Search Documents

By W. M. Dressel

In producing feed for a lead blast furnace, concentrates analyzing 70 to 80 pct Pb are sintered to produce a physically acceptable low-sulfur product which contains only about 50 pct Pb. Mixtures of PbS with varying amounts of SiO2, CaO, Fe 20., and ZnS were heated in an oxidizing atmosphere at 1,000° C; the products were cooled and examined to determine the problems involved in producing sinter with substantially higher lead levels. Microscopic and electron microprobe studies of the above products as well as experimental and commercial sinters indicate that sinters consist essentially of lead silicates, lead-zinc silicate, calcium zinc silicate, and spinel (ferrite). Lead oxide and lead sulfate areas appear to result from insufficient mixing of the materials prior to sintering. The data give an insight into the process and show that sintering results from a complex interaction of all constituents and that sintering is not simply a matter of diluting the mixture to control the oxidation of lead sulfide.

Jan 1, 1975

By E. M. Cohn

The literature dealing with the electrical conductivity of solid dielectrics, including all its aspects and its relationships to other physical properties of these materials, is extensive and scattered in many books, phamphlets, and periodicals. It is believed that most of the important contributions to this field up to October 1943 have been listed and abstracted in this circular. Also included are some general references on static electricity. Methods of removing static charges are described; methods of and conditions for measurements of resistivity are discussed; equations for the calculation of resistivity are given; and methods of resistance measurements in Situ are reviewed. Data on the variations of resistivity with changing conditions as well as explanations for them have been collected, and three tables showing the resistivity of various dielectrics at different humidities are included. The appendix contains a short development of the mathematical formulation of the charging and discharging currents due to interfacial polarisation. INTRODUCTION Methods for Removing Static Electricity Of the various means employed for preventing or removing accumulations of static electricity in industrial processes, grounding is the most common and most generally effective. It is a precaution readily applied to stationary machines anti may often be utilized to good advantage to rid persons and portable equipment of an acquired charge. There are many situations, however, in which direct low-resistance grounding cannot be used, either because the charged bodies are insulators or are inaccessible, or because contact to a ground lead might give rise to a hazardous spark. If the charged body is a conductor, contact made to a neighboring conductor, even though the latter be insulated from ground and of relatively small capacitance, may also result in the occurrence of an incendive spark. In such instances, static electricity can sometimes be removed most satisfactorily by means of strong atmospheric ionization produced by radioactive material, X-rays, ultraviolet light, or A. C. high-voltage brush discharge. Where no danger exists from flammable

Jan 1, 1944

By Ali Ameli

Design loads are limited for piles relying upon toe stresses in rock due to uncertainty about the rock quality over the whole pile diameter because of rock mass properties or construction effects. The paper discusses the use of video images to evaluate rock quality at the bottom of piles socketed into graniodorite bedrock in a steel pipe pile project. Skillful interpretation was required to assess the 3D properties of the rock from video images. It is necessary to observe the rock mass characteristics near the project site for better perception of the rock features from the images. Video image interpretation skills were established by the evaluation of the cores drilled under the socket base and the results of pile loading tests. Correlations were found between rock appearance in the images and the rock socket drilling records. Rock socket acceptance criteria were developed through monitoring the drilling operations for the specific site procedures. Video images then served as one of the quality-assurance tools together with probing and pile loading test. Lessons and methods learned from video inspection in this project could be used to evaluate rock quality in similar cases.

