Search Documents

By Carlos Avalos Casillas, Saul Ortiz Landeros

The current work shows metallurgical results obtained at the Centro de Investigación y Desarrollo Tecnológico (Peñoles CIDT), as a continuation of the work first published in February 2012. With the aim of optimizing the economic values of the products, ores from San Julian (Fresnillo) were selectively floated to produce a lead concentrate and a zinc concentrate containing high silver values. In the laboratory, this included regrinding of the rougher and scavenger lead concentrate to increase the liberation of mineralogical species and thus lower zinc recovery. Cyanide leaching bottle tests were conducted to improve the value of the silver. It is proposed to leach the silver contained in the zinc concentrate and then recover the silver using the Merrill Crowe process. The results show a reduction of zinc recovery in the lead concentrate from 11.3% to 2.0% after regrinding to a P80 of 10 microns, improving the metallurgical quality and economic value of the lead and zinc concentrates. Also laboratory and pilot scale cyanidation tests showed that about 65 to 80% of silver will be leached from the zinc concentrate, after regrinding to a P80 of 10 microns. The proposed processing increases the economic recovery of silver from 72.7% to 78.8%.

Jan 1, 2014

By T. O. Allen, J. H. Atterbury

Laboratory and field tests during the past five years indicated considerable variation in the penetrating power of commercially available gun perforators. Many of the guns which achieved inadequate penetration in these tests have since been improved. However, recent productivity tests indicated the possibility of inadequate penetration or, at least, ineffective penetration in some wells. Laboratory experiments under simulated well conditions have demonstrated considerable plugging of the perforations, apparently as a result of factors associated with the shooting process and/or the drilling mud in the well at the time of perforating. The restrictions to flow per unit of hole depth caused by this plugging appears to be greater for jet perforators than for bullet guns of comparable diameter; however, because of the greater depth of penetration obtained with the jet guns, the total flow rates appear to he approximately equal. Limited testing with an experimental shaped charge suggests that less shot hole restriction and greater flow rates may result from larger-diameter perforations or other factors related to charge design. INTRODUCTION Gun perforating has been accepted for a number of years as a routine well completion method which is often preferred since it permits more selective operation of producing zones. Nevertheless, questions have continued to arise as to the effectiveness of the communication paths established between the productive formation and the interior of the casing. The basis for these questions has generally been failure to obtain anticipated fluid production rates through gun perforated completions in specific wells. These low productivities, together with the frequent recovery of bullets from well bores, were considered strong evidence of inadequate penetration. Laboratory investigations of the penetration performance of many of the bullet guns available as late as 1948 gave support to these indications. Subsequent electrical analog studiesl,2,3 indicated that the depth of penetration required to provide productivities equivalent to open hole was beyond the capacity of most bullet perforators evaluated in the early laboratory penetration tests. These results, together with the advent of the shaped charge in the field of oil well perforating, stimulated the interest of both oil operators and service companies in gun development. Improvements in gun design resulted in jet and bullet guns which appeared to be capable of providing sufficient penetration for most perforating jobs. However, some wells failed to yield satisfactory fluid production even after being perforated with the more powerful guns, again raising the question as to the effectiveness of the perforating operation. This fact, together with preliminary shooting into targets prepared with formation cores, indicated that factors associated with the perforating process and/or the fluids in the well bore at the time of shooting may reduce effective formation penetration and thereby decrease well productivity. These laboratory and field data prompted another phase in the investigation of the effectiveness of gun perforating: a program to determine the extent and seriousness of perforation plugging under simulated well conditions.

