Search Documents

By D. J. Esdale, D. F. Pridmore, F. W. Lindman, J. H. Coggon

Almost all the presently viable nickel reserves in the Yilgarn Block contain nickel in a sulphide phase. Both volcanic peridotite- associated (VPA) deposits and intrusive dunite-associated (IDA) deposits are characterized by massive, matrix and disseminated sulphides (typically, pyrrhotite, pentlandite, pyrite, chalcopyrite, magnetite and other spinels), though in the IDA deposits the volume of disseminated sulphides is far greater than that in the VPA deposits. Potentially all geophysical techniques have application in the direct detection of these deposits'gravity for the detection of the dense massive and matrix ore; magnetics for the detection of magnetite and pyrrhotite in the ores; electromagnetics for the detection of the massive and matrix ore; and induced polarization for the detection of disseminated and to some extent matrix and massive ore. In practice the application of geophysical techniques is limited to a varying extent by (1) the relatively small size of an economic accumulation of sulphides, particularly the VPA deposits, (2) the extreme depth of weathering and lack of outcrop on the Yilgarn Block and (3) the abundance of geological noise or anomalous responses caused by sources other than economic mineralization.

Jan 1, 1984

By Mike Turner

The Otter-Juan mine was closed by WMC Resources? Kambalda Nickel Operations (WMC-KNO) in 1999 due to the combined effects of low Nickel prices and high mining costs. GBF Mining Pty Ltd purchased Otter-Juan Mine from WMC in early 2001 as part of WMC?s disinvestment from the nickel mines in the Kambalda area. Goldfields Mine Management (GMM), (a wholly owned subsidiary of GBF Pty Ltd) re-opened Otter-Juan in May 2001. The Otter-Juan mine is one of the oldest mines in the Kambalda region and is now mining at depths below 1160mbs. Stresses are very high, rock mass deformation considerable, and the mine has a history of serious seismic activity. Orebody widths in the current mining area range from 2 to 2.5m, with dips from 25° to 40°. On taking over the operation, GMM converted the mining method from the previous mechanised drift and fill method to a slot-rise and strip method using hand held airlegs. During the latter years of production under the control of WMC, production averaged around 12000 tonnes per month, with grades of 2.7% and orebody extraction of only 55 to 60%. In the last three years of operation under the control of GMM the mine has produced an average of 12000 tonnes per month of ore at an average grade of 4.2% and with an orebody extraction of 70 to 75%. The mine is now highly profitable with at least another 3 years of reserves remaining at depth. The main benefits of the current method include reduced dilution and increased extraction. In the relatively poor ground conditions experienced this has only been possible using airleg mining, with excavations designed to suit conditions, support to suit rockmass deformations, and with improved extraction sequencing. Other benefits have included improved operating conditions, reduced falls of ground incidents and a dramatic reduction in seismic activity. These achievements have only been possible by stepping back in time and using traditional airleg stoping methods to extract the maximum amount of the orebody with minimum dilution. This paper includes details of the mine history, geology, mining method, seismicity, and support.

May 1, 2004

By F. Ntengwe

The Konkola Mine, a subsidiary of the Konkola Copper Mines Plc (KCM) which is owned by the Vedanta group of companies of India and Zambia Consolidated Copper Mines Holding limited, is located at Chililabombwe in the northern extension of Zambia's Copperbelt province. In its operations, the mine has been experiencing problems in ascertaining the optimum degree of fineness and the operating density of the hydrocyclone overflow in order to achieve high flotation performance. It was believed that recovery of sulphide copper minerals from Konkola ore is a function of the fineness of the grind so that it might be an economical justification to modify the grinding plant in order to run at lower cyclone overflow densities than the case is now. In an effort to improve these operations, it was decided to carry out test work on various hydrocyclones of sizes 0.381 m, 0.4575 m and on 0.508 m. The later was found to give satisfactory results and was installed on the plant. Despite giving satisfactory results there was need to investigate further to establish the working densities and size. Increasing the density of cyclone overflow decreases the per cent passing 75 pm at least in the range 1080-1 150 g/l. Furthermore, hydrocyclones give better separation at low densities of feed and hence the efficiency is high at low feed densities. Circulating load increases with an increase in feed densities and an decrease in the grind. The flotation performance in both sulphide and oxide copper minerals rougher stages is enhanced with an increase in the degree of fineness of the grind, with an optimum being obtained at a density of 1 150 g/l and 81.4% passing 75 µm. Keywords Konkola mine, hydrocylone, optimum degree of fineness, sulphide copper minerals.

