Search Documents

Experimental studies on viscosity of titanium bearing slags have been reviewed and the assessed data were used in extending the capability of the structurally related viscosity model for silicate melts, developed by the present authors. Experimental data on ternary and higher order systems containing CaO, MgO, MnO, FeO, Al2O3, TiO2, Ti2O3, SiO2were assessed and used. The newly extended viscosity model represented the viscosity behaviour over broad temperature and composition ranges. The structural role played by TiO2and Ti2O3in silicate network structure is discussed with respect to their effect on viscosity of melts. Keywords: viscosity model, TiOx containing silicate melts, silicate network structure.

Jan 1, 2004

By József L. Margitfalvi

Different Au/MgO catalysts modified with Mn, and Fe were prepared by precipitation-deposition. The catalysts were characterized by XRD, FTIR, Temperature Programmed Reduction (TPR) and CO chemisorption and were tested in CO oxidation in the temperature range of 243-523 K. The catalytic tests using both Temperature Programmed Oxidation (TPO) technique and time on stream (TOS) experiments revealed the high activity of catalysts prepared. In TPO experiments the modification by Mn significantly increased the activity above 300 K, however in the subambient temperature range the activity decreased considerably. Catalysts modified by iron did not show any decrease in the activity below 300 K, while the activity at high temperature increased significantly. Catalysts modified by Mn, Fe showed higher activity, selectivity and stability in preferential CO oxidation, carried out in the presence of hydrogen than the unmodified Au/MgO catalysts. Results of in situ FTIR spectroscopy on both the base Au/MgO and the iron modified catalyst unambiguously revealed the formation of ionic gold in the presence of CO/O2 mixture. The formation of this species was strongly hindered in catalyst modified by manganese. Results obtained strongly support the need for the formation of "metal ion - metal nanocluster" ensemble sites. These sites are involved in the activation of the CO molecule prior to its reaction with atomic oxygen. It is suggested that at subambient temperature these ensemble sites contain mainly ionic forms of gold, while at higher temperature iron or manganese ions are involved in CO activation.

Oct 1, 2003

By Andrew B. Cecala

The U.S. Bureau of Mines has designed and tested a system called the Bag and Belt Cleaner Device (B&BCD) to reduce dust levels in and around the bag conveying and stacking process. The device physically cleans either 22.7 kg (50 lb) or 45.4 kg (100 lb) paper bags by using a combination of brushes and air jets. It is completely self-contained and is kept under negative pressure by a baghouse to ensure that dust and product removed from the bags during cleaning does not flow into the work environment and contaminate workers. The bags travel through the device on a chain conveyor, which permits any product or dust cleaned from the bags to fall into a hopper at the bottom of the device and be recycled back into the process via a screw conveyor. Once exiting the B&BCD, the outside of the bags and the conveyor are essentially product and dust free. The B&BCD was evaluated at two mineral processing plants to determine reductions with the device in use. The results of both field evaluations showed that the amount of product removed from the outside of the bags varied from 77 to 93 pet.

Jan 1, 2010

By K Hobbs

Mining is experiencing a difficult period of low profitability and declining productivity. To achieve sustainability, mining companies are challenged with improving output, quality and safety while decreasing costs. At the same time, organisations are having to manage a workforce in which individuals no longer accept a traditional style of management, employees prefer more flexible employment, and diversity within teams is becoming the expected norm.Increasing organisational diversity has been shown to have a positive impact on performance and therefore sustainability. Gender diversity and equality between working men and women is the area most studied in this regard. Executives are becoming more aware of the correlation between gender diversity and performance with some larger organisations having dedicated resources to increase the number and status of women in their organisations. Despite this, limited improvement in gender equality is apparent globally over the last decade with some industries, including mining, going backwards. So why is this the case and what other strategies are available?In 2015, the United Nations Women National Committee Australia (UN Women NCA) in conjunction with Autopia released a white paper discussing the lack of visible change in gender equality despite the widespread implementation of merit-based personnel management strategies. Using research from around the world and thoughts from influential government, education and business leaders, the paper ‘Rethinking Merit’ debunks the myth of the meritocracy. It provides a number of recommendations for organisations committed to improving their performance and sustainability through diversity, including a variety of real-life company examples, instead of relying solely on merit-based decision-making.This paper takes the recommendations of ‘Rethinking Merit’ and applies them to the mining industry. It shows the relevance that rethinking merit has for the industry and why applying the recommendations can result in an increase in diversity, therefore enabling greater performance and sustainability of mining companies. This paper provides case studies from Aurizon, Iluka Resources and BHP Billiton and, as a guide for managers, a generic diversity strategy designed to be implemented alongside traditional merit-based personnel management techniques.CITATION:Hobbs, K, 2016. Rethinking merit for a sustainable mining industry, in Proceedings International Mine Management Conference, pp 139-154 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By Phil W. Welch

