Search Documents

By R. Hummel

When the slope angles of the southern side of the Venetia open pit were required to be flattened by some 20 degrees after an analysis completed by De Beers geotechnical engineering in conjunction with SRK, the additional waste stripping tonnage generated was in the order of some 70 million tons. The potential cost of having to move this tonnage had a significantly negative effect on the Net Present Value of Venetia Mine, challenging the viability of the third pushback and rendering a potential fourth pushback completely uneconomic. This paper details some of the innovation that went into the design and planning process undertaken to virtually negate the instantaneous effect of the flattened slope angles and the associated waste tonnage as well as further improve the NPV of Venetia Mine and bring the fourth pushback back into economic viability. This process has become known as NPV+ and is anon going exercise in waste reduction/deferment and revenue advancement.

Jan 1, 2001

By B. Samanta

LHD (load haul dumper) is now used as a loading machine for intermediate mechanization in underground coal mining. For survival in the intense competition in the global business environment in recent years it is essential that LHD machine should be reliable and maintained effectively and efficiently. This paper seeks to study the reliability, availability and maintainability (RAM)of an LHD machine with failure and repair data by Markov modelling. The constraints and reasons for machine unavailability are outlined. The reliability and maintainability of an LHD and its subsystems are evaluated. Possible modification or design alternatives are highlighted. Reliability and maintainability of an LHD system are disappointing. There is room to take decisions on optimal maintenance planning and machine improvement from this analysis. Keywords: reliability, availability, maintainability, Markov model, LHD

Jan 1, 2004

By Rees J. Llewellyn

Improved product development, assessment methods and evaluation studies of materials for oil sands applications have traditionally focused on low and high stress abrasion and slurry erosion resistance mechanisms, because they were considered to be the predominant wear modes prevailing in oil sands mining, transportation and bitumen recovery. More recently with the very successful introduction of oil sands hydraulic transportation systems, there has been increasing use of crusher systems in which materials of construction are also required to have good toughness and gouging abrasion properties to withstand impact and the severe indentation and ploughing forces that are involved. To assess material property requirements for mitigating this additional wear mechanism, jaw crusher gouging abrasion tests using a modified ASTM G81 procedure, have been carried out on a range of wear materials of interest for oil sands mining service. The method involves a comparison of the wear losses that occur for reference and selected test plates when a controlled amount of standard feed rock is comminuted in a laboratory jaw crusher. Among the classes of material evaluated have been Q&T plate steels, austenitic manganese steel, chromium and chromium molybdenum white irons as plain castings and in laminated forms and also chromium carbide and tungsten carbide overlaid wear plates.

May 1, 2004

By L Hussey, H Thanasekaran, J Kohmuench

Conventional flotation technology has historically failed to achieve high recoveries when treating <15 µm particles (Lynch et al, 1981). The new StackCell™ flotation technology was developed to specifically target this particle size range, and was tested at pilot plant scale at Mt Keith Nickel Concentrator. The streams tested, Slimes Rougher Tailings and Fines/Slimes Cleaner Tailings, represent 21% and 11% of the total nickel lost to tailings in the plant. Laboratory scale test work indicated that an economically significant fraction of these losses was consistently available to be recovered by additional flotation. The pilot plant experimental scope included over 50 tests. A grade recovery curve for each stream was developed, as well as information on the effect of ore type, feed rate, wash water, air flow, collector and frother on the performance of the cell. The single StackCell was able to achieve nickel recoveries of 16.8% and 16.5% on the Rougher Tailings and Cleaner Tailings, respectively, at grades consistent with these blocks. Additional test work of the StackCell in a cleaner scalper duty yielded final quality concentrate with a maximum nickel recovery of 59.5% for the single stage StackCell. Laboratory scale simulation of the downstream impacts of the StackCell operating as a cleaner scalper indicated a net recovery benefit of up to 2.0% for this cleaner block.Tests were completed to compare residence time requirements of the StackCell, as compared to conventional flotation. In 55 seconds, the pilot plant StackCell achieved 50% of the recovery of a 960 second laboratory scale conventional flotation on the same feed material. The apparent improvement in flotation kinetics is attributed to the novel high intensity aeration system, which provides efficient bubble-particle contact thereby shortening the residence time required to achieve high recoveries. The smaller footprint and lower energy costs of such a cell are also benefits of this technology, which is being considered for industrial scale installation as a result of this test work. Given the industry’s historical poor performance treating slimes with conventional flotation, it is clearly best practice to challenge the status quo through innovative new technology, such as the StackCell.CITATION:Hussey, L, Thanasekaran, H and Kohmuench, J, 2017. The application of high intensity flotation technology at Mt Keith nickel concentrator, in Proceedings MetPlant 2017, pp 259–278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By I. Fafoutis

