2O by XRD. Precipitates obtained at higher H2C2O4· or Sm(III) concentration greatly decreased the length of major axis of precipitate, while those at higher D2EHPA concentration increased it. The oxalate was further precipitated under ultrasonic irradiation. However, the morphological variation caused by theses processing variables was not so evident under ultrasonic irradiation as in an impeller or shaking mixer.IntroductionThe materials processing of the rare earth elements must be reviewed from the scope of industrial ecology, since they have the potential applications of magnetic materials as well as secondary battery in developing programs of the electric vehicle. The technological trend to develop the electric vehicle may greatly influence the concept of materials processing, since the global· environmental problem must accommodate with the sustainable development for mankind. The recycle design must be a key issue in the materials science and engineering.Solvent extraction provides a unique separation technology -in this sense. Doyle (1)(2) reported the integrating solvent extraction with processing of advanced ceramic materials, whose chemical composition and microstructure must be precisely controlled. In her paper, the higher productivity inherent to the present process superior to hydrolyzing metal alkoxides was emphasized. Oxalic acid has been used as precipitant for rare earth purification process, since rare earth oxalate has a very small solubility in water and can be easily decomposed to oxide. It is thus suitable for precipitation stripping agent in cationic exchange type extracting system (i.e. D2EHPA, VA-10, PC-88A and so on)."

Jan 1, 2000

By Jeffrey R. Taylor

The distribution of low concentrations of Cr, Mn, Rh, Co, Ni, Ag and Fe between copper matte and bullion phases has been measured at 1200oC. These results. together with values for nine other elements, have been used to develop a simple model to describe the distributions in terms of known thermodynamic properties?. The Temkin model for ionic melts was assumed to apply to the sulphide species in the Cu-S matte? phase and it is shown that the choice of sulphide species is particularly important for successful representation of the experimental .results?. In general, the lowest sulphlde (minimum sulphur :. metal ratio)? formed by the. metal is most suitable, although Ni, Co, Rh and Pd appear to associate with more sulphur in the melt than suggested by the? composition of their lowest sulphide. A correlation between the composition of the metal sulphide species formed in the ternary system and the? position of the minimum in the free energy of mixing curve in the metal-sulphur binary -system is? proposed.

Jan 1, 1983

By Pengfu Tan

A thermodynamic model has been developed to predict the distribution behaviors of Cu, Fe, S, O, Pb, Zn, As, and heat balance in a lead blast furnace. The modeling results have been validated by the plant data of a lead smelter in Asia. The model can be used to predict for any set of controllable process parameters such as feed composition, smelting temperature, degree of oxygen enrichment and volume of oxygen-enriched air. The effects of the blast air, industrial oxygen, and coke charge on the distributions of Cu, Fe, S, O, Pb, Zn, As, and heat balance, and on the lead loss in slag have been presented and discussed.

Jan 1, 2005

By R. Colás, A. Salas, M. P. Guerrero Mata, R. Garza

"The use of the finite element method (FEM) for studying the plastic behavior of metals has become a common practice over the past few years, because it has been proved to be a good means of evaluating processes parameters, and predicting and improving processes, avoiding the traditional trail and error technique. FEM was used via a commercial package (Abaqus) to create two dimensional models to simulate uniaxial tensile tests for a galvanized low carbon steel. The aim of the work was to analyse the plastic behaviour of a distribution of grains on the zinc cover of a set of galvanized low carbon steel samples. A mesh with lines 2 mm apart was drawn on one of the faces of the samples that were deformed at room temperature, at constant crosshead speed, stopping the deformation at different times. Before and during the stops the deformation measurements were recorded for further calculations in an image analyser in order to compare these with computational predictions, as well as validate the numerical model. The results of this study can be extended to other testing conditions, besides the model can be used for obtaining constitutive equations of the materials.INTRODUCTIONThe use of the finite element method has been widely spread during the last two decades in most engineering areas, it is a good means of obtaining approach values at a first try [1-4]. Thanks to the software and hardware developments it is now possible to run huge problems within hours or minutes, making the technique more accessible and useful for the industry.The aim of this work is to create a finite element model for the uniaxial simple tension test, and compare the results with some experimental results, and asses the validity of the model.The plastic behaviour of the materials with FEM has been studied for a long time [5] and there is always something new to learn about this behaviour of the metals in particular, as well as to characterized new materials and alloys [6,7]. The tension test has been used since XIX century to get knowledge of the materials [5,8], it is the test that has been used the most and the only that is fully standardized, although it has the limiting of low strains, it is still the most widely used, especially in the industry.Two different finite element models in two dimensions (2D) have been developed, one called the mesh model and the other one the grain model, attention was focused on the geometry and strain prediction. The model is validated with experimental test, by using the data and directly comparing it with the numerical predictions. All the tests were carried out at the same constant crosshead speed at room temperature. An analysis of the grid distortion using FEM and analytical methods has been carried out."

