Search Documents

By G. Kosick, G. Dobby

CEET, an acronym for Comminution Economic Evaluation Tool, was jointly developed by MinnovEX Technologies Inc. and 13 major mining companies for the purpose of designing and predicting the performance of grinding circuits. It fundamentally differs from other methods by using as its’ data set a geostatistically significant population of hardness data distributed across the mine block model. Historically the characterization of an orebody for the purpose of either designing a grinding circuit or predicting the performance of an existing circuit has been done with a relatively limited number of discrete samples. In addition to power selection, shell sizing, and costing for multiple circuit options, CEET also outputs tons per hour, P80, and operating cost on every mining block for subsequent integration back into the block model. This paper will provide an overview of what CEET is and how it works.

Jan 1, 2001

A field method combining solvent extraction and paper partition chromatography permits a simple and rapid semiquantitative estimation of gold in siliceous, argillaceous and sulphide ores. The method will facilitate the eyaluation of prospect samples in which the gold is too fine for separation by panning.Ethyl alcohol-hydrobromic acid mixtures are suitable for chromatographic development of the gold complex, and give clear reproducible definition of the gold zone. Substitution of commercial "methylated spirits" for the ethyl alcohol gives equally good definition, improving the potential of the method for field use.A batch of six samples in the range of 0·5 to 5·0 dwt/ton can be completed in two hours. The range may be extended by simple modification to higher or lower values.INTRODUCTIONIn a chromatographic method described previously (Lever 1958, Nevill and Lever 1959), gold from a standard volume of ore clamped between -plate glass was extracted by aqua regia on to the paper. After cautious drying the chromatogram was developed by an ethyl acetate-nitric acid-water mixture and gold was identified by spraying with stannous chloride solution. Sensitivity of the method in the low range was poor. The brown line obtained in the 1-3 dw/j ton range, caused by movement of gold in the reduced form, was not considered to be a satisfactory confirmation of the presence of gold. It was felt that the method would be improved by using a more elegant extraction and applying developing conditions which would produce a well defined purple line at all gold values. Iron was a limiting factor, and a method of eliminating its interference was needed.The method now developed overcomes these shortcomings, and gives a reliable result with a purple line for assay values of 0·5 dwtjton and over. Gold is dissolved from an...

Jan 1, 1964

By Richard Klimpel

"Over the last 15 years, there has been a number of plant scale sulfide mineral flotation tests organized by this author specifically aimed at understanding how flotation rate varies with reagent type and dosage. With regard to the Interaction of collector dosage, particle size, and frother type, the eight specific trends listed in the paper (Illustrated with data from two specific case studies) are qualitatively the same for almost all plants studied in some depth. The Interaction of flotation rate K and equilibrium (Infinite time) recovery R in the plant has been denoted as the R/K trade-off. The effect of collector dosage on the rate of flotation of specific particle size intervals is particularly interesting and once understood, is quite useful In understanding how industrial flotation plants respond to changing reagent type and dosage. The location and magnitude of the R/K trade-off can be different for various ores and various plant configurations, but the RIK trade-off is almost always present. The purpose of this paper is to clearly describe and illustrate the nature of this very Important flotation system Interaction so that operating engineers have a starting reference point for beginning successful plant Improvement studiesIntroductionIt is well recognized by industrial froth flotation plant operators that improving existing sulfide circuit performance is often difficult due to the self-compensating systems nature of the froth flotation system, e.g. Klimpel (1988, 1989, 1995). Extensive plant testing with existing and new reagents by this author throughout the world has clearly shown that one of the more important self-compensating mechanisms is the Interaction between collector dosage, frother type, and particle size. The term self-compensation in flotation simply means that as the plant operator consistently changes one parameter in the same direction, the nature of the froth flotation system Is such that the circuit will eventually begin to resist this controlled parameter change by automatic (uncontrolled) changes In other parameters and the overall circuit performance will go through a maximum or minimum (hence causing the operator to stop the parameter change)."

Jan 1, 1997

By J. D. Miller, C. L. Lin

Appropriate software and hardware necessary to adapt a x-ray CT analyzer for determination of coal washability has recently been developed and sucessfully tested for well characterized samples under laboratory conditions. Evaluation of the CT-based analyzer under simulated on-line conditions is also presented to verify the on-line capabilities of the newly developed x-ray CT analyzer for the control of coarse coal cleaning circuits. The investigation shows that the data obtained from CT washability analyses compare favorably with experimental sink-float data. Further, image frequency was considered to evaluate the CT-Based coal washability analyzer for simulated on-line conditions. Specifically the number of observations (image spacing) needed for accurate sampling and the total time required to perform the calculations for a representative data set were determined.