Laboratory column studies were conducted in order to assess the effectiveness of slag and red mud reactive barriers for cleaning up leachates generated at mining and waste disposal sites and loaded with copper and manganese. Solutions containing the metals of concern were prepared by dissolving the required quantities of CuSO4?5H2O and MnSO4?H2O in distilled water so that Cu concentration was 100 ppm and Mn 20 ppm. Flow rates of 25 mL.h-1 for Cu solution and 75 mL.h-1 for Mn solution were used in order to simulate aquifer water velocities of 1 ft/d and 3 ft/d respectively. Solutions were pumped upflow, in Plexiglas laboratory columns filled with each reactive medium, using peristaltic pumps. Measurements of middle and outflow column pH, redox potential, conductivity and elements concentration were performed to provide information regarding removal mechanisms for both elements and exhaustion/inactivation rates for each reactive medium. Both reactive media showed fairly good removal efficiency over the period studied. Copper was mainly removed by precipitation and formation of Cu(OH)2 while removal of manganese was due to precipitation of Mn(OH2).

Jan 1, 2006

The Mount Lyell Mining Field is Australia's chief productive source of copper. It is situated near Queenstown, on the western flanks of the West Coast Ranges, about 20 miles from the west coast of Tasmania (Fig. 1).The following observations on the mineral composition of the copper ores of the Mount Lyell Field are based on a...

Jan 1, 1939

In order to appreciate fully the place of palaeontology within the general framework of the geological sciences, consideration must be given to the time, about 150 years ago, just before the study of fossils was beginning to be applied to geological problems. At theend of the eighteenth century, almost all geologists recognised that fossils were the remains of animals and plants that had lived at the time when the rocks in which they occur were formed. It was also realized that many-some geologists thought all-rocks hadbeen formed under water, but as regards the order of succession in which these rocks had originated, and the relative ages of rocks found in different parts of the world or even of one country, only the haziest and most contradictory ideas existed.Around the turn from the eighteenth to the nineteenth century, a widely taught system of theories was that of the German professor, Abraham Gottlob Werner, who believed that the surface of the earth had once been covered by a universal ocean at whose bottom all rocks had been deposited. As the level of this ocean gradually subsided, older rocks-so Werner taught-are now generally found in the mountains or at great depth below the younger rocks; this was his "Primitive Division" which included granite, gneiss, schists, slates, basalt, porphyry and other igneous and metamorphic rocks, all of which he believed to be of sedimentary origin. Younger rocks, according to Werner, were formed at successively lower levels as the water receded. Next in age he placed a "Transition System" of limestones and greywackes; still younger the so-called "Floetz Division," which included sandstone, limestone, gypsum, salt, coal, but also some basalt, porphyry and other rocks; youngest were the alluvial deposits of recent clays, loams, sands and gravel. Thus, in the Wernerian system the age of a rock was determined on the basis of its petrographic properties and the height of its occurrence relative to sea-level.Here and there these ideas survived well into the nineteenth century. As late as 1825, Charles Darwin listened to lectures by Professor Jamieson, one of the last proponents of Wernerian theories in England. The fact that entirely different kinds of fossils occurredin rocks which were regarded as contemporaneous did not worry the theoreticians.It is, therefore, noteworthy and significant that the value of fossils for the interpretation of geological events was demonstrated to the geologists by an engineer and surveyor, WiIIiam Smith, who, although no professional geologist, has often been called the "Father of English Geology." His professional work, which was mainly concerned with drainage and irrigation projects, took Smith to all parts of England, where he sometimes journeyed as much as 10,000 miles in 11 year. Smith was a keen observer and, unhampered by theoretical speculations, he noted the occurrence of fossils and collected specimens wherever he went. Before long he realized that the same kind of fossils followed each other in successive layers of rocks in much the same way in different parts of England, and soon he was able, by looking at fossils collected by other people, to tell from what...