Jan 1, 2001

By Pietro Navarra

A great deal of effort has been expended on how to optimize conventional water cooling circuits in furnace cooling elements, and the results have been largely satisfactory. However, there is a general agreement that the proximity of high-pressure water passages to the flow of molten furnace products is a safety concern. Nonetheless there exists little alternative to the formula: increasing furnace integrity implies the incorporation of more extensive forced-convection water cooling systems. Recent developments in evaporative cooling technology have resulted in the development of a high-capacity heat pipe capable of operating under the thermally intense environments of a metallurgical furnace. The system functions using several kg of a working fluid (water) in total, has no moving parts, and allows for a significant reduction in cooling water requirements. Full-scale pilot tests of a copper tap hole and slag launder were done in 2003 and2005, with detailed results given in this paper.

Jan 1, 2006

By W. M. Cross

Bubble attachment time measurements for the rare-earth phosphate minerals monazite and xenotime were made as a function of oleate concentration, sodium fluoride addition, and temperature. Results indicate that the rare-earth phosphates behave similarly to other phosphate minerals, notably collophanlte and fluorapatite, which have been studied previously. The addition of sodium fluoride yielded a modest decrease in bubble attachment time with fluoride additions below the apparent fluoride surface precipitation point, while at fluoride additions greater than the apparent precipitation point a significant decrease in attachment time occurs. Increasing the temperature or the system gave a slight decrease in bubble attachment time in the absence or sodium fluoride. With sodium fluoride addition and below the apparent fluoride surface precipitation point, an increase in temperature actually increased the attachment time. For sodium fluoride additions above the apparent fluoride surface precipitation point, a temperature increase significantly decreased the attachment time.

Jan 1, 1989

By Paul W. Cleary

Keywords: Reactive pellets, CFD, Lagrangian SPH, Pyrometallurgy In several pyrometallurgical processes, reactive pellets are added to a melt. Heat is transferred to the pellets and reaction products such as gases, metal and slag are formed. For many pyrometallurgical processes traditional grid based CFD methods, such as using the Finite Element Method (FEM) and Finite Volume (or Control Volume methods), produce suitable predictions. However, the inclusion of solids in the bath represents significant challenges for these methods. Smoothed Particle Hydrodynamics (SPH), a Lagrangian simulation method, is able to simulate both the fluid component of the bath and any immersed solid materials, tracking the motion of these solids, and their interaction with the fluid, including gas generation. In this paper, we will summarize the key aspects of the SPH method and will show a series of structured examples illustrating the behavior of the different physics sub-systems that are used in the model of the overall system.

Jan 1, 2005

By Ray Y. Lin

This study explores the formation of sodium pyrosulfate in molten sodium sulfate resulting from dissolution of SO3 at temperatures between 1160 and 1250 K. Solubility of SO3 in Na2SO4 melts at temperatures between 1160 and 1250 K under gas mixtures of SO2, O2 and argon was investigated applying a thermogravemetric analysis (TGA) technique. The activity of Na2O in the melt was determined with a high temperature electrochemical cell (ECC). Results showed that the SO3 solubility in molten Na2SO4 increases with decreasing temperatures and increasing SO3 partial pressures. Enthalpy of SO3 dissolution in molten Na2SO4 was calculated to be -119 kJ/mol for infinite dilute solutions. Thermochemistry of Na2SO4-Na2S2O7 melts was analyzed based on information obtained from both TGA and ECC techniques. Detailed examinations of the earlier low temperature measurements in the Na2SO4-Na2S2O7 system along with data from this study reveal that the solution behavior between Na2SO4 and Na2S2O7 can be satisfactorily treated as regular with the interaction parameter, , being 2.7 kJ/mol. The phase diagram and the field of SO3 partial pressure has been generated with the thermodynamic calculation using a regular solution approach.

