Search Documents

By Kenneth M. Bravinder, Jonathan E. Koogle, Dean H. Sheldon

THE solution of subsurface geological problems requires an analysis of vertical and horizontal dimensional relationships. For many, the ability to visualize structures in three dimensions is not easily acquired, and for areas where the structural conditions are complicated by faulting the need arises for illustrative models. This has led to the many forms of peg models, in which the usual course of construction includes a peg for the well bore, and the suspension of strings from peg to peg to illustrate the formation correlation between wells, thus developing the usual folds and flexures. Such models proved unsatisfactory for the analysis of fault problems. Consideration was then given to the use of transparent materials. A model of the Dominguez oil field was constructed in 1935, which consisted of a series of glass panels from well to well on which the formations were shown in color. This model, though serving its purpose at the time, proved to be impractical from the standpoints of cost, breakage hazard, and extreme difficulty in maintenance. The cost of materials was estimated to be approximately $300, and the construction required the services of one man for a period of from 10 to 12 months. Maintenance after actual construction was an additional expense. Consideration was then given to the use of celluloid, and after some experimental work it was found that the advantages in its use were: (I) a short construction time, (2) ease of handling the material, (3) sections are easily reworked, (4) low cost. CONSTRUCTION It would be of little value to recount here the difficulties encountered in the building of the first celluloid model. The conclusions drawn, however, suggest the following procedure for those who contemplate the construction of such a model: I. Determination of the Scale.-Accurate geological interpretation requires the use of the same scale horizontally and vertically. It should be emphasized that the limited size of the celluloid sheets (20 by 48 in. maximum dimensions), the area to be studied, the maximum depths to be plotted, and area of possible future development are the controlling factors in adopting a scale to be used. 2. Construction of the Base.-A satisfactory base may be constructed by using two pieces of three-ply wood separated by strips of i by 2-in. material. This type of construction prevents warping of the base. The size of the base is determined by the dimensions of the area to be studied plus 5 in. on all sides. A map of the same scale as that adopted for the model, indicating the lines of section to be used, should be fastened to the base. 3. Construction of the Frame (Fig. I).-In the construction of the frame the use of 1/2-in. o.d. pipe welded in a box shape is suggested, with two horizontal rods on each of the four sides, top and bottom. The top rod should be at least I in. higher than the

Jan 1, 1941

By Stephen H. Chung

The blasting performances identified above are considered to be the most practical ones for judging the effectiveness of a design combining explosives / rock / drill pattern. In a total blast design process, productivity relates closely to both fragmentation and heave / displacement of muck. In cast blasting, the more overburden displaced by explosives, the less blasted material there is left to be removed with mechanical equipment such as draglines or trucks. For wall protection and dilution control, estimates of the maximum extent of cracks / damage generated in situ due to blasting will help determine the location for drilling and loading perimeter blastholes.

Jan 1, 1994

By Edmund Shaw

This paper is one of a series being prepared by the United states Bureau of Mines describing mining and milling methods and costs at industrial mineral plants throughout the United states. These papers are designed to disseminate technical information regarding the methods and equipment used. The cost tabulations represent operating expenditures only and not total production costs. It is recognized that publication of total production costs might, in many instances, cause embarrassment to individual producers as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention' of the reader? is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. P. J. Weisel, Inc., with office at La Habra and plant at Corona, Calif., is the only local company that produces sand for the Los Angeles glass factories, although silica sand for other purposes is produced in other parts of southern California and the adjacent portions of Nevada. The deposit at Corona consists of coarse sand imbedded in a whitish clay and differs greatly from the other deposits, which are fine-grained sandstone that must be crushed before it can be screened and washed. The preparation of Corona sand has to be thorough and includes grinding in tube mills, repeated washing and rinsing, removal of dust by air separation, and magnetic separation of iron and other minerals. This requires a plant with a complicated flow sheet. The first plant built did not make a. satisfactory glass sand, and many additions and changes were necessary. It is thought that the present flow sheet will remain substantially unchanged until a new plant is built. The design of a new plant would be simpler, but the process would be the same.