Jan 1, 2001

By Yi Yang, Xiuzhu Su, Wei Sung Ng, Shuiping Zhong, Miao Chen

With over 260 tons of gold reserves, the Shuiyindong gold mine is one of the largest Carlin-type gold deposits in China. A particular challenge in the processing of the ore is the presence of carbonaceous compounds, which can cause substantial losses in recoveries via the preg-robbing and adsorption of gold. To investigate the structural properties of the native carbon and to compare between different characterization techniques for such compounds, pre- and post-flotation mineral samples containing 0.9–4.8% non-carbonate carbon from the Shuiyindong mine have been examined via mineralogical and thermogravimetric approaches, as well as spectroscopic techniques, including X-ray photoelectron spectroscopy (XPS), near-edge X-ray absorption fine edge structure spectroscopy (NEXAFS), solid-state 13C nuclear magnetic resonance (NMR) spectroscopy, diffuse reflectance infrared Fourier transform (DRIFT) spectroscopy, Raman spectroscopy and preg-robbing measurements. NEXAFS and DRIFT yielded the most reliable results, indicating that 60–75% of the organic carbon in all samples consist of aliphatic alkenes with substantial unsaturated content, highly similar to activated carbon, with the remainder being graphitic and humic. Speciation by XPS was sub-optimal due to spectral overlaps between graphitic and aliphatic carbon, and between carboxylic and carbonate functionalities, while NMR spectroscopy could not provide reliable speciation of the carbon groups. The preg-robbing strength was strongly correlated to the aliphatic content and structural disorder in the carbon, while no such relationship was found with the graphitic and humic content.

Nov 29, 2021

By Richards S. M

The abundances and abundance relationships of lead, zinc, copper and silver in the major sulphide lenses at Broken Hill are examined, and their possible geochemical significance discussed.When expressed as atoms per cent, zinc is the most abundant base metal throughout the whole .group of orebodies, the highest average lead: zinc ratio (No. 2 lens) being about 0·45, the lowest (No. 1 lensZinc Lode group) being in the 0·12-0 ·14 range. Lead and silver are clearly higher in the lower two orebodies, but the abundance of zinc shows no apparent relationship with stratigraphical position. Among the base metals copper is conspicuously low and remarkably uniform, a feature noted in other conformable orebodies.Although, as has been recognised for many years, abundances of silver and lead, and lead and zinc, are sympathetically related, correlation within the pairs is variable and generally of low degree. Silver and lead show distinctly the better correlation, particularly in No. 3 lens. On the basis of lead: zinc ratios, No. 2' and No. 3· lenses, on the one hand, and the No. 1 lenses, Rhodonitic and Siliceous Zinc Lodes on the other, constitute two groups. However on the basis of silver : lead ratios, No. 3 lens stands alone, No. 2 lens showing clear affinities with the higher layers. Ternary relationships between copper-zinc-Iead and silver-zinc-Iead emphasize the very close constitutional relationship between the No. 1 lenses and the two "zinc lodes".The possible implications of these relationships are then discussed in the light of the' two principal theories-hydrothermal replacement or chemical sedimentation-held for the formation of the Broken Hill ores. It is pointed out that the ratios of the four metals in the ores are rather different from those found in most igneous and sedimentary rocks, and in seawater. For 'example, whereas copper and zinc are present in almost equal amounts in most terrestrial materials, copper in the ores is only about one-hundredth of the amount of zinc. Lead has increased somewhat, but the ratio of silver to lead has fallen; in spite of its recognition as a source of silver, the Broken Hill lode is impoverished in silver with respect to lead as compared with most common terrestrial materials.No solutions are offered to these prob'lems of abundance. Rather it has been the aim of the work to provide data, and to demonstrate the...

