Search Documents

By J. R. Evans

Mining claims must have a discovery of a valuable mineral deposit to be valid. When required, a Federal government mineral examiner makes a determination of validity and recommendations thereof to authorized management officials. The examiner should show whether or not an existing mining operation, or a proposed operation have economic viability. This is accomplished through an analysis of legal entities, land status and use, geologic and mineralogic relationships, and mining, milling and processing techniques considered in an appropriate economic evaluation framework. A framework involves market and market entry studies, reserve analyses, all costs analysis, royalty buyouts, tax structure, discount rate of return, and escalation and risk factors. An income approach to value is then used by means of a simple or complex discounted cash flow (DCF) analysis to certify validity. Whether one claim is owned by a single miner, or hundreds of claims are owned by a large corporation, thorough, fair, consistent, and appropriate economic concepts should be applied by the mineral examiner.

Jan 1, 1993

By William R. Wayment

The objective of this investigation was to obtain data on friction-head losses of sand slurries during their transport in pipelines. The data ultimately will be used in designing hydraulic transport systems. Information that was incidental to the primary objective was gathered on degradation, changed percolation characteristics, and critical velocities of the slurries~ Tests were made in a closed-circuit pilot plant, with one type of tailing, through horizontal 2-, 3-, and 4-inch-pipe test sections at various pulp densities and flow velocities. Tests were made in a closed-circuit pilot plant, with one type of tailing, through horizontal 2-, 3-, and 4-inch-pipe test sections at various pulp densities and flow velocities. Approximately 2,000 tests were run in the pilot plant. The ranges of flow velocities used in the experiment were 2.8 to 19 f.p.s. in the 2-inch line, 4 to 14.5 f.p.s. in the 3-inch line, and 4 to 11 f.p.s. in the 4-inch line. Velocities were varied in increments of 0.5 f.p.s. through the entire velocity range in each pipe size. Densities were varied in 3-percent increments from 40 to 70 percent solids by weight except for one series of tests in the 2-inch line; in this series, densities were varied in 5-percent increments from 5 to 65 percent solids by weight.

Jan 1, 1962

By B. P. Sereda

The properties, characteristics and phase structure of chamotte refractories produced with the usage of mullitecorund chamotte and caoline have been given. The comparison of new refractory C-45 obtained by us and refractory C-43 produced by traditional method has done. The physical-chemical properties of refractories is reviewed. The visual porosity, density and pore characteristics of given refractories was calculated. It is established that C-45 has the less gas permeability then C-45 that gives melting units more stability. The petrographical microstructures of refractories have been done. The main phase structures and their influence on refractories properties have been observed. It is established that refractories with mullitecorund chamotte adition has more advantages then refractories gained by traditional method and can be applied to melting units.

Jan 1, 2010

By Chao Lian, Hongxu Li, Hao Bai, Wei Wei

"Application of high-emissivity coating on inner walls in industrial furnaces increases the furnace thermal efficiency. The coating with high emissivity strengthens radiation heat transfer in the furnace, however, according to Wien's displacement law and Planck's radiation law, under heating temperature, the wavelengths of the radiation transfer are mostly between 1-5 µm, implying that increasing emissivity of the coating in near infrared band is more effective for higher thermal efficiency. In this paper, a new CuO-ZnO-based coating material sintered at 1600K was developed. The emissivity of the samples were measured and the result shows that, in near-infrared band, the emissivity of the sample reaches 0.98 at 773K with 13at.% of CuO doped in ZnO. In addition, the effects of CuO doping and use temperature on emissivity were also discussed. Furthermore, crystallization behaviors of ZnO-CuO sintering were investigated by DTA,XRD and SEM-EDS etc., which offered information for possible optimal design of the material.1. IntroductionIndustrial furnaces are widely used in various industrial heating. For example, the metal smelting furnace, ore sintering furnace in metallurgical industry; the distillation furnace, cracking furnace in petroleum industry etc,. The research on efficient energy saving technology has important significance. High emissivity coatings are widely used in many high temperature applications to effectively transfer the heat by radiation [ 1]. The theoretical calculation and experimental studies have shown that, coated high emissivity coating in the heating surface is an effective method to enlarge the infrared radiation power [2].At present, the infrared high emissivity coating has been widely used in China, and have been achieved remarkable energy saving effect. According to Wien' s displacement law and Planck' slaw, most energy of the black body at high temperature is radiated in the wavelength range of l-5µm; however it happens that many materials have the low emissivity within this range. Thus, it is important to improve the near-infrared band emissivity of materials [3]."

