Search Documents

Common brattice cloths in use in Australian coal mines are compared by permeability measurements. The respective advantages of twill weave and tarpauling* weave cloths are listed, and the improvements to be obtained in the ventilation of a mine by using tarpauling cloths instead of the commonly used twill cloths are stressed. Plastic cloths are widely used overseas and are briefly discussed.INTRODUCTIONThe onset of extensive full-scale mechanization in Australian coal mines during the past few years has increased attention given to the ventilation of working places. Many inadequacies of the present system have been brought to light and not the least of these is connected with the use of brattice cloth, both in directing the flow of air around the face and in acting as a temporary sealing mechanism. A well-constructed line of brattice will only provide fair ventilation for a distance of 100 ft. Beyond this point the volume or air reaching the face falls off rapidly.Some of the shortcomings associated' with the use of brattice cloths are:1. Hurried installation, necessitated by a rapid advance, often results in poor workmanship with, consequently, an excessively high leakage rate.2. High places caused by falls of roof are difficult and time-consuming to seal.3. Curtains, in lines of brattice crossing transport routes, are difficult to maintain.4. Lines of brattice interfere with rock-dusting and clean-up of fine coal.5. Repair and maintenance of brattice consumes much...

Jan 1, 1959

By M. P. Ristenbatt

A new automated post-disaster signaling system, intended to use through-the-earth EM propagation, was demonstrated in the laboratory at an input SNR of -34 dB. The system presently available requires an input SNR of +6 dB, and uses a human-ear detector. The work here demonstrated coherent integration, for the automated system, in multiples of 17 s, up to 1088 s (18 minutes). A repeating pseudorandom (or pseudonoise) signal is used, which offers an ideal auto-correlation at the receiver matched-filter output. A novel decision-variable algorithm achieves the estimate of noise level by using those matched-filter output samples that occur between the signal auto-correlation peaks. This work included corraboration that the received signal power decreases as distance to the tenth power, for through-the-earth propagation. Thus, the above 40 dB reduction in required input SNR permits an automated system to have a range 2.5 times that of the present system. In addition, an automated system permits the possibility of operating receivers around-the-clock; this would reduce the initial-detection-time from a few hours (present system deployment time) to a few minutes (signal processing time).

Jan 1, 1981

By A. El-Midany

Dolomite impurities are increasing in the currently mined phosphate deposits in Florida. Several research efforts have been conducted in various laboratories around the globe to find methods to economically removing the dolomite. However, a universal and cost-effective process is not now in commercial use. In this paper, a new process for dolomite/apatite separation is presented. The differential solubility of dolomite in slightly acidic solution is utilized to generate micro CO2 bubbles at the dolomite/water interface. Particle (dolomite)/bubble aggregates float to the surface leaving phosphate concentrate with low MgO content. Interestingly, up to 6.0 mm particles can be floated by such micro-bubble/particle aggregates. Different surface-active agents were tested to stabilize the bubbles. Results of these tests are presented, and the mechanisms involved are discussed.

Jan 1, 2009

By Kathleen M. Kowalski

This research explores the emergence of leadership in a crisis situation. The study by the U.S. Bureau of Mines focuses on three underground mine fires and the resulting evacuations. The subjects for this study are 48 coal miners, who evacuated the mines as part of eight escape groups, The subjects described their escape during an open-ended interview. Data were coded according to: (a) evidence of leadership behavior, (b) evidence of lack of leadership behavior, and (c) characteristics of the individual in each group who led the subjects out of the mine. During analyses, attributes of the leaders, who facilitated the escapes, were noted and compared as were instances of lack of leadership. The structure of the group leadership before the crisis was compared with the reality of the leadership during the crisis. Some groups experienced an apparent breakdown of leadership during their escape, while others witnessed the emergence of leadership. Consensus characteristics of the leaders, who emerged during these crises, are discussed and generalizations drawn. Research into leadership during emergency escapes is needed to provide information for training in prevention, escape, and rescue. The authors suggest questions for further investigation and topics for further inquiry into the area of leadership evolvement during crisis.

Jan 1, 1994

This report presents the results of studies of Kennecott Copper Corporation's tailings embankment at Magna, Utah. The stability studies described were performed on only one cross section of the embankment, utilizing; data obtained from drilling, sampling, and testing, which was limited in nature. The main objective of the data collection was to provide background information to support the overall research effort. Because of this limited scope, it is not possible to evaluate the degree of safety or adequacy of the embankment or disposal system, and the information and data contained in the body of this report must be judged in that light. The first part of this report contains discussion of site geology and seismicity, pertinent information on the refuge disposal system, a discussion of the tailings materials characteristics, a summary of the engineering analyses, and A bibliography. The second tart (appendices) contains basic geologic and engineering data supporting the discussions in the first part of the report.