Jan 1, 2006

By Wenjun Ju, Xiaodong Sun, Jianwei Zheng, Bingding Yi, Zhaorui Ma, Pengfei Jiang, Lingfu Zhu, Yangfa Zheng

The presence of hard roof poses a significant threat to the safety of underground coal mining. In this study, a mechanical model is established for underground stopes to analyze the overburden structure with the advancing of the mining face. It is indicated that the load-bearing arch structure (LBAS) is formed above the stope for roofs with regular hardness, whereas the reversed-basin bearing structure (RBBS) is formed for hard roofs. Compared with the LBAS, the RBBS can induce an additional pressure at the foot of the bearing structure, and this effect becomes less as the distance between the hard roof and stope increases. The ultra-deep borehole hydro-fracturing technique (UHT) is proposed to weaken the hard roof for pressure release, and the associated equipment and procedures are also presented. The UHT is based on horizontal drilling along the axial direction of the roadway in the roof, and then the receding segmented hydraulic fracturing technique is used to achieve the purpose of fracturing (weakening) of the surrounding rocks. Field tests are carried out in 3022 roadway of Daliangwan coal mine in Yulin to assess the developed technique, equipment, and fracturing procedures. To evaluate the fracturing effect, deep borehole stress-meters are installed at different depths of the fractured and un-fractured zones of the roadway, along with hydraulic support pressure sensors placed at the mining face. The results show that compared with the un-fractured zone, the pressure on the wall and pillar sides is lower than that in the fractured zone, and the associated weighting duration and weighting area ratio of the fractured are reduced by 53.23% and 33.59%, respectively. This indicates that the presented UHT can provide a new solution for the prevention and control of mining disasters induced by hard roof failures in underground coal mining.

Nov 2, 2020

By Y. Jin

Magnesia ramming materials have been widely used in China instead of magnesia bricks as furnace lining materials of ferroalloy refining furnace. The paper introduces the development of the ramming material, recounts its chemical composition, physical property and application characteristics. Because of its high MgO contents and fine sintering property, the ramming furnace bottom has the properties of good refractory, monolithic construction and thermal shock resistance. The changes in mineral composition and furnace tearout characterization show the reasons for the bottom?s long service life. The obvious benefits are widely achieved, the annual saving cost in refractory is about 2 millions US dollars.

Jan 1, 2004

By A. J. Kauffman

This inventory of the industrial mineral resources of the Pacific Northwest indicates that each of the States comprising this great region annually produces nonmetallic materials valued at mans million dollars. Commodities or their products that have a large, localized market predominate. These include Portland cement, sand and gravel, stone, clay, and lime. The region's output of magnesite, vermiculite, pumice, and diatomaceous earth is outstanding. The magnesite deposits of Stevens County, Wash., are the largest and most important in this country. Mast of the domestic vermiculite production is obtained from deposits in Lincoln County, Mont. Oregon and Idaho rank third and fourth, respectively, as domestic pumice producers. Production data for diatomaceous earth show Oregon second and Washington fourth among the producing States.

Jan 1, 1952

This report summarizes the results of a research project entitled "Fatal Accident Data Base Development." This project is the last project under Contract No. S0110601. Volumes I and 1I, "Industrial Engineering Study of Hazards Associated with Underground Coat Mine Production," summarize the original industrial engineering project and the Fatal Accident Report Analysis project. These projects were completed and accepted by the U.S. Bureau of Mines on December 10, 1971. Both volumes of the report have been made available by the Bureau to the public through the U. S. Department of Commerce technical information service. Another project under the same con tract, entitled "Equipment Operations Safety Study, ' was completed in January 1972 and the report was accepted by the U. S. B. M. at that time. The analysis in this Natal Accident. Data Lose Development report is closely related to analysis in both of the earlier reports. The original project involved an industrial engineering and safety of production operations for a representative sample of underground bituminous coal mines. The contactor was required to make recommendations 'in work practices, mining methods, equipment, and safety practices which can effectively reduce the fatality rate from rib and roof falls.' (Longwall mining methods were excluded from the study.) Time study and work element analyses were performed in over 50 mines as part of the field data gathering effort. Another requirement of the study was to develop sets of multiflow. Process charts, which are diagrammatic illustrations of the time-related interaction of mining, cycle job elements.

