Search Documents

By J. B. STEWART

T HE position of each hole of any series of holes was carefully located by the surveyor, plotted in plan and elevation, and numbers assigned to them. The second series was staggered halfway between the first and so on for each succeeding series. Two and a, half to three months was frequently required to grout a series of holes calculated to insure safety for sinking a distance of 10 meters or say 33 ft. Naturally the initial operation called for drilling and grouting two series of holes but thereafter each sinking campaign required only one series of holes as shown in Fig. 8. The pump handling about 75 gal. per minute corresponds to 46 tons of grout or 6 tons cement delivered as a fair over-all average for the 24 hours. Thus 600 to 800 tons of cement was used for a single section of 33 ft. depth of shaft. One campaign used nearly 1100 tons of cement. Some holes were effectually sealed with as low as 30 tons, while many required 60, and some 80 to 90 tons.

Jan 1, 1926

By P. C. Thakur

In Part I of this paper, it was established that the width of longwall faces in highly gassy mines is primarily limited by the volume of air reaching the tail-end of the face. The ventilation air reaching the tail-end of the face should be not only enough to keep methane concentrations below the statutory limits (generally 1 percent) but also enough to prevent any gas layering. The air volume leaking from the longwall face into the gob should also be able to push the explosive methane-air mixture away from the gob area immediately behind the longwall face where active roof-fall is taking place (typically 30-45 m). The second group of variables that also controls the width of the longwall panel consists of (a) the rate of advance, (b) bleeder air quantities, (c) specific methane emissions for the gob area and, (d) efficiency and cost of gob gas capture. This paper will discuss the second group of variables and its impact on the optimum width of longwall faces in highly gassy coal mines.

Jan 1, 2009

A self-appointed, committee consisting of J. Waldo Smith, Chairman, Richard S. Buck, J. J. Carty, J. Parke Channing, E. L. Corthell, Alfred Craven, Thomas Crimmins, Gano Dunn, George Gibbs, Alex. C. Humphreys, F. L. Hutchinson, Charles Warren Hunt, D. S. Jacobus, John W. Lieb, William Barclay Parsons, George H. Pegram, Charles F. Rand, Calvin W. Rice, Robert Ridgway, William L. Saunders, Merritt H. Smith, Bradley Stoughton, and William H. Wiley, organized a course of seven free lectures on military engineering, which were given by Captains Thomas M. Robins, Richard T. Coiner, Edward D. Ardery, Corps of Engineers, United States Army, and which was under direction of Major General Leonard Wood. The United Engineering Society presented, without charge, the use of the auditorium for the purpose of these lectures, but the interest proved to be more than three times as much as had been expected, and it was therefore necessary to divide the courses into three parts, one of which was given in the afternoon in the auditorium of the United Engineering Societies Building, one in the evening in the same place, and another in the evening in the auditorium of, the American Society of Civil Engineers. These lectures occurred on Mondays, from Feb. 14 to Mar. 27, 1916. The subjects and speakers were as follows: Feb. 14, 1916: Organization and Duties of Engineers in War, and what Engineers in Civil Life will be called upon to do in the Defence Of the United States. Captain Thomas M. Robins, Corps of Engineers. Feb. 21, 1916: The Service of Reconnaissance Including Surveying, Mapping and Sketching, Photography and Map Reproduction. Captain Richard T. Coiner.

Jan 5, 1916

The Black Hills Mineral Atlas briefly summarizes all important data available on the mines and mineral deposits in the Black Hills that have been explored, developed, mined, or located. The purpose of the atlas is threefold; First, from available data the general potentialities of the Black Hills region can be determined, although it is not possible to calculate actual ore reserves; second, it will provide the necessary basic information regarding a given property or commodity for further detailed study; and third, the compilation is a comprehensive directory of Black Hills deposits.

Jan 1, 1955

By Peter Fischer

Reducing mining costs has become such an important factor in the German coal industry that operators are forced to work only those areas where production costs can be kept low. These areas will normally be located close to the mine shafts because they are easily accessible. Even the shaft pillar is now being considered as part of the winning zone. Before working coal in shaft pillar zones it is essential to assess the impact this will have on the shaft lining. There is a huge difference between sliding and strata-anchored shaft systems. However, if the overburden comprises lightweight soil both types of shaft will have a tendency to protrude from the surrounding ground. This paper presents the geomechanical reasons underlying this reaction and the methods used for predicting and measuring it.

