Search Documents

By Leticia Gabriela Winck

As escórias de aciaria, além de ser um coproduto da fabricação do aço, desempenham um papel importante na qualidade dos aços produzidos. Entender como elas se comportam durante o processo de refino é fundamental. Por exemplo, no refino secundário, a absorção de inclusões pela escória é umas das principais formas de se obter aços com maior limpeza inclusionária, e consequentemente, mais nobres. O presente trabalho tem como objetivo a caracterização de fases de escórias de refino secundário do sistema CMAS (CaO, MgO, Al2O3, SiO2), a fim de se obter informações a respeito de sua composição e fração líquida, além de prováveis fases sólidas. Para isso, quatro amostras de diferentes composições químicas foram fundidas em forno elétrico resistivo a altas temperaturas. As amostras também foram analisadas por diferentes técnicas como: microscopia eletrônica de varredura com sistema EDS acoplado (MEV/EDS), difração de raios X e simulação termodinâmica. Os resultados obtidos experimentalmente foram condizentes com as simulações termodinâmicas e com os resultados encontrados na literatura.

Aug 16, 2017

By J. M. Goris

Cable bolt supports are becoming an important ground control technique in underground mines in the United States and Canada. They show great versatility and are adaptable for use with many mining techniques, they have high load-carrying capacities, they can be installed in small areas with low roots, and they are cost effective. Investigators in a number of research institutes in North America have conducted studies to assess the material and support properties of cable bolts, evaluate their support capabilities under various mining conditions, and provide design criteria for using cable bolt supports as roof control systems under varying mining conditions. While conducting these studies, personnel have collected important information on the history, application, performance, and economics of these supports. This U.S. Bureau of Mines report documents this information so that ground control personnel unfamiliar with cable bolt supports can gain an understanding and appreciation of their use. A comprehensive bibliography of technical information on cable bolt supports was selected by the authors and is also presented.

Jan 1, 1994

Judicious placement of a range of geotechnical instruments was employed at the Tasmania gold mine, Beaconsfield, Tasmania, as a key strategy in the monitoring of rock mass conditions over the past four years. The range of instruments employed included vibrating wire stress-meters and hollow inclusion cells to monitor changing stress conditions, resistance wire and multipoint borehole extensometers to monitor the impact of stress changes on the integrity of the rock mass, and instrumented cable bolts and threadbar bolts to monitor the static and dynamic impact of rock mass changes on the installed ground control system. Initially the monitoring was of a qualitative nature, monitoring change from the time of installation. The value of the output was considerable when considered in relation to the ongoing seismic record which was also being monitored. It was clear from the seismic record and the monitoring results that stope blasting was the primary trigger for changing rock mass conditions. However, it was unclear how well observed behaviour was reflecting conditions anticipated by elastic numerical modelling. The latter had predicted significant stress increase in the near field of man-access footwall development. Qualitative monitoring and visual inspection did not support the modelling prediction, and this led to a program of quantitative measurement being undertaken. Measurement of the absolute stress condition in the backs of footwall development immediately adjacent to monitoring hollow inclusion cells provided the benchmark for tracking quantitative stress change. The program provided insight into the evolution of principal stress field magnitude and orientation in relation to rock mass change observed with extensometers and instrumented ground control elements, as well as providing a degree of calibration between the elastic numerical modelling and the virgin stress field. Calibrated monitoring data has also provided a useful benchmark for finite element modelling which is to be used for future mine-wide design.