Jan 1, 2011

Your assessment of the minerals business. The global mining industry is strong. I am convinced it will continue meeting the mineral needs of the world population for the foreseeable future. Two developments have greatly enhanced the industry’s ability to produce low-cost minerals. Technological innovations have resulted in increased productivity. And there has also been a dramatic expansion of the number of favorable countries in which to explore and mine. Capital expenditures have flowed to the low-production-cost mines and development projects as well as to the exploration projects and stable countries having the best potential for valuable mineral discoveries.

Jan 1, 2000

By Simon Lekakh, Von Richards, C. Hank Rawlins, Kent Peaslee

"Batch aqueous leaching and carbonation tests were conducted using industrial steelmaking slags to determine the effect of carbonic anhydrase enzyme as a catalyst. Calcium leaching is a strong function of particle surface area, and the extent can be expressed as a function of time and particle size. Carbonic anhydrase did not affect the calcium-leaching rate, however, it did catalyze calcium carbonate formation to achieve a neutralization time near the theoretical rate. Additionally, carbonic anhydrase modified the precipitate morphology due to accelerated particle nucleation. Time controlled tests in which the pH dropped to ~6 decreased the amount of carbonate produced, and this effect was exaggerated by carbonic anhydrase, while pH controlled tests (>8.5) exhibited the highest rate of carbonation. Because the leaching rate was ~50% faster than the carbonation rate, a further increase in the amount of carbonation may be realized by using carbonic anhydrase however pH must be >10.3.IntroductionSteelmaking slag contains high fractions of alkaline earth oxide based phases (i.e., CaO and MgO) that exothermically form carbonates. Thus, it is being considered as a means of permanent carbon dioxide sequestration. At current U.S. steel production rates, approximately 13-17 million tons/year of slag are generated from basic oxygen furnace (BOF), electric arc furnace (EAF), and ladle metallurgy furnace (LMF) processes [1]. BOF and EAF slag is used as high quality mineral aggregate or cement clinker, while LMF slag, produced at ~15% the rate of BOF and EAF slags, has limited use as blast furnace flux or acid mine neutralization with the majority going to landfill [2]. Based on slag’s chemical nature and immediate availability as a co-product from steel production, the steel industry initiated a project to investigate hydrous carbonate formation in steelmaking slag as a method of sequestering carbon dioxide emitted in steelmaking offgas [3]. The goal of this project is to determine the reactor parameters suitable for the design of an industrial system for treating steelmaking offgas with raw or minimally processed slag."

Jan 1, 2009

By Leandro Nakamura Alves Vieira

O acirramento da competição no mercado de aço tem exigido esforços de inovação e redução de custos. Por sua vez, as técnicas agrupadas como ICME - Integrated Computational Materials Engineering vêm acelerando o desenvolvimento e a otimização de materiais e processos de fabricação. O emprego destas técnicas tem sido uma ferramenta extra para assegurar a competitividade na indústria. Neste trabalho o uso da termodinâmica computacional no desenvolvimento e processamento de aços elétricos é revisado através da discussão de exemplos. Cálculos de equilíbrios mais relevantes para o processo de fabricação destes aços (tanto de grão não orientado-GNO como orientado-GO) permitem obter informações sobre as transformações de fases, solubilização de precipitados (sulfetos e nitretos) essenciais para a obtenção de texturas cristalográficas ideais. Os cálculos são discutidos e comparados com resultados reais. Discutem-se ainda, cálculos no sistema aço-gás, e os efeitos da composição da atmosfera na formação de óxidos na superfície do aço. Tais cálculos são importantes para descrever previamente as transformações que ocorrem durante as várias etapas de fabricação, assim como os efeitos dos parâmetros de processo sob os aços elétricos. A aplicação da técnica permite otimizar o processamento e o desenvolvimento dos aços elétricos em diversos aspectos. As vantagens e limitações do método, assim como o potencial de outras técnicas de ICME, na área, são discutidas.