Jan 1, 1955

By F. P. Hassani

Today, mine backfilling has become an integral part of mining operations, both from a local and overall ground control point of view, and as regards mining techniques and environmental considerations. During the past decade, substantial research has been carried out to contribute to the better understanding of the mechanisms involved in mine backfill behaviour. This work involved analytical, experimental and numerical studies at different scales. Accordingly, this work has been aimed at developing backfill design guidelines for actual working conditions. Backfill design for deep mining conditions is complex and requires understanding of various elements. The most important of these elements are: backfill inherent strength parameters, backfill placement method, stope geometry and interaction between backfill and host rock. The mobilization of backfill strength parameters controls the backfill behaviour and thus, its failure mode. It is believed that the governing boundary conditions and backfill-rock interaction influence the backfill strength mobilization significantly. Accordingly, the interaction between backfill and host rock is an influential factor in overall backfill behaviour under applied loads. The focus of this research is to investigate the backfill-rock interaction, considering a nonlinear behaviour for both backfill and rock mass. Assuming typical stope geometry, the FLAC code was used to model the complex boundary condition associated with narrow vein mining conditions and to simulate the backfill behaviour. A comprehensive numerical study was conducted and the results obtained were compared against field observations. The analysis of findings provides qualitative results, which can be used for backfill design. Keywords: Numerical modelling, backfill, deep mining, non-linear behaviour, rock mechanics, backfill behaviour, narrow vein mining.

Jan 1, 2008

By J C. Waters

Pseudoclastic hydrothermal alteration textures occur within quenched coherent dykes forming part of a subaqueous dome complex (~4 Ma) onPonza Island, Italy. These textures are similar to those observed in considerably older (~500 Ma) subaqueous volcanic rocks at a number of localities throughout the Mount Read Volcanics in Tasmania and elsewhere in ancient volcanic sequences of this type in Australia. This is significant because the processes of formation, hydrothermal alteration and secondary mineralisation of ancient volcanic sequences may be better understood if we can make comparisons with modern analogues. Observations at Ponza imply that these pseudoclastic alteration features form synvolcanically or immediately after dyke emplacement and lava extrusion. This is compatible with scenarios presented for their formation in ancient sequences in the Mount Read Volcanics, Tasmania.

Jan 1, 1995

By Robert Martin

New Millennium ?a new project for an experienced mine building team ?Owns 100% of KeMag(Harris Lake) property ?Owns 80% of LabMag(Howells River) property -20% owned by Naskapi Nations of Kawawachikamah ?All founding directors are mining professionals : Geologists or Mining Engineers ?All have extensive experience in the iron ore industry ?The Project Office is located in Montreal, lead by a team of experienced iron-ore professionals Project Overview Geology & Resources Market Prospects Process & Product Development Development Plan Questions

May 1, 2007

By B. E. Warren

Jan 1, 1965

By Milton T. Pana

Computer techniques now have been applied to the solution of a wide variety of scientific and engineering problems in the mining industry, but generally not in great depth in any one area. In mining, the area covered in greatest depth and with the greatest success has probably been mine planning and to a lesser degree production scheduling. A rather comprehensive review of the literature related to mine planning and production scheduling indicates that contributions in these areas have been geographically, as well as organizationally, widespread. Of twenty-six papers reviewed, eleven were from industry, eight from educational institutions, four from computer vendors, two from the Bureau of Mines, and one from a private consultant. The conclusions that can be derived from the literature are: First, the-state-of-the art has advanced to the point that computing ore reserves and developing mining plans with the aid of the computer is now a routine practice; second, the application of the computer to mine planning problems has markedly improved our ability to estimate ore reserves, more accurately define pit limits, and determine an optimum mining sequence. MINE PLANNING The papers in this section deal essentially with the problem of determining the final pit limits of an orebody and the ore reserves associated with a given pit limit. The problem is probably best described by Soderberg25 and more recently by Reibell. 23. There are two techniques currently being applied to this problem by several mining companies: 1) the multiple-cone technique and 2) the Lerch-Grossman algorithm. The multiple-cone technique is the older of the two techniques and has the advantage of being more flexible, allowing an engineer to easily vary pit slopes in different sectors of the design. The technique can also be used to define intermediate pit contours. The Lerch-Grossman algorithm is appealing in that the final solution is given in the form of a true mathematical optimum. The technique is limited, however, in that the size of the blocks in the orebody model are a function of the desired

