Search Documents

By W. H. Morris

I have been requested to present a paper on the slag from the basic Bessemer process, as prepared for fertilizing. Since Professor W. B. Phillips presented at the Birmingham meeting, in May, 1888, an able paper* on this subject, as it had been developed up to that time, there is little for me to add. Perhaps later practice may be best expressed by the homely proverb, " The proof of the pudding is in the eating." As the Pottstown Iron Company is the only concern manufacturing basic Bessemer slag in this country, the writer's personal experience in the use of it may be interesting. Our slag averages: P2O5, 21.37; SiO2,, 5.10; MgO, 5.90; Al2O3, 4.01; MnO, 5.56 ; FeO, 12.00; Na2O and K2O, 0.80; CaO, 45.26; total, 100.00. This gives over 76 per cent. of phosphoric acid and lime. In using this material for several years past on my lawn and garden, I have found it better than anything else I have ever tried ; and I am sure that any of you who had seen my green grass last month (January), wherever the ground was bare from snow, as bright as in early fall, would be forced to acknowledge the advantages of this soil-enricher. The grass on my private lawn, and around the company's office, is green the whole winter; and we have raised very good sod, by the use of this phosphate, where, without it, we were unable to get the grass to grow either from seed or by repeatedly sodding. The same statement applies to garden-truck; when the soil was first broken up, a good crop of vegetables was easily raised. My own gardener has had several premiums from Philadelphia seedsmen (notably, last year, the first premium for sugarcorn raised in the first part of July, being the first sample sent them). Our method of applying this material is to grind the slag very finely, so that at least 60 per cent. of it will go through a 150-mesh screen (i.e., say, 22,500 meshes to the square inch), and 90 per cent. through a 100-mesh screen (i.e., 10,000 meshes to the square inch). This fine grinding seems to be the main condition of success.

Jan 1, 1893

By Lee W. Abramson, Kenneth P. Akins

The authors have accumulated published data on residual soil and rock tunnels in the United States and have compared it to transit tunneling experience in Atlanta, Georgia, and tunnels in other soil and rock conditions. Two 6.1 meter (20 foot) diameter shield driven, compressed air tunnels were constructed for the Metropolitan Atlanta Rapid Transit Authority (MARTA) connecting the Five Points Station (central hub) with the Peachtree Center Station (first station on the north line). Because of the historic multi-story structures above the tunnels and the variety of subsurface conditions, a comprehensive ground monitoring and observation program was conducted. Conclusions are drawn regarding residual soil and rock ground response due to tunneling. Comparisons are made to ground response due to tunneling in other soil and rock conditions.

Jan 1, 1983

By C. R. Stephan

Explosion-resistant seals in underground coal mines isolate the environment within the sealed area from the active workings of the mine. The current United States Title 30 Code of Federal Regulations (CFR) requires these seals to be constructed of solid concrete blocks. The CFR also allows for alternative methods or materials to be used to create a seal if they can withstand a static horizontal pressure of 138 kpa (20 psi), provided the method of installation and the material used is approved in the ventilation plan. The purpose of this report is to identify those explosion- resistant seals that have been tested and meet or exceed all the requirements of the CFR.

Feb 24, 1997

By M. G. Driessen, H. E. Criner

Possible applications of cyclone thickeners for: (1) clarification of the washery water and, (2) recovery of fine coal from the plant bleed. The paper shows: (1) that it is possible to remove all particles including the very finest, from the circulating water, thus obtaining a closed water system and, (2) that reduction of the ash content of the solids of the plant bleed is feasible by means of cyclone thickeners. Performance data for different size cyclones is given in the form of graphs.

Jan 1, 1950

By Harry: Lobb Verakis

Mining operations have made tremendous strides in improving the safety of blasting as shown by the significant and continual decrease in fatalities and serious injuries. Advances in blasting technology and blasting practices have played a significant role in reducing fatalities and injuries. However, even with the decline of fatalities and injuries blast area security continues to be by far the leading factor in blasting accidents. Even though there continues to be an increase in the use of industrial explosives and blasting agents in the U.S.A., the decline in fatalities and injuries from blasting accidents has persisted.