Jan 1, 1937

By Xuehui Zhang, Yun Bai, Qiaosong Li, Huiming Wu

"Construction activities account for a large share of the global Greenhouse Gas emission. In the past 10 years, project decision-makers and researchers have been paying more attention to the carbon emission of tunnel projects. In this paper we study the carbon emission calculation in shield tunneling. The objective of this paper is to: (1) analyze the complex variables which affect the total emission of shield tunneling; (2) develop and illustrate a new data-mining-based method to estimate the carbon emission in the construction phase; (3) assess the emission prediction reliability of a data-mining-based method—the Randomforst model, with R programming language. This study is based on a large-diameter shield tunnel built in Shanghai, China, and shows that a reliable predictive performance can be achieved with this new data-mining-based method. INTRODUCTION Climate change caused by the Greenhouse Gas (GHG) emission has been a hot topic in recent 20 years. Both governments and non-government-organizations are trying its best to control the climate change. Since the 1990s, the general consensus is that carbon emission reduction and carbon sinking (the work of capturing the emitted carbon) are two ways of mitigating the global warming effect, with the former being more exercisable. The challenge posed by global warming also motivates the project decision-makers to take measures to reduce the GHG emission. The 5th Assessment & Report on Climate Change (published by IPCC, the Intergovernmental Panel on Climate Change) suggests that building industry contributes to 5% of the total direct emission. The building industry has shown more awareness of the impact of GHG emissions with construction activities. Shield tunnels act as an important component of the infrastructure system, and have been the dominant way of utilizing the underground space, as well as a competitive alternative to passageway underneath rivers. To study the environmental effects of shield tunneling, there is a need to quantify the carbon emission of shield tunnel construction."

Jan 1, 2016

By P. J. Brereton-Stiles, C. J. Hockaday, I. J. Barker, M. S. Rennie

This paper reports on studies that have been done on the electrical conduction in silicon, ferro silicon, and charge chrome furnaces. A system has been developed that can distinguish between normal resistive conduction and arcing, and this was used to quantify in particular the relative amount of arcing that takes place in these furnaces. It was found that silicon and ferro silicon behave similarly and exhibit a relatively large amount of arcing. Charge chrome on the other hand exhibits considerably less arcing, and the extent of this arcing is highly correlated with the tapping of the furnace. The arcing measurements can also be used online in the control of the furnace, both for the electrodes and electrical circuit, and for the raw materials.

Jan 1, 2007

By F. J. Perzak

The Bureau of Mines conducted a study to develop a standard fire test for 5-gal containers used for storing combustible fluids in underground coal mines. A standard test method was developed which evaluates the performance of the container in a 4-min tray fire. Bureau investigators used the standard test method to evaluate several types of closed 5-gal plastic and metal cans in outdoor tests. Each can tested contained 1 gal of nonfire-resistant (NFR) hydraulic oil. A container failed the test if it lost its contents in any of seven trials. Contents spilled either as a result of thermal rupture or melting. Fewer than 10 pct of the metal containers failed this criterion, but all the plastic containers failed. The metal container failures were usual-ly due to tipping over during pressure relief, which spilled the NFR oil. Replacing the NFR oil in the container with kerosene resulted in failure of more than 30 pct of the metal containers. The standard tests and preliminary tests showed that plastic containers are not equivalent to metal containers in their ability to contain combustibles such as lubricants and greases in a fire. For solvents and lubricants more volatile than NFR hydraulic oil, approved metal safety containers are recommended.

Jan 1, 1985

By Yuhsuke Mizukami

Crude high Cr containing steel such as tool steel, heat-resistant steel or stainless steel is produced by dissolution of high carbon ferro-chromium into molten crude steel. In the refining process, decarburization is performed at the first stage, and deoxidation is followed in the next stage. Therefore, the equilibrium relation between dissolved Cr and 0 in molten Fe-Cr alloy after decarburization is very important when yield of deoxidizer is considered for the ovemll control and optimization of the process. It is well known that the yield of deoxidizer does strongly depend on the kinds of refractories of furnace in the secondary refining process. In the present work, the equilibrium relation between dissolved Cr and O in molten Fe-Cr alloy has been measured in a Cr2O3, MgO or Al2O3 crucible at steelmaking temperature. O contents at given Fe-Cr components have been lower in order of Cr2O3, Al2O3 and MgO crucible. The present results have been discussed based on the activities of the constituents in pure solid Cr2O3, and FeO-Cr2O3, MgO Cr2O3 and (AI,Cr)2O3 solid solutions.

