Search Documents

By Gruenewaldt von

Paper presented at the IAGOD international symposium on mineralization related to mafic and ultramafic rocks held in Orleans, France, 1-3 September 1993. The principles of shear-driven aggregation of particulate matter suspended in fluids, a common industrial method of concentration and separation, were applied to a convecting magma to estimate the time required to sparge or strip the PGE and Cr content and concentrate it into the boundary layers. It was calculated that an ore-grade (e.g. 6 ppm PGE) boundary layer about 1 m thick would require 100 000 years at most to form from a body of magma 500 m deep with a PGE content of 20 ppb. Since concentration would be most vigorous when the magma was warmest, at least half of this concentration would take place in the first 10 000 years. The effect of dispersive pressure in the boundary layer would generate a concentration high of refractories just below the top of each boundary layer and another just above the bottom. If the magma was a double-diffusive system, it might evolve by the downward cascade of enriched boundary-layer material into the hotter, lower magma layers, where depending on saturation levels chromites would equilibrate and sulphides undergo partial or total resorption, enriching PGE levels in any remaining sulphides. This cascade process would in time greatly enrich the lower regions in PGE-bearing sulphides and chromites

Apr 1, 1994

By R. T. Hukki

THE accepted basis of comparisons between mills of different diameter is the percentage critical speed. If n = actual mill speed, rpm, nc = calculated critical speed, rpm, np = calculated percentage critical speed, and D == inside diameter of the mill in feet, then n, In the following analysis capacity, T, is expressed in short tons per hour, tph, and power consumption, P, in kilowatts, kw. Accordingly power consumption per unit of capacity, P will be expressed in kilowatt hours per short ton, or kw-hr per ton. In all equations D refers to the inside diameter of the mill in feet and v to the peripheral speed of the mill in feet per minute inside the liners. ' Comparison between separate mills must be based on equivalent grinding conditions, i.e., same feed, same size distribution of feed, same size distribution of product, and same percentage of solids. In addition, comparisons between separate rod mills must be based on the same rods, same type of liners, and same percentage rod load. Comparisons between separate ball mills presuppose the same balls, similar liners, and same relative ball load. The practical np-range through which the equations apply varies, being narrower for fine grinding in ball mills and wider for coarse crushing in rod mills. The Relationship between Capacity and Speed It is the general belief that the capacity, T, of a tumbling mill is directly proportional to the speed of the mill, other things remaining constant.' Mathematically this is represented by the equation T - c¹ n tph [4] where c, is a factor related with the grinding characteristics of the ore, method of reduction, and the units chosen. It is proposed here that the general equation relating mill capacity and speed should be of the form T = c¹ nm tph [5] In other words, the capacity should be proportional to the mill speed raised to power m, the numerical value of the exponent being 1 5 m 5 1.5, depending on the circumstances. Eq. 5 can also be written in the following forms: T = c, (np)m tph, and [6] T=Ca vm tph, [71 where v = peripheral speed of the mill in feet per minute. If the observed capacity of a mill at speed n¹ is = T¹ tph, the capacity T² of the same mill at speed n² should be T² = T¹ (n²/n¹)tph [8] The Relationship between Power Consumption, Mill Diameter, and Speed The only well known theoretical deduction relating power consumption, P, and mill diameter appears to be the formula of duPont introduced by Gow, Guggenheim, Campbell, and Coghill.' According to duPont, the power required to operate a mill is a function of the mass of the balls, of the lever arm of the ball mass, and of the speed of the mill. The ball mass per unit of mill length is proportional to the square of the diameter, the lever arm is directly proportional to the diameter, and the critical mill speed or any percentage thereof is inversely proportional to the square root of the mill diameter. Following this reasoning, the original duPont formula is of the form P = c4D² c D • c6D-0.5 = c7D2.5 [9] If the mill speed in the above equation is expressed in terms of Eq. 3, the duPont formula may be written as follows: P=f1(D2) f2(D) f³(—np) or [10] vD P = c np D2.5 kw [11] Eq. 11 may also be derived from the mechanical principle of force, which is equal to mass x acceleration. Power necessary to operate a mill may be considered to be an homogeneous linear function of the force developed. Ball or rod mass per unit of mill length is a function of D2. The acceleration factor of the ball or rod mass is a function of the peripheral speed of the mill. Thus P = f4(F) = /x(D2) f5(v) Indicating that v = nDn, and n = c9 np /vD, the above equation becomes P = f2 (D2) -fa (D ca np/vD