Aug 7, 2018

By Joan Weinberg

Real gross national produce (GNP) grew at a seasonally adjusted annual rate of 2.0% in the fourth quarter (table 1). The restrained quarterly growth rate was the slowest in 2 years, and was substantially slower than the 2.5 % rate of the previous quarter. According to the U.S. Department of Commerce, the summer drought reduced the fourth-quarter growth rate by 1.1 percentage points. A growing trade deficit and a reduction in business investment were the key economic factors curtailing growth. The trade deficit widened by $6.8 billion, reflecting both a surge of imports and a slowing of exports. Business investment declined 3.7%, mainly as a result of a slowdown in computer sales. On a year-to-year basis, the economy grew at an inflation-adjusted rate of 3.8% for 1988, the fastest in 4 years, despite the drought. However, on a fourth-quarter-to-fourth-quarter basis, real growth measured 2.7%. Increased exports and business spending for plant and equipment accounted for much of the 1988 GNP growth. Employment continued to grow as the manufacturing sector added 414,000 new workers (table 2). Of these, the primary metals industry added 26,000 workers, and the clay, glass, and stone industry added 10,000. The civilian unemployment rate remained low throughout 1988, fluctuating between 5.3% and 5.4% during the last quarter.

Jan 1, 1989

By J L. Mauk

Gladstone Hill, a volcanic-hosted low-sulfidation epithermal prospect in the Coromandel Peninsula, is less than 1 km from the world-class Martha Hill Au-Ag deposit. Gold-silver-bearing quartz veins occur in Late Miocene andesitic volcanic rocks of the Waipupu Formation that are extensively altered. The occurrence, spatial distribution and temporal relationships of hydrothermal minerals have been determined along two cross sections that transect the Amaranth, Gladstone, Cowshed and Moonlight veins. Quartz and pyrite are ubiquitous along these sections. Adularia and chlorite are widespread, but both are scarce in wall rocks adjacent to the Moonlight and Cowshed veins. By contrast, rare hydrothermal albite and epidote are restricted to wall rocks surrounding the Amaranth vein. Illite, which replaces adularia, is widespread and grades laterally eastwards into a zone of interstratified illite-smectite that envelops the Moonlight and Cowshed veins. During late-stage hydrothermal activity, rare calcite formed at depth and uncommon kaolinite and alunite formed at shallow levels. The overall clay mineral zonation with illite grading eastward into interstratified illite-smectite reflects paleothermal gradients of >220¦C to -170¦C towards the margin. The alteration assemblage of quartz, adularia, chlorite, albite, epidote, illite, interstratified illite-smectite and pyrite reflects formation from a near-neutral to weakly alkaline pH chloride water that contained low concentrations of CO2, Late calcite formed from very local descending steam-heated CO2rich water, whereas the rare assemblage of kaolinite and alunite formed from shallow steam-heated acid-sulfate water. Analysis of the available data indicates that the Martha Hill deposit and the Gladstone Hill area formed within a single large geothermal system. We infer that the Martha Hill deposit formed in the main upflow zone, whereas the Gladstone Hill area may have formed adjacent to this upflow zone.