Jan 1, 1950

By P Blattner

The Late Miocene gold-silver bearing epithermal system at Waihi has some close similarities in its paleo-thermal and geochemical structure with modern, volcanic-hosted geothermal systems such as Ohaaki-Broadlands. At Waihi an extensive braided quartz vein system is enveloped by hydrothermally altered andesites with minor tuff breccias and tuffs. A main stage of vein filling consists of multiple phases of chalcedonic quartz and fine to medium grained quartz, which are accompanied by pyrite, sphalerite, galena, chalcopyrite and acanthite below the base of oxidation. Platy calcite is present locally. Fluid inclusion studies indicate that the main stage quartz was deposited at temperatures of 189¦-273¦C from dilute (Tm of -0.1 to -1.0¦C) fluids that were locally boiling. Homogenisation temperature Th versus Tm data points lie within the field enveloped by dilution and boiling/gas loss paths determined for the Ohaaki geothermal field, and indicates that the parent hydrothermal fluid for the Waihi epithermal system had a similar composition to that at Ohaaki, ie 0.2 wt% equiv NaCl and 3.3 wt% equiv CO2. The hydrothermal alteration mineralogy and the isotopic composition of vein calcite indicate that the hydrothermal fluid contained relatively high concentrations of CO2 , as at Ohaaki. Oxygen isotope analyses of main stage quartz range from 6.1 to 11.6 %0 and of vein calcite from 2.29 to 9.4%0. Calculated d18Owater values for the hydrothermal fluid that deposited the main stage quartz range from 2.0 to -5.7%0, with a trend to less negative values with depth. They are similar to those in the deep chloride fluid in active geothermal systems with a substantial fluid throughput. A high fluid throughput at Waihi system is also evident from the extensive high intensity hydrothermal alteration and large volume of quartz deposited in the vein system.

Jan 1, 1995

By Anja Pfennig, Thomas Böllinghaus, Marcus Wolf

During CCS components are exposed to a corrosive environment and mechanical stress which results in corrosion fatigue and is inevitably followed by the lifetime reduction of these components. The lifetime reduction of the cyclically loaded high alloyed stainless injectionpipe steel AISI 420C (X46Cr13, 1.4034) constantly exposed to highly corrosive CO2- saturated hot thermal water is demonstrated in in-situ-laboratory experiments (T = 60 °C, brine: Stuttgart Aquifer, flow rate: 30 l/h, CO2) in an environment similar to the on-shore CCS-site in the Northern German Bassin. In-situ tension-compression experiments were established simultaneously along with electrochemical measurements using a newly designed corrosion chamber in a resonant testing machine at a frequency as low as 30 – 40 Hz. In addition technical CO2 was introduced into the closed system at a rate close to 9 L/h. S-N plots, micrographic analysis and surface analysis of the fracture surface are demonstrated. X46Cr13 (surface roughness Rz = 4) reached the maximum number of cycles (12.5 x 106) at stress amplitude of 173 MPa producing a low scatter range of 1:3.5. Hydroxide and siderite layers were found on pits and crack surfaces. No typical fatigue limit exists. Pit corrosion prior to crack initiation may be identified as failure cause.

Jan 1, 2016

Project developent proceeds by increasingly detailed studies addressing overall project returns through an analysis of the substance, risks and costs associated with the following elements: ò Reserves ò Mining ò Processing ò Infrastructure ò Environmental Impact ò Product Market Computer-based expertise has a potential to ò Capture perishable expertise, making this available for shared access and so reducing the cost of human experience ò Consolidate know-how for optimising process operations, bringing consistency of judgement and advice to decision- making by making the rules, facts and preferences explicit ò Allow assignment of the basis and authority of decisions, so experts can pass routine expertise down the line, freeing their time to generate more. ò Force a review of expertise when creating the knowledge base.