Jan 1, 2010

By C. A. Nogueira, F. Pedrosa, F. Margarido, R. N. G. Guerra

"A hydrometallurgical process for recycling spent Zn-MnO2 batteries was developed, involving leaching with sulfuric acid, purification by precipitation and metals separation for further recovery. Leaching of zinc oxide was easily attained while for manganese oxide was rather difficult depending on temperature and acid concentration. At 90°C and with the liquid/solid ratio of 20 L/kg, more than 95% of zinc is recovered in 30 minutes with 0.5M H2SO4. To attain similar recovery for manganese, higher levels of acid concentration and time are needed (e.g 0.7 M and 2 hours). After leaching a purification step is necessary to remove iron co-dissolved through Fe(III) precipitation. Separation of zinc from manganese by solvent extraction with 1M DEHPA follows in the process route. The countercurrent multistage separation diagram developed allows the production of a zinc electrolyte with 120 g/L Zn and 0.005 g/L Mn, and a raffinate with 16 g/L Mn and 0.013 g/L Zn.IntroductionThe recycling of spent Zn-MnO2 batteries is carried out by dedicated recyclers using several process alternatives [1]. Most of the running processes use pyrometallurgical technologies [2] based on zinc distillation. Alternative treatments by hydrometallurgy have been reported [3-5] but its application is scarce.In order to contribute to the development of alternative solutions, a process for recycling batteries based on Zn-MnO2 systems has been studied. The process is based on the hydrometallurgical treatment of spent batteries in sulfuric acid media (Figure 1). The process starts with the physical processing by shredding using cutting grinders, where the batteries are opened and size reduced, allowing the liberation of the interior electrode particles or pastes. The fines can be then separated and the coarse material containing the steel scrap can be treated to remove the remaining aggregate electrode. The final scrap also contains some plastics and other non-metal materials and can be further valorized."

Jan 1, 2008

By E. C. Olsen

This paper describes the unusual hazardous conditions encountered in mining thick, inclined coal beds under heavy cover in Carbon County, Utah. This description includes heavy roof conditions, sloughing ribs, steep pitches, and severe bouncing experience. Emphasis is placed on the top bench system of mining and development in the top half of a 16-ft seam, under the roof rock, which is bolted, and the recovery of the bottom coal on retreat; success of bolted roof and ribs; and shuttle car haulage on pitches up to 25%. The use of protective cages for operators of face equipment, the guarding of belt conveyor systems to prevent injury associated with deliberate entry, and the positive lockout of electrical equipment is described and illustrated. Most coal mining areas of the Western United States are characterized either by thick beds, steep pitches or heavy cover. Individually, each of these may present inherent safety hazards that in- fluence mining. When all are met at one location, the combined effect is to make the safe operation of the mining property a challenge to management. These combined conditions are met in the coal mines of the Columbia-Geneva Steel Div. of the United States Steel Corp., in southeastern Utah. This coal bed measures up to 16 ft in thickness, the pitch is as much as 25% and mining is under a cover approaching 3000 ft. The Sunnyside coal bed is found in the Book Cliff Mountains, a great escarpment extending from west of Castle Gate, Utah, some 180 miles to Grand Junction, Colo. West of Green River, Utah, the Book Cliffs swing sharply to the north because of the domelike uplift of the San Rafael Swell to the southwest. It is in this northerly extension of the Book Cliffs that the Sunnyside coal in the Blackhawk Formation of the Mesa Verde Group, Upper Cretaceous Age is found. The strata are transected by numerous faults with from a few inches to as much as a hundred feet of displacement. All of these faults have had some effect on the mining operation, either in roof control or, in the case of major faulting, the pattern of mine development. MINING PRACTICES Mining has generally been confined to the Lower Sunnyside Seam which measures from 7 to 16 ft in

Jan 1, 1963

EXECUTIVE COMMITTEES OF LOCAL SECTIONS New York, L. W. FRANCIS, Chairman, WILLARD S. MORSE, Vice-Chairman. THOMAS T. READ, Secretary, Woolworth Bldg., New York, N. Y. P. A. MOSMAN, Treasurer. LOUIS D. HUNTOON. WILLIAM A. POMEROY. Boston HENRY L. SMYTH, Chairman. ALFRED C. LANE, Vice-Chairman. AUGUSTUS H. EUSTIS, Secretary-Treasurer, 131 State St., Boston, Mass. ROBERT H. RICHARDS, ALBERT SAUVEUR. Columbia FRANK A. ROSS Chairman. RUSH J: WHITE, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. FREDERIC KEFFER FRANCIS A. THOMSON,

Jan 2, 1915

The prediction and control of ground deformations due to underground mining are important considerations in the permitting, planning, and monitoring of coal mining operations. The prediction of mining-induced ground movements using the influence function method is a mature technology and is widely used in many coal basins around the world. Such movements mainly include subsidence, horizontal displacement, and horizontal and/or ground strain. Predictions can be accomplished using regional subsidence parameters and site-specific data.