Jan 1, 2001

By Adauto Martins de Assis, Atan de Assunção Cardoso

Devido a sua alta demanda de produção e padrão de qualidade a indústria automotiva tem utilizado ao longo da história robôs nas mais diversas atividades como montagem, soldagem, pintura e inspeção. No intuito de levar esta realidade para a sala de aula de alunos de Engenharia Mecânica, foi desenvolvido um braço robótico didático, apresentando configuração semelhante à um modelo industrial, a ser utilizado como ferramenta de apoio ao ensino de robótica e outras disciplinas correlacionadas. Para isto, fez-se o uso associado da placa eletrônica Arduino e do software Matlab. Inicialmente foram obtidas as equações de cinemática direta e inversa. Os resultados mostraram que a posição teórica obtida apresentou um comportamento esperado conforme a metodologia adotada e o resultado experimental mostrou pequena variação de posição. Para a cinemática inversa, o tempo de resolução do conjunto de equações foi comparado à resolução do problema através de um método numérico. Com base nos resultados experimentais, foram feitas algumas sugestões de melhoria para o braço robótico didático e considerações relacionadas a acurácia de um robô industrial.

Oct 1, 2019

By A. F. Grandt

What is prime farmland? Can such land, once it has been strip-mined for coal, be restored so that it will produce corn, soybeans, wheat, and alfalfa? What methods or practices are necessary to bring about restoration within a reasonable time so that crop yields will be equivalent to or higher than those of unmined prime farmland under high levels of management? These questions concerned land use researchers in Illinois as early as 1948 when the Illinois Agricultural Experiment Station experimented with growing cultivated crops on strip-mined land in St. Clair County (1). This research was done almost 30 years before requirements of Public Law 95-87 were passed by the United States Congress and signed August 3, 1977.

Jan 1, 1980

By Earnshaw Cook, J. A. Fellows, Howard S. Avery

Heat-resistant alloys of the higher nickel and chromium ranges have been empirically developed through the practical experience of the past two decades to a position of significant industrial importance. Few quantitative metallurgical data have been published, however, that could be related directly to engineering specifications and design. Inadequate information led to the inauguration, in 1934, of a research directed toward a better understanding of the properties and performance of these steels at temperatures between 1400° and 2000°F. Investigation was concentrated upon the 26 per cent Cr:I2 per cent Ni type, which owes its extensive application to an excellent combination of economy, strength and surface stability at elevated temperatures. The requirements of the oil-refining industry have been prominent in influencing the scope and evolution of the program. Creep strength at the maximum allowable deformation ranges has been employed to evaluate the merits of these alloys. Permissible elongation rates vary from 1.0 per cent in one million hours for turbine blades to I .o per cent in ten thousand hours for tube supports and heating-furnace equipment. Throughout this paper, the limiting creep stress (L.C.S.) for a given temperature has been defined as the stress that will produce a uniform elongation rate (stage 11) of one per cent in ten thousand hours as extrapolated from rates per hour for tests of less than two thousand hours duration. Certain current specifications require a minimum L.C.S. of 1600 lb. per sq. in. at I800°F., of 3600 lb. per sq. in. at 1400°F., and include a tensile acceptance test at room temperature, after aging for 24 hr. at 1400°F., as a measure of embrittlement in service. An elongation of 4 per cent is considered satisfactory for general use, while a minimum of 9 per cent is prescribed on occasion. Many differences of opinion concerning the properties and performance of these alloys appear to result from their sensitivity to unappreciated variations of chemical analyses which, for example, may change their L.C.S. from 3500 to 350 lb. per sq. in. at 1800°F. Within broad chemical limits, it is possible to balance the six or more important elements present to attain desirable properties with a number of different combinations. One method for adjusting the composition has been described under the sponsorship of the Alloy Casting Institute,' in which, by maintaining a substantially austenitic* alloy, optimum creep strength and minimum tendency to embrittle after aging are expected. Unless, however, the limits are undesirably close, it has not been possible to ensure a moderate range of strength and of ductility by any chemical specification alone. There is a definite need