Jan 1, 1969

The purpose of this study was to examine the problems of underground coal mining in the United States, and to develop recommendations for an integrated Research and Development Program aimed at resolving these problems. Specific objectives of the study were as follows: ? To identify the existing inadequacies that have adverse effect on Health, Safety, External Environment, and Productivity. ? To identify opportunities for technological advance s to correct these inadequacies. ? To develop an integrated Research and Development Program designed to accomplish the advances identified. Many of the recommended tasks are dearly long range; this is especially true of those for study of future mining systems. However, funding recommendations in this Report are presented for a 5 -year period, since the developments accomplished during this period will undoubtedly be a factor in the formulation of the follow on tasks. Where applicable, the recommended Research and :Development could include development and test of pilot model equipment.

Jan 1, 1970

By S. Ramachandran, N. J. Grant, T. B. King

MANY investigations of the rate of the sulfur transfer reaction between carbon-saturated iron and blast furnace type slags have been made." It is evident that the reaction is complex, the rate being affected by the presence of elements dissolved in the metal that are readily oxidized and therefore capable of existing in the slag phase. Thus Goldman, Derge, and Philbrook- have shown that carbon, silicon, manganese, and aluminum, in order of increasing effectiveness, accelerate sulfur transfer from iron containing these elements to blast furnace type slags. Quantitative information is still, however, not available on the relation between what have been termed side reactions, such as silicon transfer and CO evolution, and the sulfur transfer reaction itself. In other words, the stoichiometry of the reaction has not been investigated. In the present investigation, the transfer of all reacting elements and the evolution of CO have been measured simultaneously in order to establish the mechanism of the reaction which occurs in practice. Information of this nature cannot be deduced from equilibrium studies. It should be pointed out that in kinetic studies of this type quantitative conclusions are applicable only to the system studied. This restriction should be borne in mind when attempts are made to compare results from different investigations. Apparatus The apparatus used enables slag and metal samples to be taken at frequent intervals and also provides a continuous record of the amount of gas evolved. A sketch of the apparatus is given in Fig. 1. It may be considered in three sections: 1) furnace section, 2) blank volume section, and 3) pressure measuring section. The furnace section is shown in detail in Fig. 2. It consists of two graphite crucibles, C and D, super-

Jan 1, 1957

By M. J. Nicol

On page 51, the equation numbered.... On page 52, the equation numbered .... On page 53, the arrangement of the equation.... Canadian reports Asbestos by G.O. Vagt.l0 pp. Chromium by D. G. Law-West. 6 pp. Iron and Steel by T. R. Mclnnis. 15 pp. Titanium and Titanium Dioxide by M. A. Boucher. 7 pp. Vanadium by D. Shaw. 7 pp.

Jan 1, 1984

By C. McAllister, D. Preece, J. Berendzen

The Multiple Blasthole Fragmentation (MBF) model was developed recently and has been reported in previous papers. The MBF model accepts inputs from the blast design, such as: location and orientation of each blast hole, stemming length, blast hole diameter, multiple decking, bench height, initiation sequence, etc. It models the effect on fragmentation of delay timing with its associated scatter for each blast hole. MBF has a statistical modeling capability for geological random variation of the attenuation of particle velocities. Also simulated is wave reinforcement due to the interaction of simultaneously arriving waves or diminishing cooperative contribution from long delay intervals between charges.

Jan 1, 2016

By L. A. Cramer

Platinum metal was first utilized by the Inca civilization in South America where it was found in alluvial deposits along the San Juan and Atrato rivers that lie between the Andean mountain range in Colombia and the Pacific Ocean. The nuggets found in these rivers average between 77% and 86%platinum, 7%?8% iron and small amounts of copper, gold and other Platinum Group Metals (PGMs). The Incas often alloyed platinum with copper to increase its workability and fabricated various ornaments from it.