Jan 1, 2006

By Guolin Zheng, Tiejun Chun, Jian Pan, Deqing Zhu, Xianlin Zhou, Dong Chen

"The high temperature oxidizing-chloridizing roasting is one of useful methods to separate nonferrous metals from pyrite cinder and metallurgy slag. However, as one kind of main nonferrous metals in pyrite cinder and metallurgy slag, copper’s chlorination behavior is not demonstrated. In the present study, chlorination behaviors of CuO, Cu2O and CuS at the temperature range of 1025-1175 ? in air by simulating the chloridizing roasting process of pyrite cinder and metallurgy slag have been investigated. It is shown that Cu2O and CuS is much easier to remove, CuO is refractory to remove. In addition, the presence of SiO2 and CaO increases the Cu removal rate from CuO while the presence of SiO2, Al2O3, CaO and MgO decreases the Cu removal rate from Cu2O. Fe3O4 influences the Cu removal rate from CuO and Cu2O positively.IntroductionAs two kinds of significant secondary resources, pyrite cinder and metallurgy slag contain not only abundant iron but also considerable copper, lead, zinc etc. Millions of tons of pyrite cinder and metallurgy slag were discharged from nonferrous metal and chemical industries annually [1, 2] in China. The pyrite cinder and metallurgy slag are formed by roasting of minerals at a high temperature, so the properties of them are distinctly different from the natural iron ores, and the iron in them is closely associated with copper, lead, zinc and other nonferrous metals. High-quality pyrite cinder and metallurgy slag containing high iron and low impurities can hardly be obtained, leading to their low utilization degree [3]. Chlorination is characterized by the high reactivity of chloridion, the high volatility and low melting point of metal chlorides, and the big differences in the formation of metal chloride. Therefore, chlorination is widely applied in extraction metallurgy."

Jan 1, 2012

By Guo Xueyi

The dissolution behaviors of valuable metals, lead and zinc, from secondary fly ash generated in municipal incineration plants were investigated using some lixiviants: sulfuric and hydrochloric acids, acetic acid and some chelating reagents including L-asparaginic-N,N-diacetic acid (ASDA), a biodegradable, and therefore, environmentally benign novel chelating reagent. It was found that zinc exists mainly as ZnO, whereas Pb probably as PbOHCI and PbO, and the easily soluble components in SFA are KCI and NaCl. Suitable amount of HCI can dissolve all of lead and zinc from SFA. Sulfuric acid can selectively extract zinc leaving lead in the residue. Ethylenediaminetetraacetic acid (EDTA) is an effective chelating reagent to extract both zinc and lead. Although ASDA and diethylene¬triaminepentaacetic acid (DTPA) can selectively extract more than half of lead from SFA, it would by no means be regarded as highly effective reagents for the extraction of these metal values. Keywords: Lead, Zinc, Secondary fly ash, Leaching, Dissolution

Jan 1, 2002

By Guo Xueyi

The method of Substance Flow Analysis (abbreviated as SFA) provides a helpful tool for the study of the industrial metabolism of a certain metal within a regional level. In this work the flow of lead in China, 2006, was traced within the STAF model, and the situation of production, consumption and recycling of lead resources in China were introduced. The SFA is performed on lead flows during its one year life cycle in detail. As one of the biggest producer and consumer of lead in the world, China is facing a problem depletion of lead resources. How to increase the resource efficiency is a significant issue for lead industry of China. Based on the result, several suggestions were proposed in the paper, aiming to contribute important reference information for the industrial metabolism and resource management and recycling of lead industry in China.

