Search Documents

By N Kado, T Iwama, R Inoue, S Ueda

Steelmaking slags are usually used as roadbed and civil engineering materials. However, the expansion phenomenon, which is caused by the volume expansion during hydration of free CaO and free MgO contained in steelmaking slag, is indispensable. Since the hydration of free MgO in steelmaking slag is much slower than that of free CaO, it is qualitatively considered that free MgO contributes to the hydration expansion of steelmaking slag over a long period of time. Similar to free CaO, free MgO consists of undissolved MgO and crystallised MgO in steelmaking slag. The latter precipitates during slag cooling. When divalent metal oxides (FeO, MnO, CaO) are dissolved in the crystallised MgO to form a MgO-based solid solution, it is expected to inhibit the hydration reaction similar to precipitated CaO. From the previous hydration test of Magnesioferrite, which was calcined after mixing MgO and Fe2O3 reagents, it was found that the higher the Fe2O3 concentration, the slower the hydration reaction progressed. In this study, by clarifying the influence of calcination conditions of MgO-FeO and MgO-FeO-MnO solid solutions, which were prepared by the calcination of mixture of MgO, FeO and MnO reagents, on their hydration reactivity, the effect of composition and thermal treatment on the formation of free MgO that is not hydrated (or easily hydrated) were discussed. To investigate the influence of MgO grain size, coarse MgO particles, which were obtained by crushing MgO crucible, were also used for heat treatment. With increasing the amount of FeO and MnO in the MgO-FeO-MnO solid solution, the hydration reaction became more suppressed. The expansion suppression effect was higher with solid-solved FeO than with solidsolved MnO. When the calcination temperature of the MgO-FeO solid solution was increased, the Fe3+/Fe2+ concentration ratio increased, resulting in a higher hydration rate.

Jun 19, 2024

By Thomas C. Denton

In 1965 Africa maintained its position as a region of the world essential to advanced non-Communist nations for supply of vital metals and minerals. The position stemmed from the fact that Africa produced in large quantity a number of key minerals of which either or both resources and production capacity elsewhere did not approach the needs of the free world. The Republic of South Africa alone contributed more than three quarters of the gold mined in the entire non-Communist world besides an estimated 60 percent of metals of the platinum group and the entire new supply of amosite asbestos, and Africa as a whole was nearly the non-Communist world's only source of gem and industrial diamond. Africa also accounted for 83 percent of non-Communist world cobalt production. Besides these massive contributions, Africa in 1965 provided 50 percent or more of the new supply from non-Communist countries of the following mineral commodities: Lithium minerals, corundum, manganese ore: and chromite, and over 20 percent of new supply from non-Communist countries of columbium-tantalum concentrates, antimony, beryl, vanadium, phosphate rock, and copper. Africa also accounted for 18 percent of the non-Communist world's output of uranium, 14 percent of its tin, 11 percent of its lead, 9 percent of its zinc, and 8.9 percent of its crude oil output. With respect to chromite, at yearend Africa's reserves of the mineral were far larger than those of all other non-Communist regions combined. This probably also held true for manganese ore. In the case of crude oil, the fact that Africa's share of non-Communist world output was 1.6 percentage points greater than in 1964 was significant, particularly inasmuch as the output rate was continuing to increase at yearend.

Jan 1, 1967

Effective gas management in coal mines, as well as proper ventilation design, is very important for maintaining the safety of underground coal miners. Advances in numerical modeling techniques have enabled evaluations of the coal mining environment using advanced grid designs and computed gas distributions through detailed mathematical models. These models help engineers to see the unseen areas of the mine through visualization of the data and ultimately help improve worker safety. This paper summarizes the modeling efforts conducted by NIOSH in the U.S. and CSIRO in Australia to address various gas management issues encountered in longwall mines. The modeling studies involved two of the most widely used grid-based techniques, namely computational fluid dynamics (CFD) and numerical reservoir modeling. This paper discusses the application of these techniques for gob inertization and gas control for spontaneous combustion, pre-mining degasification of coalbeds, gob gas venthole design and performance evaluation in longwalls, and gas management during development mining.