Jan 1, 1961

By Stephen C. Tadolini, Dennis R. Dolinar

The risk of injury caused by minor roof falls continues to increase in underground mining. Most ground control injuries result from small rock falls that occur in a supported area, but do not involve the failure of the support system. In the roof, these are the "skin failures" that occur between previously installed primary or secondary bolting systems. To minimize skin failures and the associated accidents, several devices were designed and tested in the laboratory to maximize stiffness, minimize material thickness and weight, and ease material storage and handling on roof bolting machines. The goal of this project was to design and evaluate devices that can be installed with traditional primary or secondary roof supports, and that are easy to handle/install under temporary or previously supported roof.

By Olav Mellgren

Part I. The interaction between potassium ethyl xanthate and lead salts has been studied thermo-chemically. It is shown that ethyl xanthate reacts with lead carbonate, basic carbonate, thiosulfate and sulfate according to principles of simple chemistry, whereas reactions with lead sulfite, metasulfite, basic thiosulfate and hydroxide at high pH are associated with secondary reactions. A new compound "xanthogen thiosulfate" is postulated. Part 11. Adsorption of ethyl xanthate on galena has been studied quantitatively and thennochemi-cally. It is shown that an ion-exchange mechanism governs the adsorption process and that the heat of adsorption of xanthate on galena is equivalent to the heat of reaction of ethyl xanthate with bulk lead salts. It is concluded that the entropy content of the surface "compound" on galena is different from that of a corresponding bulk lead salt. Alkali depression is in part shown to be due to the instability of the xanthate-galena system at high pH and to the formation of basic lead salts. Sulfate and carbonate ions are shown to have a stabilizing effect on the xanthate-galena system. PARTI. THERMOCHEMISTRY OF ETHYL XANTHATE AND OF ITS REACTION WITH LEAD SALTS In the past little attention has been paid to the chemistry of lead xanthate. It is known that xan-thates form slightly soluble compounds with lead and that suspensions of lead xanthates in alkaline solution decompose rather readily.' The solubility of lead ethyl xanthate is of the order of 2.6 x 10-6 moles per 1. At increasing pH the xanthate concentration of a saturated solution contains more xanthate. Thus at pH 11 this xanthate content is about 100-fold larger than at pH 7.1 Xanthates are known to be consumed when added to a suspension of slightly soluble lead salts such as lead sulfate and lead carbonate. It is unknown to what extent this xanthate consumption is due to a simple chemical reaction because, frequently, observations are made which reveal secondary reaction products in such reactions. Thermochemical study of the reaction between xanthate and lead salts offers a means to clarify the significance of these reactions as the enthalpy changes can be accurately predicted from heat of formation of lead salts in pure solution reactions. In the present work the heats of formation of lead ethyl xanthate from potassium ethyl xanthate and lead salts are determined and some thermochemical aspects of xanthate in solution are studied. The results of these investigations are presented in Part I. In Part II the heat of adsorption of ethyl xanthate on galena surfaces is presented. All enthalpy changes were measured directly in a microcalorimeter. Calorimeter: The calorimeter used for measuring enthalpy changes was similar to that used by Redinha and Kitchener2 which was based on a description by Derbyshire and Marshall.3 Other useful references4,5 are listed. A sketch of the calorimeter

Jan 1, 1967

By Robert Hopler

It is the nature of the initial detonation to the powder around the cap which governs the greater or less effect of the explosion of the whole charge. The cap communicates to the first particles of powder a disruptive impulse, which, according to the nature and strength of the cap, more or less completely overthrows their equilibrium and decomposes the powder with great energy, setting up sympathetic vibrations that explode the particles of powder in turn by the violent disturbances or friction between them in a regular succession of impulses and decompositions, which, if started with sufficient energy, are of such intense heat and velocity that the rupturing force of the explosive is developed practically instantaneously. This detonation has already been shown to be not only the result of mechanical force, but a combination of extremely sudden chemical and dynamical reactions which set up vibrations to which different powders are more or less susceptible, and these explosive reactions will be propagated through the mass of the powder according to the intensity of the vibrations and the resistance with which their motion is opposed by the nature and consistency of the powder, whether it be difficult or easy to oxidize, soft and plastic like dynamite, or hard. If the initial detonation of the powder surrounding the cap is of the highest degree, the vibrations will be most intense and will be propagated further through the mass than by a poorer detonation. Hence the different degrees of detonation. Unless the first particles of powder are so thoroughly decomposed by a detonation of high order, or first degree, as to convey the necessary heat and energy to detonate the whole charge, the greatest force of the powder will not be developed. There will frequently be unbottomed holes or pieces of unexploded powder scattered about, or both, and the air in the mine will be contaminated with some obnoxious gases that have not been completely oxidized.