Jan 1, 2003

By Charlie Adcock, Rob Farnfield, Andy Wetherelt

The ISEE Blasters Handbook gives guidance on the level of air overpressure likely to cause occasional window breakage (151dB) and general window breakage (171dB). A long-term safe level of 140dB is also suggested. This guidance is widely used by demolition and other contractors to assess damage zones in the region of explosive applications employing unconfined charges. Other reference material gives more detailed guidance relating to window area, aspect ratio and glass thickness. Despite the guidance given in these references, complaints by members of the public regarding window breakage continue to be received by explosives engineers from air overpressure levels well below the longterm safe limit. Such complaints are not limited to the use of unconfined charges but can even be generated from the highly confined use of explosives in quarry blasting. This paper describes a series of experiments with explosive charges fired in unconfined conditions close to various window configurations. The aim of the work was to test the existing guidance levels and to extend the knowledge base in this area. Topics covered include the role of differential pressure across windows in the walls of an enclosed space such as a room.

Jan 1, 2006

By Fernando Bermejo

El presente texto describe la implementación del método Flash - Flotation para el proceso de optimización de plantas concentradoras polimetálicas en la Compañía minera Raura donde se tienen diferentes gravedades especificas por cada especie mineralógica. Su aplicación comprende la fase de investigación (año 89), modificaciones (año 2002) durante la etapa de escalamiento industrial y la optimización (año 2004) de estos equipos en la empresa, los cuales no han requerido de una gran inversión. Asimismo, los beneficios de operar con la celda SK-80 y SK-240 directamente a la descarga de los molinos primarios, permite optimizar el control metalúrgico. En este sentido, la idea de separar el plomo tan pronto lo permita el sistema, es la forma correcta de optimizar la metalurgia de este en la Compañía minera Raura.

Sep 12, 2005

By J. Guerrero, O. Pavez, N. Toro, A. Nazer

In the 19th century, mining in northern Chile was of great economic importance. Today, the ruinsof the copper smelters and abundant fragments of refractory bricks from their furnaces remain. Therefractory materials have not been previously studied. the origin, physical and chemical properties, and compressive strength of 10 different samples of historical refractory bricks collected on-site were investigated. The characterization results showed that the bricks are silico-aluminous, unlike the magnesium-chromium bricks used by current foundries. It was determined that 90% of them were produced in the UK and 10% were manufactured in Chile. The phases present are mullite, quartz, cristobalite, and tridymite, and the chemical composition corresponds mainly to SiO2. The compressive strength of the historical bricks is similart to those currently used,. These results may contribute to the knowledge of the 19th century mining and metallurgical historical heritage of Chile and the UK.

Jul 5, 2023

By John J. Mahoney, George P. Demopoulos, Matthew T. Bohan

In recent times processing of arsenic-laden complex ores and heightened awareness of the detrimental health effects of arsenic has put an increasing burden on metallurgical operations to remove arsenic from processes for disposal in an environmentally stable form. At present, arsenic is removed and prepared for storage by precipitation of insoluble secondary arsenic-bearing minerals. It has been suggested that Ca(II)-Fe(III)-As(V) phases resembling the natural mineral yukonite, under certain conditions, may have a role in controlling arsenic pore water concentrations in arsenical waste storage facilities. In this study, a previous synthesis method of yukonite (Ca3Fe5(AsO4)4(OH)9⋅4H2O) is revisited and new solubility/stability data is presented based on a modified method.

Jan 1, 2014

By George Otis Smith

WHAT American can enter this Western empire without his imagination being stirred by the stories of its past-yes, and even more by visions of its future! Whether we travel by rail or by auto, our pathway has its traditions of exploration and its records of early settlement. The mountain passes and the routes used by today's commerce are lasting memorials of the pathfinders whose unconquerable purpose was to search out a way-Lewis and Clark, Bonneville, Pike, Long, FrBmont, their names still live in your rivers and lakes and peaks. It was the glory of these adventurers that they spied out the land so that others might follow that long pro- cession of pioneers who occupied the new country- fur traders, gold miners, cattlemen, and homesteaders. Each of these pioneers attacked the problem of transportation in his own way, and each sought by his own method to win the resources whose richness had been reported by the pen of the Government explorer or by the swift rumor of the unnamed and unfamed adventurer. Trails were worn deep by these home or fortune seekers as they passed through the mountain barriers in successive waves-and these were waves that did not ebb, for this was an army of occupation. Along these main pathways of the West, as one historian has pointed out, the figure of chief interest was the sad- faced woman sitting on the front of the covered wagon.