Jan 1, 2009

By Bora Derin, Onuralp Yucel, M. Seref Sonmez, Murat Alkan

"Latest stage in the production of boron carbide by metallothermic methods using magnesium was the leaching process. Boron carbide particles obtained by self-propagating high temperature synthesis contained several impurities such as magnesium oxide and magnesium borates after the metallothermic reactions. Removal of such contaminates by hydrometallurgical methods required to produce high purity boron carbide. Leaching by concentrated hydrochloric acid solutions resulted in the production of pure boron carbide together with high magnesium and boron containing solutions. Removal of such ions from the spent liquor was the necessity to have dischargeable solution. In this study, precipitation of magnesium and boron compounds from relevant chloride containing spent liquors and the production of saleable products was aimed. The effects of chemical reagents, pH of the solution on the precipitation efficiency of magnesium and boron compounds were investigated in the study. Chemical analysis and the characterisationof solid phases by using x-ray diffraction analysis were the latest stage.Introduction A variety of advanced ceramics, inter-metallic, organic and inorganic compounds, oxygen free single crystals, and polymers can be synthesized by using different SHS techniques [1, 2, 3]. In the SHS process, after initiation, reaction becomes self-sustaining and propagates in the reactant mixture. A high amount of heat which is generated during the process accelerates the reaction rate and thus it makes the process highly productive and economically feasible for different production scales. After the SHS process obtained powder mixture needs to reacted with acidic solutions to purify the product. In this case B2O3 was reacted together with C and Mg to synthesis fine B4C powder resulted in the production of MgO as well according to the Eq. 1 and then MgO was removed from the mixture by leaching with the concentrated HCl solution as shown in Eq. 2, respectively [4, 5]."

Jan 1, 2008

By Aline Silva Magalhães

Nas últimas décadas a crescente demanda por carros mais seguros, econômicos e menos poluentes exigiram das montadoras, siderúrgicas e comunidade científica investimentos na pesquisa e no desenvolvimento de novos materiais, tais como os aços avançados de alta resistência. Dentro deste contexto, neste trabalho foi realizada a análise da microestrutura e das propriedades mecânicas de um aço bifásico na condição inicial e submetido a tratamentos térmicos com aquecimento na região intercrítica e resfriamento brusco. Foram analisadas a proporção dos constituintes na microestrutura e as propriedades mecânicas por meio de microscopia óptica e eletrônica de varredura, de difração de raios X, dureza e de tração. Observou-se, em geral, que o aumento da temperatura intercrítica levou a uma elevação da fração de martensita e, consequentemente, influenciou de forma a aumentar os valores de dureza, resistência mecânica e diminuir a ductilidade.

Aug 16, 2017

By A. Korchevskiy

While Russia continues to be a worldwide leader in asbestos production, the environmental and health status around Russian asbestos mines is not well known and understood, internationally. A literature review was performed to evaluate the potential impact of Russian mining operations on mesothelioma incidence rates in the Ural region where the majority of the asbestos deposits are located. Asbestos that has been mined in this region includes chrysotile, crocidolite, and anthophyllite forms. The Nicholson-Peto (1986) model was applied to published exposure data and mesothelioma mortality statistics in different cities and villages of the Ural region to estimate mesothelioma potency factors (KM) for the various associated fiber types. It was demonstrated that mesothelioma potency factors, as determined by Berman and Crump (2008), could be used to predict mesothelioma risks of non-occupationally exposed individuals in locations where either pure chrysotile, or both crocidolite and chrysotile, are mined and milled. A mesothelioma potency factor was calculated for anthophyllite that appeared to be higher than expected based on previously published studies. The highest incidence of mesothelioma was identified in a community close to a crocidolite mine. The study confirms the validity of utilizing current risk models for non-occupationally exposed populations near asbestos mining activities where asbestos exposures are relatively low and provides methods of characterizing mesothelioma risk in the former Soviet republics (FSRs).

Feb 27, 2013

By Mariana Carla Mendes Rodrigues

Os aços ferramenta para trabalho a frio são utilizados em diversas aplicações em decorrência de propriedades como elevada estabilidade dimensional, alta resistência ao desgaste e elevada temperabilidade. Tais características estão diretamente associadas à microestrutura do material, isto é, à quantidade, à distribuição, ao tipo e à morfologia dos carbonetos presentes e à quantidade de martensita revenida e austenita retida. Neste contexto, no presente trabalho foram caracterizados mecanicamente e microestruturalmente quatro aços ferramenta para trabalho a frio empregados na fabricação de cilindros de laminação a frio. Para isso, amostras foram retiradas dos próprios cilindros e foram realizadas análises de dureza, microscopia óptica, microscopia eletrônica de varredura, espectroscopia por energia dispersiva e espectroscopia de emissão atômica por plasma. De acordo com resultados, uma comparação entre as propriedades dos aços foi conduzida visando concluir qual deles é o mais adequado para a referida aplicação.

