Search Documents

By Madan M. Singh

Hydraulic mining has been practiced in the United States since 1852 and many mineral commodities, such as gilsonite, phosphates, lead-zinc, silver ores and St. Peter Sandstone can be mined in this manner. In 1958, the U. S. Bureau of Mines initiated research into the mining of coal using these techniques.1-4 These early investigations were conducted in the 5000 psi pressure range. The large nozzle diameters used in this pressure range produced extremely high flow rates which created visibility problems at the coal face, and required removal of large amounts of water from the mining area. Besides, the production rates were not much better than with mechanical methods. This indicated that with higher pressures the water quantities might be reduced using the same or higher horsepowers but enhanced breakage. For this reason intensive investigation in material removal using fine water jets at extremely high pressures (50,000 psi to 100,000 psi) has been undertaken. This was not the entire reason for this contract from the Bureau of Mines, however. The contract objective is outlined later. IIT Research Institute has done pioneering work in high pressure jet development in the United States.5-8 Similar schemes have been investigated abroad. 9-13 Hydraulic mining of coal at relatively low pressures is successfully being done in the Soviet Union, Japan, Canada, and most recently, in Germany.

Jan 1, 1973

By David W. H. Ellis

This presentation will discuss over 2 dozen past, present and future oils sands projects in Alberta. The very early projects as well as the most recent along with the ones that never got off the ground and the ones in production are all included. For each, the following will be given (where known): owners, location, type (mining/SAGD/refinery), production, capital budget, spent to date, status. Some overall impacts will be discussed.

May 1, 2004

By R. W. Watson, H. D. Peer

"This paper outlines the history of steel linings in the Autogenous Mills, the factors influencing the decision to convert to rubber lining, and the operating and cost experience with the rubber liners to date. INTRODUCTIONSherman Mine is an open pit iron ore mining, concentrating and pelletizing operation located at Temagami, Ontario. The operation employs 392 hourly employees and 81 salaried employees and has an annual capacity of over one million L.T. of high quality iron ore pellets produced from low-grade magnetite ore.The Sherman Mine is a joint venture; 90% owned by Dominion Foundries and Steel Limited (Dofasco) of Hamilton, Ontario, and 10% owned by the Tetapaga Mining Company, a wholly-owned subsidiary of the Cleveland Cliffs Iron Company of Cleveland, Ohio. The operation and management of the mine is by Cliffs of Canada, Limited. Development of the property was started in 1965, with pellet plant production beginning on March 17, 1968. At the present time, the orebodies contain sufficient reserves to sustain operations at current production levels for 30 years. Mining was originally carried out in three orebodies, the North, South, and West pits. The North Pit has been exhausted and mining operations ceased in the spring of 1980. A fourth pit, the East Pit, will be developed during the early 1980's."

Jan 1, 1981

By R. J. McNally

THERE are three primary plant nutrients—nitrogen, phosphorus, and potassium—expressed in any fertilizer compound as percent N, percent P 2 O 5, and percent K 2 O, in that order. This article will be concerned with the first two. The chief source of P 2 O 5 is phosphate rock. As found in the western states phosphate rock is essentially tricalcium phosphate-calcium fluoride (fluor-patite). As such, it is quite water insoluble.