Jan 1, 1926

OFS Branch Committee Meeting held in the Committee Room at the Welkom Club at 4.15 p.m. on Wednesday, 5th March, 1975. Progress in mineral dressing The National Institute for Metallurgy and the South African Institute of Mining and Metallurgy are to hold a symposium on 17th and 18th September, 1975, entitled 'Recent Progress in Mineral Dressing'. INFACON 74 This book of over 300 pages is a record of the First International Ferro-alloys Congress, which was held in Johannesburg from 22nd to 26th April, 1974, under the auspices of the Ferro Alloy Producers' Association of South Africa, the National Institute for Metallurgy, and the South African Institute of Mining and Metallurgy. NIM reports Report no. 1595 Preliminary tests on low-grade brecciated fluorspar ore from the Ottoshoop district. (5th Nov., 1973, declassified April 1975). Report no. 1612 Flotation tests on sulphide-bearing high-grade brecciated and wad ores. (20th Mar., 1974, declasl>ified April 1975). Report no. 1643 Further tests on low-grade brecciated fluorspar ore from the Ottoshoop district. (12th Jul., 1974, declassified April 1975). Report no. 1654 The determination of osmium in platiniferous media. Report no. 1689 The determination, by atomicabsorption spectrophotometry, of arsenic, selenium, tellurium, antimony, and bismuth on ion-exchange restns. Report no. 1715 Flotation tests on various types of ore from the Ottoshoop district Report no. 1730 The chromitite from the Marico occurrence, western Transvaal, its alteration, and possible reasons for its refractory nature. Report no. 233 A chemical and mineralogical study of microlite from the N oumas pegmatite. 24th Geomechanics Colloquy The above Colloquy is to be held on 2nd and 3rd October, 1975, in the Salzburg Congress Hall. Rosenhain centenary The centenary of the birth of WaIter Rosenhain (1875-1934) will be celebrated by an international conference to consider how physical metallurgy has contributed to engineering practice. Iron and steelmaking The Centre de Recherches Metallurgiques (CRM) and the Verein Deutscher Eisenhiittenleute (VDEh) are jointly to hold the International Meeting on Iron and Steelmaking 1976 in Brussels from 17th to 18th May and in Diisseldorf from 20th to 21st May, 1976. International Symposium on Mine Surveying The III I.S.M. is being held in Leoben, Austria, from 28th June to 3rd July, 1976. Book review Tenth International Mineral Processing Congress. 1973. London, The Institution of Mining and Metallurgy. 1208 pp. £20. Particles A course on particle characterization and a symposium on experience in the applications of particlesize analysis will be held during the last week of July in Pretoria and Johannesburg. A.S. & T.S. Trust The A.S. & T.S. Trust was formed on 24th March, 1972, to mark the Golden Jubilee year ofthe Associated Scientific and Technical Societies, with the object of advancing science and technology in South Africa. Second International Congress of Engineering Geology The Proceedings of the above Congress, which was held in Sao Paulo, Brazil, from 18th to 24th August, 1974, are now available.

Jan 6, 1975

Train on Different Equipment - * Immersive?s interchangeable cabin controls technology - ?clip on & off? * Change Simulator from one machine to another in minutes * No technical expertise required to swap * Real, functioning, controls and displays are used to aid rapid learning Immersive has produced a range of Conversion Kits to suit most equipment. Modular design - Easy to convert from one machine model to another with a Conversion Kit. Caterpillar Models Trucks - 769D, 773D, 777D Trucks - 785B, 789B, 793B Trucks - 785C, 789C, 793C, 797 Excavator/Shovel - 5130, 5230 Front end loader ? 992, 994 Dozer ? D10, D11 Komatsu Models Trucks - HD325, 785-5, 985-5 Trucks - 730E, 830E, 930E Dozers - D375A-3, D475A-3 Shovel - PC8000 P&H Shovels - 4100A, 4100XPB, 4100BOSS Hitachi Shovels - EX2500, EX5500 O&K Shovel - RH200 Bell Articulated Truck - B40C