Jan 7, 2020

Air tabling of zircon-rich non-conductor products containing quartz enables most of the fine quartz present to be rejected without a markedloss of zircon. The coarser quartz in the air table feed can be separated from the zircon by screening one or more air table products, the oversize products containing most of the quartz and little of the zircon. Air tabling, with or without screening, is more efficient than wet tabling alone for the removal of fine quartz, but not for the removal of coarse quartz. Practically all of the quartz can be separated from the zircon by using wet tabling in conjunction with hydraulic classification, or by using air tabling in conjunction with dry launder treatment, in which a degree of sizing takes place that is advantageous for subsequent air tabling.INTRODUCTIONBack-dune and inland beach sand deposits usually contain fine wind-blown quartz, and neither spiral nor wet table concentration, alone or in conjunction, makes a clean separation of heavy minerals from quartz. Many rutile plants recover rutile and zircon from a low-quartz, wet-table concentrates by means of magnetic and electrostatic separation; some rutile and zircon are lost in the table tailings. Other rutile plants, and two of the ilmenite plants in Western Australia, recover rutile or ilmenite respectively, from a spiral concentrate containing several per cent of quartz, and then subject the non-conductor product to an additionalgravity concentration process to separate the zircon from the quartz. Some zircon is lost in the additional gravity process, but all of the rutile or ilmenite in the spiral concentrate is, or should be, recovered as high-grade concentrate. The higher recovery of rutile or ilmenite by this treatment method is offset by the expense of drying part of the feed twice, as a wet process is usually used to separate the quartz...

Jan 1, 1962

By Jerry B. F. Champlin

The successful injection of liquids into subsurface permeable formations for production stimulation, storage, or waste disposal requires a rapid, precise, and accurate method of determining the permeability of porous solids. This report describes a method and apparatus, developed by the Bureau of Mines, that use the principle of specific-volume permeametry. Calibration of the apparatus over a wide range of permeabilities and standardization of several apparatus constants have eliminated many of the tedious calculations and problems of manipulation common to some other methods. Improvements in reproducibility and accuracy have resulted from reducing experimental measurements to one parameter--time. Specific permeabilities of reservoir rock samples are determined directly from a chart that relates elapsed time to a permeability equivalent to that determined by bubble-tube measurements.

Jan 1, 1962

By Thomas M. Barczak

The intent of this paper is to make mine operators and engineers aware of parameters which affect the loading behavior of passive roof support systems. The strength of a passive roof support element alone is not a meaningful measure of support performance. Passive roof support elements and the surrounding strata act as a system, responding to changes in the physical mine environment due to the extraction of coal and associated redistribution of stresses. The load- ing of a passive roof support element is a function of the stiffness of the roof support structure; a stiffer structure will react a higher load to a converging mine roof than will a more flexible structure. If the stiffness if the support structure is not properly designed, excessive loading will result due to the displacement of the mine roof, causing premature failure of the support. Ideally, the yield strength of a passive support needs to be no greater than that required to support the dead weight of the immediate mine roof, providing the post yield characteristics of the support are compatible with the irresistible convergence of the overburden strata and the support system continues to provide this resistance after reaching its yield load. Idealized design considerations for passive roof support systems in terms load-displacement characteristics discussed. The stiffness and yield characteristics of wood concrete cribbing, as determined controlled tests in the Bureau's Roof Simulator, are compared preliminary recommendations passive roof support utilization also provided.

Jan 1, 1987

EXECUTIVE COMMITTEES OF LOCAL SECTIONS New York L. W, FRANCIS, Chairman, WILLARD S. MORSE, Vice-Chairman. THOMAS T. READ, Secretary, Woolworth Bldg., New York, N. Y. P. A. MOSMAN, Treasurer. LOUIS D. HUNTOON. Boston HENRY L. SMYTH, Chairman. ALFRED C. LANE, Vice-Chairman. AUGUSTUS H. EUSTIS, Secretary-Treasurer, 131 State St., Boston, Mass. TIMOTHY W. SPRAGUE, HENRY A. WENTWORTH. Columbia F. A. THOMSON, Chairman. GEORGE W..RODDEWIG, Vice-Chairman. LYNDON K, ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. R. S. McCAFFERY, S. H. RICHARDSON.

Jan 7, 1914

The Dynamics and Thermodynamics of Absorbing Lithium of Ion Sieve Preparing Pollymetallic Nodules