Jan 1, 1957

By M. G. Cheney

Careful estimates indicate that during 1942 new discoveries and extensions in West Central Texas added oil reserves slightly in excess of the eight million barrels produced. Drilling activity fell 40 per cent below 1941 and 82 per cent below the normal drilling activity of the late 1920's. Total production for the district continued its downward trend, now being less than % of the 42.7 million barrels peak in 1921. Rapid revival of activity is not probable under existing conditions, as costs of discovery, development and operations on the average probably now exceed current market price for the oil, the latter having remained constant since the spring of I941. Costs have advanced materially since the third quarter of 1941, when reports to the Tariff Commission indicated a margin of profit of 13.3 per barrel. Physical as well as economic conditions are holding back the amount of drilling in this district. The lenticular sands are not suited to 40-acre spacing regulations. There is no surplus of experienced oil-field labor. To reduce costs, much second-hand material is used for all except the deeper wells.. Price controls have retarded movement of used equipment by prescribing maximum prices that arc too low for the better grade materizl, thus making , owners reluctant to sell. On the other hand, buyers are unwilling to pay ceiling prices asked by sellers for poor material. Seventeen new oil fields and five new gas fields were found during 1942. Extensions and deeper 'drilling brought favorable results in eight older fields. The most significant new developments appear to have been in Coleman, Jones, Shackelford and Taylor Counties. A 5800-ft. completion in Wise County brought this county into the producing column for the first time. None of these new discoveries can he rated above one million barrel reserve on the basis of present development. Probably the most important development was discovery of a deeper pay (Gunsight lime) in the Wimberly field of Jones County, which shows promise of producing over an area of about 1000 acres. Jones and Shackelford Counties still lead the district in total annual production. Discovery of the Reddin pool, north central Taylor County, is credited to geochemical methods, making one success out of five or more wildcats based on such methods. Geophysical surveying increased decidedly during 1942 and returns from these studies are expected during coming years. Most of the wildcatting in the district is still based on surface and subsurface geological structural mapping, study of log data as to distribution of prospective producing reservoirs, and drilling in proximity to previous showings of oil and gas. Geological debate continues as to the proper correlation of the 100 to 300 ft. of gray lime that has produced more than 100 million barrels in the Parks, Brecken-ridge, Curry, Eliasville, Ibex, Pioneer and other important fields of this district. Fossils indicate that this limestone is younger than the Atoka beds of Oklahoma. On a structural basis most geologists include this formation with the Bend but a number of paleontologists believe it is more properly classified with the Strawn.

Jan 1, 1943

By M. G. Cheney

Careful estimates indicate that during 1942 new discoveries and extensions in West Central Texas added oil reserves slightly in excess of the eight million barrels produced. Drilling activity fell 40 per cent below 1941 and 82 per cent below the normal drilling activity of the late 1920's. Total production for the district continued its downward trend, now being less than % of the 42.7 million barrels peak in 1921. Rapid revival of activity is not probable under existing conditions, as costs of discovery, development and operations on the average probably now exceed current market price for the oil, the latter having remained constant since the spring of I941. Costs have advanced materially since the third quarter of 1941, when reports to the Tariff Commission indicated a margin of profit of 13.3 per barrel. Physical as well as economic conditions are holding back the amount of drilling in this district. The lenticular sands are not suited to 40-acre spacing regulations. There is no surplus of experienced oil-field labor. To reduce costs, much second-hand material is used for all except the deeper wells.. Price controls have retarded movement of used equipment by prescribing maximum prices that arc too low for the better grade materizl, thus making , owners reluctant to sell. On the other hand, buyers are unwilling to pay ceiling prices asked by sellers for poor material. Seventeen new oil fields and five new gas fields were found during 1942. Extensions and deeper 'drilling brought favorable results in eight older fields. The most significant new developments appear to have been in Coleman, Jones, Shackelford and Taylor Counties. A 5800-ft. completion in Wise County brought this county into the producing column for the first time. None of these new discoveries can he rated above one million barrel reserve on the basis of present development. Probably the most important development was discovery of a deeper pay (Gunsight lime) in the Wimberly field of Jones County, which shows promise of producing over an area of about 1000 acres. Jones and Shackelford Counties still lead the district in total annual production. Discovery of the Reddin pool, north central Taylor County, is credited to geochemical methods, making one success out of five or more wildcats based on such methods. Geophysical surveying increased decidedly during 1942 and returns from these studies are expected during coming years. Most of the wildcatting in the district is still based on surface and subsurface geological structural mapping, study of log data as to distribution of prospective producing reservoirs, and drilling in proximity to previous showings of oil and gas. Geological debate continues as to the proper correlation of the 100 to 300 ft. of gray lime that has produced more than 100 million barrels in the Parks, Brecken-ridge, Curry, Eliasville, Ibex, Pioneer and other important fields of this district. Fossils indicate that this limestone is younger than the Atoka beds of Oklahoma. On a structural basis most geologists include this formation with the Bend but a number of paleontologists believe it is more properly classified with the Strawn.