Jan 1, 2013

By Doug Harding

The Niagara Tunnel Project (NTP) is a 10.4 km (6.5 mi) long, 14.4 m (47.5 ft)bored tunnel that will run under the City of Niagara Falls from the Upper Niagara River to the Sir Adam Beck Power Station. The completed project will enhance the capacity of the Sir Adam Beck Power Station by adding 500 m3 (17,657 ft3) of water per second through the tunnel. The paper describes the project in which the world’s largest hard rock TBM at14.4 m (47.5 ft) in diameter is being used to excavate the tunnel. Features of the project include the use of a High Performance (HP) Main Beam TBM, state-of-the-art ground support and tunnel logistics systems. A continuous conveyor is used for muck transport from the TBM to the disposal area. The paper will also discuss the optimization of the TBM system as the tunnel advances through the varying geology. In June 2004 the Ontario Government announced that Ontario Power Generation(OPG) had been given approval to proceed with the third tunnel under the city of Niagara Falls—the first two tunnels were constructed in the 1950s using drill and blast techniques. The third tunnel, appropriately named The Niagara Tunnel Project (NTP), consists of a 10.4 km (6.5 mi) long TBM-bored, concrete-lined tunnel with a finished diameter of 12.5 m (41.1 ft). In August 2005, OPG announced the selection of Strabag AG of Austria, one of the largest construction companies in Europe, as the contractor to build the NTP Project at a price of CAN $600 million. In September 2005, Strabag A.G. selected The Robbins Company of Solon, Ohio to design, manufacture and deliver a new 14.4 m (47.5 ft) diameter High Performance state-of-the-art Main Beam Hard Rock TBM to be used in the excavation of the tunnel. In order to meet the aggressive construction schedule as requested by OPG/Strabag, the TBM needed to be supplied as “ready to bore” within a 12 month period after the contract was awarded to Robbins.

Jan 1, 2007

By Dee Bradshaw

"Process mineralogy’ is a form of applied mineralogy which focuses on addressing problems associated with the processing of ores. ‘Mineralogy’ is the scientific study of minerals and ‘mineral processing’ is the production of concentrates from ores. ‘Process mineralogy,’ however can be defined as the practical study of minerals associated with the processing of ores, concentrates and smelter products for the development and optimisation of metallurgical flowsheets, including the waste and environmental management considerations. This hybrid discipline consists of teams that include geologists, mineralogists, samplers, mineral processors and often others, working together. The degree of cross-training, communication and trust dictates the potential capacity of the team and where an appropriate work dynamic is fostered, in which relationships flourish as much as does the ethic of technical excellence, it is possible to develop technical capabilities that surpass those of conventional teams. The world’s demand for metals is ever increasing and ore deposits available for extraction and processing are lower grade and more complex, often containing deleterious elements that require tailored treatment. Generally, in the past, the technical challenges only needed to be overcome and assessed economically to make an ore deposit viable; increasingly and in the future, a more sustainable approach including environmental and societal considerations is needed. Process mineralogical assessment is increasingly providing the critical information that stands between failure or collapse and survival or success of some mining operations. In this paper, selected case studies are used to demonstrate the valuable role of the process mineralogy tools being used to provide the platform for innovative technology development. Their common attributes are discussed and distilled, thus providing some insights and potential guidance for addressing some of the likely future challenges of the mining industry."