Jan 1, 1974

By T. C. Souza Pinto

Because shape is an assessment of the three-dimensional form of a particle, it may be described in terms of sphericity (?), which is a measure of how closely a particle approaches a spherical configuration. In this study, Darcy?s law and the Kozeny-Carman model for fluid flow through porous media were applied to packed beds to determine the sphericity (?) of apatite particles. The beds were composed of glass spheres or particles of apatite (igneous from Brazil and sedimentary from the United States) of three classes of size (Class 1: -297 +210 µm; Class 2: -210 +149 µm; Class 3: -149 +105 µm). Glass spheres were used to validate the model because of its known sphericity (? = 1.00). Apatite particles, either igneous or sedimentary, showed very close values for particle sphericity (? ? 0.6). Observations on particle images conducted by scanning electron microscopy illustrated that igneous (? = 0.623) and sedimentary (? = 0.644) particles of apatite of Class 2 predominantly exhibit elongated shape. The close value of particle sphericity (? ? 0.6) showed by either igneous or sedimentary apatite may be justified by the similarity in particle shape.

Jan 1, 2009

By Thomas M. Barczak

The 1990s brought an unprecedented increase in the development of innovative technologies to provide more effective and easier-to-install roof support in underground mines. To facilitate the application of these technologies in improving mine safety, the National Institute for Occupational Safety and Health (NIOSH) developed the Support Technology Optimization Program (STOP). STOP is a Windows-based software program that provides mine operators with a simple and practical tool to make engineering decisions about the selection and placement of these various roof support technologies. The program includes a complete database of the support characteristics and loading profiles obtained through safety performance testing of these supports at the NIOSH Safety Structures Testing Laboratory. A support design criterion in the form of the required support load density at a specified convergence can be established from four options: (1) a database of measured ground reaction obtained from various mines or ground behavior information input by the user,(2) load requirements based on a detached roof block or rock failure height, (3) criteria based on the current roof support system, and/or (4) arbitrary criteria set by the user. Using these design criteria, the program will determine the installation requirements for a particular support technology that will provide the necessary support load density and convergence control. Optimization routines are also available to determine the most efficient support design for a user-specified support installation. In addition to these performance measures, STOP can be used to compare material handling requirements and installation costs. Comparisons among the various support technologies are easily made, including a graphical analysis of relevant support parameters. This paper describes STOP and its application to optimizing standing secondary roof support systems.

Jan 10, 2000

By Abraham Lindo

"Blasting plays a key role in hard rock underground mining. It is by nature a violent and destructiveextraction method designed to economically fragment the rock into a suitable size for it to be loaded and hauled as part of the specific mining process while controlling the amount of damage to the surrounding rock mass."

Jan 1, 2016

The 105th Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the J.C. Lemmer Auditorium, SA National Museum of Military History, 22Erlswold Way, Saxonwold, Johannesburg on Thursday, 8thAugust, 2002. Welcome The President extended a special welcome to the guests and representatives of our sister institutes and other associations. Also to recipients of awards, senior members of industry, Honorary Life Fellows, Past-presidents, our Members and other guests, among them the following: Mzolisi Diliza, Chief Executive, Chamber of Mines of South Africa Dawie van Wyk and Rod Tucker, Vice-presidents, The Geological Society of South Africa Vaughan Townsend, President, Institute of Certificated Mechanical and Electrical Engineers, South Africa Karel Landman, President, Institute of Mine Surveyors of South Africa Frik Grobbelaar, South African Colliery Managers? Association Pierre Ballot, President, South African Institute of Electrical Engineers Trueman Goba, President, South African Institution of Civil Engineers