Sep 13, 2010

Mineral deposits of the central New Guinea region (Gunung Bijih, Ok Tedi, Mount Kare, Porgera, Frieda River) and of southeastern New Guinea (Wau-Edie Creek, Wafi, Hamata, Hidden Valley, Tolukuma, Misima) are associated with hot, forceful intrusions of magma of mantle origin that penetrated thick Precambrian and Palaeozoic continental crust. The interaction of high- temperature melt with continental crust, and the differentiation of melt while in transit through thick crust, may be factors in generating ore. Mineralised intrusives in central New Guinea are a result of Neogene- Quaternary magmatism and were emplaced in a foreland thrust belt environment, a setting similar to the (mineralised) Laramide intrusions of southwestern USA. In both cases, central New Guinea and the Laramide, magmatism is not obviously subduction- related. Mineralised intrusives in south- eastern New Guinea (Wau-Edie Creek, etc.), also, are in a thrust belt setting, and are not obviously subduction-related. The association of. gold in southeastern New Guinea with a second (Pliocene) phase of igneous activity, rather than with earlier (Miocene) activity suggests that re-working by successive intrusions may be a factor in localising ore. This is seen, also, in the Bismarck-Solomon islands region where the richer deposits are associated with later (Pliocene) intrusives rather than with earlier (Eocene-Oligocene) intrusives. Unlike the mainland mineral deposits, those of the Bismarck-Solomon islands are clearly subduction-related.

Jan 1, 1991

By Goldney L. H

The authors review the literature and discuss the application of methods to the design of thickeners for ilocculated metallurgical pulps. The use and evaluation of flocculents is described. Experimental data show that design based upon laboratory settlingdata is acceptable. The economic aspect of design is also discussed.INTRODUCTIONFor many years there has been little change in the methods for the design of thickener installations. While modifications have been made in the method of applying the data all methods have been based on the observee settling rate of the solids. The development of a theoretical approach based on physical data would involve so many variables which affect the settling rate that the more practical approach of direct observation seems unlikely to be replaced as the basis of design.The advent of synthetic fiocculents has introduced a modification in operation which affects design and should be considered. The authors review the subject and attempt to bring it up to date with present day procedure. Until recently the original work of Coe and Clevenger (1916) remained the basis of thickener design. They described their observation of the different zones encountered in settling, namely clarification, feed, transition, and compression or thickening- zones. The solids pass through the transition zone in settling from feed density to some higher density where settling ceases and ·some compression or compaction effect controls. the density obtained. The point at which the settling zone ceases to exist is known as the critical point.

Jan 1, 1959

EXECUTIVE COMMITTEES OF LOCAL SECTIONS New York L. W. FRANCIS, Chairman, WILLARD S. MORSE,. Vice-Chairman. THOMAS T. READ, Secretary, Woolworth Bldg., New York, N. Y. P. A. MOSMAN, Treasurer. LOUIS D. HUNTOON. Boston HENRY L. SMYTH, Chairman. ALFRED C. LANE, Vice-Chairman. AUGUSTUS H. EUSTIS, Secretary-Treasurer, 131 State St., Boston, Mass. TIMOTHY W. SPRAGUE, HENRY A. WENTWORTH. Columbia F. A. THOMSON, Chairman. GEORGE W. RODDEWIG, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. R. S. McCAFFERY, S. H. RICHARDSON.

Jan 8, 1914

By A. J. Miscoe, W. M. McKewan, J. R. Bartels

The U.S. Bureau of Mines has established a wire rope research laboratory to examine the factors that affect the life of wire rope. Two 2 in-diameter 6x25 fiber core (FC) ropes were degraded on a bending fatigue machine. These were the second and third ropes in a series of tests on this construction and size rope. Tensile and nondestructive tests were performed on samples of the rope Lo determine the relationship between rope deterioration and rope breaking strength. The tests indicated that once a wire rope nears the end of its service life, both deterioration and the consequent loss of rope strength begin to increase at an accelerated rate.

Jan 1, 1992

By J. Nakayama

For drilling large diameter holes for deep foundations, the common and distressing difficulty of long standing has been in coping with ground containing rocky formations and boulders. Where geological formation contains weathered rock or boulders, or deep rock socket is specified, drilling equipment occasionally is found to be unable to drill through and therefore will need supplementary equipment and procedures. Incentive of the MACH Drill Development has been to realize a capable drilling system for rocks of weathered to fresh rock without losing its applicability to usual overburden. Through seven decades' experience of manufacturing and operation of boring machines, the best features of all sorts of drillhead are known such as the drag bit, wing bit, auger bit, diamond bit, rock roller bit, down-the-hole hammer bit, etc.

Jan 1, 1988

By B. Gigas, M. Preston, M. Giralico

Optimized mixer settler designs will now handle total flows of over 6,000 m3/hr.Computational Fluid Dynamics (CFD) is a timely and predictable tool for design development. Lightnin has the capability of using numerical analysis methodology to evaluate flow patterns and phase separation. CFD can show performance differences between changes, in mix tanks, in settler geometry, and in liquid depth, against variable flow rates. Understanding the differences allows the development of optimized designs. This paper focuses on the major design components of the mixer settler and how technological advances will lead to further improvements, when designing for today’s largest flow plants.

Jan 1, 2004