Jan 1, 1942

By J. A. Fellows, Earnshaw Cook, Howard S. Avery

Heat-resistant alloys of the higher nickel and chromium ranges have been empirically developed through the practical experience of the past two decades to a position of significant industrial importance. Few quantitative metallurgical data have been published, however, that could be related directly to engineering specifications and design. Inadequate information led to the inauguration, in 1934, of a research directed toward a better understanding of the properties and performance of these steels at temperatures between 1400° and 2000°F. Investigation was concentrated upon the 26 per cent Cr:I2 per cent Ni type, which owes its extensive application to an excellent combination of economy, strength and surface stability at elevated temperatures. The requirements of the oil-refining industry have been prominent in influencing the scope and evolution of the program. Creep strength at the maximum allowable deformation ranges has been employed to evaluate the merits of these alloys. Permissible elongation rates vary from 1.0 per cent in one million hours for turbine blades to I .o per cent in ten thousand hours for tube supports and heating-furnace equipment. Throughout this paper, the limiting creep stress (L.C.S.) for a given temperature has been defined as the stress that will produce a uniform elongation rate (stage 11) of one per cent in ten thousand hours as extrapolated from rates per hour for tests of less than two thousand hours duration. Certain current specifications require a minimum L.C.S. of 1600 lb. per sq. in. at I800°F., of 3600 lb. per sq. in. at 1400°F., and include a tensile acceptance test at room temperature, after aging for 24 hr. at 1400°F., as a measure of embrittlement in service. An elongation of 4 per cent is considered satisfactory for general use, while a minimum of 9 per cent is prescribed on occasion. Many differences of opinion concerning the properties and performance of these alloys appear to result from their sensitivity to unappreciated variations of chemical analyses which, for example, may change their L.C.S. from 3500 to 350 lb. per sq. in. at 1800°F. Within broad chemical limits, it is possible to balance the six or more important elements present to attain desirable properties with a number of different combinations. One method for adjusting the composition has been described under the sponsorship of the Alloy Casting Institute,' in which, by maintaining a substantially austenitic* alloy, optimum creep strength and minimum tendency to embrittle after aging are expected. Unless, however, the limits are undesirably close, it has not been possible to ensure a moderate range of strength and of ductility by any chemical specification alone. There is a definite need

Jan 1, 1942

By Dapeng Zhang, Brij Moudgil, Shibo Zheng, Chunhui Feng, Wenyi Song, Wending Xiao, Patrick Zhang

The separation of dolomite from phosphate is the most challenging problem in phosphate mineral processing. More than 50 percent of the phosphate reserve in Florida contains too much dolomite to process using current industry practice. The current way of producing phosphoric acid requires less than one percent MgO in the phosphate concentrate as the feed material. The Florida Industrial and Phosphate Research (FIPR) Institute has collaborated with worldwide experts in the field to address this issue. As a result, the industry is now offered three feasible options. Option I entails three methods for reducing MgO content in the concentrate from the Crago process, including adding a dolomite depressant in the rougher flotation step, dolomite flotation of the cleaner concentrate, and scrubbing the cleaner concentrate in quartz sand, which could reduce MgO content in the final concentrate by 20 to 40 percent. Option II involves the crushing and grinding of high-dolomite phosphate pebbles followed by dolomite flotation at slightly acidic pH using a new collector that does not require phosphoric acid as a phosphate depressant, achieving a final concentrate analyzing less than 0.9 percent MgO at about 87 percent P2O5 recovery. Option III is a gravity separation technique using an innovative separation jig, and its full potential remains to be demonstrated.

By Pratoomkhuan N. Lertsgoon

A large underground cavern with dimensions of 25m × 175m × 49m (W×L×H) was excavated in sandstone and siltstone to house 4 units of hydropower generator and was completed in 2000. In feasibility study stage, the property of the siltstone which governs the ceiling of the cavern was questionable due to slaking phenomenon. Parameters on rock properties for design were back calculated from actual ground response measured from a trial excavation. For safety of construction, comparison between prediction and actual ground responses during excavation had proceeded. The prediction was provided by means of PHASES and PHASE2 software and the actual rock response was detected by the provided monitoring system.