Jan 1, 2007

By H. Tveit, E. H. Myrhaug, J. K. Tuset

Silicon metal as a commodity material is produced by carbothermic reduction of quartz in electric submerged arc furnaces, where CO2 forms as a by-product. Since 1997 the Norwegian Ferroalloy Producers Association have been engaged in research programmes aiming for reduced CO2-emissions associated with fossil carbon in their processes. One important issue has been to study how charcoal and wood chips perform compared to coal and coke in the silicon process. The ability of the carbon-rich reduction materials to react with SiO-gas is commonly assumed to be of large importance to the performance of the process. Based on laboratory experiments with different carbon materials, combined with estimation of parameters in a mathematical model of the reaction between carbon and SiO-gas, a foundation for a theoretical study of the performance of the carbon materials in a silicon furnace is established.

Jan 1, 2004

In the spring of 1944 the Congress passed Public Law 290 (58 Stat. 190, 30 U. S. C. Sec. 321) "authorizing the construction and operation of demonstration plants to produce synthetic liquid fuels from coal, oil shales, agricultural and forestry products, and other substances, in order to aid the prosecution of the war, to conserve and increase the oil resources of the Nation, and for other purposes." Section 2 reads: "In order to carry out the :purpose of this act, the Secretary of the Interior is authorized- (a) to conduct laboratory research and development work, and, with pilot plants and semi-works plants, to make careful process engineering studies, along with structural engineering studies, in order to ascertain lowest investment and operating costs necessary to determine the best demonstration plant designs and conditions of operation;

Jan 1, 1948

Aamot, Olav Crone, Chem. Engr., Norsk Elektrokemisk, Kongensgt. 18, Olso. Norway. '29 Abadilla.-Quirico A., Dir., Bureau of Mines Manila, P. I. '38 Abbott, Clarence E., V.P., Charge of Raw Materials, Tennessee Coal, Iron & R.R. Co., 1212 Brown-Marx Bldg., Birmingham, Ala. '04 Abel, Raymond L., Prof., Dept. of Pet. Refin., Univ. of Pittsburgh Pittsburgh, Pa. '29 Abel. Walter D., Cons. Engr 1839 Holmby Ave., W. Los Angeles. Calif. '32 Abele, Louis T R. F. D. 5. Susquehanna Trail, N., York. Pa. '31 Abell, Leo M., Ore Dressing Investigator, School of Mines Adelaide, S. Australia. '31 Abenius. Hakan V., Mine Supt., Bolidens Gruvaktiebolag Boliden, Sweden. '37 Aborn, Robert H., Asst Met., Research Lab., U. S. Steel Corp. Lincoln Highway, Kearny, N. J. '19 Abraham, W. E. V., East India United Service-Club, 16 St. James' Sq., London, S. W. 1, England. '28 Abrams. Charles Jackson 1624 17th St., Denver, Colo. '36 Abstein, Henry T., Engr. & Mgr., Profile-Tamarack Mines Co Yellow Pine, Idaho. '27

Jan 1, 1938

By G. L. Oldright, F. S. Wartman

"In the process of smelting copper ores and secondaries in the reverberatory furnace to produce a copper matte and a slag low enough in copper content to be discarded on the dump, it is essential to the best functioning of the process that most of the iron in the material charged into the furnace be at the end in the form of sulphide in the matte or ferrous oxide in the slag. Ferric oxide and magnetite present in the charged material should be reduced to ferrous sulphide or oxide. Ferric oxide offers no difficulty in reduction, at least to the magnetite stage, because it reacts very readily with sulphides at quite low temperatures. Magnetite is less reactive and consequently more resistant to slagging, so that the furnace man must take advantage of all factors favoring its reduction in order to prevent accumulations in the furnace.In order to determine these factors more definitely, the Bureau of Mines in cooperation with the Department of Metallurgy, University of Arizona, has undertaken at the Southwest Experiment Station an investigation of the effect of various factors upon the rate of reduction of magnetite by ferrous sulphide. A previous paper's reported the nature of the reactions taking place and the effect of various physical factors when only pure sulphide and oxide were present. Since in the actual smelting operation, many other substances are also present, it seemed desirable to make a study of the effect of their presence upon the rate of reduction of magnetite by ferrous sulphide. Such a study has been made; the work done and the results obtained are described herewith.As will be shown later, it has been found that of the substances usually present in the smelting charge, silica and magnesia accelerate, whereas lime, alumina, and cuprous sulphide hinder the reduction of magnetite by ferrous sulphide.No report of a previous laboratory investigation of this subject has been found. Almost all furnace operators have made at one time or another at least qualitative ccmparisons of the effect of various changes in operating oonditions upon the behavior of magnetite in the furnace, but the conclusions derived from the experiments have never been published."

