Search Documents

By Antti J. Perala, Teemu J. Yli-Kovero

"Efficient use of land is constantly requiring more underground construction. Minimized execution time and disturbance to surroundings and nearby structures are essential benefits for all construction techniques. To meet the demands of a modern construction project, suppliers have to be able to provide high-quality and tailor-made products just on time. RD pile wall is a retaining wall based on drilled steel pipe piles which are connected to each other with special interlocking profiles. RD pile wall is a solution which enables penetration of overburden soil, dense fill layers including stones and boulders, and embedding into the bedrock in one single operation. Several test installations and laboratory tests have been made to develop the system and to test and improve the water tightness of the wall. Beside these tests, RD pile wall has also proven its reliability in almost 70 projects. Largest project so far has been Pasila Tripla project in Helsinki, Finland. A permanent retaining wall with surface area of 18,000 m2 (193,750 ft2), excavation depth of 21 m (68 ft) and over 17 m (56 ft) of water pressure was made with 711 mm (28”) and 406.4 mm (16”) pile sizes. Piles were delivered to site in one piece with lengths up to 33.5 m (110 ft).INTRODUCTIONExcavations in cramped city centers and in between of existing buildings and other structures are facing more and more challenges. Installation of sheet pile walls is often problematic or even impossible due to obstacles in ground from old structures and due to demand to extend the excavations to even deeper and harder soil layers. Also installations of secant pile walls are facing difficulties due to cramped construction sites and constantly tightening execution times.On the other hand, an efficient and reliable piling technique suitable for the demanding soil conditions described above, percussion drilling, has been developed since the 1960’s, and especially from the mid- 1990’s, when the concentric drilling method with the ring bit and pilot was introduced. A new retaining wall application, the RD pile wall, was developed by combining that drilling method with the widely used retaining wall solution based on steel pipe piles and welded interlocks (a pipe pile wall normally installed with vibratory or impact hammers).PRINCIPLE AND MAIN BENEFITS OF THE METHODRD pile walls can be used in all soil conditions. Most beneficial the system is in extremely demanding soil conditions where the installation of traditional retaining walls is challenging or even impossible. The RD pile wall is a combination of drilled steel pipe piles and interlocking sections as shown in Fig. 1.Individual RD piles are connected to each other with interlocks welded to the piles on the automated welding line at the workshop. The matching dimensions of the drilling system and interlocking sections allow the installation of RD piles through stones and boulders and even into the bedrock, if necessary, in a single operation. Installation is done by a down-the-hole (DTH) hammer using the centric drilling system and oversized ring bits or a drilling system consisting of a pilot bit and reamer wings shown in Fig. 2."

Jan 1, 2017

By Ezz El Din Abdel Hakim Khalaf, Khalid S. Essa, Marc Munschy, Mohamed A. S. Youssef

This study focused on joint interpretation of the aeromagnetic and radiometric data to allocate and describe the structural elements and mineralization zones such as uranium, gold, and sulfide in the Gebel Umm Tineidba and its surroundings, Eastern Desert, Egypt. The study region is covered by exposures of Precambrian rocks such as gneisses, migmatites, ophiolitic mélange, metavolcanics, younger granites, and Quaternary sedimentary covers. The application of the total intensity magnetic and reduced-to-pole maps, power spectrum, analytic signal, tilt-angle, and local wavenumber maps helps in recognizing magnetic sources distribution, lineament features, and mineral zones delineation. The obtained results indicate that the depths of the deeper NE–SW, NNE–SSW, and N–S trending structures extend from 400 to 1750 m and shallower ones range from 100 to 400 m. Finally, the main trends of these structures affect the probable mineralization zones.

Sep 22, 2022

By L. H. Wullstein

Nitrogenase activity (C2H2 reduction) was found to be associated with the following grasses in the field: Agropyron dasystachyum, Agropyron smithii, Aristida purpurea, Oryzopsis hymenoides and Stipa comata. Uptake of fixed nitrogen was also demonstrated for these grasses. Two unidentified nitrogen fixing bacteria were isolated, one from Stipa comata and one from Aristida purpurea. Cynodon dactylon and Agropyron cristatum were successfully inoculated with the unknown isolate obtained from Stipa comata. The inoculated plants exhibited nitrogenase activity (C2 H2 reduction) whereas uninoculated controls gave negative results.