Aug 16, 2017

This publication contains four papers presented at a seminar on mine subsidence control held in Pittsburgh, PA, on September 19, 1985. The seminar was designed to keep the mineral industry informed of new technology developed by the Bureau of Mines that permits reliable and accurate prediction of mine subsidence. The papers describe actual field studies undertaken by the Bureau to monitor surface subsidence over longwall panels. Topics discussed include the efects of subsidence on water table levels, the development of subsidence pre calculation methodology suitable for use with the specific lithological conditions of the Pittsburgh coalbed, an engineering comparison of technologies used in surveying for longwall mine subsidence, and a comparison of the process of subsidence over two different longwall panels.

Jan 1, 1985

By Jasmin Raymond

Ground source heat pumps are used to heat or cool building and heat water supply. Such heat pumps use the earth as a heat source or sink to efficiently provide or store thermal energy. For example, a ground source heat pump typically requires less then a third of the electric or fossil fuel energy of a conventional heater. Ground source heat pumps could therefore help reduce the energy consumption of active mines where low-grade geothermal resources are abundant. In most heat pumps, water or a water-antifreeze mixture having a temperature ranging from -6.5 to 43.5 °C is circulated through a heat exchanger at a rate of 0.000033 to 0.000067 m3/s (2 to 4 L/min) for each kilowatt of heating/cooling capacity. The groundwater that is continuously pumped to drain mines could be used to operate heat pumps. Water feeding a heat pump can alternatively circulate in a close loop network of pipes buried underground or installed in a surface water body. Retention water ponds, tailings and waste dumps commonly found at active mine sites could provide excellent environments to install the close loop system. Further research will help take advantage of the unexploited geothermal resources associated with actives mines.

May 1, 2007

By Oscar Delgado Venero

Dado el alto potencial económico de los metales preciosos que genera Centromin Perú, el yacimiento minero elaboró un programa de investigación para la recuperación del oro y la plata, a partir de minerales marginales, relaves y productos intermedios de fundición. Durante el desarrollo de este programa, se utilizó el proceso de lixiviación en botaderos la extracción de plata para la extracción de los minerales piríticos de Cerro de Pasco, obteniendo resultados óptimos. Por tal motivo, el presente texto señala el proceso de lixiviación en botaderos que Centromin decide implementar en una planta industrial, utilizando como lixiviante el sistema de Nac1-H2 SO4 y la chatarra de fierro como agente de cementación.

Nov 24, 1986

By Cristiano José Scheuer

The effect of low-temperature plasma carburizing treatment on the micro-abrasive wear resistance of AISI 420 steel was investigated by mean of a CSM Calowear ball-cratering equipment. Carburized samples were treated at temperatures of 350, 400, 450 and 500°C for a fixed time of 12 h, using a gas mixture containing 99.5% (80% H2+20% Ar)+0.5% CH4. Micro-scale abrasive wear tests were conducted with a 25.4 mm AISI 420 steel sphere, using an abrasive suspension of alumina (Al2O3) with particle size of 1 ?m (abrasive concentration of 0.11 g/cm³). The contact normal force, abrasive flow and ball rotation speed were fixed at: 0.5 N, 0,2 drop/s, and 120 rpm. The wear craters were analyzed using a confocal laser microscope, Olympus OLS 3000. The wear analyses were performed for test times of: 30, 60, 90, 120, 180, 360, 540, 720 and 900 s (equivalent sliding distance: 0.84, 1.68, 2.52, 3.36, 5.04, 10.09, 15.14, 20.19 and 25.23 m, respectively). The results indicate that the wear coefficient in the outer layer and in the diffusion layer are different, being lower in the latter. It was also verified that the wear coefficient on the outer layer region decreases with increasing treatment temperature in the range of 350 to 450 °C, and increase again for 500ºC. The diffusion layer wear coefficient is similar for all the carburized samples. Finally, for all studied conditions, the analysis of the wear craters surface indicates the occurrence of grooving and micro-rolling abrasion wear modes.