Jan 1, 2002

By S McKinley, S Juras, E Uludag

More and more, today’s mining geologists are asked to identify and create 3D value domains for multidisciplinary usage: grade definition, geometallurgical performance and geotechnical characteristics, to name a few. Often, that domain shape is the result of an assumed or conjectured value as a surrogate to a set of conditions (eg kaolinite-rich, sericite alteration). Would it not be instead better to create the respective domain through identification of a consistent quantifiable geologically-based pattern as its basis?Critical to the identification of patterns is the transformation of 3D point data into a model by a method that uses few, if any, preselected thresholds. Too often we complicate the reviews of the modelled data by prejudging the value range of interest. And when we do revert to 2D views (ie sections and plans), we tend to only examine numbers or line traces. These hinder and obscure identification of geological patterns particularly in deposits of complex geology. Instead, these data should be looked at with minimal prejudgment and interrogated in 2D space by one of the best and most eye-catching display types: filled contour plots.Here we present two different processes that transform data with minimal preselection into formats that allow for pattern recognition by filled contour plots. These are: probability assisted constrained kriging (PACK) and multiple interval interpolant formation (Aranz Geo’s Leapfrog® software). The former creates a 3D model of probabilities on a threshold value; the latter creates numerous (=10), regularly-binned 3D interval interpolants. The results of each method are examined as filled contours over numerous sections or plans. Any distinct patterns are quickly discerned thereby readily identifying the best value to base the creation of a domain. These processes therefore provide a way to marry recent advances in software tools with what is supposed a geologist’s core skill: pattern recognition.CITATION:Juras, S, McKinley, S and Uludag, E, 2017. Pattern recognition in transformed data – the search for domain shapes in mine geology data, in Proceedings Tenth International Mining Geology Conference 2017, pp 37–42 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

Three complete connector assemblies and six separate contacts were submitted to a series of tests to establish the connectors permissibility and compliance with U. S. Bureau of Mines research Contract #H 0110423 D.C. portion. Test Procedure TPC-0118 was coordinated, and the test plan approved by the Bureau as fully complying with the intent of the contract for the direct current connectors. The components and connector assemblies have been demonstrated in testing that they meet or exceed all the requirements of the test procedure.

Jan 1, 1974

THIS paper proposes to give a general description of the pumping and other machinery in use at the Thames Hauraki Pumping Station, situated on the Thames goldfields of the North Island, New Zealand. An idea of the general arrangement of the pumping engines and pumps can be obtained, together with a certain amount of detail, by reference to the illustrations. The history of the pump is rather interesting, and is as follows: -In 1894 the Government decided that a subsidy of £1 for £1up to an amoUllt not exceeding £25,000 be granted towards the erection of suitable machinery to exploit the Thames low levels.With a guarantee of such assistance a company was floated in London, with a capital of £300,000, to develop several properties at Thames. As the old Queen of Beauty Company had produced bullion worth £400,000 prior to closing down on account ofa breakdown to its pumping gear, their shaft was chosen as the site of the principal work. As soon as the company was floated, operations were commenced at the Queen of Beauty shaft, situated at the entrance of the Waio-Karaka Creek, and not more than about half a mile distant from the principal mines on the field.

Jan 1, 1912

By Jimmy Thompson

The Santa Clara Valley Transportation Authority is designing the Silicon Valley Rapid Transit Project in San Jose, California. The project includes 6.9 km (4.3 miles) of twin-bored tunnels to be constructed through downtown San Jose using two earth pressure balance machines (EPBMs). This paper begins with a project description and update of the project status followed by a description of the relationship between anticipated ground conditions and EPBM requirements. Topics addressed include soil conditioning, abrasion resistance, annulus grouting, face pressure estimation, additional pressure control devices and control measures to limit over-excavation and settlement.

Jan 1, 2008

By Mehrotra G. M, Frohberg M. G

Based on the concepts of statistical thermodynamics of athermal mixtures, an approach is developed which is capable of quantitatively explaining the thermodynamic properties of binary silicate systems. Expressions for the ionic fractions of various anionic linear and nonlinear chain polymers are derived. The developed expressions for free energy of mixing are tested by applying these to the system PbO-SiO2. The ionic fractions of various chain polymers in this system are calculated. The two cases, namely, of linear and nonlinear chain polymers are compared with each other.Limitations of earlier models are pointed out.

Jan 1, 1975

By Roy C. Bartholomae

This Bureau of Mines report presents the results of a laboratory investigation of coal cutting mechanics and noise. These experiments were performed using linear cutting apparatus that operates over a broad cutting speed range. The influence of several coal cutting parameters on the noise, force, productivity, and specific energy associated with linear cuts was ascertained. Some basic theoretical aspects of coal cutting mechanics and noise generation are discussed, and the results of the laboratory experiments are used to formulate analytical models of the coal cutting forces and noise. The analytical model for coal cutting noise is then generalized to account for the more important effects of rotary cutting. Based on the generalized model, an estimate of the sound pressure level at an operator's position is made for a typical continuous mining machine. It is concluded that by employing linear rather than rotary cuts, using deeper depths of cut, slower cutting speeds, and more efficient cutting tools, it is possible to reduce the level of coal cutting noise, as well as provide benefits to other important areas of health and safety in underground mining.