Jan 1, 1943

By Christopher C. Jobes, Alan G. Mayton, Timothy J. Matty, Joseph P. DuCarme

Mining injury statistics show that a significant number of back, neck, and head injuries are linked to exposure from vehicle vibration. Use of a suspension seat is a common way to isolate the vehicle operator from the adverse effects of vibration exposure. Thus, researchers at the National Institute for Occupational Safety and Health1 – Pittsburgh Research Laboratory (NIOSH – PRL) performed laboratory studies on four passive and two semi-active seat suspension designs. These are typical of seat suspensions commonly found on large off-road heavy surface mining, construction and agricultural vehicles as either replacement or original equipment manufacturer (OEM) systems. One included a pneumatic (air bladder) spring mechanism. The fifth and sixth suspensions were a NIOSH magnetorheological (MR) semi-active damper design based on the pneumatic (air bladder) and one of the coil spring suspensions above. These suspensions were modified with a commercially available MR damper substituted for the OEM damper. These six seat suspension systems were tested and analyzed, for vertical vibration only, using the ISO 5007 Standard [1]. This paper describes the laboratory vibration tests using a MTS® shaker table and discusses the results obtained for the different suspension designs and highlights the rheonetic technology studied. Implications of the seat suspension designs relative to their capabilities for isolating vehicle operators from vibration exposure are discussed. Results for suspensions 1 through 3 showed frequencies of isolation from 2.1 to 3.0 Hz using the 40-kg (88-lb) mass and from 1.65 Hz to 1.8 Hz using the 80-kg (176-lb) mass. Suspension #4, in tests with only the 80-kg (176-lb) mass, showed an isolation frequency of 3.7 Hz. With the MR damper added to seat suspension #4, the peak transmissibility was lowered from 1.3 to 0.95 and showed a corresponding downward shift in frequency from 2.25 Hz to 1.4 Hz. In fact, the results for suspension #5 (the MR damper added to seat suspension #4), using test #3 conditions of the programmed control algorithm, showed isolation (attenuation of transmitted vibration) throughout the test frequency range from 1.0 to 6.0 Hz.

By D. W. Rich

An environmental management system (EMS) is a key part of a company?s environmental stewardship. Procedures and practices to continually improve environmental performance can provide great benefits in operating the company. Managing site environmental quality data is a key component of this. An environmental data management system (EDMS) is an important element of the EMS for mining and other projects, providing project staff with the information that they need to make decisions that can have a significant impact on public health. Improvements in computers, data communications, and transfer formats have made it much easier to implement an integrated EDMS program for gathering, managing, selecting, and displaying data from the field and the lab. Software now lets users define sampling plans, create files for field data entry, and print Chains of Custody. Laptop and handheld computers facilitate field data entry and may provide automated communication back to the office. Most labs can now create usable electronic data deliverables. QC checks and limit comparisons can be largely automated. The result is organized data that can be efficiently used for reporting, graphing, and mapping, to better understand project issues.

Jan 1, 2009

By A. D. Hughes

A relatively small area in Malaya, about 200 miles long by 40 miles wide, is the most important source of tin in the world. Some tin is recovered in other parts of the peninsula. Of the tin mined, 98 pct is recovered from alluvial deposits. From 1935 to 1941 the average annual world production of tin was 190,000 tons. The average annual production from Malaya during the same period was 62,000 tons or about one third of the total. Other producing countries, in order of importance, were the Netherlands East Indies 34,000 tons, Bolivia 30,000, Belgian Congo, Nigeria, Siam, Burma, China, and a few others with smaller amounts. The serious shortage of tin during the war period was due to the fact that the Japanese were occupying Malaya, Netherlands East Indies, Siam, Burma, and China which, together, formerly were producing 65 pct of the world supply.