At first glance, the similarity between the fine grinding of cement clinker and coarse grinding done in other mineral processing industries may seem remote. However, it is interesting to note that the mill discharge fineness of cement clinker is only 70 to 90% passing 100 mesh and quite comparable to other mineral processing grinds. There is however, a greater dependence of the mill on the air separator in the finish grinding of cement clinker than in other mineral processing industries which explains why a technique to guage the balance between a mill and separator first began in the cement industry. (1) More recently an adaptation of this technique has shown its application to the processing of phosphate rock and is the central topic of this paper. First, an explanation of work done with fine grinding cement circuits seems appropriate together with a few general comments regarding cement. When unground or partially ground cement clinker enters a finish grinding mill, it is subjected to mechanical forces of impact and attrition which gradually reduce it to a range of sizes characteristic of finish cement. That is, a range of approximately 1 to 125 microns. The large proportion of superfine particles relative to the coarse and intermediate size particles is typical of portland cement particle size distribution. It accounts for the workability characteristics of plastic concrete and the early strength development of concrete which is so necessary to its successful use as a construction material. For this reason It is quite evident from quality control tests when a shortage of superfines exists.

Jan 1, 1975

By Kenneth P. Neumann

The development of the Cyprus Thompson Creek Molybdenum Deposit near Challis, Idaho, began in 1967 when the first mining claims were staked on the intrusive rock outcrop. Exploration drilling continued for the next 14 years. During 1978, a decision was made to develop the deposit. In December, 1980, approval of the Environmental Impact Statement was received and construction of facilities and waste rock removal began. By the middle of 1983, 126 M metric tons of rock had been removed and all facilities were completed. The high work ethic of Cyprus Thompson Creek employees combined with innovation has made the mine one of the most efficient in the United States today.

Jan 1, 1983

By William Crowe Kellogg

By now the term AFMAG has been fairly well introduced to the mining industry. Several papers have been presented and published concerning AFMAG (references 1 and 2). However, the term AFMAG remains rather new to the industry, and the exact place which AFMAG occupies in the minerals exploration field is still somewhat uncertain in the minds of many who may have use for this new and interesting method of electromagnetic exploration for conductive minerals. It is the purpose of this paper to again review the basic theory of the AFMAG system, to describe and - illustrate the equipment and data presentation as used in aerial surveying, and to provide some idea of the cost and nature of airborne AFMAG surveys. This paper is primarily of a general descriptive nature and presents AFMAG theory in a schematic rather than mathematical form; emphasis is placed on the equipment, the present method of data presentation and survey operations, since it is believed that such, information will now generally best serve to inform the mining industry of the characteristics of the AFMAG system.

Jan 1, 1960

By Donald Babbitt

In 1971, during the planning and design stages of a $300 million expansion, the Iron Ore Company of Canada Ltd. through its Engineers, Canadian Bechtel Ltd., came out with a preliminary request for two (2) 10,000 LTPH belt conveyor scale systems. These Systems were to provide weighing accuracies within 2.5% of the iron ore pellets and concentrates in transit on two (2) 72" wide conveyors from the stockpiles to the ships. Each conveyor system would be fed by a rail mounted bucket wheel reclaimer, with the conveyed material moving directly to the ship loaders with no inter- mediate surge and/or storage bins between the stockpiles and the ships. The bucket wheel reclaimer discharge rates would vary from 0-9600 LTPH in cyclic periods, with the periods varying from 1-5 minutes - dependent on the level of the reclaim buckets in relation to the stockpile as well as the slewing rate of the reclaimer. There would be frequent interruptions for bucket wheel repositioning (laterally and vertically), changing ship holds, and trimming ship holds. These frequent zero flow conditions, approximately 500 per 150,000 ton ship, could last 1-5 minutes. In addition, the conveyors on which the scales were to be mounted would be over the water and subject to the wind and cold of Northern Quebec. These Systems would be in use 350 working days of the year and would load 30,000,000 LT/yr. (An average of 90,000/working day).