Aug 8, 2018

By Garry M. Johnston, Matthew L. Sutcliffe, Nicholas J. Welham

"The predominant current processes for the treatment of oxidized copper–cobalt ores use a reductive acid leach to bring the desired metals into solution. However, the indiscriminate nature of acid leaching results in a solution, akin to a metal soup, containing not only the Cu and Co but also an extensive suite of other metals. These other metals, notably Fe, Mn, Al, Ca, Mg and Si, all have to be eliminated from solution before the copper and cobalt can be recovered. Generally precipitation processes are used, but these tend to result in significant losses of copper and/or more usually cobalt from solution, leading to reduced recoveries. The AmmLeach® process uses ammonia-based chemistry to selectively leach the target metals, leaving the rest behind in the leach residue. This approach eliminates any need to clean the solution of unwanted metals and the consequent metal losses. After solid–liquid separation, the leach solution is immediately subjected to separation and concentration of the copper and cobalt using solvent extraction and electrowinning. INTRODUCTION The Copper Belt extends through the northern part of Zambia and the southern province of Katanga in the Democratic Republic of Congo (DRC) and contains the richest and highest grade deposits of copper and cobalt remaining in the world. Whilst there are a number of mines that produce sulphide concentrates, using froth flotation, the largest deposits are those where near-surface sulphides have been weathered over time to form oxides. The oxides cannot be concentrated by conventional physical means to give high recoveries. Despite this, a number of dense medium separation plants have been installed and used to produce a higher grade concentrate which is typically exported (while the rejects, typically 2 to 3% Cu are stockpiled for treatment at a later date). These plants generally have low recoveries and can only be used on the dwindling supply of high grade materials. In exporting the concentrate, little value adding is undertaken within the country, thus greatly reducing the economic benefits to the country. Recent changes to the regulations in the DRC will effectively ban the export of low value ores, concentrates and intermediates in favour of high value metals. This will necessitate mines to install new processing circuits in order to comply with these regulations. The head grade of ores currently being treated in the DRC is slowly decreasing as the extremely high grade materials are being selectively mined out. In many cases, the removal of a small volume of high grade materials leaves a much larger volume of economically marginal ore behind. This is due to a desire for short-term profits overtaking long-term prosperity. The remaining ore, which in many cases is still of relatively high value by world class standards, is likely to be only treatable by low cost heap leaching. There are some initial trials of heap leaching within the DRC, but implementation at a large scale has yet to be adopted."

Jan 1, 2015

By C. K. Donoho

SILICON is used in almost all commercial steels; up to about 0.20 pct in killed wrought steels and 0.50 pct in steel castings. Above about 0.50 pct in wrought steels and 0.70 pct in cast steels, silicon is considered an alloy. As an alloy, silicon is useful for several purposes: (I) for its effect on magnetic properties of parts for electrical apparatus; (2) for increasing the yield strength of carbon and low-alloy steels without too much sacrifice of ductility and weldability; (3) for adding hardness and toughness to spring and chisel steels; (4) for adding resistance to scaling and carburization to heat-resistant steels; and (5) for its graphitizing effect in graphitic steels. In acid electric steels for casting we are principally interested in the effect listed second; i.e., increase of strength with minimum sacrifice of ductility.

Jan 1, 1947

By A. Tekin

In almost all branches of industry, machinery and equipment in operation cause vibration. Some sources of vibration affect only the operator’s hands, fingers, and arms, while others have adverse effects on the entire -body. Various types and numbers of machines are utilized in the mining sector, and operators with them are exposed to mechanical vibrations caused by the mining machinery they use. A field study was conducted to evaluate the vibration risks to the operators using mining machines in open pit mines. Vibration levels and whole-body vibration (WBV) measurements using various types brands, and models of construction equipment were evaluated in three different mines in the west of Turkey and compared to the the criteria specified in the EU 2002/44/EC directive and ISO 2631-1 (1997) standards. The results showed that operators using mining machinery for 8 hours were exposed to WBV levels below the EU limit (1.15 m/s2), while 44% of these operators were exposed to levels above the EU action limit (0.5 m/s2). Measurement data collected from the working environment and the recommended improvements that need to be made to reduce WBV exposures are presented.