Jan 1, 1989

By S. T. Kok

This paper presents a case study in West Malaysia for passive piles failure in very soft marine clay in open excavation. In this particular case, the thickness of the very soft marine clay ranges from 5 m to 7 m (16 ft to 23 ft) from the ground surface. Preliminary site investigation reported SPT ?N? value of zero for the very soft marine clay. The design was based on a deep foundation utilizing driven piles to support the superstructure. During pile cap construction, the piles were subjected to uncontrolled open excavation, inducing bending moment in the piles, resulting in some cracked and broken piles. Analyses were carried out using an existing three-dimensional finite element code with a non-linear soil model to predict the response of these piles during excavation. Finally, the predictions of pile responses during excavation were compared satisfactorily with the observed results.

Jan 1, 2009

By John Russell

"Faster, safer, grinding mill relining offers the obvious attractions of reduced mill relining times with the knock-on incentive to reduce all other maintenance down-time, opening the possibility for increased annual plant utilisation.Leading edge liner handler technologies by RME, focused toward even shorter relines for very large SAG and AG mills, have recently split into two quite distinct paths:•,?Single SAG/AG Mill Relining Machines (MRM’s) of very large capacity, such as Newcrest Cadia’s 40’ SAG MRM of 6000 kg capacity and P.T. Freeport’s 38’/34’ SAG MRM of 7250 kg capacity;•,?Twin-machine SAG/AG Mill Relining Systems of moderate to large capacity such as BHP Billiton’s Escondida Laguna Seca 38’ SAG MRM’s, each featuring 4500 kg capacity.RME, its customers noted above and their liner suppliers are providing leadership in this important annual utilisation advance.Once the 24 hour mill shell reline becomes reality, liners designed for maximum profit, not maximum life, albeit exchanged more frequently, become possible too.INTRODUCTIONAt most mineral grinding plants, mill relining activities dictate each maintenance shutdown’s critical path. When annualized, mill relining remains the largest, single influence in defining plant availability.Because of restricted access, both inside and outside the mill, increased application of manual labour has no effect on reducing relining downtime. The only answer for RME has been to develop and apply new relining technologies now known as RME’s Mill Relining System.RME’s primary focus for over twenty years has been the reduction of grinding mill relining times while simultaneously providing a marked improvement in relining safety. Our original (1990) target was to halve traditional (pre-RME) reline times and to eliminate accidents and injury by mechanizing all physical work."

Jan 1, 2008

By G J. Corbett, T M. Leach

Approximately 42 t of mercury were produced from Puhipuhi from the late nineteenth century until the end of World War II, with no significant gold or silver production. Sinter, eruption breccias and veins, mined for mercury at Puhipuhi and essentially barren of gold, are inferred in many geological models to represent the surficial levels of adularia-sericite style low sulfidation gold-silver systems. These systems may contain economic gold-silver mineralisation at depth. Conceptual geological models have been employed at Puhipuhi in the search for buried gold mineralisation. Homestake Mining utilised a McLaughlin model for exploration from 1982 to 1987, targeting mainly the vicinity of the sinter deposits. From 1987 to 1989 BHP sought deeper structurally controlled gold mineralisation within the basement greywackes, utilising models derived from studies of Round Mountain, USA and Hishikari, Japan. Macraes Mining Company Limited have accessed the previous work and applied a conceptual geological which invokes a north-south structural control for the emplacement of high-level felsic intrusions at depth. Dextral movement on these structures associated with oblique convergence facilitated the formation of a pull-apart basin in which lacustrine sediments overlie basement greywackes and are in tum overlain by Pliocene basalts. Continued activation of the NS structures created a series of inferred NE-trending dilational structures, which are targeted as fluid upflow centres for the surficial outflows. Upflows occur as eruption breccias (e.g., Plumduff) and outflow as silica sinters (eg Mt Mitchell, Williams) which are also partly obscured by the basalt cover. Argillic alteration and mercury mineralisation occur at elevated crustal levels (eg Puhipuhi mine). Modelling from structure and alteration zonations have targeted a fluid upflow in the vicinity of Bush Hill, which was not accessed by previous workers. This target was subsequently supported by surface geology and multi-element soil geochemistry.