May 1, 2003

By Carl W. Kelley

PRODUCTION in the United States of carbon black has increased from 20 million pounds per year in 1920 to over 2 billion pounds in 1964 valued at $156 million, mostly for consumption by the rubber-tire industry, which uses over 90 percent of total production. Production of over 2 billion pounds in 1964 is a 7.8-percent increase over 1963 and is the first time furnace black production has topped 2 billion pounds. Although 1964 channel black production dropped 6 percent below 1963, carbon black produced by the furnace process, which ac-counted for 92 percent of total production, increased 9 percent to 2,053 million pounds. Total shipments during 1964 amounted to 2,245 mil-lion pounds, a 7 percent increase. This growth parallels the expansion of the automotive and petroleum industries. Along with this expansion have been many advances, both in methods of manufacture and in the quality and variety of blacks available to industry. There are several kinds of carbon black, thermal, channel, furnace, lamp, and oil blacks. Until recently, channel has been the important black in rubber compounding. Following the introduction of the synthetic GR-S, and more recently of "cold rubber," it has been found that certain furnace blacks with particle size larger than that of the standard channel black give superior reinforcement. A great advantage of furnace black is that its yield per unit of gas feedstock is higher than that of channel black. The 184-million-pound increase in domestic carbon black sales was partially offset by a 37-million-pound decrease in exports. Decrease in exports especially to Europe, is expected to continue. In Europe, as in the United States, the major end use for carbon black is in the manufacture of automobile and truck tires. Although the number of automobiles in Europe is predicted to grow by about 7.5 percent per year, compounded until 1975, the increased demand will be met by a 20 percent increase in existing capacity and by the new plants being built in Europe by U.S. companies. Also) aromatic oils for producing furnace blacks are plentiful now that western Europe's chemical industry is switching to a petroleum base.

Jan 1, 1965

By F. X. Tartaron

Behavior of hard-burned quicklime was compared with that of soft-burned quicklime in an oxygen converter utilizing oxygen blowing in a rotating cylindrical vessel, set at a 30° to 60° angle to the horizontal and operated at a predetermined speed of rotation. Four pairs of tests were made) each comparing hard lime with soft lime. Three of the pairs differed from one another in the quantity of lime employed) and the fourth differed in blowing time, All four pairs showed an increase in yield when soft lime was used. Three of the pairs revealed that the ratio of the oxygen consumed with soft lime to the oxygen consumed with hard lime was the same as the ratio of metal yield with soft lime to the metal yield with hard lime. The fourth pair contained an error and could not be included. Finally, a close inverse relation was found between the combined iron in the slag and the combined lime in the slag, which can be expressed by the equation pct Fe = 52.67 -0,906 (pct CaO).

Jan 1, 1967

By George Weinman

GEORGE WEINMAN: Our first group leader for the discussion, "Ups and Downs of Downsizing," wishes to remain anonymous. ANONYMOUS PRESENTER: When George and Jamie asked me to do this, I thought a while about what to say and went through several variations of what I’ll present today. I came up with the title "Ups and Downs of Downsizing." A lot of downsizing has occurred in all of our industries-mining in particular. While this downsizing has gone on there's no doubt that all of us produced more and more, probably with less and less people and less and less resources. But I contend that there's also a big downside associated with this. I disagree with a point made in the keynote presentation yesterday, the point being that vendors are bringing new technology to us. I can agree that the major changes associated with equipment and similar items are being brought to us by vendors. But I do contend that there's an awful lot that's getting away from us-especially if you factor in the integrated supply or the strategic alliance or the various and sundry related purchasing techniques. I contend that we are missing a lot of, let's call it, lesser technology; not major equipment changes, but different tools, different techniques for doing things, different left-handed widgets. The integrated suppliers, to some degree, are bringing this to us; but I am concerned about the small guy who comes up with a good idea but deals through integrated suppliers rather than having direct contact with plant people. They're probably going to go somewhere else and market their wares. That's what I'm hearing from a lot of smaller vendors. I also think that we are losing a lot of our knowledge base. Every time you shrink an organization somebody leaves. The bottom line: less people. When a person leaves-and I don't care who he or she is, be it the janitor who's cleaning the bathroom, the operator, the engineer-when that person leaves there's some knowledge that goes with that per- son. And sometimes that knowledge is quite valuable. I've worked more or less at the plant "low." I can't tell you how many excellent, viable projects have come from people who said, "Look here. There's a better way of doing this." And, you know, they were right. Now, maybe they didn't have the resources or the expertise to develop these ideas into full projects, but they had that basic idea. Someone may say, "Well, if we put a no. 6 skyhook here, so we can lift this particular pump without bringing a crane from 30 miles away ...." No. 6 skyhooks are a bit expensive, but what if we put together a little structural steel here or whatnot?