Jan 1, 1955

Electrochemical measurements are presented on electro-deoxidation of silica in molten calcium chloride at 900°C, with porous silica pellets as starting material. Measurements during pre-electrolysis (to remove water from the melt) showed electrochemical noise, which is consistent with the evolution of hydrogen. Throughout, the dominant anodic reaction appears to be CO2formation, based on the observed potential at the anode, and measured anode wear. Because of the presence of dissolved CaO in the melt, some of the CO2 candissolve in the melt; the resulting calcium carbonate formation was confirmed by electrolyte analysis after reduction runs. Reduction of dissolved CO2 at the cathode is likely to contribute to the background current during the reduction process. For the electrode and cell configuration used here, most of the over potential arises from polarization of the anode, and ohmic potential drop in the electrolyte.

Jan 1, 2006

By M. Drozd, M. Somppi, Z. Yamak

"Granular activated carbon is widely used in the gold mining industry for gold extraction from aurocyanide-containing slurry. The extraction process can employ carbon as part of the gold recovery operation for various circuit designs including carbon-in-pulp (CIP), carbon-in-column (CIC), and carbon-in-leach (CIL) circuits. However, various qualities of activated carbon exist and the durability of the material can change significantly from source to source. Handling this expensive reagent can pose challenges when fine carbon losses occur in the CIP, CIC, and CIL circuits. Additionally, any gold that is adsorbed to these carbon fines can also be lost by various mechanisms including carbon attrition and fracturing, inefficient coarse-fine separation, and poor carbon fines capture. With the above in mind, a series of tests were conducted to investigate standardizing simple laboratory methods for testing carbon quality. A standard procedure beyond or enhancing ASTM methods can serve as additional starting points for evaluating carbon specific to the gold industry. The investigation focused on size distribution, flatness, wet attrition resistance, surface area, gold kinetics, and gold loading. The final results provided information to generate an equation for ranking carbon samples to plant performance.IntroductionActivated carbon for use in gold extraction is amongst the most commonly found processes in modern gold-milling plants. Although gold losses are inevitable in the milling process, operators often focus on the importance of maximizing gold recovery. One focus area that is important in gold recovery is optimizing the use of activated carbon and examining potential changes to realize improved economics for carbon-in-pulp (CIP), carbon-in-column (CIC), and carbon-in-leach (CIL) processes."

Jan 1, 2017

By T. L. Owen

Since 1993 Cyprus Amax has brought $2.5 billion dollars of greenfield and expansion projects into production, taking it from a mid-sized domestic minerals company into a major international minerals organization. The near simultaneous development of these multiple mineral projects in different locations around the world provided the opportunity for Cyprus Amax to develop a formal project management approach based, in large part, on an outsourcing philosophy. This formal project management system along with its outsourcing philosophy has served the growth agenda of Cyprus Amax extremely well. These preceding factors, coupled with the in-house retention of a core project group that fully understands the breadth of skills and abilities needed to undertake development of multiple large projects successfully, have been the cornerstone of Cyprus Amax’s project development success.

Jan 1, 2000

By E. Chin

The domination of Bangladesh's mineral industry by natural gas was in for some possibly significant changes. A modest flow of crude oil was struck in a gas development well in the northeastern corner of the country. This was the first commercial flow of crude oil in Bangladesh. All crude oil was being imported, which cost a significant proportion of the nation's foreign exchange earnings. The development of an oilfield producing only a few thousand barrels per day would be a welcome help to the economy. Additional exploration at a 1985 coal discovery in the northwest indicated a considerable reserve of good-quality coal at a depth suitable for mining. If the coal is mined, it would be a boon to the local economy because natural gas was not available in the area.