Jan 1, 1997

By Murat Erdemoğlu, Turan Uysal, Thierno Saidou Barry, Mustafa Birinci

The rapid development of the global alumina and aluminum industry is straight coupled with the demands and the needs of these materials. Nowadays, the only well-known accessible resources to produce alumina and aluminum are bauxite ores. But bauxite ores are limited, and the remaining exploitable reserves do not have high contents in alumina. In countries where there is little or no bauxite reserves or where the recovery of existing bauxite ores to produce alumina with the Bayer process are not economic, alternative resources for alumina have been explored. The most attractive resources for replacing bauxites are aluminosilicate clay minerals and coal fly ash. The important processes developed for the recovery of alumina from these sources are acid leaching and alkaline leaching processes. The acid leaching is known as the most efficient in which thermal and mechanical activation are included for improving the performance of the process. The objective of this review is to give a comprehensive insight on the production of the alumina from thermally or mechanically activated clays and coal fly ash by hydrochloric, sulfuric, and nitric acid leaching processes.

By Güven Önal, Zeki Dogan, Neset Acarkan

In this study, it was aimed to produce glass sand with less than 0.15% Fe2O3 for window glass manufacture and glass ware grade with less than 0.05% Fe2O3 from Yalõköy sand dunes having 0.48% Fe2O3. In order to reduce the iron content of the Yalõköy sand dune, magnetic separation, flotation, scrubbing, H2SO4 leaching and drying were used. The optimum iron removal was achieved by H2SO4 baking at 150oC and 8 kg/t acid consumption. In this way, sand concentrate was obtained with 0.04% Fe2O3 and sand recovery 95%.

Jan 1, 2003

By A. C. Richardson

The mine of the Porter Coal Co. is located at the town of Porter in the northwestern part of Jefferson, County, Ala., about 20 miles west of Birmingham. The operations in this mine are confined to the middle and bottom benches of the Mary Lee bed. The coal from the Porter mine is handpicked and washed before being placed on the market. The handpicked lump coal and the washed egg and nut, coal are sold chiefly as domestic and steam-raising fuel. The coal finer than 1 inch is washed in 2-compartment jigs and utilized in the manufacture of metallurgical coke. The coal company has found that, when coal ranging in size from 1 to 0 inch is washed in jigs, a considerable amount of high-ash material finer than 3/16 inch remains in the washed coal. This paper gives the results of an investigation which was conducted for the purpose of determining the washing characteristics of the through 316-inch raw coal and the extent to which the ash might be reduced by means of coal-washing tables. This investigation has been made in connection with an. extensive study of the coal-washing problems now being conducted by the United States Bureau of Mines and the University of Alabama, with the cooperation of the coal-mining companies of the State.

Jan 1, 1933

By R. Marrill

Mining is a complex and intensive industry. Extracting raw material with different shapes, sizes, chemistry from the earth?s crust and transform them into a standardized and high quality final product is a big processing challenge - which involves energy and control on large scales. Not only is the physical work challenging, the mining industry today is facing unprecedented challenges: Decline of mineral grade and reserves, cost escalation for new developments and modernization, regulations, safety, lack of skilled people, and market uncertainty are the new constant. It is clear that process control and management of electrical power will be of increasing importance to the recovery rates the mine will achieve. The objective of this paper is to provide a quick vision about future trends and evolutions in technology related to these fields and their impact on Electrical Safety and Control of the mineral recovery. The paper will cover trends in safety, energy management and efficiency, communications of data, control room evolutions, plant integration, other control technologies, and we will examine how these technologies provide information and the benefits of aligned reporting systems to address current industry challenges. More than just the trends or breakthrough concepts, current technologies are available today that can be applied in the mineral recovery operations now to help overcome anticipated future challenges will be presented later in this document. Finally, a brief discussion to look at some real tools to help make real time changes to the process while maximizing recovery and optimizing cost.