Jan 1, 1982

By Dharmendr Kumar, Pradip, Sivakumar Subramanian, Beena Rai, Venugopal Tammishetti

The separation efficiency in a mineral processing plant is generally assessed and reported in terms of elemental assays constituting the minerals of interest. However, different minerals comprising of same elements behave differently under similar process conditions. Thus, it is imperative to track the mineral composition thank elemental composition of different streams in a processing plant. The availability of automated mineral analyzers such as QEMSCAN and TESCAN in recent times has made it possible. However, due to the high cost and expertise required, their adaptation in day to day monitoring of operations is not yet a common place. X-ray diffraction (XRD) profile fitting (Rietveld Refinement) is another technique which can provide estimates of mineral proportions in a sample. The results of Rietveld Refinement however are affected by coating of fines on coarse particles, method of sample preparation, particle size distribution of sample, elemental substitution in mineral crystal lattice. In the present work, we propose a simple and efficient method for quantitative estimation of minerals in iron ores using elemental assays and thermo-gravimetry analysis data. The minerals (hematite, goethite, gibbsite, kaolin and quartz) are identified using powder XRD analysis. It is also observed that goethite contains Al substitution in the crystal lattice. The samples were analyzed for %Fe, %Al2O3 and %Silica using chemical analysis. The measured Loss on Ignition (LOI) in the sample is contributed from goethite, gibbsite and kaolinite phases. LOI from gibbsite and goethite occur in temperature range 250–350°C and LOI from kaolinite occur in temperature range 400–700°C. According, LOI are determined in two different temperature ranges that are 100–400°C and 400–850°C. We have used the data to successfully determine the mineral compositions of iron ore samples. We have also employed a data reconciliation algorithm on the calculated data for further improvement and consistency of our results. Our method is very convenient for quick estimation of mineral proportions in a sample. The proposed method can also be used for quantitative phase estimation in bauxite ores and red muds.

Jan 1, 2016

By Edward Halse

THE occasional occurrence in metalliferous veins of rounded fragments of rock, matrix or ore, lying loose, embedded in clay, or enclosed in some kind of cement, may be attributed to four causes:¬ I. They have been washed in from the surface, or from an upper portion of the vein. II. They are of concretionary origin. III. They have been produced by movements in the country-rock or in the walls of the vein. IV. They have been found in situ, by the upward, downward or lateral flow of water in the vein itself. In this paper the word " conglomerate " is confined to a rock composed of rounded fragments or pebbles cemented together, as distinguished from a " breccia," in which the rock-fragments are angular. I. BOULDERS AND PEBBLES WHICH HAVE BEEN WASHED IN FROM THE SURFACE, OR FROM AN UPPER PORTION OF THE VEIN. In this type it is presupposed that the vein at onetime com¬municated by a fissure or open space with the surface, or with the upper portion from whence the fragments have been washed. One well-authenticated occurrence was described long ago by Fournet. Owing, no doubt, to later dislocations in the lode, pebbles from an old alluvium and sands containing titaniferous iron, as well as fragments of wood, were found in a vein at Huelgoët, in France. "Toutes les parties tendres du filon de Pranal ou ces pédnomènes sont les plus prononcés ont été excavés jusqu'a d'assez grandee profondeurs par l'impétuosité des torrents, qui ont deposé la matière alluviale."1