Jan 1, 1988

By Robert D. Saltsman

The inadequacy of our knowledge of the coal combustion process has long been recognized. This was expressed very well by Spicer and Finney (1). "The control of combustion processes in industry and the design of the equipment necessary for efficient burning to take place have always been very much branches of an industrial art rather than of an exact science. This has been especially true of the utilization of coal, a substance so hetrogeneous and complex in character that all too little is known about its chemical and physical composition.' During the past several years one branch of coal utilization, that of high temperature carbonization; has made significant advances from being an art into being an exact science. This has been accomplished by the development of petrographic techniques for identifying, measuring, and determining the thermal properties of the organic materials which affect the carbonization of coal and the correlation of this information with a pre-existing standard of coke quality, the stability index.

Jan 1, 1964

By Y. H. Wang

Micro-flotation tests of spodumene, beryl, quartz and feldspar have been carried out by using CaCl2 and FeCl3 as modifiers and a blending collector of oleic acid and hydroximic acid. CaCl2 shows efficient activation for spodumene when pH is above 11.5, and FeCl3 exhibits a markedly activation and good selectivity for spodumene in the range of pH 4 to 10. The main species of CaCl2 are CaOH+ and Ca(OH)2 when pH is above 11.5, and the main species of FeCl3?6H2O are Fe(OH)+2 and Fe(OH)3 during the pH range of 4 to 10. A selective flotation of spodumene and beryl from pegmatic ore had also been completed while using FeCl3?6H2O as activator and the blending collector. A bulk concentrate containing 1.087% BeO and 4.70% Li2O has also been obtained in the flotation of spodumene and beryl from pegmatic ore assaying 0.097% BeO and 0.45% Li2O, and the recoveries of BeO and Li2O in concentrate are 74.38% and 69.50% respectively.

Jan 1, 2014

By Rhulani F. Maluleke, Francis W. Petersen, John H. Marsh, Johann de T. Steyl, Allan Nesbitt

"Pressure leaching of chalcopyrite and nickeliferrous pyrrotite at temperatures between 105 and 200 ºC has been proposed as a potentially viable route for the extraction of mineral elements from sulphide concentrates. In general, these concentrates contain iron, and the economic success of the processes is partially dependent on the choice of the environmentally acceptable iron-removal technique. One of the most widely used methods for the removal of iron from sulphate liquors is precipitation as hematite, goethite, or jarosite. The nature of the iron precipitate formed dictates downstream dewatering and residue treatment and disposal options. However, a better understanding of iron precipitation under the defined process conditions would consequently be of benefit in process design and optimisation.This study investigated the precipitation of iron in the autoclave at temperatures between 105 and 200 ºC. The effects of temperature, acid concentration, iron concentration, and the presence of other metal cations on the nature and composition of the precipitates were determined."