Jan 1, 1949

By E. A. Sarver

The Fe(II) regeneration process is an important aspect of Alternate Anode Reaction Technology (AART) for copper electrowinning (EW). In AART, Fe(II) is oxidized to Fe(III) at the anode during EW, and it must be regenerated to maintain recyclable electrolytes. Regeneration is achieved via Fe(III) reduction by SO2(aq), and the reaction is catalyzed by activated carbon particles. To better understand this process, a kinetic model was developed and experimentally validated for the Fe(II) regeneration in the current work. The investigation focused on the primary reaction mechanism and the reaction rate dependence on four variables: carbon particle size, flow rate, initial Fe(III) concentration and initial SO2 concentration. The Fe(II) regeneration reaction is mass-transfer controlled in the presence of activated carbon. Carbon particle size and initial Fe(III) are the most influential factors under the conditions tested. Initial SO2 concentration is insignificant to the reaction rate.

Jan 1, 2007

S. LE FEVRE, Forest Glen, N. Y. (communication to the Secretary*).¬F. L. Nason thinks I could not have studied Mr. Witherbee's paper and doubts the arithmetic used, but in his discussion arrives at practically the same conclusion. He says 10 ft. thickness of ore over a square mile should give 27,878,400 tons, allowing 10 cu. ft. per ton of ore. This is correct, but if he reads carefully he will see that this depth of ore was figured as covering one-tenth of the surface, which reduces the figures to those used by Mr. Nason. I did not say, however, that there were 2,300,000,000 tons of ore in New Jersey, but that applying the same method of computation as used by Mr. Nason, to the area of the iron ore-bearing gneisses in New Jersey, we would get a total of 2,300,000,000. I did say, "In this area are located 366 magnetite mines that have been worked more or less. These lenses may easily be capable of producing (on an average) 1,000,000 tons each, and there are probably double the number listed not opened up." Thus my estimate for New Jersey, as far as any was made, would be: Probable ore 366,000,000 Possible ore in addition 732,000,000 1,098,000,000 Mr. Nason's final conclusion of his personal estimate was one-half of what he erroneously read to be the estimate given in the paper, or half of 2,300,000,000, which equals 1,150,000,000. So the two estimates seem to differ less than 5 per cent., and we have the two sister States of New York and New Jersey on an equal footing of productive possibilities in magnetic ore.

Jan 6, 1917

By M. E. Wadsworth, R. C. Peterson, W. M. Fassell

The temperature and pressure dependence of the reaction of tantalum in oxygen were investigated from 500° to 1000°C at pressures from 10 mm Hg to 600 psi total oxygen pressure. Tantalum was found to oxidize linearly under the above conditions. Three distinct regions of temperature dependence were found with different energies of activation. From 500° to 600°C the rate of oxidation of tantalum was found to be essentially independent of the oxygen pressure at the pressure investigated. The oxidation rate increases rapidly with an increase in pressure from 600' to 800°C. The dependence of the oxidation rate on the bulk concentration may be expressed by V = k'?, where k' is the specific rate constant and ?=k1Co2/(l + K1Co2), where k, is the equilibrium constant for the adsorption of oxygen on tantalum. ONLY a limited amount of data has been presented in the literature on the oxidation behavior of tantalum metal. Some values of its oxidation rate were reported in the Corroston Handbook' and by McAdams and Geil.' The first extensive investigation of tantalum was the work of Gulbransen and Andrews." They determined the reaction rates of tantalum in O2 and N2. Their results indicate that this metal follows the parabolic law in the temperature range of 250" to 450°C in O2 at pressures of 7.6 cm Hg with an activation energy of 27,400 cal per mol. In nitrogen, the metal follows the parabolic law from 500" to 800°C at 7.6 cm pressure. All experimental determinations were of 2 hr or less duration and deviations from the parabolic rate conceivably could occur at longer times. A spectrophotometric study of the oxidation of tantalum by Waber, Sturdy, Wise, and Tipton' indicated good agreement between this method and the microbalance technique. The experiments were conducted in air from 220" to 350°C. The metal was found to follow the logarithmic law up to 320°C and the parabolic law at higher temperatures. The activation energies in the logarithmic region were reported as 12.57 kcal per mol and 12.0 kcal per mol, respectively, for the microgravimetric and spectrophotometric methods. In the parabolic region the activation energy was found to be 27.2 kcal per mol, in good agreement with the value of Gulbransen and Andrews." The present paper is concerned with the behavior of tantalum from 500" to 1000°C in oxygen at pressures ranging from 1/2 to 40.8 atm pressure. Earlier preliminary data by McKewan5,6 indicated the following facts concerning the behavior of tantalum: 1—At temperatures from 500" to 600°C, the metal followed the linear law. 2—At 575°C the rate of oxidation was found to increase with O2 pressure. 3—The Arrhenius plot in this temperature region was nonlinear. The nonlinearity of the Arrhenius plot was indicative of a more complex behavior than originally suspected for this metal.