Mar 1, 1931

By Frank L. Wideman

THE TREND towards larger quantities of waste in materials handled at metal and nonmetal mines (excluding fuels) continued. A gain of 10 percent from 1962 in the tonnage of waste removed in mineral operations reflects the kind of technological problems being encountered. Technology has a major role in the mineral industry in the task of supplying raw materials obtained from resources occurring beneath the surface of the earth and used in manufacturing commodities essential to modern living. Changes in technology are often brought about by such factors as variations in economic conditions, differences in physical properties of raw material and changes in mineralogical compositions of ore. Mining is usually begun on the richest and most accessible of known deposits, and when these are exhausted, is continued with leaner ores or with less accessible deposits that are either lying at greater depths or are more remote from markets. The increasing difficulties of extraction and depletion of reserves are offset by improvements in extraction technology, improved transportation, and exploration for new deposits. Although depletion has prevailed at many individual mines and in many districts, technology has been the means of providing for increasing demands of an expanding economy with adequate supplies of minerals despite either the changing character or decreasing grade of certain ores. This has been accomplished by various methods applicable to minerals. Among the implements of technology are utilization of lower grade or more complex refractory ores by mass mining, concentration, processing, recovery of byproducts, and mechanization. Better methods to find concealed deposits or to penetrate to greater depths also have been helpful in maintaining a supply of particular minerals.

Jan 1, 1964

Council Members 1988/1989, left to right: Row 1 (seated): H.E. James, P.W.J. van Rensburg, Dr H. Wagner, B.C. Alberts, C.E. Flvaz (President), H.G. Mosenthal, R.D. Beck, Professor A.N. Brown, Dr P.R. Jochens Row 2 (standing): P.C. van Aswegen, J.P. Hoftman, D. Wllson, P.M.T. White, K.A. van Gessel, Dr LA. Cramer, J.S. Freer, V.J. Moore, G.A. Brown, R.A. Snodgrass, J.D. Austin Row 3 (standing): Dr G.A. Fourle, Dr J. Lurle, A.M.P. Henderson, R.P. Mohring, J.A. Cruise, J.L. Nel, H. Scott Russell, J.P. Deetlefs, D.A.J. Ross-Watt Inserts, top row: K.R. Beard, N.J. De~ine, R.J. Dlppenaar, G.T.G. Emere, Dr J-P. Franzidls, Professor R.P. King, J.G. McCallum. Bottom row: G.Y. Nisblt, Professor R.P. Plewman, Dr R.E. Roblnson, Dr O.K.H. Steften, P.A. van Wlelllgh

Jan 1, 1989

By W. Vorster

Bateman Engineering Project's acid-plant track record goes back to 1977. Bateman Engineering can design sulphuric plants based on gas from sulphur burners, metallurgical off gas as well as pyrite roasting systems. Bateman Engineering has a technology marketing agreement with NORAM Engineering Ltd of Canada to provide state-of-the-art, well-proven acid plant technology, and also has access to roaster technology from several sources, including Chinese technology. Utilising the Noram technology agreement, Bateman was awarded the Engineering and Procurement (EP) contract for the Ambatovy Nickel Project, Sulphuric Acid Facilities in 2007. This is the first Greenfield sulphuric acid plant Bateman has designed for many years, producing a combined 5,500tpd, and is one of the largest sulphur burning acid plants in the world. This paper gives an overview of the sulphuric acid plant for the Ambatovy Nickel Project, advantages of Noram?s unique technology on offer, an overview of work conducted on a recent study of an pyrite roasting acid plants as well as a new technology currently being developed by Bateman for the direct combustion of solid sulphur to form sulphur dioxide.