Jan 1, 2003

By C Li, D O’Dea, R Moreno-Atanasio, T Honeyands

The behaviour of iron ore granules in the feeding process of sintering is significantly influenced by the material properties of the granulated mix. Therefore, the measurement of key material properties of the iron ore granulated mix is indispensable prior to the simulation of the sintering process based on the discrete element method (DEM). In this paper, three key property parameters of the iron ore granulated mix, apparent density, elastic modulus and rolling friction coefficient, were measured in laboratory-scale experiments. For different sintering processes, the moisture content of the granulated mix normally varies according to the specific requirements for granule size distribution and operating conditions. Therefore, understanding the effect of moisture content on the property parameters of iron ore granules is very helpful in accurately determining the property parameters for DEM simulation work. In this paper, six groups of iron ore granule samples with six levels of moisture contents were prepared through granulation and the trends in apparent density, elastic modulus and rolling friction coefficient with the increase of moisture content were plotted and analysed based on the measurement results. The results show that as moisture increases from 6.9 per cent to 9.1 per cent, the apparent density decreases from about 3000 to 2800 kg/m3. With moisture increasing within the same range, the elastic modulus first decreases from over 200 MPa to below 100 MPa and then reaches a relative constant value of about 40 MPa at higher moisture contents. Rolling friction coefficients are measured using two methods with both indicating a similar trend, with the rolling friction coefficient first decreasing and then rising as moisture increases from 6.9 per cent to 9.1 per cent. The relationship between µr and µ’r is assumed to be similar to that between static and dynamic friction coefficients.CITATION:Li, C, Moreno-Atanasio, R, O’Dea, D and Honeyands, T, 2017. Variation in property parameters of iron ore granulated mix with moisture content, in Proceedings Iron Ore 2017, pp 79–84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Dale S. Preece, J Paul Tidman, Stephen H. Chung

A discrete element computer program named DMC-BLAST (Distinct Motion code) has been under development since. 1987 for modeling rock blasting (Preece & Taylor, 1989). This program employs explicit time integration and uses spherical or cylindrical elements that are represented as circles in two dimensions (2-D). DMC-BLAST calculations compare favorably with data from actual bench blasts (Preece et al, 1993).

Jan 1, 1998

By G. S. Scott

[In the course of the investigation the Bureau of Mines is carrying on to determine the causes, behavior, and control of mine fires, the detection of incipient heating underground in the mines and above ground in refuse banks has received consideration. A report has been puplished5/ describing apparatus and tests made on anthracite to determining the amount and composition of the oxidation products when normal dry air was passed through it at temperatures varying from 100° to 350° C. These tests showed that the amount of evolved gases and their relative prorortions varied with the temperature. From: these results, graphs were prepared by which `he temperature at which the coal was oxidized could 'be estimated, thus giving a possible means of detecting incipient heating.]

Jan 1, 1938

By Caroline Olsen

The objective of this study was to achieve Zn activation control in an industrial Cu flotation circuit treating a complex Cu-Pb-Zn-Au-Ag sulphide ore at the LaRonde Division of Agnico-Eagle Mines Limited (Québec, Canada). In order to provide process relevant results, a laboratory testing methodology was developed to duplicate plant operational parameters. The action mechanisms of ZnSO4, TETA (triethylenetetramine) and NaHSO3used as depressants in order to limit ZnS activation were examined. Laboratory flotation tests with and without Cu2+ions (the ions responsible for ZnSactivation)were performed. All depressants showed equal or better flotation performance relative to baseline tests. For example, in the presence of Cu2+, the Zn recovery reduced from 32.2% to 17.5% in the copper rougher concentrate after adding ZnSO4(with a dosage of 50 g/t). TOF-SIMS analyses confirmed the relative decrease in surface Cu in the samples treated with ZnSO4and TETA. For the case with TETA, this indirectlyindicates the formation of a copper TETA complex in solution, thereby reducing available Cu for transfer. The TOF-SIMS and XPS data indicate that the addition of ZnSO4and NaHSO3resulted in an increase in surface metal hydroxides and SO3 on ZnS grains inhibiting both Cu and collector attachment.ZnSO4 was subsequently tested with success in the LaRonde concentrator. The addition of 40 g/t ZnSO4 at the conditioning (or cleaning) stage led to a 2% reduction in Zn content in the Cu and PM concentrate. Recently, improvements towards the control of copper sulfate addition in the downstream Zn flotation circuit resulted in the reduction of Cu2+ in process water. As this ?cleaner? water is recycled for Cu and PM flotation, the addition of ZnSO4 is now used only as required.