Jan 1, 1972

By Eduardo Luiz Sales Marinho

A Fábrica de oxigênio da AMT produz gases O2 e N2, utilizados no processo de produção de aço. Neste processo de fracionamento de ar, existe um compressor de ar que é responsável pela captação do ar atmosférico. Este compressor é do tipo centrifugo de 4º estágios de compressão, fabricação Hitachi, e tem capacidades de vazão de 114.000 Nm³/h e pressão de descarga 5.4 Kg/cm². Em Novembro de 2012, foi realizada inspeção no compressor e identificado trincas nas pás do impelidor do 4º st e perda de espessura de parede das pás do impelidor do 3º st de compressão. Houve perda da confiabilidade de operação do equipamento, sendo necessária uma ação para correção do problema. Depois de identificado a causa raiz das trincas,foi decidida a compra de dois novos impelidores com modificações no material para aumentar a resistência à corrosão. Na aquisição dos novos impelidores havia duas possibilidades: 1) Adquirir novos impelidores junto ao fabricante original do equipamento; 2) Adquirir novos impelidores por processo de engenharia reversa (levantamento de desenhos da peça desgastada para fabricação de uma nova) em conjunto junto com empresa especializada. Este trabalho irá mostrar os critérios e considerações que levaram a AMT decidir pela compra de novos impelidores por “Engenharia Reversa”, bem como, suas vantagens e riscos assumidos.

Sep 25, 2017

The paper outlines the development of a solvent extraction process for the recovery of scandium, yttrium, thorium, and heavy lanthanides from waste sulphate liquor at the Port Pirie uranium treatment plant. A summary is given of known solvents for these elements, including the recently developed alkyl-phosphoric acid esters which are applicable to sulphate solutions.A kerosene solution of di- (2'-ethylhexyl) phosphoric acid (EHPA) has been suggested by some workers as a suitable solvent for fractionation of the lanthanides. Experimental work with this solvent showed that it could be used for initial recovery of the above elements from low concentrations in the complex sulphate liquor. In particular, scandium could be recovered as a high grade product by extraction with 0·lM EHPA, followed by a purification strip with 9N sulphuric acid, and final stripping of scandium with sodium hydroxide solution.To enable alkaline stripping to be used successfully, the kerosene solution of the reagent was modified by the addition of a small proportion of nonanol. Experimental work included laboratory scale batch tests and small pilot scale continuous tests.A proposed extension of the process for the separate recovery of individual heavy lanthanides, yttrium, and thorium is described.INTRODUCTIONAt the Port Pirie uranium treatment plant of the South Australian Government, large volumes of "barren liquor", free from 'uranium, are at present run to waste. This "barren liquor" results from sulphuric acid leaching of Radium,Hill uranium concentrate, followed by separation of solid residues and removal of uranium from the clear solution by ion exchange. The mineral davidite, from which the uranium is derived, contains other potentially valuable components, notably vanadium, chromium, thorium, yttrium, scandium, and the lanthanides. These constituents are...

Jan 1, 1961

By Tom Ireland, Tony Rock

The proposed 1.83km long twin bore A3 Hindhead road tunnel planned for contruction in 2008 is being delivered under a Highways Agency Early Contractor Involvement (ECI) contract. The proposed construction methodology is progressive mechanical excavation of a horseshoe shaped tunnel with shotcrete installed close behind the face using robotic spraying equipment. The tunneling medium is a ‘soft rock’ sandstone for which there was little previous tunneling experience, requiring extensive geotechnical investigations and an innovative approach to lining design. A 240m long portal section though sandy material utilising a steel pipe umbrella is also required. This paper describes the development of the tunnel planning and design including the most recent developments in UK road tunnels, and the innovation included in the ‘permanent’ primary lining design.