Jan 1, 2003

By Edward Hart

Having occasion several years since to make ferrous sulphide, I attempted to do so by fusing a mixture of coal-brasses (FeS2) and dried ferrous sulphate. A very nice-looking sulphide was obtained; but on attempting to use it, I found that it was insoluble in dilute hydrochloric and sulphuric acids. The subject was laid aside at the time, but has since been taken up; and some curious results have been obtained, which I believe are new. I have made the material by all of the following methods and the product seems to be pretty much the same, however obtained : (a) FeS2 heated to fusion. (b) FeS2, and FeSO4 heated to fusion. (c) FeS2, and Fe2O3 heated to fusion. (d) FeS2, and FeCO3, heated to fusion. (e) FeSO4, and S heated to fusion. (f) Fe2O3 and S heated to fusion. Obtained in this way the mass after cooling breaks easily and is very nearly black in color. On the upper surface of the fused cake the color is generally reddish or brownish black. When this is treated with dilute sulphuric or hydrochloric acid, it refuses to dissolve; but if touched with the point of a file or any piece of wrought-iron, solution of the sulphide takes place with the evolution of sulphuretted hydrogen. If the iron is removed the evolution of gas ceases, and only begins again when the iron is again brought into contact with the fused sulphide. The same thing happens if the iron is connected with the sulphide by means of a platinum wire. But in all the samples of fused sulphide I have obtained, if the iron is allowed to remain in contact with the sulphide for a certain time (which varies with different samples of the fused sulphide) and is then removed, solution of the sulphide continues. Zinc, tin, and magnesium have the same effect as iron. In hydrochloric acid aluminium acts more rapidly even than iron. In sulphuric acid it has little if any effect. Copper in HCl, when brought in contact with the fused sulphide, dissolves quietly without evolution of gas. The solution of copper chloride formed becomes,as it flows down over the sulphide, converted into copper sulphide.

Jan 1, 1887

By Matthew Violot

Introduction ?Located off highway 6, approximately 5 km, SW of Thompson, Manitoba ?Base metal mine: Nickel? Maximum Depth: 4100 ft ?Started Production in 1966 (INCO, 2006)?Halted in 1978?Re-opened in 1989 ?Two types of mining:?VBM (vertical block mining)?Cut and Fill 1.1 Problem ?Birchtree mine is experiencing failures and undesirable dilution in some of their stopes. ?Time can have a large effect on open stopestability. ?Birchtreeis interested in how time is affecting the stability of their stopes. ?The study focuses on the lower 84 complex, which extends from 2750 to 4100 foot level.

Nov 1, 2011

By Elisiane Maria Berton

Neste trabalho propõe-se o estudo do efeito do processo de SHTPN (Tratamento térmico de solubilização após nitretação por plasma), e do tratamento térmico de têmpera e revenido sobre a microestrutura, dureza e resistência à corrosão do aço inoxidável ferrítico AISI 409. Por meio do SHTPN obteve-se uma camada martensítica de nitrogênio na superfície do aço. Após o SHTPN as amostras foram temperadas de 950°C e revenidas nas temperaturas de 200, 400 e 600°C. A resistência à corrosão foi avaliada por meio da técnica de polarização cíclica e a dureza através de ensaios Vickers. Verificou-se que o SHTPN afetou significativamente a dureza do aço e o tratamento de têmpera refinou e melhorou a distribuição da martensita de nitrogênio. A camada martensítica formada apresentou espessura da ordem de 660 ?m. Os resultados indicam que é possível obter uma camada martensítica com dureza de 620 HV e aumento da região passiva, bem como do potencial de nucleação de pite quando comparado à condição não tratada (ferrítico). O melhor resultado de corrosão foi obtido para a amostra revenida na temperatura de 200°C.