Jan 1, 2007

By C. K. Kocsis

A study was undertaken to evaluate the thermal environment and determine the contributing heat sources within the existing 153 Orebody of Coleman/McCreedy East Mine which would then enable the prediction of the climatic conditions in the mine?s future 170 Orebody. The study entailed continuously monitoring, for a 2-week period, the dry-bulb temperature, humidity and barometric pressure along the existing intake airways from surface down to the 4810 Level and throughout an active mining area on that level. Furthermore, the mining activities and associated equipment that could be responsible for any changes in the temperature and humidity conditions within this mining area were also monitored. These data were then used to develop and validate a climatic simulation of the mine?s mechanized cut and fill mining method. This climatic model was then transposed to the future 5700 Level in the deeper 170 Orebody, to determine the environmental conditions within its production workings and along the main haulage route ascending from that area. Based upon the simulations performed it was shown that the level of ventilation planned for the new orebody should be able to maintain adequate environmental conditions. However, this study did emphasize the importance of the appropriate distribution of airflow in workplaces that used auxiliary ventilation in order to sustain a suitable thermal environment.

Jan 1, 2009

"INTRODUCTIONThe Kidd Creek Concentrator is located 28 kilometers east of the city of Timmins, Ontario. Two types of ore are treated; 'A' type, a copper-zinc-low silver ore producing copper and zinc concentrates, and 'C' type, a copper-lead-zinc-high silver ore producing copper, lead and zinc concentrates.The ore is processed at a combined rate of 12,400 metric tonnes per day through four parallel grinding and flotation divisions. Three divisions treat the 'A' type ore and the fourth treats the 'C' ore. Each division is fed from its own fine ore bin.This paper reviews the grinding section with specific emphasis on grinding media consumption and the factors affecting it as related to 'A' type ore. At Kidd Creek there was an awareness that grinding media consumption varied on a weekly and monthly basis. The reasons for this variation was usually attributed to ore hardness as evidenced by short term variations in the circuit feedrate and head assays. However, there has been a diversity of opinion published in recent years regarding the factors contributing to steel consumption. This initiated a study of historical Kidd Creek operating data, from the period 1970 to 1986 inclusive, to determine the effect of various operating parameters on media consumption. The results of the study could then be used as a baseline for future media consumption testwork."

Jan 1, 1988

By M. Newton

Optimization and sensitivity analysis of mineable economic volumes have been standard practise for open pits for many years now, and more recently software has become available to apply techniques for delineating mineable reserves for underground mines. In general these techniques have been applied to a single resource model to quantify mineable tonnes and grade for underground mining. However by using multiple conditionally simulated models both the risk associated with the mining parameters and the risk associated with variations in grade, tonnes and profit can be quantified. Using suitable software the mine planner can then easily and quickly define and compare alternative designs to assess and improve the robustness of and the confidence in the final design.

Jan 1, 2007

By Ian Townsend

A prerequisite for good filter performance is that the total filter installation has been well designed. In this sense, the filtration testwork will provide scale-up data, and an insight into the relationship between operating parameters that may then be optimised, and used in the development of a control strategy. A good understanding of the filter’s operating principles will ensure correct selection and sizing of ancillaries, allowing in particular for the difference between instantaneous and average flow rates.

Sep 13, 2001

By Harry R. Johnson

Domestic expenditures by the U.S. petroleum industry have exhibited distinctive shifts in emphasis over the past 20 years. From the end of World War II to 1955, expenditures for all phases of the industry expanded. Although over one-half of all expenditures were for production, the relative emphasis was changed after 1956-58 from production toward processing and marketing. The period 1967-69 marked the beginning of a return to emphasis on exploration and production. These trends in expenditure patterns are logical and rational when related to domestic and international economic conditions and to the widespread application of improved production technology. As the immense job of developing the oil resources of Alaska and other regions begins, the petroleum industry will continue to turn to external sources for working capital. Long-term debt will probably be the principal method of external financing through 1970, but a definite shift toward new common and preferred stocks will be made. Higher product prices may be sought by the petroleum industry, but the economics of crude-oil production, changes in the tax structure, and possible changes in the oil imports control program make the price structure of crude oil and crude-oil products unpredictable at the present time.

Jan 1, 1970

The residues produced during the incineration of leather scraps contain significant amount of chromium which can be recovered and reused in the tanning industry. The objective of this study is to develop a cost effective method for chromium recovery from leather ashes produced during the incineration of leather scraps using a fluidized bed incinerator. The entire process investigated involves fusion of leather ash with sodium carbonate in air to oxidise chromium to sodium chromate, leaching with distilled water to dissolve chromates, and chromium reduction from the hexavalent to trivalent state by sodium thiosulphate solution. The main factors affecting chromium extraction, such as temperature, reaction time, and sodium carbonate to leather ash ratio, were investigated. Based on the results obtained, almost 100% Cr extraction can be obtained at 700°C fusion temperature, sodium carbonate to ash weight ratio equal to 3 and retention time longer than 50 min.