Jan 1, 2007

By Fred C. Schmednecht

For years, the strategy was to contain waste and in many applications, is still the recommended method. Recently, it has become acceptable to create filters below ground for the in-situ treatment of waste. Consequently, in lieu of the waste being contained, it is desirable that the waste flow through a pervious treatment zone. For instance, subterranean pervious walls comprised of iron sand are particularly useful in treating chlorinated solvents in contaminated groundwater. The iron acts as a corrective filter to treat the contaminated groundwater. How are these impervious and pervious walls being constructed? One effective means of constructing an impervious barrier is the vibrated beam method. This method, in brief, involves the use of a fabricated steel beam, a vibrator, a pile driving crane, and a mixing plant. This method results in a 4-6" wide wall with depths up to and exceeding 100'. Over one hundred slurry walls have been installed using this method in the United States. The need for the vibrated beam method continues to escalate due to its reduced health and safety considerations, high level of quality control, lack of excavation, narrow working area, and ability to achieve depths greater than 100'. A recent project was in Marinette, Wisconsin at the ANSUL facility. The project consisted of a 28,000 square foot slurry wall and was completed in January of 1999. Another effective means of creating an impervious barrier, where structural support from the barrier is needed, is the Waterloo® Barrier System. This system involves the use of a pile driving crane, Waterloo® steel sheet piles which are patented steel sheet piles due to their groutable interlocks, and a grout plant. This system results in a water-tight barrier due to the grouted interlocks and provides structural support. A project was completed at Beta Steel in Portage, IN for a retention pond to protect Lake Michigan. Due to the new concept of "filtering", there are few accepted construction techniques available. One effective field proven construction technique is the patent pending mandrel emplacement technique. This technique involves the use of a fabricated hollow steel mandrel with a shoe, a vibrator, a heavy duty crane, and a material feeder. This technique results in a pervious wall which may be comprised of pure iron sand or any other flowable media. Using this technique, the pervious wall may be constructed in varying widths to depths in excess of 100'. A successful installation occurred in October 1997 at Cape Canaveral Air Station in Florida.

Jan 1, 1999

By Charles E. Whieldon

Because of the importance of recovering more oil from known petroleum reserves, increased emphasis has been placed on the application of secondary-recovery methods. It is hoped that these reports will stimulate interest in improved waterflooding techniques, thereby discouraging premature abandonment of oil leases. Previously published reports3 4 5/ have described the results of water-flooding in Roane, Pleasants, and Wetzel Counties, W. Va. (fig. 1). This report describes the South Penn Oil Co. Yawkey waterflood property, Berea sand, Griffithsville oilfield, Duval District, Lincoln County, W. Va. (fig. 2).

Jan 1, 1961

By J. B. Cheatham, M. D. Biggs

This paper presents a systematic method for determining the forces on a simplified roller bit. The kinematics of an actual roller bit drilling in rock is complex; nevertheless, it is desirable to obtain an accurate analytical model.. As a preliminary study, the roller bit is represented here by a simple two-dimensional bit and the rock by a Coulomb plastic material. Results from previous work, plus additional assumptions, are incorporated into a computer program to determine the forces required to move the bit in a specified manner. Example problems are worked by use of this program. By studying similar drilling problems and by supporting laboratory work, one could eventually obtain an accurate analytical model for drilling by an actual roller bit. This could lead to the compilation of a catalog of results that, in turn, would allow selection of the optimum drill bit for any given situation. INTRODUCTION

Jan 1, 1970

By R. F. Abernethy

Recent investigations in the United States and in other countries have produced considerable information on the nature and occurrence of minor elements in coal. The possibility of recovering certain elements, particularly germanium and uranium, from coal ash and other coal products has received considerable attention. Some flue dusts are potential sources of germanium, and certain lignite deposits are potential sources of uranium, but industrial recovery of these elements has been limited to small quantities for technical and economic reasons. Considering the large amount of coal mined annually, a small percentage of a rare element may have industrial significance if an economical method of recovery can be developed. In 1944 information on the occurrence of rare elements in coal was reviewed in Bureau of Mines Technical Paper 669 (46).3 This report is a revision of that paper with the view of summarizing published information available for United States coals, and pertinent information concerning coals of other countries. Selected references from the original paper are retained. New references do not include all preliminary reports when more permanent literature describing complete projects is available. Consequently, the list of references should not be considered complete.