May 2, 2022

By Richard A. Cubeta

Precast concrete segments have been used in sanitary sewer tunnel design for decades. Federal mandates (reduction in heavy metals and I & I), and system design changes (increased retention times) and other factors have exacerbated corrosion problems. In an effort to combat the ever-growing effect of microbiologically induced corrosion, owners, engineers, and designers have been specifying thin-film lining systems to protect precast concrete segments. These systems have compatibility and installation issues. Chemical additives or calcareous aggregates have been utilized in precast concrete, but have only proven to retard the rate of corrosion and do not eradicate the problem. Solid cast polymer segments are stronger than precast concrete, do not require linings or coatings, are impervious to ground water infiltration, and, above all, are inherently corrosion resistant through and through.

Jan 1, 2008

By Bellairs P, Stewart JC

On 20 December 1983 at 8.40am blast- hole 57 of Blast RN177 prematurely detonated follwed by a violent deflagration of blast- hole 59 at 10.40am. The blastholes were 380mm diameter drilled in black pyritic Mt McRae shale. The blastholes were loaded with ANFO and primed. Blasthole 57 was stemmed and blasthole 59 was not. A poss- ible mechanism which could lead to such a detonation is described. preliminary tests showed the top 5m of a bench had the highest temperature which could not be influenced by a range of treat -ments. Small scale laboratory tests show- ed that zinc oxide (ZnO) and magnesium carbonate (Mg2CO3) inhibited the reaction. A series of tests using AN with and without inhibitors loaded into the collars of blast -holes drilled in the top 6m of the bench and unstemmed is described. An analysis of the time to reaction of the holes loaded with AN against temperature shows that the decomposition of the AN in contact with the black pyritic shale is probably a sulphuric acid catalysed react- ion. All the inhibitors tested can neut- ralise the sulphuric acid in the shale. 10% ZnO appears to be an effective inhibitor of the reaction providing the AN/ZnO (90/10) is kept out of contact with surface material whose temperature can be as high as 60¦C in summer. It is concluded that ANFO/ZnO (90/ 10) should be now tested in stemmed holes.

Jan 1, 1986

By B. R. List, E. R. F. Lord

The Syncrude open pit mine, located near Fort McMurray in northeastern Alberta, produces approximately 410 000 tonnes of oil sand feed daily, which, after undergoing a bitumen extraction phase, generates approximately 315000 tonnes of tailings solids daily. The tailings are used to hydraulically construct containment dykes and supporting beaches of the storage facilities. Tailings deposition commenced in May 1978 with the commissioning of the Mildred Lake Settling Basin which is currently composed of approximately 600M m3of solid sand approximately 300M m3of contained fluids with fine tailings in suspension for consolidation. Two other storage facilities, commissioned over the past six years, have been developed to store sand and consolidated fine tailings referred to as mature fine tailings. Fine tailings reduction initiatives being developed will be successful in reducing future production of fine tailings volume by 20%. These initiatives include spiking (addition of fine tailings to coarse tailings lines for deposition), composite tailings (addition of gypsum to promote consolidation) and freeze/thaw dewatering, also to promote consolidation. The mandate of research efforts is to enhance tailings disposal and to develop economical and technically feasible reclamation initiatives. Final tailings landscapes will be geotechnically stable and ecologically productive to minimize or eliminate long-term liability. This technical paper will review the design philosophies of the current facilities and provide an overview of the areas of continuous improvement in the field of tailings management practices through the concerted research efforts and their implementation.

Jan 1, 1997

By Debasis Deb

The first version of the longwall strata control and maintenance system (LSCMS) has been successfully developed by the Strata Control Re¬search Team at the University of Alabama. The system includes a software package designed to monitor shield leg pressure, interpret the data and predict the forthcoming roof loads and the existence of geological anomalies. It can also detect maintenance problems of the face equipment. The LSCMS was installed underground and connected to the surface terminals at Drummond's Shoal Creek Mine in Alabama. The system has proven to be a useful and practical system for improving safety and efficiency in coal-mining operation. The Shoal Creek Mine is a new, large coal mine operated by Drummond with two longwall panels. The Blue Creek seam is the primary source of coal production. It is located at a depth of 275 to 440 m (900 to 1,450 ft) below the surface with an approximate 2% southwest dip. Typical strata conditions are represented by two stratigraphic columns (Figs. la and b). A fireclay/dark shale parting (called Middleman) 0.2- 0.7-m- (1- to 2.5-ft-) thick exists between the Mary Lee and Blue Creek seams. Mining conditions vary from area to area. This mainly depends on the Blue Creek seam thickness that ranges from 0.9 to 2.9 m (3 to 9.5 ft). The thickness of the Mary Lee and the parting is relatively consistent with a to¬tal of 0.9 m (3 ft). They are mined when the Blue Creek seam becomes thinner. In most of the panels, the immediate roof is composed of sandy shale 1.5-