Jan 1, 2006

By Claude H. P. Lupis, John F. Elliott

QUITE generally an increase in the temperature tends to bring a system closer to ideality. It is reasonable as a first approximation to consider that the excess free energy will vary linearly with the temperature, or: where t may be defined as the "characteristic temperature" of the solution, or the temperature at which the system would become ideal if the results at T were linearly extrapolated. It must be emphasized that consideration of this hypothetical property is an appeal to intuition rather than an established physical concept. The order of magnitude of 7 for dilute solutions will depend on the nature of the solvent; a value of 3000° + 1000°K may be suggested for ordinary metallic solutions. In terms of free energy, entropy, and enthalpy first-order interaction coefficients, differentiation of the above equations with respect to composition leads to The concept of t offers a simple and plausible interpretation of Chipman and corrigan's3 recent empirical correlation between and a for a number of groups of ternary systems 1-24. The authors found that in each group the ratio was approximately constant. The corresponding calculated from their data by Eq. [4] are listed in Table I. The expected order of magnitude is obtained for 7. As noted by Darken,4 if a regular solution is not assumed, thus if utj) # 0, Chipman and Crrigan's results imply that, as T is increased, ultimately changes in sign, Fig. 1. Clearly Eq. [4] is valid only in a limited range of temperatures since at the temperature 7 at which the system becomes ideal not only should become null but also and . Thus, both and are functions of

Jan 1, 1967

By J. L. Perry

FOR many years, you and your fellow members of the American Institute of Mining and Metallurgical Engineers have devotedly and ably applied yourselves to the art of making iron and steel. having foremost in your minds the conservation of raw materials, suitable and efficient facilities, economical processes, and improved quality of product. For the past three strenuous years you have contributed wholeheartedly to meeting the problems of increased production. You have conducted scientific and technical investigations and research, recommended experiments. and gathered all the available and valuable information possible to gain the desired objectives. You have had many obstacles and difficulties to overcome. In the early days of your organization, there was some lack of co-operation from the industry itself-perhaps, for example, some failure to recognize the mutual advantages of free exchange of experiences and information. But regardless of any hindrances, you have made many and valuable contribution which have tended to make iron and steel manufacture leas of an art and more of a science.

Jan 1, 1944

By F. R. Wadleigh

There are in commercial use today in the United States various classifications of coal, each based on one or more characteristics. The bases of these classifications may be described as follows: GeNeRaL Basis Examples 1. Geological By seams and basins (local). 2. Chemical By constituents, as determined by analysis—ash, volatilc, slilfur and hcating value. 3. Combustion Characteristics As frce-burning, smokeless, character of ash. 4. Carbonization Characteristics Coking, noncoking. 5. Physical Characteristics Splint, soft, hard, block. 6. Geographical States, Fields, Counties, Districts. 7. Sizes By dimension or name. 8. Company Names Producing or sales company names, as "C. C. B. Pocahontas," etc. 9. Trade Names, copyrighted or not 10. Uses Gas, steam, coking, locomotive, fuel, bunkers, etc. 11. Use Methods Stoker coal. 12. Pools (Tidewater Exchanges) Analyses Size Seams Railroads Uses Structure Districts There are also classifications founded on more than one basis, as follows: 1. Geographical and Geological. By locality of mines (State, District, County) and seam. Examples: Cambria County, Miller Seam, New River, Sewell Seam. 2. Geographical and Chemical. Alabama medium volatile. 3. Combustion Characteristics and Ash Content. Free-burning, red ash (anthra- cite). 4. Carbonization Characteristics and Analysis. Noncoking, high-volatile, low sulfur. 5. Physical and Carbonization Characteristics. Splint, noncoking. 6. Size and Use. ¾-in. gas coal; domestic sizes (prepared sizcs); stcam sizcs. 7. Company Name and Seam. Consolidation Co., Elkhorn. 8. Size and Analysis. Low-volatile run-of-mine; low-volatilc slack. 9. Sizes—size of screen and name. 6 by sin. lump. 10. Chemical and USP. High-volatile steam. 11. Geographical and Use. Youghiogheny gas. 12. District, Size and Use. Pittsburgh gas l¼-in. lump. ,