Jan 1, 1983

By J. F. McDermott

The problem of converting our raw coal, and especially those coals that are not suited for long storage, in other words soft, into a fuel which would be at once clean; of a high B. t, u. content and low ash, is one that has occupied the minds of many able chemical engineers and hydrocarbon technologists during the past few years. Low temperature carbonization is the present outcome of this line of research, and many methods have been evolved of recent years to turn out a serviceable, useful fuel, and at the same time, save the by-products. As most of the research and data within my experience and knowledge pertains to lignite or sub-bituminous coals, I will confine my remarks to coals of that character and grade: I might say that Colorado coals, commonly called lignite, are not in reality true lignite, but are sub-bituminous, although I have in my possession an analysis of a Colorado coal which shows a moisture of 17 per cent, volatile 31.5 per cent, fixed carbon 28.8 per cent, and an ash of 22.7 per cent, and B. t. u. less than 8,000. Even this, though useless for domestic or indeed industrial purposes, could not be classified as true lignite. However, for the purposes of this paper I will refer to these coals as lignite. Two thousand pounds, or one ton, of raw lignite carries about 20 per cent moisture. This, of course, varies in some coals, but is, I believe, a fair average. For carbonization purposes this is usually dried to a 5 per cent moisture, therefore leaving but 1,700 pounds of coal to be placed in the retort. From present knowledge, and with the average process of carbonization, 70 per cent of this coal will come out carbonized, or 1,190 pounds, to which is added about 10 per cent pitch, which is fried out as the coal passes through the retort, and which is used as a binder, making a total of 1,360 pounds of coke or carbonized coal. This is usually in appearance a dark colored, rather porous coke of about the size of pea coal. It burns without smoke and have a very high B. t. u. content. According to most authorities on this subject, carbon, hydrogen, oxygen, nitrogen, sulphur and ash constitute the only elements on which carbonization value of a coal depends, and of these hydrogen is the most important. It is claimed the value of a coal for carbonization purposes may be roughly surmised from the hydrogen content. If this is promising, that is, showing an available hydrogen content of from 3 to 5 per cent, the coal should be given a careful ultimate analysis. Should the seam, as often happens in lignite coals, show varying bands of coal of different structure or appearance, samples should be taken from each band as well as a gross sample taken down the face of the seam in the usual way. This is in order to determine what part of the seam is most promising for by-product processes. A seam showing a high nitrogen content adds to the attractiveness of the coal in carbonizing as; if available nitrogen is 2 per cent or better, it should give a very high ammonia yield.

Jan 1, 1923

By Gabka T., R. E. Gregorczyk

Work to improve employees' behavior in Głogów Copper Smelter began in 2009. It has been noted that over 90% of accidents at work are attributable to human reasons. At that time, a series of external workshops was contracted based on exercises conducted by a psychologist trainer with supervisors. Having trained about 300 employees, an observation of employee behavior at workstations was started as part of the control of risk reduction measures. As a result of the above actions, the number of accidents was reduced by half between 2009 and 2017. Currently, internal workshops for communication improvement for behavioral auditors are conducted by the employees of the Smelter. Named: "I observe, react and communicate" and aimed at further mastering the elements of the safety culture in Głogów Copper Smelter. INTRODUCTION KGHM Polska Miedz is an integrated mining and smelting copper producer based in Poland and operates on the international metal market. KGHM, with annual production of over 500 thousand tonnes of copper, holds a middle position in the world ranking of copper producers. At the same time, in Europe it is the largest producer of copper from its own ore deposits, possessing its own integrated production structure, from underground mining operations to final, top-quality product. It is also worth mentioning that KGHM Polska Miedź is one of the largest Polish exporters and, apart from copper, is a significant primary silver producer in the world. The mission of our company, consistent with its strategy, is to produce copper and silver in a safe mode for workers and the environment, with reduced environmental impact. Therefore, "Głogów" Copper Smelter operations are continuously focused on the creation of safe working conditions, and minimizing the negative effects on the environment. The company meets the requirements of an Integrated Management System comprised of the following: Quality Management System ISO 9001:2008 Environment Management System ISO 14001:2004 OHS Management System according to the requirements of BS OHSAS 18001:2007 Being a proud socially responsible company, we are aware that part of an efficient OHS system is to recognize, monitor, prevent, educate and motivate, thus continuously improve working conditions for 2500 employees of Głogów Copper Smelter &Refinery. We clearly communicate that a low accident rate is beneficial for both, staff and the company, and is of utmost importance as a part of our health policy.