Jan 1, 1975

By J. Jorge, J. Mariño-Salguero, B. Álvarez-Rodriguez, J. M. Menéndez-Aguado, J. J. de Felipe

"This work focuses on the characterization of heat generation during dry fracture by direct impact of a tantalum ore. Moreover, an attempt was made to quantify the heat energy loss to the environment during the grinding process of a ball mill. The study was carried out using mineral samples from a Spanish mine that were characterized by measuring their density and specific heat. During the experiments, increases of temperature ranging from 5.9 to 7.3 °C after the fracturing process were observed. A numerical model was then applied to calculate temperature distributions through the mill wall. Three possible combinations of heat transfer coefficients were analyzed, from (1) Kapakyulu and Moys, (2) Duda and (3) the heat transfer laboratory of Universitat Politècnica de Catalunya. The models with the coefficients from Kapakyulu and Moys and the heat transfer laboratory of Universitat Politècnica de Catalunya were found to provide results that were in best agreement with the experimental data. IntroductionEvery year, several billion tons of metallic ores, minerals, cement and other solids used in the ceramic and chemical industries are subjected to size reduction in ball mills around the world. The U.S. Department of Energy (2005) reported that in the United States about 29 percent of the total energy used by the mining industry, or 0.4 percent of total U.S. energy consumption, is used in comminution. In Canada and Australia, comminution is responsible for about 2 percent and 1.5 percent of total energy use, respectively. In nonindustrialized countries where mining constitutes higher fractions of their industrial sectors, comminution costs represent a significant contribution to mine operating costs. The specific energy consumption values for the grinding of these materials typically range from 5 to 50 kWh/t. Thus, a significant amount of electrical energy is consumed in the ball mill grinding operation (Aguado et al., 2006; Gupta and Sharma, 2014). Grinding can represent up to 50 percent of the direct operating cost in a mineral processing plant, especially as comminution devices operate in highly inefficient ranges of 4 to 8 percent (Wang, Yang and Yu, 2012)."

Jan 1, 2017

"Pilot plants for pressure hydrometallurgy represent special design and project execution challenges. Over the past twenty years, Zeton has designed and fabricated a variety of world-class pressure hydrometallurgical pilot-plant facilities, and this paper discusses design considerations and strategies related to such projects. Project execution methods are also discussed, and guidance is given for the selection of materials of construction and for the selection of appropriate pressure and temperature design points for pressure hydrometallurgical pilot equipment. The paper concludes with a discussion of the need for process similarity with future commercial operations and the realities of pilot-scale equipment.INTRODUCTIONThe process technology developer or owner and the designer/fabricator of a new pilot-plant facility are faced with some difficult technical choices even after the decision to build a dedicated plant has been taken. A pilot-plant project is usually on the critical path of a large commercial project involving investments many multiples greater than the capital cost of the pilot plant. Schedule savings in the design, manufacture, and commissioning of the pilot plant or in a rapid completion of the experimental program can be disproportionately beneficial to the overall development project. However, inappropriate shortcuts resulting in major oversights can be disproportionately problematic.A number of considerations and suggestions for both the project execution approach and the process engineering design of pressure hydrometallurgical pilot-plant facilities are presented as a guide for potential owners and operators of new pilot-plant equipment and facilities."

Jan 1, 2012

For handling rough rock, the shovel-train system is unexcelled. The ideal application is a physically large, but not excessively deep, open-pit mine from which the coarsely blasted ore and waste must be transported distances in excess of three miles. If, in addition, a high production rate is to be maintained, railroad haulage will probably afford a lower cost per ton transportation than will any other haulage method. Relatively gentle grades must be employed- usually 3% for uphill hauls and 4% for downhill hauls. The greater the differences in elevation the greater are the railroad track grade space requirements. By way of illustration, a 3% ramp out of a pit only 300 ft deep must be almost two miles long. Mainline track locations should be selected carefully so that the frequency of movements during the life of the mining operation is minimized. This applies both to ore and to waste haulageways. Such moves are not only expensive but difficult to execute without adversely affecting production rates. The large mine affords greater opportunities for judicious location of semi-permanent trackage.