Jan 1, 1930

By C. M. Davidson, D. J. Drexler

"Sulphuric acid treated with hydrogen peroxide to destroy organic contaminants could conceivably show increased corrosivity toward carbon steel shipping and storage vessels, caused by the persistence of a peroxide residual. This paper describes work performed to determine the effect of 0-200ppm hydrogen peroxide on the corrosion of carbon steel by 93% and 98% sulphuric acid at room temperature (23ºC) and 50ºC.Steel electrodes were exposed to acid containing several peroxide levels (0. 45, iOO and 200 ppm) for up to two weeks. Specimens were removed at intervals and weight loss, open circuit potential, depth of metal loss and residual peroxide concentration recorded.Hydrogen peroxide decomposes considerably over two weeks in iron-contaminated sulphuric acid. initial peroxide concentrations > l00 ppm suppress corrosion, but the effect is lost when concentration decays below about 60 ppm. Sustained peroxide levels in the range below 60 ppm may increase corrosion rates. These phenomena are interpreted by analogy with anodic passivation."

Jan 1, 1987

By T R. Stacey

South Africa has a long history of rockbursts, some 100 years. During this time much research and many developments have taken place in the country to limit the occurrence of rockbursts, and to mitigate their effects. In this paper I shall present a personal view of what I consider to be important achievements, and contributions made. Some of these are: planning of stope layouts, and the use of strike barrier pillars; recognition of energy as a key factor, the use of the energy release rate ERR as a layout planning criterion, and development of MINSIM for calculation of ERR and stope planning; sequential grid stope layouts; use of backfill for stope support; and, development yielding support elements, and dynamic testing of stope and tunnel supports. The record shows the establishment of a rock engineering research powerhouse over a 40 to 50 year period and, unfortunately, the complete breakdown of this capability in the subsequent 10 years. CITATION:Stacey, T R, 2018. A personal review of South African rockburst research, experience and lessons learnt, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 5–16 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By S. Castro, L. Gutiérrez, L. Uribe

"Use of lime in seawater as a pyrite depressant decreases Mo recovery in flotation of Cu- Mo sulfide ores. When technology that uses sodium metabisulfite (MBS) to depress pyrite is applied, the process is carried out at pH 6.5–7.5, the range where Mo recovery is higher than the usual pH 11.0–12.0 when lime is applied. Redox conditions and chemical reactions involved in depression mechanisms of pyrite by MBS, or sodium sulfite, in seawater are investigated and discussed based on the acidifying effect of MBS, oxidation of sulfite ions by dissolved oxygen, and the role of catalyst of some metal cations (e.g., copper ions) adsorbed on pyrite’s surface.RÉSUMÉ L’utilisation de chaux dans de l’eau de mer comme agent déprimant de la pyrite réduit la récupération de molybdène (Mo) dans la flottation de minerais sulfurés de Cu-Mo. Lorsque l’on applique la technologie utilisant du métabisulfite (MBS) de sodium comme agent déprimant de la pyrite, le procédé se fait à un pH de 6,5 à 7,5, gamme dans laquelle la récupération de Mo est supérieure au procédé habituel utilisant un pH de 11,0 à 12,0 lorsque l’on applique de la chaux. Les conditions de réduction-oxydation (redox) et les réactions chimiques impliquées dans les mécanismes de dépression de la pyrite par le MBS (ou sulfite de sodium) dans de l’eau de mer sont étudiées et débattues sur la base de l’effet acidifiant du MBS, de l’oxydation des ions sulfites par de l’oxygène dissous et du rôle de catalyseur de certains cations métalliques (par exemple les ions de cuivre) adsorbés à la surface de la pyrite. INTRODUCTIONThe copper industry is aware of the difficulties of floating Cu-Mo sulfide ores in seawater. Molybdenum recovery is partially depressed when lime is used to reject pyrite. In plant practice, sodium metabisulfite (MBS) has been demonstrated to be the most promising option for replacing lime in seawater."