Jan 1, 1955

By D J. Brake

The importance of mine ventilation to health and safety in both coal and metalliferous mines has been long recognised. The primary and secondary ventilation systems in most metalliferous mines incur 50 per cent or more of the total mine electrical power consumption and frequently about 10 per cent of total underground mine operating costs. The requirements for ventilation-related horizontal and vertical development, fans and cooling have a significant impact on mine capital costs and also on mine schedules and start-up times and hence cash flows. There are increasing pressures on regulators and miners to reduce airborne contaminants such as diesel particulatematter, nitrogen dioxide and heat (wet bulb temperatures), and significant pressures to reducegreenhouse gases such as fugitive methane emissions from coalmines and the carbon dioxide footprint of both coal and metalliferous mines. Many previously Australian miners are now globaloperators and have extensive overseas mining operations where local ventilation standards and expertise may not be consistent with Australian practices. The role of the site ventilation officer is also changing with strict new requirements for the statutory position being introduced into Queensland metalliferous mines and the potential for this to become more widespread. Recent regulator and parliamentary review committees have identified systematic shortcomings in mine ventilation compliance, and statutory certificates in both Queensland and NSW now require continuing professional development to maintain currency. Public and investor support for mining are also increasingly contingent on safe, healthy and environmentally responsible practices and the standards for these are frequently tightening. Good ventilation design and operating practices that are consistently well executed therefore contribute significantly not only to a safe and healthy mine but also to a productive and cost-effective operation and the ongoing social licence to operate. There are a variety of ways of providing technical design and oversight into a mine’s ventilation systems; this paper explores some current trends in ventilation standards and statutory requirements, as well as ways to support and develop mine ventilation staff for both domestic and international operations and also the emerging senior technical roles of Group/Principal/Corporate mine ventilation engineer.

Oct 12, 2022

By Lei Wang, Qi Zheng, Xiao-kui Che

"The wastewater emitted by gold chemical industry contained vast of different heavy metal ion, such as Zn, Cu and Ni etc. Among them Zn is the main ion in the waste water which causes the serious environment pollution. A method of preparing a kind of resin which is used for the removal of Zn by magnetic adsorbent was developed and was applied in practice. This adsorbent is a chitosan made of a kind of Fe3O4-chitosan modified by epichlorohydrin. The adsorption capacity of the absorbent and it was concluded that under the laboratory conditions, the maximum adsorbing capacity of this adsorbent could be 287.58 mg/g. The absorbent was also applied in the wastewater emitted by a gold industry in Shandong province. Its performance was tested and the result showed that the concentration of Zn ion in the wastewater was reduced from 0.58 mg/L to 0.0174 mg/L. What is more, the adsorption rate could be more than 97% when the dosage was 100L/m3 after adsorbing for 1h. KEYWORDS Selective, preparation, laboratory experiments, industry experiment, comparation INTRODUCTION Currently, most gold chemistry use cyanide to leach gold ore. Many different metals participate to this reaction besides the gold ion in this processing, so that the composition of the water is very complex. The waste water emitted by gold chemistry industry contains large amount of heavy metals. Definitely, if it was discharged without any treatment, the water would threaten the environment. The recuperation of any ion in the water would mitigate the pollution. Ion exchange resin, which is an effective material to do the water treatment with low cost, became widely applicated in this field [Yu-jiao Wang,2013]. Different kinds of resin were developed and the influence factors such as pH, adsorption properties and selectivity for different ions were investigated [CA Cruz et al,2018; PawanKumar et al.2016; Y Zhang, et al,2010; and ShengingSun, Aiqin Wang, 2006;]. The waste water mentioned in this article has a high Zn concentration, so a magic resin for Zn adsorption selectively we designed was used to manage this water. And the recovery of Zn could not only contribute to pollution abatement but also a best way to settle a dispute to the short of Zn resource. So the article mainly describes the preparation and the application of a kind of magnetic adsorbent used for the removal of Zn both in laboratory and industry. The aim of this article is to compare the effect of this resin in industry and laboratory?"