Jan 10, 1967

By Y. A. Chang, J. Woodford, C. R. Kao

Reactive diffusion studies between NbC and Si were carried out at 1300 °C under a vacuum of 10-5 torr and a uniaxial pressure of 1 MPa. The annealing time ranged from 8 to 100 hours. The Si used was single crystal silicon; the NbC was hot-pressed powder compact. A NbSi2+SiC two-phase reaction layer formed with NbSi2 as the matrix and SiC as discontinuous particles. The microstructure of the reaction product is homogeneous, dense, and fine. The NbSi2 grain size and SiC particle size are in the micron range. The growth of the reaction products follows parabolic kinetics. Extrapolation of the data to zero thickness suggests an apparent incubation time of 3.5 hours. However, for short annealing time «60 hours), the thickness data can be approximated by linear kinetics with an initial growth rate of about 2 11m/hr. Based on these experimental observations, a growth mechanism for the reactive diffusion between Si single crystal and NbC powder compact is proposed. We propose that the nucleation sites for the SiC particles are at the voids of the NbC powder compact. This proposed nucleation mechanism offers a potential way of controlling the SiC particle size by changing the void size and void density of the NbC powder compact. This hypothesis, if proven to be true, will allow us to control mechanical properties of the composites by tailoring the SiC particles formed. It is also pointed out that the microstructure requires Si to be the dominant diffusing species and to diffuse through the reaction layer, while Nb and Conly have to undergo local rearrangement.

Jan 1, 1996

By B. Beatty

Discussion by B. Beatty This is a response to M.J. Hrebar's paper, which tracks in detail the highly productive stripping capabilities of modern large bulldozers at two separate installations. It proves the old adage "economies of scale" and quantifies the advantage of being able to move large loads of dirt over comparatively short haul distances by sliding rather than carrying the load. This discussion examines whether a bulldozer is the most efficient way of using this geotechnical principle. Case 1 - Study eastern US: Contour coal stripping application The energy consumption for the Case 1 mining method (eastern US contour stripping operation) shows the D11 averaged 117 L (31 gal) of diesel fuel per scheduled hour, and produced 333.3 bank m3 (436 bank cu yd) per scheduled hour (0.351 L/m3). Assuming 1 L (0.26 gal) of diesel fuel contains 10.4 kW-hr of energy, the unit expenditure of fuel energy for Case 1 Study was 3.66 kWh/m3. Another way of shifting this material is by using an overburden slusher (OS), as shown in Fig. 1. The OS as shown in Fig. I. The OS is electrically powered and consists of a manned low wall winch (LW ), a remote controlled (radio telemetry) highwall winch (HW) and a hoe. The winches operate to pull the hoe back and forth across the pit. The hoe carries load in the forward direction ahead of a rear mounted blade and returns empty. A spreadsheet (Lotus 123) simulation package, BOSSIM, models the OS operation on a load by load basis over a wide range of pit configurations. The geometry shown in Fig. 2 of the paper was modeled using BOSSI M and the results are summarized in Table1. Table 1 shows a LW with 150 kW (200 hp) and a HW of 120 kW (160 hp) installed power, towing a 15-m3 (19-cu yd) hoe, would accomplish the Case 1 stripping task at about the same scheduled stripping rate (D11=333 m3/hr or 433 cu yd/ hour, OS=342 m3/hr or 447 cu yd/ hour). It was assumed the winches in this equipment have an electromechanical efficiency of 90%. This gives an average electrical energy expenditure rate of 151 kW-hr, and a unit energy expenditure level of 0.44 kWhr/m-3(0.57 cu yd/kWh)-an improvement of 8291%- over the D11 alternative. The energy comparison illustrates the importance of using more efficient electric power if possible, ahead of the internal combustion engine, and delivering power from a fixed ground position rather than through a moving track system. Another important energy observation is the comparative action of the dozer blade and the OS hoe. The former implement continuously digs and spills as it works the load forward. The OS hoe digs the load until full, the blade then lifts due to the contained load pressure and a shear plane forms under the mass, enabling it to slide forward in a force reduced - transporting mode. Economic comparison Table 2 operating cost per scheduled hour and unit cost comparison follows a format used in Tables 2 and 3 of Hrebar's paper and compares Case 1 Study with the OS alternative. Drill and blast costs are kept constant in both cases, although when larger OS units are considered, it is expected these costs will reduce because bigger hoe sizes will permit larger rocks to be transported efficiently.