Jan 1, 2017

By John C. Sawyer

A brief review is given to show that catastrophic oxidation of stainless steel in the presence of lead oxide is similar in many respects to catastrophic oxidation as caused by MoO3 and V2O5, Experimental data are presented to show that lead oxide accelerates the normal oxidation process of stainless steel by chemically altering the normally protective oxide film formed on the base metal. Data are given to show that similar reactions occur during oxidation of stainless steel in the presence of MOO3,and V2O5. THE mechanism by which pure metals oxidize at high temperatures has been the subject of intensive research for many years and much has been accomplished towards understanding the processes involved. The mechanisms by which alloys oxidize have also been investigated, but due partly to the fewer number of investigations and partly to the complexity of the oxide systems present, available knowledge is not as extensive as with pure metals. When oxidation processes are further complicated by atmospheres contaminated with sulfide, halide, or oxide vapors, the knowledge of fundamentals becomes meager or altogether lacking. Thus, it is not surprising to find that the catastrophic oxidation of stainless steels in metal oxide vapors of MOO, and V2O5 is not a well understood phenomenon despite the fact that a number of investigations have been undertaken. The literature in dealing with the subject of catastrophic oxidation is primarily concerned with the effects of MOO3 and V2O5, but does mention that other metal oxide vapors, one of which is lead oxide, appear to promote a similar type of accelerated oxidation. While this latter effect is virtually unknown, the deleterious effect of lead oxide is of considerable commercial importance, as it is believed to be one of the fundamental reasons for exhaust-valve failure in gasoline engines. For this reason studies have been in progress for many years attempting to better understand the mechanism involved. Modern exhaust-valve alloys"2containing 20 to 25 pct Cr plus nickel and/or manganese are in effect high-grade austenitic stainless steels exhibiting ex- cellent oxidation resistance in air at exhaust valve operating temperatures of 1100° to 1700°F; yet these same alloys are prone to corrode during engine service because of the conditions attending their operation. These conditions are such that the valves become coated with deposits of complex lead compounds mainly derived from gasoline additives of tetraethyllead, ethylene dibromide, and ethylene dichloride. Literature searches3-7 and discussions with various investigators show that considerable difference of opinion exists as to the nature of the lead-bearing deposits found on the surface of exhaust valves and the atmospheres to which they are subjected; yet, all seem to generally agree that corrosion, a gradual transformation of alloy to nonmetallic products of corrosion, is a consequence of the presence of lead compounds. This majority opinion seems to be substantiated by laboratory engine tests which show that corrosion does not occur to any appreciable extent when lead-free fuels are used. The first observations of catastrophic oxidation reported in the literature were probably made by pfeil,8 but it was Leslie and Fontana9 who undertook the first detailed study of the phenomenon. Their work was chiefly centered on the acceleration of oxidation which took place when stainless steels containing more than 3 pct Mo were heated in air with restricted circulation. These investigators reported that the presence of other oxides near the surface would further accelerate the rapid oxidation which occurred. While they recognized that the effect was attributable to the presence of molybdenum, it was Rathenau and Meijering" who emphasized the fact that the presence of molybdenum in the alloy was incidental to the presence of MOO3 vapor in the atmosphere surrounding the specimens. Evans,11 as well as Cunningham and Brasunas 12 studied similar

Jan 1, 1962

By E. Topuz, C. Patrick

Longwall face-to-face transfers can cost more than $100 per minute in lost production potential and $100,000 for personnel and supplies. Such high costs make extensive planning and control of the transfer process a critical necessity for the economic feasibility of longwall operations. Operations research techniques are used for the analysis and modeling of longwall face-to-face transfers. Transfer data has been collected from companies who operate, over 35%, of the total US longwall faces. Comprehensive sequence networks of existing longwall transfers were developed; simulation was used to generate models of transfers under Carving conditions; and the economic feasibility of tine-cost tradeoffs in the transfer procedure was investigated.

Jan 1, 1994

By Alain Blouin, Mohamad Sabsabi, Aissa Harhira, Paul Bouchard, Greg Lithgow

"The objective of this study was to demonstrate the application of Laser-Induced Breakdown Spectroscopy (LIBS) to the continuous analysis of online monitoring of Al, Mg, Ni, Mn, Si and Fe in nickel ore limonite and saprolite slurry samples. Analysis was performed on slurry samples in air at atmospheric pressure. Two pure samples of limonite and saprolite were used. Mixtures of the two samples in varying proportions were used to build calibration curves, study the influence of solid/liquid ratio, and evaluate short and long term reproducibility. The LIBS measurement of these elements is independent of the water content (from 70-85%, the range allowed by our setup). Repeatability of the measurement and long term reproducibility (from day-to-day) were below 1.2 % and 2% respectively for all the elements studied in our conditions. The results obtained showed that an industrial LIBS analyzer could provide the chemical composition of the six elements Al, Mg, Ni, Mn, Si and Fe within 1-2 minutes.IntroductionThe metal-producing industry faces the major challenge of increasing productivity, reducing costs, and maximizing benefits from existing equipment. By pyrometallurgy, metal making involves the basic steps of charging the furnace, melting the charge and refining. By hydrometallurgy, the metal refining is carried out through the dissolution of the metal by chemical reaction and electrolysis. During refining either by pyrometallurgy or hydrometallurgy, it is critical that operating parameters be adjusted and controlled so that the chemistry of the melt or the solution is within predetermined limits. Presently, the complete turnaround time for sampling, sample transfer, analysis and communication of the results to the operators is often 30 minutes or more."

Jan 1, 2016