Feb 27, 2013

By Umay Cinarli, Ahmet Turan

High-energy consumption in primary aluminum production (from bauxite ores) makes secondary aluminum production (from metallic raw materials such as scrap and dross) very critical. Aluminum dross, as a waste, arises in pyrometallurgical processes, and it is the mixture of metallic Al, Al2O3, other metal oxides, metal halides, and some other compounds like AlN. Aluminum dross has two subgroups (white and black) with respect to its metallic aluminum content. White dross is a secondary aluminum resource because of its high metallic aluminum content, whereas black dross, having low metallic aluminum content, is generally disposed in dumping areas. In the present study, it was aimed to develop a simple technique to valorize aluminum black dross in the form of alumina-based ceramic materials through pyrometallurgical (calcination) and hydrometallurgical (leaching) operations. Moreover, thermochemical simulations were conducted by using HSC Chemistry 6.12 software to simulate calcination conditions. After leaching experiments, an alumina-based ceramic containing approximately 36.8% Al2O3, 61.4% MgAl2O4 with 1.8% Na2FeO4, which might be available to use as a spinel refractory in steel smelting furnaces, was obtained in the experiment carried out in a solution containing 10 mLH2SO4 and 40 mL distilled water (3.5 M). Moreover, the sinterability of the alumina-based ceramic was investigated at the temperatures from 1350 to 1550 °C. In the sample which was sintered at 1550 °C, a density value of 3.15 g cm−3 and a hardness value of 69.58 HV were measured.

Oct 26, 2020

By C. W. Spencer, Che-Yu Li, R. J. Knight

The usual reaction product for the monotectic reaction in the Bi-Se system consists of rod -shaped particles of selenium-rich liquid embedded in a single crystal matrix of At certain crystallo-graphic orientations of the matrix with respect to the reaction interface, more complex shapes are as -sumed by the liquid particles. This reaction has been examined at different growth rates and relative crystallographic orientations of the matrix with respect to the reaction interface. The uhriation in auerage particle size of the liquid phase with reaction rate has been determined at one crystallograpIzic orientation of the matrix. On a plot of logarithm of average particle diameter vs logarithm of reaction rate, data points for crystals grown at rates of 10- to 1.0 cm per hr fall near a curve of slobe -0.4. MONOTECTIC reactions in binary alloy systems are reactions of the eutectic class in which, as the system is cooled through the three-phase reaction isotherm, one liquid phase (L) decomposes to a solid phase and another liquid phase (LII).' A partial phase diagram, as taken from Hansen, showing the monotectic reaction in the Bi-Se system is given in Fig. 1. This diagram specifies the monotectic point at 618°C and 72 at. pct Se, and the monotectic reaction products as the intermetallic Bi Se3 and a liquid (LII) which contains approximately 98 at. pct Se. At a lower temperature, 217°C, this liquid may undergo a eutectic reaction in which the reaction products are BizSe3 and crystalline selenium. However, under conditions of rapid cooling, or quenching, from above 217°C, this selenium-rich liquid may be partially retained to room temperature in an amorphous or glassy state. The intermetallic BizSe3 is rhombohedral, of the space group jm;' however, for convenience it is usually represented by a hexagonal struture. A pronounced plane of cleavage, which lies perpendicular to the main axis of the rhombohedral unit cell or parallel to the basal plane of the hexagonal cell, exists in the structure. The usual monotectic reaction product consists of rod-like particles of LII embedded in a single-crystal matrix of BizSe3, although at certain crystallographic orientations of the matrix BizSe3 other more complex shapes are assumed by LII. A similar rod-like, or cylindrical, morphology for the carbide phase has been reported by westbrook7 in the a Cr-Crz3Ce eutectic structure. In this paper the morphological characteristics of the LII particles, as retained to room temperature, have been examined under conditions of varying growth rate and crystallographic orientation of the matrix BizSe3 with respect to the growth direction. EXPERIMENTAL PROCEDURE Alloy specimens corresponding to the monotectic composition, 72 at. pct, or 50 w pct Se, were prepared from 99.999 pct pure bismuth and selenium obtained from the American Smelting and Refining Co. The two elements, corresponding to a total specimen weight of approximately 30 g, were encapsulated in 13 mm OD Vycor tubing under a vacuum of 5 x X mm of Hg. The capsules were suspended on a fine platinum wire in a Bridgman-type furnace which exhibited a temperature gradient of

Jan 1, 1963

By Phillip J. Maddex

Transportation is a major part of yours in the industrial minerals industry. Whereas federal income taxes merely take 50 per cent of your firms profits, transportation cost may take 50 per cent of the gross realization - selling price plus transportation - on your product, f. o. b. customers plant.

Jan 1, 1969