Jan 1, 1995

The copper-clay deposits consist largely of goethite and clayey mudstones carrying native copper, cuprite, and chalcocite. The mudstones are of Ordovician age, are interbedded with Fe-Mn carbonates, and probably contained syngenetic iron and copper sulphides. The secondary copper minerals have been derived from post-Devonian weathering in situ and also by deposition from surfaee and underground waters draining the adjacent mineralized volcanic rocks.

Jan 1, 1969

By Kyoosang Yoo

The report presents the results corresponding to the analysis of a lining system for tunnels in soil and soft rock in creep-active ground. The purpose of the analysis is to evaluate the performance of a lining at each construction stage. The steps include: 1. Accurate representation of the initial undisturbed state of stress 2. Excavation, 3. Lining installation 4. Injection of mortar and its curing, and 5. Short-, medium- and long-term creep behaviour in the surrounding soil/rock. The response of a prototype tunnel is simulated using the computational finite element framework MSC.marc2008.

Jan 1, 2010

By Wenxian Zhu, Xuema Li, Patrick R. Taylor

"Experiments were performed in a non-transferred arc, thermal plasma flow reactor to investigate the synthesis of ultra fine boron nitride (BN) powder from the reaction system of boron oxide (Bz03), methane (CH4), ammonia (NH3) and hydrogen (H2). Argon (Ar) and nitrogen (N2) were used as plasma gases. The thermodynamics and kinetics of the synthesis reactions were examined and a chemical reaction mechanism was proposed. The powders produced under certain operating conditions had high purity and good conversions. All the products were extremely fine powders (< 30nm) and were uniform in size distribution. The powder products were analyzed by chemical and physical characterization. The effects of the reaction variables on the conversions from B203 to BN and the purity of the products were investigated.IntroductionIn the past few decades, boron nitride (BN) has attracted a great deal of interest because of its excellent thermal, chemical and electrical properties (1-4) It has a high thermal stability and thermal conductivity. Chemically, it is very stable and is not wetted by most molten metals and slag. It is also an excellent low loss insulator. Since hexagonal boron nitride (h-BN) is light in weight, strong and easily fabricated, it has applications in a variety of specialized high temperature areas, such as a high temperature lubricant, crucibles for molten metals, thermocouple protection tubes, break rings for horizontal continuous casting of steel, and friction reducing coatings. In cubic form, boron nitride is one of the hardest materials known, second only to diamond, and it is an excellent material for tools in which the use of carbon based materials is limited by oxidation or reaction with metals."

Jan 1, 1998

By D. D. Rabb

Originally, the term solution mining applied to a dissolution, washing, or "brining" of soluble salts such as halite (common table salt), potash or trona. After the mid-sixties, however, the definition has been expanded to include heap and dump leaching, in-place (in situ) leaching, removal of oil from tar sands, extraction of sulfur from deep wells by the Frasch process and the recovery of metalliferous solutions from geothermal sources. Solution mining is also known as borehole, non-shaft, or chemical mining; the extraction of soluble mineral values from a variety of ores using appropriate solvents and chemicals. Solution mining frequently involves chemical changes; for example, copper usually goes into solution as copper sulfate, gold and silver as a cyanide compound, and uranium as a sulfate or uranyl tricarbonate. The valuable constituent is removed from the solid body of the ore by mass transfer to a aqueous solution.

Jan 1, 1986

By E. Jackson

This paper describes highlights of the Placer Dome MiniMole project - the development and testing of a robotic machine for mining narrow ore veins. A prototype hydraulically controlled robotic machine was built and tested. The machine provided a platform for testing numerous cutters in the field. Other cutters, e.g. undercutting devices, were tested in the lab. Extensive analyses were done on specific energies and cutter penetration. Three sets of quarry trials were done, then the machine was tested in an underground mine. Rock UCS values varied from 180 MPa to 230 MPa. The paper includes lessons learned and recommendations based on the project findings.