Jan 1, 2014

By Mônica Aline Magalhães Gurgel

Nas últimas décadas o setor siderúrgico vem desenvolvendo aços com maior valor tecnológico, surgindo assim várias classes, entre elas os aços avançados de alta resistência, onde encontra-se o aço bifásico ou “Dual Phase” (DP). Este aço é caracterizado por uma microestrutura ferrítica-martensítica, associada a uma matriz ferrítica com ilhas dispersas de martensita. Neste trabalho utilizou-se amostras de um aço baixo C e Mn, com micro adição de Nb e Mo, em desenvolvimento, onde se propôs uma avaliação da evolução microestrutural e propriedades mecânicas das amostras extraídas após a laminação a quente, a frio, seguida de recozimento intercrítico, em escala laboratorial, com auxílio de forno Mufla e um equipamento de análise termomecânica (TMA), resultando em taxas de aquecimento distintas, onde selecionou 7 temperaturas de encharque distintas e subsequente resfriamento com patamar isotérmico a 600°C por 20 minutos, onde observou-se que para esse ciclo a microestrutura com aspectos mais característicos de um DP se deu em tratamentos com temperatura de encharque entre 760 e 800°C.

Aug 17, 2017

By R A. Pax, B Cornish

Increasing the throughput of the MMG Century operation by over 25% from past practice to preserve cash flow close to the end of life of mine has revealed new throughput and load dynamic instabilities in the SAG mill causing significant time averaged loss of production. A twelve microphone array around the SAG mill (Pax, 2014) using the non-contact acoustic measurement methodology (Pax, 2011, 2012) has been used to diagnose the new dynamics. Dynamic acoustic noise signal information allows discrimination of the behaviour of the steel balls and the rock. Determination of mill load, toe and shoulder angles, water holdup, and proxies for mill load are possible.The instability was diagnosed with the help of an abnormality in the liners/lifters of the SAG mill with one row of lifters having a slightly increased in-mill life compared to the rest. The steel shoulder angle is observed to be disturbed cyclically at a rate of precisely one revolution at low throughputs of 750 t/h. However, at throughputs closer to 1100 t/h, the cyclic signal disappears indicating additional dynamics to randomise the repetitive behaviour of the mill charge. The cyclic signal has been used to operate the SAG mill with improved stability at 1100 t/h by adjusting the feed water addition rate.This paper presents and discusses these results and proposes the suggested origin of the extra dynamics. A small consistent aberration of the lifters circumferentially provides a useful detector of stable mill operation and a novel sensor for the dynamics of the internal operation of a SAG mill.CITATION:Pax, R A and Cornish, B, 2015. A novel measurement for the internal operation of a semi-autogenous mill using acoustic sensors – a case study, in Proceedings MetPlant 2015, pp 120–128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Mark Rybak

On August, 31, 2006, Tropical Storm Ernesto hit the City of Richmond, Virginia. The Battery Park area was hit particularly hard, as flooding forced an evacuation of the area. A large sinkhole collapsed a sewer line in the Battery Park area, blocking the pipe and causing more serious flooding. This case history describes the fast track design, bidding, and construction of an emergency tunnel to bypass the collapsed sewer. Innovative value engineering, tunneling and shaft sinking methods, and final lining design all contributed to the success of this project. The storm inundated Richmond, Virginia with up to twelve inches of rain in some areas causing widespread flooding and damage. One of the hardest hit areas of Richmond was Battery Park. A major trunk sewer in the Battery Park area collapsed causing local combined sewer and storm-water flooding. The collapsed sewer was an 8'-3" wide by 9'-6" high arch sewer that was constructed in the nineteen twenties and later filled over with municipal solid waste and a soil fill cap to current elevations. A sinkhole was created in the area of collapse approximately sixty feet deep and one hundred feet in diameter causing the existing arch sewer to become blocked. As a result of this blockage contaminated flood waters reached depths in low lying areas in excess of twenty five feet. [ ]