Jul 1, 1905

By E. Ghali, W. Zhang, G. Gabra, N. Sorour, G. Houlachi

The additives polyacrylamide, 1-Butyl-3-methylimidazolium chloride, Tetra-butylammonium bromide, Benzalkonium chloride and chitin are evaluated during zinc electrolysis from synthetic acidic sulphate electrolyte containing Mn2+ ions, in absence and in presence of 0.0055 mg dm-3 of Sb3+ ions. Galvanostatic polarization tests for 2 hours at 50 mA cm-2 and 38oC were carried out to determine the cathodic and anodic potentials, and current efficiency of the deposited zinc. Potentiodynamic polarization and cyclic voltammetry tests have also been employed to study the electrochemical behavior of each additive on the zinc deposit on aluminum electrode. Results showed that, in presence of Sb3+, adding 1 to 3 mg of 1-Butyl-3-methylimidazolium chloride increases the cell voltage by ˜0-7 mV. Current efficiency is increased by ˜4.90-6.40%; power consumption is reduced by ˜147-173 kWh t-1 by adding 1-3 mg, respectively. However, in absence of Sb3+, cell voltage is decreased by ˜7-28 mV, current efficiency is increased by ˜0.70-1.50%; power consumption is reduced by ˜41-47 kWh t-1 by adding 1-3 mg. The effect of the other additives on cell voltage, current efficiency, lead content and morphology of zinc deposit has also been examined. Surface morphology and crystallographic orientation of the deposit was studied using scanning electron microscopic (SEM) and X-ray diffraction (XRD), respectively. The content of lead in the deposit has also been measured using inductively coupled plasma spectroscopy (ICP).

Jan 1, 2015

By Andrew Malinak, William Perkins

Seattle’s Elliott Bay Seawall protects the 1½ miles of downtown waterfront between South Washington and Broad streets. The seawall supports the urban waterfront and infrastructure, including the Alaskan Way Viaduct and Alaskan Way, access to historic waterfront piers, and numerous essential buried utilities. Most of the original seawall was constructed between 1916 and 1936 over soft/loose non-engineered fill, estuary, and beach deposits. The majority of the original seawall was a pile-supported timber relieving platform that extended up to 60 feet behind the face of the wall (Figure 1). With maximum spacing between the timber piles of 3 to 5 feet, a virtual forest of timber piles were driven for the original wall.

Jan 1, 2018

By A. Kalogeropoulos, T. Michalakopoulos

The DEM has been used in several studies to numerically simulate the response of rocks to the cutting action with drag tools. In this research, the aim is to realistically simulate the rock material and the cutting process by controlling the grain interlocking of the numerical assembly and streamlining the calibration process while focusing on the cutting force and the failure mechanism.

Apr 1, 2023

By George T. Faust

The petrographer engaged in examining the products resulting from the beneficiation of ores, and rock minerals is constantly required to develop new means acid methods of assaying microscopically the results of such operations. From time to time investigators have published descriptions of apparatus that have aided in solving problems in processes of physical separation. Thus, in 1919, Coghill and Bonardi 3/ published a paper covering the application of the binocular microscope and camera lucida to the microscopic analysis of pulverized ores. Similar work has been published by Schneiderhohn 4/ Schwartz 5/, and Head and his associates 6/, 7/, 8/. The present paper goes further and considers application of the polarizing comparison-microscope to problems directly concerned with mineral dressing where it is desirable to compare analogous products, and in addition it suggests new uses in various related fields. This work was conducted under the cooperative agreements of the Southern Experiment Station of the Federal Bureau of Mines and the University of Alabama.

Jan 1, 1940

By R. V. Ramani

This report is volume 10 of an eleven-volume final report for a Grant completed by The Pennsylvania State University for the Bureau of Mines to develop a dynamic general purpose computer simulation model for underground coal mining. The simulator developed under the Grant has a wide range of possible applications in the design and evaluation of underground coal mining systems from the standpoints of health and safety, productivity, and mine environment. The Master Design Simulator consists of nine free-standing function-oriented subsystem models linked together into an integrated, comprehensive model of an entire mining system. The subsystems comprising the Master Design Simulator include geology and reserves, methane generation, roof support, subsidence, production, rail haulage, cost, water generation, and ventilation. This volume of the final report describes the Ventilation subsystem of the Master Design Simulator. The Ventilation subsystem has the capabilities to handle: (1) branches in parallel or series, (2) fans in parallel or series, (3) multiple fans, (4) methane, compressed air, or other injections into the system, (5) leakages and fixed quantities, and (6) calculations of absolute pressure at nodes. The program uses the Kirchoff's Junction and mesh laws, and the Hardy-Cross iterative technique to converge to the desired accuracy in solving fox the head quantity. A case study is included in the report illustrating the use of the model. The appendices of the report constitute a user's manual for the Ventilation subsystem, and include a program listing.