Jan 1, 2001

Some major mineral deposits in northern Australia are found in preconsolidation slump disturbances in the sediments.In the retransported marine sediments at Tennant Creek, breccia beds and disturbances are found which have localized later mineral deposits such as the Peko copper orebody. These disturbances are thought to result from slumping, turbidity flow and various types of "semi-fluidized" subaqueous slides intermediate between slumps and turbidity currents.Movements are found to ~ause widespread disturbances in the sediments such that subsequent mineralization can spread through a large volume of rock giving rise to orebodies greater than those localized by tectonic structures.A similarity is noted between the sedimentary disturbances at Tennant. Creek and those at Mount Isa and Mary Kathleerr. It is suggested that disturbed beds which are host rocks to ore minerals in these mines may also be due to movements of the sediments before compaction.Certain characteristics of the slumped rocks can be recognized and limited generalizations can be made about the shape, extent and habit of these host rocks and the orebodies they contain.INTRODUCTIONSubmarine slumping and· turbidity current retransport are almost entirely responsible for some types of deep marine sediments.However, little attention has yet been drawn to slump deposits and associated disturbances bedded in the sediments as features localizing later mineralization.A study. has been made by the writer of the slump and associated phenomena of the ,Tennant Creek field where many mineralized bodies, including some gold and copper orebodies, occur as replacements of coarse fragmental slump...

Jan 1, 1960

Mineralisation was identified at Gladstone Hill as far back as the late 1870s-early 1880s, shortly after the initial discovery of mineralisation at what is now the Martha Mine. Indeed, early recovery problems associated with the Martha mineralisation led to the preferred development of ore bodies within what is now the Union Hill Joint Venture tenement; ore bodies such as Silverton, Amaranth, and Union to name a few. Gladstone Hill forms the basis of the Union Hill Joint Venture, a 50:50 joint venture managed by Au-Ag Resources Ltd (a fully owned subsidiary of Otter Gold Mines Ltd), and Welcome Gold Mines Ltd (a fully owned subsidiary of the Normandy Group). The joint venture participants also operate the adjacent Martha Mine. Mineralisation of Gladstone Hill, as with mineralisation at the adjacent Martha Mine, has been interpreted as a low sulphidation epithermal Ag-Au system hosted within hydrothermally altered andesites of the lower Coromandel Group. Drilling in recent years has successfully identified extensive mineralisation associated with a number of vein sets throughout the tenement including the Gladstone Vein set, the Moonlight Lode and more recently along a north-easterly trend towards the historic Favona workings. A wide range of vein styles is apparent, ranging in character from thin stock works to broader lode-style banded chalcedonic to cherty quartz and have been interpreted as representing multiple phases of emplacement. At shallower levels mineralisation is often hosted by vein clasts within vent breccias. Visible gold is rare, with mineralisation generally associated with very fine-grained pyrite, arsenopyrite and minor electrum. Percentage levels of combined sphalerite-galena-(+/- chalcopyrite) have been intersected at depth however these have been gold poor to date. The potential for the Gladstone Hill area remains to be clearly defined as drilling to date has yet to close off mineralisation both along strike and down dip. If further drilling is successful, the joint venture partners believe Gladstone Hill could contribute significantly to the economic future of current operations.

Jan 1, 2000

By Eduardo Macedo Junior

O presente trabalho descreve o desenvolvimento de uma nova especificação para a Linha de zincagem numero 3 (LZC#3) da Companhia siderúrgica nacional (CSN), de grande demanda e aceitação, alta produtividade e foco nos requisitos do cliente que tangem qualidade superficial e características metalúrgicas (resistência mecânica) em aços para atendimento do mercado Norte-americano. Este novo produto tem como característica o ciclo de recozimento com velocidade alta para obtenção de microestrutura 100% encruada na saída do equipamento e limites de escoamento e resistência acima de 500 MPa. A combinação dessas características do produto junto com as características do processo tornou a especificação “ASTM-A653MSS80CL1” um grande desafio para garantir qualidade superficial sem comprometer as propriedades mecânicas especificadas assim como a integridade do equipamento. O baixo custo de produção associado a alta produtividade desse produto fazem da especificação “ASTM-A653M-SS80CL1” um produto de extrema importância para a estratégia adotada pela CSN, mantendo dessa maneira sua competitividade no mercado Norte-americano e garantindo capacidade máxima de produção do seu equipamento em tempos de retração do mercado interno.