Jan 1, 2009

By David Norval

Water solidification of mattes, metals, alloys and certain slags with high metal entrainment has customarily not been practiced due to the belief that such processes are too dangerous and unproven in the Pyrometallurgical Industry. Slag granulation on the other hand is extensively applied, although in some cases crudely, with disastrous effects, as a result of not recognising the high heat capacities prevalent in slags. This paper will examine the most common air solidification processes and compare such processes with water solidification, mainly slag and matte granulation processes and design criteria for safe and reliable operation. Finally, purpose designed granulation and solidification processes will be discussed taking into account specific applications and the individual signatures of alloys and slags, emphasising that no slag, matte or alloy responds in similar fashion to a granulation practice.

Jan 1, 2006

By A. V. Tarasov, S. D. Klushin

493 The most common method for minimizing the copper content of residual slag in the process of autogenous smelting of sulfide raw materials is treatment of molten slag in an electric furnace, with optional addition of solid reducing agents, such as coke, and/or sulfiding agents such as pyrite. A drawback of this technique is the fact that the final slag produced still contains 0.5% or more Cu. We have tested a method for treating molten slag obtained as a result of autogenous smelting by a gaseous mixture of sulfur dioxide and methane at a ratio of. SC:SO2 = 0.75 :1.0 in the presence of oxygen. Interaction reaction within the SO2-O2-CRi system proceeded at a high rate at 1373 to 1573 K to form reducing and sulfiding agents: H2S, S, COS, CO, CO2, H2, H2O. The gas mixture requirement was about 100 to 150 Nm3 per 1 tonne of slag. A decrease in the ferric iron concentration (Fe3+) from 10-15% down to 2-3% resulted in lower solubility of copper in slag, and agitation of the melt with gas stream accelerated. the separation of the sulfide phase and slag. Removal of copper from slag was performed in a pilot unit within the second V anyukov furnace zone where slag arrived with a copper content of 0.8-1.3%. The temperature of molten slag was maintained within 1523 to 1573 K. The copper content of the final slag was at a level of0.12 to 0.14%. The matte sent to converting was a mixture of bottom matte from the smelting zone and the slag treatment zone. It had a copper content of about 50 to 55%. Process gases from both furnace zones were combined and sent to the acid plant for sulfur recovery. This process was offered for commercial use at two copper smelters in Russia and CIS.

Jan 1, 2000

By Kazuyuki Kakegawa

The sintering characteristics and the change in the compositional distribution in the PbTiO3-PbZrO3-Pb(Mg1/3Nb2/3)O3) system during the sintering process by spark plasma sintering (SPS) method were examined. They were compared with those by a normal sintering method. The densifieation by the normal sintering was slow even at high temperatures. When SPS method was employed, much lower temperature and shorter period resulted in sintered bodies having almost the theoretical density. As expected in normal sintering, the compositional distribution decreased as the sintered density increased. On the contrary, the change in the compositional distribution by SPS was much smaller than that in the normal sintering. This sintering characteristic of SPS suggested a possibility of fabrication of sintered material having a desired compositional distribution.

Jan 1, 2003

By Yanhui Liu, Xuewei Lv, Chenguang Bai

A thermodynamic model for determining the surface tension of molten slag by considering the surface tension and molar volume of the pure oxide component, and their ionic radii was extended to the slag bearing high TiO2 (varying from 80 to 67%) at 1973 K. The iso-surface tension curves for the FeO-TiO2-Ti2O3 ternary system at 1973 K are almost parallel to the FeOTi2O3 line. TiO2 plays a role of surface-active solute, and its surface-active effect is attenuating with increasing the TiO2 content. The iso-surface tension curve shifts away from the TiO2 corner, indicating that the surface tension of the ternary slag decreases along with the addition of SiO2. The reasons include the addition of SiO2 with lower surface tension and the decrease of the total ion moment at the surface. Both CaO and MgO can bring about that the iso-surface tension curve shifts towards the TiO2 corner, indicating that the surface tension of the ternary slag increases along with the addition of CaO or MgO. CaO has a more pronounced effect on increasing the surface tension of the ternary slag than MgO at an equimolar amount addition. The increase of the surface tension results from both the compositional change and the variation of the slag structure.