Jan 1, 2008

By P. Turcotte, E. Karampinos, F. Mercier-Langevin

In some underground hard-rock mines, squeezing compressive ground conditions are influenced by the presence of rock foliation and high stress. In these cases, the orientation of the foliation with respect to the drift direction has a considerable impact on the magnitude of the resulting deformation. Irrespective of the reinforcement and support strategy, keeping drives developed sub-parallel to the rock foliation operational is difficult, and often requires excessive rehabilitation during the lifetime of the excavation. This study uses field observations and convergence measurements at the LaRonde and Lapa mines of Agnico Eagle Mines Ltd to provide guidelines of the anticipated squeezing levels at these operations.

Jan 1, 2015

By Mike Amick

As virgin coal reserves dwindle, more and more mines are being opened in areas with previous mining. As addressed in this conference before, there are solutions available for designing mines extracting coal from reserves with known underground workings above or below the target seam. Often times, however, mining begins with limited knowledge of the underground workings. Even with careful planning, the proposed design has limited success because the ?facts? as presented during planning turn out not to be as accurate as one would like. At National Coal?s Mine #14, mining the Walnut Mountain seam, after driving the main entries in some 34 crosscuts, it was found during routine mine examinations that the pillars had separated from the roof in a few areas of the mains. Immediate roof conditions proved to be sound but questions arose concerning the stability of the main roof and floor. Core tests were done to better determine the rock strengths and characteristics. The paper presents the ideology used to tackle the effects of mining over old works in an operating coal mine. This paper discusses the analysis of the symptoms observed and the steps taken to ensure that this pillar separation was caused by the underlying old workings and that the separation was expected and controllable.

Jan 1, 2009

By G. Plenge, M. Diaz

Silver-bearing, bulk sulfide concentrates from several Peruvian mines were autoclaved in a l9-L (5gal) laboratory autoclave in Lima, Peru. Cyanidation of autoclaved concentrates, following a hot lime jarosite destruction step, extracted more than 98% of the silver and more than 95% of the gold. Autoclave operating parameters, such as time, temperature, pulp density and autoclaved solids recycle, were investigated and reaction rates determined. The problems of excessive heat generation, silver solubility during autoclaving and formation of pellets containing unreacted sulfides were addressed. The data presented will be used to design a continuous autoclave pilot plant to provide reliable scale-up data for a 50 to 100 t/d (55 to 110 stpd) facility.

Jan 1, 1994

The ore treatment expansion programme at Mount Isa Mines required the erection of a new lead-zinc concentrator to be known as No. 2 Concentrator. This concentrator was designed by Western-Knapp Engineering Company in conjunction with staff of Mount Isa Mines Limited. Metallurgical design followed conventional wet milling practice, but the size of many plant units is larger than previously used at Mount Isa. The. total capacity of the new plant is 150,000 tons per four weekly period, and the plant is designed to operate in two equal parallel sections.Erection was contracted on a turnkey basis, and the plant was commissioned as a production unit on 23rd June 1966.The existing concentrator, No. I, was converted to treat all copper ore, and the total capacity of the two plants is now 390,000 tons per four weekly period.

Jan 1, 1968

By B. J. Moore

This publication contains routine analyses and related source data for 528 natural gas samples from 21 States collected during calendar year 1965 as part of a continuous survey of the United States for occurrences of helium in natural gas. This survey has been conducted by the' Bureau of Mines since 1917. The analysis published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4863 and 576.4

Jan 1, 1966

By B. J. Moore

This publication contains routine analyses and related source data for 528 natural gas samples from 21 States collected during calendar year 1965 as part of a continuous survey of the United States for occurrences of helium in natural gas. This survey has been conducted by the Bureau of Mines since 1917. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4863 and 576.4