Jan 1, 1963

By Y. Nakamura, T. H. Okabe, S. A. Sunkar, K. Nose

Ruthenium (Ru) is known as a platinum group element with a very small production volume. In fact, the worldwide annual production of primary Ru metal is only about 20-30 tons, and it depends on the amount of Pt produced, since Ru is a byproduct from Pt smelting. The primary uses of Ru are as a material for resistors, as a catalyst for electrode materials, and as a sputtering target for hard disk memory storage. In order to recover Ru from the spent sand-blasting abrasive media generated during the cleaning of the apparatus used for Ru sputtering, a hydrometallurgical recovery process using hypochlorite solution has been investigated. In this study, various types of recycling processes that are presently under development are also introduced, and their features and differences are discussed. The advantages and disadvantages of the new recycling processes are evaluated, and the possibility of establishing new recycling processes in the future is discussed from a multilateral perspective.

Jan 1, 2014

By G. R. Webber

CHEMICAL AN AL YSIS by x-ray emission spectrometry has become increasingly important during the past few years. The method is analogous to optical spectrography ?with x-rays being used instead of light and should not be confused with methods of x-ray diffraction used? for identification of minerals and chemical compounds. X-ray emission spectrometry has many advantages for both qualitative and quantitative analysis. Its optimum concentration range is higher than that of the optical spectrograph, and the group of elements which can be detected is not identical to that which can be detected by the optical spectrograph. Elements which can be detected by the x-ray spectrometer are those elements from magnesium (atomic number 12) to uranium (atomic number 92) in the periodic table. The lightest elements in this range have low sensitivities and more specialized equipment is necessary for their detection than for the heavier elements. A large number of applications of x-ray analysis have been directed toward the analysis of ores, metallurgical products, and related materials (see References at end of paper). A more complete bibliography is presented in the Norelco Reporter, Vol. 3, 1956, pp. 37-39. The periodicals Analytical Chemistry and Applied Spectroscopy are a good source of current articles and references.

Jan 1, 1957

By D. Marcotte, R. V. Dutaut

"In mineral resource evaluations, geostatistical methods known as global change of support allow prediction of the theoretical histogram and gradetonnage curves prior to interpolations or simulations of grades. Two methods commonly used by professionals to guide the choice of interpolation parameters and assess results are the discrete Gaussian model (DGM) and the indirect lognormal correction (IndLog). These models rely upon an estimate of the dispersion variance of the blocks, which is derived by numerical integration of the variogram model over a discretized block. Due to difficulties in obtaining well-formed traditional experimental variograms (especially in the presence of outliers and limited clustered data), many professionals prefer to use ‘normalized’ variograms such as correlogram (non-ergodic variogram), pairwise-relative, or variogram of the normal score transform. A series of simulations with different grade distributions and variogram models are used to assess the performances and robustness of the various variogram estimators with respect to the DGM and IndLog global change of support. Our results show that the traditional variogram, the correlogram, and normal score variogram have better performances, compared to pairwise, for both DGM and IndLog. Moreover, DGM provided better results than IndLog for the grade distributions that are not strictly lognormal. These findings provide valuable guides for geostatistics practitioners. IntroductionWhen reporting resource estimates,practitioners are required to follow generalstandards described in the NI43-101 (CIMguidelines), JORC, or SAMREC codes. One cangenerally recognize three main parts directlyrelated to the block model:•,Pre-processing: exploratory data analysis (EDA), domaining, capping, compositing, declustering, variography•,Processing: block size, neighbourhood, interpolation types (linear or nonlinear)•,Post-processing: classification, reporting.Pre-processing aims to simplify and strengthen the processing step. Ideally, domaining, capping. and compositing is aimed at defining a single homogenous population. During the processing phase, a common practice is to use a block size corresponding to the planned selective mining unit (SMU). In most precious metal deposits (gold, notably), the SMU size is frequently smaller than the recommended half data spacing (Journel and Huijbregts 1978), resulting in high estimation variance and either a high degree of smoothing if the regression slope is managed or a high degree of conditional bias if it is not. Most actual resource estimates are made using block sizes between one-quarter to one-sixth of the average data spacing, sometimes even smaller. In addition to the block size, the interpolation choices for the neighbourhood selection and interpolator (e.g. inverse distance (ID) or ordinary kriging) are often based on the Qualified Person’s (the QP) experience and some basic validation plots that often do not consider the conditional bias (e.g. trends or SWATHs plots, which are designed to compare two sets of population using a one-dimensional graph)."