Jan 1, 2009

By W. Vorster

Bateman Engineering Project's acid-plant track record goes back to 1977. Bateman Engineering can design sulphuric plants based on gas from sulphur burners, metallurgical off gas as well as pyrite roasting systems. Bateman Engineering has a technology marketing agreement with NORAM Engineering Ltd of Canada to provide state-of-the-art, well-proven acid plant technology, and also has access to roaster technology from several sources, including Chinese technology. Utilising the Noram technology agreement, Bateman was awarded the Engineering and Procurement (EP) contract for the Ambatovy Nickel Project, Sulphuric Acid Facilities in 2007. This is the first Greenfield sulphuric acid plant Bateman has designed for many years, producing a combined 5,500tpd, and is one of the largest sulphur burning acid plants in the world. This paper gives an overview of the sulphuric acid plant for the Ambatovy Nickel Project, advantages of Noram?s unique technology on offer, an overview of work conducted on a recent study of an pyrite roasting acid plants as well as a new technology currently being developed by Bateman for the direct combustion of solid sulphur to form sulphur dioxide.

Jan 1, 2009

By O. T. Rämö, E. Suikkanen

Episyenites are sub-solidus, quartz-depleted alkali-feldspar-rich rocks. They form veins and lenticular bodies in granitoid rocks and migmatites in a late- to post-orogenic or anorogenic setting. Leaching of quartz is usually a response to a flux of weakly saline hydrothermal solution in circulation cells above cooling intrusions, where sufficient fluid-rock ratios and thermal gradients are achieved. Fluid Si-undersaturation is achieved by rapid cooling within the field of retrograde Si solubility or by temperature and pressure increase outside retrograde conditions. Some quartz may also be consumed in metasomatic reactions and in response to pressure fluctuation in sealed episyenite bodies. The small size and overall rarity of episyenites imply that conditions for episyenite formation are not commonly encountered in the crust. In addition to quartz depletion, episyenites record complex histories of metasomatic alteration and hydrothermal mineral growth. Nearly all episyenites have undergone Na-metasomatism, which may have led to the formation of nearly monomineralic albitite, and which is occasionally followed by late K-metasomatism, phyllic alteration, and argillization. Depending on the effectiveness of later compaction, recrystallization and vug-filling episyenites may preserve the macroscopic porosity formed by quartz dissolution and brittle deformation. Vuggy episyenites can act as significant sinks for metals carried by crustal fluids and host many significant U, Sn, and Au deposits worldwide. Rare earth-critical syenitic fenites around alkaline intrusions share mineralogical and genetic traits with episyenites.

By O. T. Rämö, E. Suikkanen

Episyenites are sub-solidus, quartz-depleted alkali-feldspar-rich rocks. They form veins and lenticular bodies in granitoid rocks and migmatites in a late- to post-orogenic or anorogenic setting. Leaching of quartz is usually a response to a flux of weakly saline hydrothermal solution in circulation cells above cooling intrusions, where sufficient fluid-rock ratios and thermal gradients are achieved. Fluid Si-undersaturation is achieved by rapid cooling within the field of retrograde Si solubility or by temperature and pressure increase outside retrograde conditions. Some quartz may also be consumed in metasomatic reactions and in response to pressure fluctuation in sealed episyenite bodies. The small size and overall rarity of episyenites imply that conditions for episyenite formation are not commonly encountered in the crust. In addition to quartz depletion, episyenites record complex histories of metasomatic alteration and hydrothermal mineral growth. Nearly all episyenites have undergone Na-metasomatism, which may have led to the formation of nearly monomineralic albitite, and which is occasionally followed by late K-metasomatism, phyllic alteration, and argillization. Depending on the effectiveness of later compaction, recrystallization and vug-filling episyenites may preserve the macroscopic porosity formed by quartz dissolution and brittle deformation. Vuggy episyenites can act as significant sinks for metals carried by crustal fluids and host many significant U, Sn, and Au deposits worldwide. Rare earth-critical syenitic fenites around alkaline intrusions share mineralogical and genetic traits with episyenites.

By J. Ritchey

This report describes the engineering feasibility and economic advantages of using a mobile bridge-type cross-pit belt conveyor system in conjunction with a large dragline to excavate and transport spoils in a typical Western surface coal mine. The studies show that such a system could be built to survive operational and climatic mining conditions, and that its implementation would offer a reduction in both acquisition and operating costs versus conventional mining units of comparable rapacity. Reclamation costs can also be significantly reduced, and the total reclamation process accelerated, making the cross-pit conveyor system attractive to mine Owners and environmentalists alike.

Jan 1, 1976