Sep 1, 2012

By G. S. Scott

[In the course of the investigation the Bureau of Mines is carrying on to determine the causes, behavior, and control of mine fires, the detection of incipient heating underground in the mines and above ground in refuse banks has received consideration. A report has been published5/ describing apparatus and tests made on anthracite to determine the amount and composition of the a oxidation products when normal dry air was passed through it at temperatures varrying from 100° to 350° C. These tests showed that the amount of evolved gases and their relative proportions varied with the temperature. From these results, graphs were prepared by which the temperature at which the coal was oxidized could be estimated thus giving a possible means of detecting incipient heating.]

Jan 1, 1938

By Derrick D. Dasenbrock

Three piers of a new river bridge are supported on 1.067 m diameter open-end steel pipe piles. At time of drive, and after pile re-strikes, high-strain dynamic capacity values at plan tip elevations, were as low as 23% of design requirements. Pile lengths were extended 20% to 40% deeper than planned at two piers, driving to rock, impacting both the project cost and schedule. The significant discrepancy between predicted and observed capacity was investigated through a series of coordinated dynamic tests; a full-scale test pile was installed and monitored over 221 days by both dynamic and quasi-static methods. Unusually slow strength gains were observed by dynamic monitoring on all piles installed at the site. CPT soundings were advanced at the test pile and through the pile interior to investigate the soil plug. High-strain dynamic methods were found to have significant limitations in properly assessing the long-term capacity of large-diameter open-end pipe piles during driving and short-term pile re-strikes. As the benefits of large diameter high-capacity open-end pipe piles are numerous, the geotechnical community needs to address appropriate construction monitoring and control of these foundation types to take full advantage of these systems. An improved understanding of the physical effects of pile installation and the impact on soil strength assessment while driving and long term soil strength gain should be developed and incorporated into both design and monitoring procedures to avoid either unsafe or needlessly costly designs.

Jan 1, 2006

By M. Okido, W. Wei, L. Chai

The kinetics on the growth of Thiobacillus ferrooxidans was studied by use of series piezoelectric quartz crystal ( SPQC ). Arsenic ioninhibits the growth of Thiobacillus ferrooxidans, which is consistent with the previous results by other measuring method. This further demonstrates that the SPQC can monitor the chemical activity of the growth of Thiobacillus ferrooxidans. Cupric ion accelerates the growth of Thiobacillus ferrooxidans. The mechanism was discussed, it was considered that copper promotes the protein enzyme of Thiobacillus ferrooxidans, rustic yanin, to form over the range of cupric ion concentration studied. There action order of cupric ion in accelerating the bacterial growth is 0.067. The growth of Thiobacillus ferrooxidans is dependent on temperature, the apparent reaction activation energy decreases from25.56 kJ / mol to 18.32 kJ / mol because of the addition of 10 mg / L Cu(II) to the bacterial growth solution of pH 2.0 at initial inoculum of 10%.

Jan 1, 2000

By Robert Blickensderfer

Tungsten alloys with high-temperature strength properties, comparable to the best of alloys recently developed by others, were produced by a new process called here the oxyreaction process. The process involved additions of a powder of a reactive metal compound, ZrN, ZrW2, or HfW2, to a base metal powder, tungsten, which contained some oxygen. The powders were blended, compacted, sintered, and extruded. During sintering, diffusion and internal oxidation occurred to produce reactive-metal oxide particles and solid solutions. A dispersion of oxide particles could be precipitated by heat treating. The oxyreaction process circumvents many of the agglomerating and coarsening problems encountered in the current methods for dispersing a stable oxide in a metal. Oxyreaction strengthening results from solid-solution strengthening and from dispersion strengthening produced by the reactive metal and its oxides. At a test temperature of 1,650° C, the alloys prepared from WW, had tensile strengths up to 70,000 psi and stress-rupture lives up to 142 hr at 10,000 psi stress; the alloys prepared from ZrN powders had tensile strengths up to 80,000 psi and stress-rupture lives up to 27 hr at 10,000 psi stress. Tensile strengthening in the alloys was attributed to Zr in solid solution or to Zr-O-W structures too small to be observed in an electron microscope replica. Stress-rupture life was attributed to a dispersion of submicron Zr02 particles which precipitated and grew to 0.05-to 0.2-micron size during the test. Tensile strengthening and stress-rupture life were dependent upon both the zirconium and oxygen contents with the maximum occurring at roughly 0.9 atomic pot Zr and 0.9 atomic pot 0. Studies of the details of the oxyreaction process were made on the W-ZrW2 alloys and three general steps were determined: (1) The reaction of 0 in tungsten powder with ZrW2 to form relatively large Zr02 particles; (2) the dissolution of remaining ZrW2 into the W matrix and partial internal oxidation to form ultrafine but sparse zirconium oxide particles and possibly to establish Zr-O-W structures; (3) the development of ultrafine Zr02 particles during high-temperature aging.