Jan 1, 1975

By Patrick Fantin

Mining ? The Past Safety Not a priority; Health Not a priority; Energy Manual Labour; Horsepower? Literally. Financially Robust For the Owner?s; Mining ? The Future Safety Zero Harm Health Understanding and elimination of Industrial Disease Energy Efficient use of energy through technology. Full value of renewable energy. Financially Robust Continually build shareholder value through optimum CAPEX/OPEX.

May 1, 2013

By Edwin B. Wilson, Charles F. Cockrell

The application of evolutionary operation is proposed for the cleaning of coal by the heavy media process. Analysis of the data given suggests some benefits that may not be immediately appreciated unless evolutionary operation is applied. For example, while it may seem obvious to increase specific gravity when the ash and sulfur content of the clean coal is lower than that allowed, evolutionary operation may show that an increase in feed rate or an increase in both feed rate and specific gravity would be a more profitable alternative. In addition, by using evolutionary operation, up-to-date knowledge of the effect of change of feed rate or specific gravity on yield and product quality is available. This information facilitates confidence about decisions made in regard to the day-to-day operation of these units. A number of other applications in the minerals industry are proposed. An application of evolutionary operation in a related field is also given where a large number of variables were required to be optimized.

Jan 1, 1969

By R. P. Vinson

Assessment of workplace exposures is an important tool for helping to minimize dust-related occupational illness and diseases. Real-time particulate monitoring can effectively locate areas where dust controls are needed and determine how well they are working. An affordable, person-wearable, real-time dust monitor is needed. The SKC Inc. Dust Detective (SKCDD) fulfills those requirements (Disclaimer: Mention of any company or product does not imply endorsement by NIOSH). The SKCDD consists of a disposable sampling tube (DST) connected to a small hand-held sampling pump. The SKCDD was developed through a Cooperative Research and Development Agreement (CRADA) between the National Institute of Occupational Safety and Health (NIOSH) and SKC Inc. The relationship of dust concentrations measured by personal gravimetric samplers to those measured by the SKCDD was determined in a laboratory aerosol chamber. A comparison of the means and the relative standard deviation of triplicate measurements of each type of sampling device demonstrated the SKCDD to be a viable alternative means for measuring dust. While it provides accurate measurements for specific coal types, it requires correction factors (those correction factors still need to be calculated) for other coal types.

By D. J. Dollhopf

An overburden handling dragline operation was conducted at a strip mine near Colstrip, Montana. The objective of the demonstration was to determine the degree a dragline could mix overburden inhibitory zones during the spoiling process. In order to quantify the mixing process the overburden was: 1) scatter spoiled; 2) dump spoiled; and 3) spoiled in a normal manner. This demonstration was part of an effort to investigate means of reestablishing non-polluted hydrological systems in areas where surface mining directly impacts shallow ground-water resources. When inhibitory material constituted < 5% of the total overburden volume, such material was essentially not detectable in the resultant spoil pile. When inhibitory material exceeded 15% of the overburden volume it was always found in the resultant spoil pile, generally with a smaller extent, indicating partial dilution. Inhibitory overburden zones often reappeared at the base or top of spoil piles in the potential aquifer and root zones suggesting the need for selective placement procedures. Scatter spoiling did not appear to be significantly more effective than normal spoiling, however clump spoiling seemed to produce less mixing of inimical zones. Mining activity has reduced ground-water levels within 1600 m of the active pit. The aquifer which is developing in spoils appears to have similar confinement characteristics as those that existed in the premined aquifer. To date no definite trends have been observed concerning changes in surface or ground-water chemistry associated with mining.

Jan 1, 1978

By Joseph M. Kuchta

The limits of flammability and minimum autoignition temperature of a fuel are important elements in assessing fire and explosion hazards that may exist when using or handling the fuel. The limits of flammability define the range of compositions of the fuel gas or vapor mixed with an oxidant through which a flame, initiated by an outside energy source such as an electrical spark, can propagate. The minimum autoignition temperature (M.A.I.T.) is the lowest temperature at which the fuel vapors ignite spontaneously in a specified medium; in this case the ignition energy is supplied by the heat content of tae environment. This temperature is also referred to as S.I.T. value by some authors. Because the autoignition of a fuel also depends on the time interval during which the fuel is subjected to heat, ignition delays are significant. Ignition delay is defined here as the total time elapsed between the introduction of the liquid fuel into the oxidizing atmosphere and the appearance of a flame. This time interval includes both the physical and chemical processes leading to ignition. The ignition delay is usually maximum at the M.A.I.T, and decreases as the temperature of the system is increased. The flash point and the fire point are also useful in assessing the fire and explosion hazards of a fuel. The flash point is the lowest temperature at which saturated, flammable fuel vapor-air mixtures are formed at atmospheric pressure and, therefore, it is essentially the lower limit of flammability