Jan 1, 2019

YOUR mom was right …count to 10. Most workers today report that they find their jobs stressful. Miners, in particular, are faced with hazardous and changing environments. Every shift provides different conditions and challenges. Coping with stress is an important tool to maintain your physical and mental health. Now, back to mom. Studies on stress tell us that shifting your focus away from what is causing your stress increases your ability to cope. Counting to 10 is one method. Science proves mom right. The stress response We are born with the stress response, which is a survival instinct, sometimes called the "fight or flight" response. When approached by a tiger in the jungle, our ancestors would perceive danger and prepare to fight or run. The body prepares for the fight or flight response in a number of ways. The bloodstream brings extra glucose and oxygen (fuel) to the heart, the sense of pain is dulled, and memory and thinking improve. The pupils dilate for better vision and the lungs take in more oxygen, while heart rate and blood pressure increase. Body hairs become erect, as puffed-out hair makes an animal look bigger and more dangerous. Once the perceived danger is gone - we have run fast enough to get away from the tiger or won the fight - the body returns to normal functions. Unfortunately, civilization gives us too many opportunities to experience this response. If activated too often, it can create wear and tear on the body, which may lead to injury and illness. Chronic and traumatic stress There are two key types of stress: chronic stress and traumatic stress. Both types can cause both physical and psychological symptoms. Chronic stress builds up from the day-to-day hassles. Traumatic stress results from a traumatic event such as a natural disaster, a mine disaster, or the sudden death of a loved one. Chronic stress is associated with an increased risk of a number of health problems including heart disease, depression, back pain, and carpal tunnel syndrome. Traumatic stress may lead to post- traumatic stress disorder (PTSD), Miners may experience both chronic and traumatic stress in their work.

By David Seaman, J-P Franzidis, Emmy Manlapig

"A new device has been developed to directly measure the bubble loading of particle-bubble aggregates in industrial flotation machines, both mechanical flotation cells as well as flotation column cells. The bubble loading of aggregates allows for in-depth analysis of the operating performance of a flotation machine in terms of both pulp/collection zone and froth zone performance. This paper presents the methodology along with an example showing the excellent reproducibility of the device and an analysis of different operating conditions of the device itself.The device has been used to investigate the froth selectivity of attached particles. Simultaneous measurements were made using a different froth recovery measurement technique in the same flotation cell. A comparison of these techniques shows that in this case, particles are selectively detached from bubbles at or near the pulp-froth interface.INTRODUCTIONA flotation cell can be considered to operate in two distinct phases or zones; namely the pulp or collection phase and the froth phase. The pulp zone is responsible for the formation of hydrophobic particle-bubble aggregates, whilst the froth phase is responsible for the separation of these aggregates from surrounding suspended hydrophobic and hydrophilic particles. Thus, the froth phase is the grade determining phase in flotation. A measurement of the bubble load (the mass of particles attached to air bubbles in units of mass/volume) will enable the analysis of the performance of both the collection zone at creating bubble-particle aggregates and also the froth zone at separating these aggregates from surrounding pulp.A measure of froth zone performance that has been used extensively in flotation research is the Froth Recovery, Rf, of a particular system. Froth recovery is defined as the mass of particles collected in the concentrate launder by true flotation as a fraction of the mass of particles entering the froth phase. The measurement of bubble load allows for this term to be calculated easily, rather than having to go through the laborious task of, for example, changing froth depths to determine this performance criterion (Contini et al., 1988; Vera et al., 1999b; Feteris et al., 1987)."

Jan 1, 2004

By Erwin Riyanto, Roy William, Karl Llewellyn

The Deep Mill Level Zone (DMLZ) mine is currently one of the deepest block cave mines in the world. The rock mass is heavily veined with little to no joints and faults are usually healed cohesive structures leading to difficult cave mining conditions. The caving process is improved if the rock mass contains fractures with sufficient density that it will cave by gravity as undercutting progresses. Hydraulic fracturing (HF) has been used to create fractures around the cave to improve mining. A seismic monitoring system has been used in DMLZ since the start of mining. Therefore, the seismic activities before, during and after HF can be monitored. Shear wave splitting is a process used to study the impacts of HF on the rock mass. This process involves the measurement of travel times from splitting shear waves after seismic events and using this to define the anisotropy within the rock mass and subsequently fracture density. This paper sets out the methodology for carrying out the interpretation of the shear wave splitting process using seismic data from the fracked cave crown and abutments along with an overview of the benefits to cave mining as result.

Apr 26, 2022