Jan 1, 1971

1994 estimates for Porgera are probable and proven reserves of 58 200 000 t of ore grading 5 g/t Au. Gold mineralisation is related to an intrusive complex emplaced at shallow levels in poorly consolidated sedimentary rocks. The complex is located in a zone of fold-and-thrust deformation, whose formation may have been initiated shortly before emplacement and continues locally today. Abundant primary magnetite in the complex gives an intense, 5 km wide aeromagnetic anomaly. The deposit formed during two main stages of mineralisation, the first related to early magmatic-hydrothermal activity and the second representing later epithermal overprinting centred on the Roamane fault. Hydrothermal alteration followed closely on emplacement indicating a close genetic relationship between magmatism and mineralisation. Both stages of hydrothermal activity post-date and overprint early propylitic alteration. Several factors have acted in unison or sequentially to concentrate metals at the deposit, including an extensional or trans-tensional tectonic setting within an arc or collisional environment, the exsolution of a magmatic hydrothermal fluid prior to sulphur saturation in the melt, the development of the hydrothermal system into one favourable for transporting gold, the action of late-stage faulting in focusing epithermal fluid flow, and the role of dissolved gases in promoting fluid phase separation and high-grade ore deposition

Jun 19, 1905

By Shivendra Sinha

Total pressure oxidation (TPOX) is widely outreached leaching practice for base metals from sulfide minerals, wherein high temperature (T ∼ 200 °C) and oxygen pressure (pO2 ∼ 25 bar) are required. These aggressive conditions intensify the oxygen mass transfer, and therefore facilitate metal dissolution. However, challenging-cum-negative aspects of such practice are energy and material intensive requirements and high oxygen demand. Thus, the present study explores the novel emulsified medium for enhancement of oxygen mass transfer, which assists faster metal dissolution at significantly lower temperature and pressure condition. It is possible to achieve quantitative dissolution (>95%) of Cu, Ni and Co from mixed sulfide minerals at T ∼ 95 °C and pO2 ∼ 2 bar using an emulsion of 2.5% (v/v) n-Hexadecane in dilute sulfuric acid. In addition, n-Hexadecane was found to be inert, stable and immiscible in a pressurized leaching system, thus can be easily separated and recycled in subsequent leaching stages. Thus, this study offers an energy efficient route for low temperature-pressure leaching of sulfides.

By R. A. Jankowski

The U.S. Bureau of Mines (USBM) conducted a series of laboratory tests to investigate the effectiveness of using a flooded-bed scrubber with exhaust ventilation in deep-cut faces of up to 12.2 m in length. An experimental test program to determine the impact on respirable dust levels resulting from changes in face airflow, curtain setback distance, operator positioning, and operating parameters of the external spray system on the miner was completed. Gravimetric sampling was conducted in the immediate return and at three sampling locations on the off-curtain side of the entry. Statistically significant differences in dust levels on the order of 0.5 to 1.2 mg/m3 were observed between specific sampling locations and changes in several test parameters. Dust sampling results indicated that a flooded-bed scrubber and exhaust ventilation can be a viable dust control system for extracting deep cuts up to 12.2 m in length. The impact on methane was not evaluated.

Feb 24, 1997