Jan 1, 2018

By David J. Hoadley

This report describes the development and underground operation of a semi-automatic, raise climber, Man and Supply Hoist System designed for stope access in underground metal and nonmetal mines. Demonstrated capabilities of the system include a 4000-lb payload capacity, control from the traveling cage and from up to five remote stations, operating in vertical or inclined raises 5 ft in diameter and up to 300 ft in length and a travel speed of 50 ft/min. The 'system has the capability of operating in crooked raises because the conveyance climbs two stationary wire ropes suspended down the raise. The drive unit is electrically powered with power and control signals supplied to the drive unit through an armored cable also suspended down the raise. The system has been designed for portability, ease of installation and minimum raise development. The system can be installed by two men in five shifts. The hoist has been demonstrated successfully in two underground applications. The first demonstration was in a 5-ft diam, 60 deg inclined raise over a 2-month period. The second demonstration utilized a vertical 5-ft diam borehole to access a blast-hole stoping area. The system successfully provided two shift-a-day service over a 7-month duration demonstration. This report provides a detailed description of the hoist design and its demonstrated performance in two mine applications.

Jan 1, 1981

By W. L. Falconer

"IntroductionThe very recent emphasis on the importance of the northern portions of the Alberta basin as a prospective oil province has led the oil companies northward into new and undeveloped territory. Northern Alberta is a land of continuous forest, covering a plains-type topography. The plains are only occasionally broken by sharp, broad river valleys. Tributary streams head up quickly and very soon lose themselves in large undrained areas. It is these pseudo-swamps that cause most of the troubles and headaches of the oil explorer.The rivers have served as the main transportation arteries since people first ventured into this area. The bush is being pushed back, but the advance is slow and there is very little more than trappers' trails beyond a few miles from the Northern Alberta Railway lines and the recently built Grimshaw or McKenzie Highway. Indeed, bush and muskeg flank many miles of the railways and roads within as close a distance as fifty miles of Edmonton. Northern Alberta is pioneer country in the truest sense of the word, and our greatest problems derive from this fact. In all pioneer areas, the first requirement is the development of access roads, and before active oil exploraton can get down to the job at hand these roads and trails must be an accomplished fact. There are two factors in Northern Alberta which offer discouragement to the oil explorer: the first and greatest stumbling block is presented by the numerous muskegs, large and small; the second is the fact that road building uses up so much of reservation time. Of course, the second is aggravated by, and a direct result of, the first. So we come back to the main problem facing the development of the north - the muskegs."

Jan 1, 1950

By David C. Minton

This paper describes in detail the cost of equipping and developing the Golden Belt mine, Yavapai County, Ariz. These costs should be typical of the average small gold mine in central Arizona which has been equipped with used machinery a, a minimum of capital expenditure. The conditions of remoteness, transportation, water, and power supply are about average for properties in the Bradshaw fountains and that vicinity. There are several mines in the district in the process of development and several dormant properties that might be opened in the future. The Golden Belt group of claims was taken over by the present management in May, 1931. Although some active development has been carried on in recent years, resumption of work at the old property required entire rehabilitation of the equipment and camp. As the water level had not been reached, there was no problem of dewatering. In the presentation of costs in this paper an evaluation of the cost of equipment and development work as taken over by the Golden Belt Mines, Inc., has been made. Enact data, however, on previous exploration and construction costs are lacking. The total cost of equipping and developing the mine to its present stage has been obtained by adding the disbursements of the present management to the above-mentioned evaluation. These costs do not include the cost of replacing camp, equipment destroyed by fires, of unsuccessful milling experiments, management, or obsolete equipment on the property.