Jan 1, 1962

By Alfred Petrick

This study gives an analysis of the copper system byproducts and discusses the identification and classification of byproduct metals and their supply systems. Arsenic, platinum-group metals, silver, gold, selenium, tellurium, molybdenum, rhenium, uranium, aluminum, magnesium, and byproduct copper, lead, and zinc from complex ores are covered. The report describes several metallurgical systems, the marginal and incremental products costs of byproduct subsystems, industry structure and organization, and the historical data on price, consumption, and supply. Supply curves are presented for about one-half of the byproduct metals studied. The study develops a conceptual framework for analysis by reviewing the present concepts of byproduct supply and the related price theory. It gives the sources of supply of the individual byproduct metals to indicate the importance of the byproduct supply to the total supply. Mills, smelters, and refineries processing byproduct materials for their metal content are identified by geographic location and company ownership, The study also includes information on the reserves-resource base supporting byproduct output, reserve estimates, and the demand aspects of each byproduct metal.

Jan 1, 1973

By Byron T. Darnton

Gravity concentration at the Pegasus Gold/Montana Tunnels Mine, near Helena, MT, began in June 1991 when a coarse-gold-scalping circuit was commissioned. It processes a small portion of the ball-mill circulating load to reduce the risk of gold particles that are too coarse to float from advancing to flotation. The circuit also cost-effectively enhances overall gold recovery and payable gold ounces. This gravity circuit has been a major success. Since the circuit was commissioned, throughput has increased 30%. Several modifications and improvements were made during the last three years that allowed the gravity circuit to keep pace with the higher tonnage. The overall approach to gravity concentration at Montana Tunnels has always been to optimize production rather than maximize the gold ounces produced. This philosophy has now yielded a circuit expansion and relocation project. It will allow for an estimated 50% increase in gravity gold production, while significantly reducing the unit costs of production.

Jan 1, 1995

By Ming-Gao Qian

How to monitor and control the support and surrounding strata system on a longwall face effectively is one of the major research problems in ground control. Based on observations on movements of the support and surrounding strata of face No. 2703 of Dongpang colliery, the relationship between the downtime related to support and surrounding strata and other influential factors is analysed systematically in this paper. Monitoring indices and control measures are then determined by taking corresponding downtime as an objective function. When the monitoring method, developed from the above findings, was used on face No. 2703, the downtime due to support and surrounding strata was remarkably reduced, and the face advanced normally.

Jan 1, 1992

By T. D. Parris

Within a 30-mile radius of Sudbury, Ontario, the Ontario division of the International Nickel Co. of Canada, Ltd., operates nine underground mines and two open pits. Prior to 1966, ore removal from the underground workings was mainly by scraping, using 125-hp electric slushers in blasthole and caving mining, and 30-hp or less air-operated slushers for fill- method mining. The development and evaluation of low-profile, diesel-powered front-end loaders, designed specifically for underground operations, was followed with keen interest during the period 1964-1965.

Jan 6, 1969

By James Ridenour

This report represents the first comprehensive accounting of lode mining sites in the Loon Creek mining district, Custer County, Idaho. Thirty-five mine and prospect locations have been added to the Bureau&apos;s Mineral Industry Location Subsystem (MILS) data base as a result of initial phases of a mineral appraisal of the River of No Return Wilderness; previously known locations were field checked and the updated information added to the data base. The district&apos;s major deposits are gold-copper-silver fissure-fillings hosted by biotite schist intruded by dikes ranging in composition from rhyolite to lamprophyre. These deposits contain a trace element suite similar to Tertiary pink granites and may be related to intrusion of the nearby Casto pluton. Continued firm gold prices could stimulate the search for precious metal occurrences in this and other mining districts in central Idaho.

Jan 1, 1983