Jan 1, 2018

By Franz Kolmbauer

At Primetals Technologies Brazil Ltda. Rio de Janeiro Santa Cruz Workshop we electroplate mold coppers for continuous casting by tank plating. Tank plating submerges the copper in the bath of the plating solution. This is the most common method of plating and is applicable for both broadface and narrowface copper plates. Mold copper plates have a decisive impact on the product quality as well as the cost for maintenance and production. A perfect understanding of the operational influences on the plates and performance variables are the first step for the right selection of a copper plating method. Variable Hiper Coat keeps the Copper Plates 50% up to 100% longer in operation because of applying hardness on the Copper Plate where it is needed. Primetals Technologies Brazil provides the solution which meets and exceeds the requirements for todays and future demands.

Aug 16, 2017

By Cardm Jeffrey W.

The decay of 222 Rn yields a series of short-lived decay products which become attached to the surface of a plate or wire exposed in a 222Rn-bearing atmosphere. The alpha-activity of two of the decay products, 218Po and 214Po, can be measured by simple counting techniques. This phenomenon may have direct application to uranium exploration. Laboratory studies have shown that: (a) radon decay products can be collected on a wide variety of materials (including various kinds of metals and plastics); (b) activity increases as a function of the surface area of the 'collector; and (c) the collection of the decay products is enhanced by applying a negative charge. The new technique was used in situ to delineate the anomaly above the South March uranium-copper occurrence. A related technique was developed to measure radium in soil samples. The results of both studies compared favourably with those obtained from conventional methods.

Jan 1, 1979

By R. F. Lynch, F. E. Goodwin, A. F. Skenazi

"The Gal/an alloy has been developed for continuous galvanizing of steel. The choice of the eutectic zinc-aluminum alloy with addition of misch metal gives a coating with specific characteristics as far as structure, analysis, surface chemistry and surface morphology are concerned. The performance of the uncoated Galfan coating is superior when compared to conventional galvanized particularly for corrosion resistance and ductility. For coil coating applications, these two assets are of the utmost importance but in order to benefit from these two advantages, good paint adherence and high resistance to edge creep and blistering have to be obtained. Despite Galfan's unique features compared to other zinc based or aluminum zinc based coatings, existing pretreatments and painting conditions are used with only minor modifications in order to assure good adherence and edge creep resistance. With compatible processing, Galfan can outperform galvanized and Galvalume as a substrate for coil coating as is demonstrated with various test results.IntroductionThe technical and commercial development of Galfan, a 95% zinc-5% aluminum-0.1% lanthanum-cerium hot-dip coating for steel, has been rapid. From its identification as a promising coating in late 1980, it has evolved from a research product to a fully commercial product with over 100 000 metric tons of coated sheet produced to date, and another 90 000 tons, at minimum, scheduled for 1986. The great majority of tonnage produced to date has been coil coated for use in building panel , appliance, and similar applications. Much technical work has been done to determine the suitability of Galfan for these applications and the proper way of processing sheet for best results. The present state of knowledge is discussed in this paper, along with some recent applications which are given asexamples"

Jan 1, 1987