Jan 1, 1933

Please note all Proceedings of the Institute were taken verbatim by stenotypists from Hyatt & Associates of Denver and editing has been minimal. MR. MORTENSEN: On behalf of the Rocky Mountain Coal Mining Institute, I take great plea¬sure in saying good morning to you at Vail. With a few clouds in the sky, at least we won't get sunburned. We won't have to worry about our kids in the swimming pool, perhaps. It is delightful for me to have been able to have represented the Rocky Mountain Coal Mining Institute for the year 1982-1983. This has been our 71st year and this is our 79th meeting. In recognizing the attendance here, that dinner we had last night, and some of our entertainment must have gotten to some of us, or it is a little early. But I'm sure as the day goes on, and with the speakers outlined, it will be very beneficial for those who do attend. We do appreciate your attendance. I'd first like to make an introduction of our head table. Doris Finnie, she is our executive secretary. As most of you are aware, Gussie Whiteside retired as secretary. This will be the first time since the Institute started that there has not been a Whiteside present at one of our conventions. I'm sure Gussie would appreciate any calls or letters that any of you would care to make to her. Doris, I might add, has been a great help to me and all of the people who have been working on the program for the Institute this past year. There's been lots of reorganization and we are very pleased with Doris's ability to take hold from Gussie without any waves. Much credit must be given to you Doris for this and we do appreciate the help you have given us and believe me she has kept us out of trouble. Next, we have Art Neill. He is our vice president of the Institute from Montana and he also works with Western Energy Company. We appreciate the help that all of these session leaders and chairmen give to us. We have other names on the head table, but they will fill in as the morning goes on, so we won't bother you with any of those at this time. To set the stage for business, first I would like to call on Doris for a motion to approve the minutes of last year. MS. FINNIE: Thank you, Vernal. Mr. President, I suggest that the reading of the minutes be dispensed with and that the members refer to pages 9 through 80 of the Proceedings for the 78th regular meeting of RMCMI, as published MR. MORTENSEN: Thank you, Doris. Do we have a motion to so approve? MR. LINVILLE: I so move. MR. MORTENSEN: Loren Linville so approved. Do we have a second? MR. GARR: Second. MR. MORTENSEN: All in favor say aye. (Audience responded affirmatively.) MR. MORTENSEN: Those opposed? Hearing none, the motion is carried. I'm sure glad we didn't have to read those 80 pages. Is Doug Hammer in the audience? He was going to give us a list of new members of the Coal Institute and ask for your approval. But because of his absence, the names will be listed so that you can read them at a later date, I will entertain a motion that we approve the new members who have joined the Institute. Do I so have a motion? MR. BERNSTROM: I would make that motion. MR. GARR: I second. MR. MORTENSEN: Do we have any questions? All in favor¬ (Audience responded affirmatively.) MR. MORTENSEN: Any opposed? Hearing none, the motion is carried. Next, we'd like to proceeed with our Nominating committee report from the chairman, George Nugent, and the election of next year's officers. George, would you please take the stand? MR. NUGENT: Mr. President, and members of the Institute, your Nominating committee consists of five past presidents of the Rocky Mountain Coal Mining Institute. From Colorado Roy Coulson; from New Mexico, Bob Wilson; from Utah, Bob