Jan 1, 2007

By J. W. Downey, M. V. Nevitt

The phase boundaries for the 950" isothermal sections in the ternary systems Zr-Co-0 and `Zr-Ni-0 have been determined for the composition range from 50 to 100 at. pct Zr. The two systems show very similar phase relations, having no extensive solid solution phase fields. Each contains a ternary phase. These phases are apparently isostructural, but their structure has not been determined. Some aspects of the phase relations are discussed in terms of the alloying behavior of transition metals. THE work described in this paper is the outgrowth of a recent study of the occurrence of phases having the Ti2Ni-type structure (structure-type E9,) in certain ternary systems involving Ti, Zr, or Hf with another transition metal and O.", In the Zr-CO-0 and Zr-Ni-0 systems no Ti2Ni-type phases were found to occur. However, there are several interesting aspects of the phase relations in the two systems which have significance from the point of view of the alloying behavior of transition metals. The results of this investigation may also have some importance in studies of the oxidation of Zr-Co and Zr-Ni alloys. In both the Zr-Co-0 and Zr-Ni-0 systems only the 950" isothermal sections were investigated and, as a further restriction, the study was limited to the composition range from 50 to 100 at. pct Zr. A tentative Zr-Co binary diagram has been published by Larsen, Williams, and Pehin. In the composition range pertinent to the present work they report a eutectic at 980°C and 75.9 at. pct Zr, the products of which are the terminal solid solution based on /3 Zr and the compound Zr2Co, and a eutectic at 1080" and 64.8 at. pct Zr whose products are Zr,Co and ZrCo. The solid solution based on /3 Zr is shown to decompose eutectoidally at 826°C into a Zr and Zr2Co. The limits of solubility of Co in a and /3 Zr have not been established. The structure of Zr2Co is not identified in the publication just cited. Dwight has reported that ZrCo has the CsC1-type strcture. The Zr-rich portion of the Zr-Ni diagram has been determined by Hayes, Roberson, and Paasche." The phase relations are very similar to those of the ZrCo system. A eutectic reaction whose products are /3 Zr containing 2.9 at. pct Ni and Zr,Ni occurs at 961°c, and a eutectic between Zr,Ni and ZrNi is found at 985". The solid solution based on /3 Zr decomposes eutectoidally at 808°C. The solubility of Ni in a Zr is not known accurately but is believed to be very small. Smith, Kirkpatrick, Bailey, and Williams7 have found that Zr2Ni has a tetragonal structure of the A1,Cu-type and that ZrNi is orthorhombic. Domagala and McPherson8 have published a constitution diagram for the system Zr-ZrO,. At 950" their diagram indicates that the solid solution of 0 in 0 Zr is stable from 0 to 0.5 at. pct while the phase field of 0 in a Zr extends from 6 to 29 at. pct. These solubility limits were adopted in the present study and no binary Zr-0 alloys were made. No previous data on the phase diagrams of the ternary systems are known to exist. EXPERIMENTAL PROCEDURE The experimental details involved in the preparation of alloys in this laboratory by arc melting have been described in several previous papers"3 and they will not be repeated here. Information concerning the purity of the metals used is given in Table I. Oxygen was added in the form of reagent grade ZrO,. All of the cast specimens in both alloy systems were annealed in air-atmosphere tube furnaces at 950 3&apos; for 72 hr and water quenched. The specimens were protected from oxidation by wrapping them in Mo foil and sealing them in quartz tubes that had been evacuated at room temperature to a pressure of 1 x 10B mm of Hg. The phase boundaries were determined by metallography, and identification of the phases was accomplished primarily by X-ray diffraction methods which employed a powder camera having a diameter of 114.6 mm. The diffraction techniques which are in use in this laboratory have been previously described.&apos; An etchant that proved satisfactory for most of the alloys consisted of 5 pct by vol of AgNO

Jan 1, 1962

By Martina Cadorin

Activated nanoporous biocarbon (aNBC) was prepared using E. grandis wood as a precursor material. Oxidated activated nanoporous biocarbon (ox-aNBC) sample was obtained from the aNBC by oxidation with nitric acid. The samples were tested as Pt nanoparticles catalysts support for ethanol oxidation reaction and as electrode materials for supercapacitors. The porous structure, chemical properties, and the structural and morphological characteristic of the materials were correlated with their electrochemical behaviour. Biocarbon materials showed similar high specific surface area. The oxidation treatment increases the content of the oxygenated and nitrogenated surface functional groups but without appreciably change in the nanostructure characteristic. The aNBC supported Pt nanocatalyst has better electrocatalytic performance for EOR. Oxygenated functional groups have a marked effect on the supercapacitors electrode behaviour, increasing the total electrical capacitance by pseudocapacitive contribution, but with a negative effect on the cell electrical resistance and cell response time.

Oct 30, 2017