Jan 1, 1998

By J. Y. Liu

The comminution in a high-pressure roller mill is modeled by an energy-based population balance approach considering three aspects of breakage taking place in the active zones of the mill: the interparticle breakage in the high-compression zone, the breakage at the edges of the rolls, and the pre-breakage in the acceleration zone. Together with an appropriate model of classification, this model can be used to simulate steady-state performance of closed-circuit grindings with high-pressure roller mill. After a brief description of the basic modeling approach, the algorithm of the steady-state calculation for a generalized grinding-classification circuit is presented, from which the circuit configurations commonly met in industrial practice can be derived. With an iron ore as feed material for example, simulation results are shown and discussed in respect of circulating load, specific energy consumption and product fineness for closed-circuit grindings under various operating conditions. The effects of stressing intensity, working gap, classifier parameters as well as circuit configuration on the overall circuit performance are investigated systematically by means of computer simulation.

Jan 1, 2014

By M. N. Brodie, John Chapman

INTRODUCTION - DEFINITION & HISTORICAL PERSPECTIVE While this symposium is concerned with comminution which, by definition, relates to all stages of size reduction of an ore body to a form suitable for mineral separation, the electrical drive aspect of the grinding section will receive most attention in contrast to the crushing, screening and materials handling elements of the process. The reason for this is that today's large mills, thirty feet diameter and upwards, present mechanical and electrical problems which require a degree of sophistication in their solution not previously required. The ability to satisfy these demands, so far as electrical technology is concerned, largely results from the development of semi-conductor devices. These can now handle typical electrical distribution power levels within remarkably s m all volumes and with high efficiency when compared with the motor-generator sets, mercury arc rectifiers, rotating amplifiers, magnetic amplifiers and vacuum tubes which were commonly used to provide speed and torque controls as recently as the early nineteen-sixties. The hardware available to the electrical engineer has changed dramatically whereby even the simplest control system formerly using hard-wired relays is now superseded by the program m able logic controller with its computer-like memory containing the sequence of operation, in other words, the software. Reverting now to the mineral process itself, it is assumed that the ore body has been mined using explosives and is delivered to the concentrating plant in its 'run of mine' form. The problem becomes one of reducing the material to a size which will permit an acceptable recovery of the mineral with the most economical use of energy. The size of 'run of mine' material will range from about minus five feet for high tonnage open pit operations to minus two feet for the smaller underground mine. The final reduction in size may range from minus ten mesh to minus two hundred mesh (exceptionally as fine as minus six hundred mesh) depending upon the concentration method and dissemination of the mineral values within the ore. There is no single circuit that satisfies all applications, but the pattern of metallurgical equipment use shown in Table 1 appears discernable from current practice, in general terms.

Jan 1, 1982

By Jon Errey, Aleksandar Petrovic, Karl Haase

"Developing a gold deposit of this magnitude in the Amazonian jungle of Guyana posed many challenges. This paper describes not only the process & logistical challenges arising from the remote mine site location in a tropical environment with a local industry unaccustomed to recent large scale gold mining operations, but also the innovative technical solutions employed to address the unique ore body characteristics. The best examples of this approach were dealing with the initial high clay content saprolite ore from the development phase and primary mining pits whilst ensuring that the design also implemented the right method to deal with the future fresh rock in an environmentally sensitive habitat. In order to do this separate individual crushing flowsheets were generated, focusing on the specific material handling equipment that would be suitable to handle these various types of material and ensure high recoveries were maintained.INTRODUCTIONAurora gold mine is located in forested region of Guyana, 170 km west of capital Georgetown, and 130 km West North-West of Bartica, a settlement at the junction of the Essequibo and Cuyuni Rivers.The Aurora gold project (Aurora) is a 5,000 tonne per day open-pit/underground operation, which will produce a total of 3.29 million oz. gold – averaging 194,000 oz. per year – over an initial 17 year mine life. At the final investment decision in 2014 Aurora had a total resource of 6.54 million ounces in the measured and indicated categories (62.83 million tonnes at 3.24 g/t Au) as well as additional 1.82 million ounces in the inferred category (16.93 million tonnes at 3.34 g/t Au)."

Jan 1, 2016