Jan 1, 1997

By G. E. Karantzavelos

Introduction Pure alunite (KAl3 (SO4 )3 (OH)6 ) contains 37% A1203. In the alunite ore found on Milos Island, Greece, opal is the principal gangue while some aluminum, iron, and titanium oxides are also present. Processing of alunite ore leads to the recovery of potassium sulfate, alusil (alumina-silica mixture), and sulfur dioxide. An interesting process has been developed in Greece (Svoronos, 1977) consisting mainly of roasting the alunite ore mixed with KCl to disrupt the mineral lattice in preparation for separating its components. The thermal decomposition of alunite at approximately 600°C occurs by the reaction: KAl3 (SO4)3 (OH)6 + nSiO2 + 6KC1 - 4 K2SO4 + 3 A1203 . nSiO2 + 6 HCl + 3H20 According to the process pure alunite mixed with 543 kg KCl, 840 kg K2SO4, 370 kg alusil, 264 kg HCl, and 65 kg H2O are produced. The roasted calcine is leached in hot water. The potassium sulfate leach slurry is then thickened and washed to obtain a solid residue (alusil) plus a solution rich in potassium sulfate. Assuming the alunite ore feed consists of 50% to 60% alunite, the solid residue might consist of approximately 22% to 27% A1203, silica, iron, and titanium oxides. This leach residue could be digested in a hot sodium hydroxide solution to dissolve alumina. An amount of the alumina (approximately 10%) would not dissolve. In addition, part of the silica would dissolve requiring removal from the solution in a subsequent desilication operation. The same leach residue could be attacked by mineral acids such as a diluted hydrochloric acid to extract aluminum chloride (Sawyer et al., 1983). Alumina and aluminum are presently produced from bauxite of which Greece has important reserves. If this aluminous material (alusil) could be beneficiated by any physical process, then it would be considered as a raw material for the production of fire-clay refractories instead of an alternate source of alumina. Experimental procedure Extensive laboratory work (mineralogical and chemical analyses) indicates that alusil is a mixture of liberated (mostly) alumina and silica particles, not a natural silicate mineral. Table 1 shows the chemical assays of two alusil samples that were obtained from a roasted alunite ore leaching pilot plant. The samples used for the experiments were a very fine alusil powder (K80 = 400 mesh, 38 µm). These were pulped in tap water. Desliming of the pulp before each flotation test was ineffective. Flotation tests were performed in a 2000 ml Denver cell. A standard 500-g sample was first conditioned at a pulp density 50% solids for 5 min with hydrofluoric (HF) acid solution (40%). The temperature of the conditioned pulp was measured and kept nearly constant at 50°C. The pH of the conditioned pulp was also regulated to 2.5-3 with HF solution. Then ARMAC C solution (2%) as well as two drops of fuel oil and one drop of AEROFROTH 65 were added and the pulp was reconditioned for 2 min. After conditioning, the viscous pulp was transfered to the flotation cell. It was then diluted with warm water to about 15% solids and floated to separate silica from alumina particles. A rougher froth product that was cleaned and recleaned was obtained from the flotation tests.

Jan 1, 1987

By Thomas L. Starks

Surface soil/spoil Samples (0-10 cm) from experimental test sites in western North Dakota were aseptically collected during August 1975 and each month (May through September) during 1076 and 1977. Selected samples were Cultured in a defined inorganic medium and after six weeks the algae were identified. Chlorophyll u content of the soil/spoil was used as a measure of the algal abundance. Soil physical-chemical properties, species variety and abundance were statistically analyzed. All test sites revealed distinct soil algal communities and demonstrated a successional trend as evidenced by significant increase, in species variety and bionmass over time. Some soil factors, calcium, copper, and phosphorus affected species variety and abundance at more than one situ. Others were important at specific sites; silicon and aluminum at the South Beulah test site; manganese sodium and zinc at the North Beulah test site No. 1 and boron, cadmium and magnesium at the North Beulah test site No. 2. Topsoiled areas had higher species varieties and abundances when compared with control areas, as did plots treated with amendments such as leonardite and fertilizer Generally.

Jan 1, 1982