Jan 1, 1966

By Ke Yang

"Engineering practices have shown that the skip-fault longwall mining is frequently used when faults with offsets larger than 1 Om are present. Since the skip-fault longwall mining not only reduces the recovery rate of coal reserves, but also increases the cost due to developing another setup room on the opposite side of the fault and moves the longwall into it. The coal pillar so created induced residual stress in and thus affects the safe mining of adjacent coal seams. In order to investigate the influence on panel layout and retreat by a l 6.5m offset normal fault, the similar material simulation model was constructed based on the geological and engineering conditions of No.13 coal seam in the western district of Liuzhuang coal mine employing the down-dip longwall mining. The characteristics of deformation, movement and failure of the overlying strata and abutment pressure when the face cut through the hangingwall and footwall of a normal fault were obtained. There were significant differences between the hangingwall and footwall as conformed by the equilibrium structure model. The results showed that superposition of the tectonic stress from a normal fault of large offset and that induced by mining is one of key factors that lead the severe pressure difficult to control during panel retreating from the hangingwall to footwall. Accordingly, the technical solutions for a fully mechanized mining face directly cutting through the fault are presented and optimized, and the applications of the technical solution in Panels 171301and171303 of Liuzhuang mine enabled them to complete the mining safely and efficiently. INTRODUCTIONFaults have been one of the important technical factors in underground coal mining l1-2i. Engineering practice has shown that the methods of mining through the faults depend on the seam thickness, seam dip angle, offset of fault throw, equipment height, rock strength, and advancing direction l3-5l. In the fully-mechanized longwall mining, the face normally proceeds to cut through the fault directly if the offset of the fault less than 5m, and to skip Uump) the fault if the offset is larger than 5m. In the former case, the most important problem is to efficiently control or avoid roof fall accidents (i.e., crushing, falling, pushover, and rock burst). In the latter case, the most important problem is very expensive to drive a new setup room and move the face equipment to it. The skipped coal pillar may poses problems for mining in adjacent seams."

Jan 1, 2016

By Juliana Porto Guimarães

A crescente demanda por aços galvanizados com alta lubricidade tem impulsionado o desenvolvimento de pós-tratamentos que, aplicados sobre a superfície dos revestimentos, reduzem o atrito entre o ferramental e a chapa durante o processo de estampagem de peças críticas na indústria automotiva. Diante disso, a Usiminas desenvolveu, em parceria com a Quaker, a aplicação do pós-tratamento tipo microfosfato denominado Primecoat Z Auto, com a função de melhorar a estampabilidade de aços galvanizados a quente do tipo GI (Zn puro). Nesse estudo foi avaliada a Razão Limite de Estampagem (RLE) de um aço GI destinado a produção de peças críticas, após aplicação desse pós-tratamento em escala de laboratório. Adicionalmente, foram caracterizadas a morfologia e a constituição química do microfosfato, e o desempenho do aço quanto à fosfatização, à pintura automotiva e à resistência a corrosão. Concluiu-se que o filme de pós-tratamento é amorfo, constituído por Zn, P, Al e Mg, promovendo um excelente ganho de lubricidade ao aço GI, sem interferir nos processos subsequentes de fosfatização e de pintura nas montadoras. Além disso, o material apresentou excelente desempenho quanto à resistência à corrosão.

Jul 30, 2018

By Douglas A. Anderson

Mine the Internet? You bet. Precious information resources are there to be found by those willing to explore. Of course, the stratigraphy and the exploration tools must be learned. This article is is designed to help learn those tools and how to find the information that can help the reader. However, beware the Internet. It can be addicting. On the other hand, information can be found that you never suspected. And users can make contact with people who might otherwise never have crossed their paths.