Jan 1, 2015

By M. O. Lai

"Metal matrix composite (MMC) with composition of Al-4.Swt.%Cu reinforced by IOwt.%TiB2 or ISwt.%SiC particulate has been successfully fabricated using powder metallurgy technique. Disk, compression and beam specimens were prepared with (a) layered structure containing ductile Al-4.Swt.%Cu with brittle Al-4.Swt.%Cu/TiB2 or Al-4.Swt.%Cu/SiC layers, and (b) homogenous constituent with composition of Al-4.Swt.%Cu/lOwt.%TiB2' The specimens for the fracture toughness measurement were built through three ductile-brittle-ductile alternating layers. For the beam specimens, the layers were built through brittle-ductile-brittle sequence. The brittle layer consisted of Al-4.S%Cu with fixed amount of reinforcement. Fracture toughness testing revealed an increase for layered composites although the total amount of the reinforcement was the same for all disk specimens. The increase in fracture toughness is due to the existence of ductile layers which manifests a strong influence on delaying the occurrence of fracture. It acts as a barrier to resist the propagation of crack and hence increases the fracture toughness of the layered MMC specimens, Delamination in the beam specimens was observed to be due to shear stresses. Fracture surfaces of both disk, compress and beam specimens were characterized using the SEM. IntroductionMechanical and thermal properties can be achieved by the incorporation of refractory secondary phases to constrain the plastic flow of the matrix in a metal matrix composite (MMC). The size of the reinforcement particulate incorporated must be in the range larger than the dislocation cell size and strongly bonded to the matrix (I). Particulate reinforced metal matrix composites hence provide high modulus, improved wear resistance and strength (2-4). Because of the incorporation of refractory phases which are generally brittle, the major limitation in the mechanical properties of MMCs is their limited ductility in comparison to their base metals. Cracks normally initiate from the reinforcement and voids (4, 5). Due to the lack of ductility, cracks propagate rapidly with increase in load. As a result, the interactions between reinforcement particles and propagating cracks have recently been of great research interest (6). In addition, volume fraction of reinforcement and aging condition of the matrix significantly affect the mechanical behaviour of MMCs. In the case of AI-3.5%Cu reinforced with varying volume fractions of SiC particulate, it has been found that the probability of particle fracture increased with increasing volume fraction of reinforcement (7)."

Jan 1, 1996

By Paul O. Malan

"The Tusc gold deposit is located along the Carlin Trend approximately 13 kilometers north of Carlin, Nevada and 2.5 kilometers northwest of the Gold Quarry mine. Tusc is one of several structurally controlled oxide gold deposits located along the Good Hope fault within the Maggie Creek subdistrict. Mining commenced in 1994 with an oxide reserve of780,000 troy ounces of gold at an average grade of 1.34 g/t Au. The Good Hope fault forms the southwestern edge of the Schroeder Mountain uplift (also known as the Carlin Window) and juxtaposes carbonate rocks of the Siluro-Devonian Roberts Mountains Formation against siliceous mudstone, siltstone, and silty limestone of the Devonian Rodeo Creek unit. Submicroscopic gold mineralization is disseminated in the Good Hope fault system and in fractured hanging wall carbonate rocks. Wallrock alteration includes silicification, deca!cification, sericitization, and late alunite replacement and veins. All Tusc ore is transported 2.5 kilometers to Gold Quarry for processing. Leach-grade ore (0.2 - 1.7 g/t gold) is placed on the oxide leach pads, and mill-grade ore(> 1.7 g/t gold) is processed through the CIL oxide mill. IntroductionThe Tusc gold deposit is located in Eureka County, Nevada, U.S. A, approximately 13 kilometers north of the town of Carlin and 2.5 kilometers northwest of the Gold Quarry mine (Fig. 1 ). Tusc is one of several open-pit, oxide, gold deposits within the Maggie Creek subdistrict of the Carlin Trend. Tusc is a structurally controlled gold deposit located along the Good Hope fault. Submicroscopic gold mineralization is disseminated in the brecciated and silicified Good Hope fault zone and along intersecting northeast and northwest striking structures."

Jan 1, 1997