Jan 1, 1983

By N. Jaffee, J. E. Dorn

An activation energy of 27,400 5 1000 cal per mole was obtained for the creep of poly crystaLline aluminum over the temperature range of 273° to 350°K, at strains varying from 0.003 to 0.230. Stresses varied fronz 2250 to 6000 psi, strain rates from 0.1145 x 10-5 to 29.5 x 10~s min.-1. A strain temperature-compensated time correlatzon was oblained indicating that the structure was depedent solely upon the strain at a given stress; X-ray diffraction analyses and tensile tests on precrept specimens verified this. PREVIOUS investigations1 have revealed that the apparent activation energies for creep of high-purity polycrystalline aluminum are insensitive to the applied stress, strain, and strain rate. On the other hand, the apparent activation energy is dependent on the temperature1,2 as shown by the data reproduced in Fig. 1. Each plateau of this curve is associated with a unique rate-controlling dislocation mechanism for thermally activated creep. It is now very well-established that over the high-temperature range, where the activation energy is about 35,500 cal per mole, the creep rate is controlled by the dislocation climb mechanism. 3 Over the intermediate range of temperatures, from about 260° to 370°K, another unique activation energy, namely 28,000 cal per mole, is obtained. Current evidence strongly supports the contention that cross slip is the rate controlling mechanism for creep in this case: 1) Crystal recovery can occur by a number of mechanisms prominent among which are climb and cross slip. Astrom,4 using the Borelius micro-calorimeter, reported rapid crystal recovery of cold-worked polycrystalline A1 at 340° to 370°K giving an activation energy of 28,000 cal per mole and additional recovery at 455° to 478°K giving an activation energy of 3 6,000 cal per mole. Whereas the latter recovery process was clearly associated with the dislocation climb mechanism, the former, 28,000 cal per mole process could have arisen as a result of the cross-slip mechanism. 2) Single crystals of high-purity A1 favorably oriented for octahedral glide exhibit an activation energy for creep of about 3400 cal per mole over the range from 0° to 400°K and that of about 28,O:O cal per mole over the range from 600° to 775°K . Whereas the lower activation energy process is accompanied by the development of sharp slip-band traces, the 28,000 cal per mole process was uniquely characterized by extensive cross slip. 3) Theoretical calculations by Seeger and schoeck6 suggest an apparent activation energy for cross slip in A1 of about 24,000 cal per mole and another theoretical estimate by Friedel 7 gives the observed 28,000 cal per mole as the theoretical activation energy. It is therefore consistent with this evidence to, at least tentatively, ascribe the 28,000 cal per mole creep process in A1 to the operation of cross slip as the rate controlling mechanism. Although creep has been rather well-explored in the dislocation climb range, very little, excepting perhaps the activation energy, is known about creep in the cross slip range. This investigation was undertaken, therefore, to reconfirm the activation energy for creep in polycrystalline A1 in the intermediate temperature range and to study the strain-time relationship for creep at a constant stress in the cross slip region. EXPERIMENTAL PROCEDURE AND TECHNIQUE The three types of high-purity A1 alloy specimens described in Table I were used in this investigation. Specimens were milled from 0.100 in. thick cold-rolled sheets with their tensile axes in the rolling direction following which they were given a recrys-tallization and grain growth heat treatment at temperatures well above those which were subsequently employed in the creep tests.

Jan 1, 1962

By Thomas R. Kuesel

Just south of the L'Enfant Station in Seventh Street, the WMATA system splits into two branches, each comprising twin single-track soft ground tunnels. Immediately at the beginning of the section, Interstate Route 95 crosses transversely over the alignment in open cut, removing most of the cover over the tunnels. Seventh Street spans I-95 on a bridge whose abutments and pier also cross transversely over the four tunnels, with their footings as little as 7 feet above the tunnel crown (Figure 1). Soil investigations revealed that the tunnels would have to be driven through mixed face, with a clay invert and a waterlogged sand crown. Thus, there was a good chance that the roof would fall in, leaving 1-95 and the Seventh Street Bridge in a crater. Since there was no roof that could be counted on, these were figuratively (and potentially truly) Washington Metro's Topless Tunnels (Figures 2 and 3). DESIGN ALTERNATIVES Faced with this situation, the designers considered several options, including temporary detours that would permit demolition of the bridge and building tunnels under the 1-95 Freeway by cut-and-cover methods. They also investigated structural underpinning of the bridge and freeway pavement, and strengthening the bridge abutments and center pier by post-tensioning to enable them to span over any subsidence trough.

Jan 1, 1976