Jan 1, 1996

By John W. Wagner, Robert K. Willardson

Single crystals of Pbl-xSnxTe have been grown from nonstoichiometric, cation-rich melts with the objective of producing as-grown, bulk material containing carrier concentrations ranging from 1016 per cu cm to 1018 per cu cm. Three specific crystal composi-tions were investigated in detail; x = 0.00, 0.10, and 0.17. Pull rates of from I to 3 mm per hr were used. Single crystals were successfully pulled from melts containing as little as 30 at. pct Te. Hall coefficients, resistivities, and carrier mobilities of these materials were determined. The relationship between the composition of the melt and the carrier concentration in the as-grown crystal has been studied for the three crystal compositions of interest. BULK single crystals of Pb,-,Sn,Te have previously been grown from stoichiometric melts.1,2 Such crystals are p-type and have relatively high carrier concentrations ranging from -9 x 1018 per cu cm for PbTe to -8 x l020 per cu cm for SnTe at 77°K. These carrier concentrations result from deviations from stoichiometry (lead vacancies) in the as-grown crystals. Since lower carrier concentrations are desirable for electrooptic device applications, these crystals are usually subjected to long-term, isothermal anneals.' This paper reports on the growth of Pbl-xSnxTe single crystals from nonstoichiometric melts with the primary objective of producing as-grown material containing relatively low (1016 to 1018 per cu cm) carrier concentrations and also reports on the general characteristics of these crystals. The phase relationships in the Pbl-xSnxTe systems are such that materials solidifying from nonstoichiometric, cation-rich melts will have smaller deviations from stoichiometry than materials grown from stoichiometric melts. Fig. 1 is the T-x phase diagram for PbTe in the vicinity of the stoichiometric composition.3 A crystal grown from a stoichiometric melt will solidify at a melting point maximum at which the solid will contain -0.5002 atom fraction of tellurium. PbTe single crystals grown in our laboratories from stoichiometric melts have carrier concentrations of 9 x 10" per cu cm, indicating that the excess tellurium in the crystals is as expected from this phase diagram. However, growth of PbTe from a lead-rich melt will result in material having a more nearly stoichiometric composition. Although the addition of Sn to the melt shifts the solidus curve further toward the tellurium-rich side,4 the general discussion given for PbTe applies to the Pbl-xSnxTe systems as well. EXPERIMENTAL Single crystals of Pb1-xSnxTe have been grown in our laboratories from nonstoichiometric, cation-rich melts using the Czochralski technique and boric oxide liquid encapsulation. The details of the growth apparatus and growth technique have been reported in a previous paper on growth of these alloys from stoichiometric melts.2 In the present study, three specific crystal compositions were investigated in detail; x = 0.00, 0.10, and 0.17. Growth of alloy crystals from nonstoichiometric melts requires considerable care, and good quality single crystals were obtained in this study only by optimizing the mechanical and thermal stability of the growth system and by using pull rates of from 1 to 3 mm per hr (Pbl-xSnxTe crystals are easily pulled from stoichiometric melts at rates of from 5 to 10 mm per hr). The liquid encapsulation technique was found to yield near-ideal conditions, since the B2O3 layer increased the thermal stability at the growth interface, permitted easy attainment of near-ideal thermal gradients, and dampened vibrations at the melt surface. The hygroscopic character of the B2O3 was a slight problem and vacuum heat treating was necessary to completely remove the water from the boric oxide. During initial growth, the seed diameter was reduced and a narrow neck (1 to 2 mm diam) of several millimeters length was grown. The latter steps were found to be necessary for the growth of single crystals, i.e., if either of these two requirements were

Jan 1, 1970

By Abdurrahman Cetinbas

The periphery of longwall panels in the Pocahontas No.3 coalbed is characterized by a zone of reduced permeability that inhibits the natural drainage of methane. A residual gas pressure of 105 psig was measured after 1 year in an isolated block of coal measuring 340 by 1,100 feet. The buildup of gas pressure within such large blocks causes methane problems during plowing operations. However, natural drainage holes drilled during development have been found to reduce the gas content of the coal in this coalbed by over 90 percent. The effect of water infusion on dust during plowing operations was investigated using existing methane drainage holes. These holes were cleaned of debris and a pipe was grouted into the hole for water infusion of the panel. Both total and respirable dust levels were reduced by 40 to 79 percent. Water infusion of the panel proved more effective than did the use of a plow-mounted spray system.

Jan 1, 1974