Aug 17, 2017

By John L. White

Vibratory driver/extractors do more than drive and extract sheet piles. I would say more than sixty percent (60%) of the time, vibratory pile driver/extractors are engaged in work that has nothing to do with sheet piles. This is the main reason I refer to this tool as a "driver/extractor", and omit the word "pile". I have spent the last twenty years applying the technology of the vibratory driver/ extractor to all areas of foundation construction. As you will see, the only limits are humankind's ingenuity.

Jan 1, 1997

By L. A. Cramer

Platinum metal was first utilized by the Inca civilization in South America where it was found in alluvial deposits along the San Juan and Atrato rivers that lie between the Andean mountain range in Colombia and the Pacific Ocean. The nuggets found in these rivers average between 77% and 86%platinum, 7%?8% iron and small amounts of copper, gold and other Platinum Group Metals (PGMs). The Incas often alloyed platinum with copper to increase its workability and fabricated various ornaments from it. With the arrival of the Spanish in the early 1700s, platinum was labelled a nuisance for the Spanish in their quest for alluvial gold because it concentrated with the gold and had to be removed by either extended amalgamation or by hand sorting. It was at this time that platinum received the root of its current name for the Spanish referred to it as platina del Pinto, platina being the somewhat derogatory diminutive of plata (silver). Pinto was a river in Colombia where the Spanish first distinguished it. The English eventually adopted ?platina? and it is only in recent times that the Latin name platinum has been accepted as the metal?s common English name. From its first introduction to European scientists in 1740, platinum was unappreciated because of its brittle nature and difficulty of working and as a result had little commercial value. Its ability to be dissolved in gold did lead to some counterfeiting of gold bullion and even to the debasement of gold currency.

Jan 1, 2000

By Luiz Gabriel da Silva Nascimento

Um material que vem sendo muito estudado quando imerso na matriz de outros materiais, são os nanotubos de carbono, uma forma alotrópica do carbono, que são milhares de vezes mais finos que um fio de cabelo, mas que apesar disso, possuem uma extraordinária resistência mecânica. O alumínio por apresentar um baixo peso específico e ter a facilidade de se unir a outros materiais pode nos fornecer excelentes propriedades e muitas aplicações tecnológicas. Através de ensaios metalográficos e mecânico, esse trabalho avaliou o comportamento microestrutural e de microdureza do alumínio depois da adição nanotubo de carbono e nanotubo mais níquel em sua estrutura. Foi usado um processo de fabricação por fusão com agitação mecânica por um pequeno motor elétrico e resfriamento brusco por água. Depois das análises nesses diversos materiais, com composição diferenciada, o que melhor apresentou propriedade mecânica foi o Al-3%Ni+nanotubo de carbono.

Aug 7, 2018

By Kray Luxbacher, Mario Karfakis, Erik Westman, Peter Swanson

Three-dimensional velocity tomograms were generated to image the stress redistribution around an underground coal longwall panel to produce a better understanding of the mechanisms that lead to ground failure, especially rockbursts. Mining-induced microseismic events provided passive sources for the three-dimensional velocity tomography. Surface-mounted geophones monitored microseismic activity for 18 days. Eighteen tomograms were generated and high-velocity regions correlated with high abutment stresses predicted by numerical modeling. Additionally, the high-velocity regions were observed to redistribute as the longwall face retreated, indicating that velocity tomography may be an appropriate technology for monitoring stress redistribution in underground mines.

By A. S. Argon, G. East

From their study of the anisotropy of grain boundary mobility in aluminum, the authors conclude that tilt boundaries have a higher mobility than twist boundaries because the atomic misfit at the pure-twist boundary is relatively small compared to the misfit at a tilt boundary for a given amount of misorientation. If this is true, then one would expect a twist boundary to have a lower grain boundary energy than the corresponding tilt boundary. Fig. 6, taken from the work of Gjostein and Rhines,10 shows that this is indeed the case for [001]-cu tilt and twist boundaries in the high-angle region, thus lending support to the authors' conclusion.

Jan 1, 1968