Aug 8, 2018

By R. F. Mehl, B. Lustman

THE formation of intermediate phase layers in cementation processes has been subjected to extensive qualitative investigation though to relatively little quantitative study; this work has recently been fully summarized by F. N. Rhines.1 It is necessary here only to enumerate the general conclusions drawn concerning the kinetic laws governing the growth of intermediate layers and to state what is known concerning the structural changes accompanying the generation of phase layers. I. When the intermediate phase is protective in type-i.e., when its density is less than that of the base metal, so that a continuous coating is formed and maintained-the isothermal growth of the phase follows a simple parabolic equation: [1 = ki [I]] where X is the thickness of the alloy layer, k the reaction rate constant, and [t] the time. The applicability of this equation to diffusion processes is tested by plotting the square of the thickness versus time, or by plotting the thickness versus the square root of time; the resultant achievement of a straight line in such a plot has been considered sufficient proof of the validity of this equation. Exceptions have been found where liquid phases are involved in the reaction, where the diffusion layer is cracked,2 and where thin semimetallic oxide and sulphide coatings are formed on metals.3 In the first two cases the thickness increases linearly with time, and in the latter it is a logarithmic function of time. 2. The rate of thickening varies with temperature according to the Arrhenius equation: [k = Ae-QIRT [2]] where k is the parabolic rate constant of Eq. I, or some other rate-descriptive function, A is the action constant, e the base of natural logarithms, Q the heat of activation, R the gas constant, and T absolute temperature. This equation has been found to be generally valid except when transformations occur during reaction in either the base metal or in the reaction layer; in such instances Eq. 2 is still applicable with different values for the constants A and Q above and below the transformation temperature. 3. All phases that are stable at the temperature at which diffusion occurs will appear in the interdiffusion of two components. In some cases certain of the phases may be too thin to be observed and identified easily. Nonequilibrium phases have never been noted in thick reaction layers; i.e., layers of a thickness that may be discerned microscopically. The relative thickness of each phase in a diffusion layer is proportional to the concentration gradient and to the rate of diffusion in that phase.4 The reaction layers tend to have a

Jan 1, 1942

By J. P. Brady

A major spontaneous combustion incident occurred in the sealed goaf of the SL3 Panel; Southland Colliery in 2003 resulting in the loss of a longwall and sealing of the mine. The most important issue for the new owners, Yancoal Australia Pty. Ltd, was to effectively manage the atmosphere in the fire affected sealed area. This atmosphere comprised of flammable gases, the products of combustion and excessive levels of oxygen due to pressure differentials across the panel isolation seals with a potential ignition source associated with the residual spontaneous combustion event. The challenges were met in the first instance by the erection of pressure balance chambers with limited success. The problem was not solved until the pressure chambers were pressurized using a Floxal Nitrogen Plant supplied by Air Liquide Australia. Given the success of this approach on a small scale, a higher capacity Air Liquide Floxal Unit was acquired to manage spontaneous combustion at the recommencement of longwall mining operations. This provided the ability to pressurize pressure chambers that were installed in the Maingate Seals behind the face of the adjacent Longwall Block effectively preventing the ingress of oxygen and permitting the goaf to self inert in a reasonable time period. This paper summarizes a new proactive method of mitigating the risks associated with active and sealed goaves. Proactive management of these areas using low flow nitrogen into pressure chambers to maintain a positive pressure has eliminated typical reliance in explosion proof or explosion resistance seals as the primary control.

Jan 1, 2009

By R. H. Oitto

To determine whether reflectors could substitute for the trip lights referred to in the Federal Mine Safety Code, the Bureau of Mines studied trip safety devices under simulated haulageway conditions. The noticeability of reflectors compared with trip lights and fluorescent panels was evaluated from distances of up to 850 feet with light source intensities of up to 1-6 foot-candles (ft c). Reflectors tested consisted of a reflective lens in a holder secured to a frame that can be attached to a trip. Reflectors were found to be suitable for use as a trip safety device. In fact, for the conditions in many underground haulageways some reflectors would be more effective than a permissible trip light.

Jan 1, 1968