Nov 25, 2010

By G. P. Marino

The "conductivity ", Kr, of a spherical void in a linear temperature gradient due to radiation is calculated by integration of the general expression for diffuse radiation between two gray surfaces of arbitrary orientation. The spherical geometry allows an exact evaluation of the phenomenon without resorting to up-proximate expressions for the radiant heat flux. The resulting expression for Kr is three quarters of the approximate value obtained by Loeb. IN the determination of the thermal conductivity of porous materials such as sintered UO2 and ThO2 fuel pellets, the magnitude of the thermal conductivity in the pores due to radiative heat transfer across the pore, Kr, may be important in assessing the total conductivity of the pellets. Loeb' has calculated Kr for various pore geometries by approximating the net flux of heat between two surfaces of temperature difference AT as 4eT~AT and obtained: K,=4yoet3odp [1] where a is the Stefan-Boltzmann constant, E is the emissivity of the radiating surface, To is the average absolute temperature of the region across which radiation occurs, dp is the largest dimension of the gap in the direction of heat flow, and y is a geometric factor. That is: y = 1 for laminar pores and cylindrical pores with axes parallel to the heat flow direction, y = 2/3 for spherical pores, y = /4 for cylindrical pores with axes perpendicular to heat flow direction. It was the purpose of this work to obtain an exact expression for K, in spherical pores by integration of the general expression for the net heat transfer between two incremental areas on the surface of a spherical pore. This procedure yields a value of Kr 3/4 of that obtained by Loeb. I) CALCULATION OF Kr Fig. 1 illustrates the general geometry which defines the problem. The total emissive power for a gray body is given by: E = EoT4 [2] where E is the radiated energy per unit area of the radiation surface per unit time, T is the absolute temperature, o is the Stefan-Boltzmann constant (o = 5.67 X lo- '' watt per sq cm-"K1), and E is the emissivity of the surface. Although Eq. [2] gives the exact expression for the total emissive power of any gray body, all practical problems involve the net exchange of thermal radiation between a body and surrounding bodies. The two major considerations in the solution of such problems are a) shape and relative position of the surfaces and b) the emissivities of the surfaces. In this work it shall be assumed that all incremental areas on a pore have the same emissivity and, further, that little or no reflection occurs (i.e., the radiation hitting a surface is either absorbed or transmitted). Thus, the solution of the stated problem requires only that consideration a be satisfied. Consider two incremental surface areas dA 1 and dA2 of the same material in a general orientation to one another. Let dAl be at temperature TI and dAz be at T2. Fig. 2 illustrates the geometrical parameters involved. That is, 71, is the normal of dA, n2 the normal of dA2, r the line connecting the centers of each area, 81 the angle between nl and r, and Q2 the angle between 7,2 and r. Using Eq. [2] and the Lambert cosine law of diffuse radiation it is easily shown that:293 WdAf- dA, = ecr T*------^fpi------" dAidA2 [ 3a 1 and

Jan 1, 1970

By A. MacG. Robertson

A cone penetrometer has been used to assess the level of stress existing in hydraulically placed mine backill. The test apparatus was fabricated at the mine and consisted of a steel cone, connector rods and a hydraulic jack. Testing was carried out from a manway passing through the centre of the stope. The cone was pushed horizontally into the fill, both at right angles and parallel to the orientation of the stope walls, and the resistance to penetration was measured. Corrections were made to allow for friction along the rods. In a cohesionless sand, such as mine fill, the point resistance should be directly related to the in situ stress. The stresses in mine backfill are due to o the self weight of the fill o convergence of the footwall and hangingwall of the stope. Silo theory was used to estimate that component of the in situ stress due to the self weight of the fill. The difference between the stress predicted by silo theory and the stress estimated from the cone resistance was assumed to be due to convergence of the stope walls.

Jan 1, 1986

By Z. Zak Fang, P. Fan, S. Middlemas

"Titanium dioxide (T1O2) has been widely used as pigment in paints, paper and cosmetic products, as well as high-tech applications such as PV Cells, semiconductors, biomedical devices and air purification. T1O2 pigment is primarily produced by the high temperature chloride process, resulting in considerable CO2 emissions. A novel hydrometallurgical process for making T1O2 pigment without direct CO2 emission is investigated. The new method promises to eliminate direct CO2 emissions, consume significantly less energy, and produce minimal environmental waste. The novel process involves molten salt roasting of titania slag, with subsequent washing, leaching, solution purification, hydrolysis, calcination and post-treatment stages, resulting in high-purity anatase or rutile pigments while realizing significantly reduced environmental impacts. Pigment whiteness is critically sensitive to trace amounts of discoloring impurities such as iron and chromium. Several methods for reducing the levels of these impurities are investigated. Energy consumption and emission models are also developed.IntroductionTitanium dioxide (T1O2) is one of the most commonly used minerals in the chemical manufacturing industry. It has been commercially processed since the early 1900's, and has a wide variety of applications. Pigment is used in paints [1], plastics and paper [2], sunscreen [3], cosmetics and even as a food additive [4]. T1O2 has also been used in photovoltaic cells [5], biomedical devices [6], and in air purification [7]. T1O2 pigment has a refractive index of 2.7, which imparts a high level of opacity (and hence whiteness) to whatever material it is added [8]."

Jan 1, 2012

The process of pile driving disturbs the soil around the pile. The nature and magnitude of disturbance depends upon 1) the pile size, and 2) the nature of soil. Therefore, the prediction of a single pile behavior based on soil properties of undisturbed soil samples may not match its performance. Under lateral loads, the pile may loose contact with the soil near the ground surface especially in clays. The soil pile interactions are influenced the most by pile behavior in this zone. This situation further affects the tally of prediction and performance. Piles are used in groups. The zones of overlapping stress from one pile to the other both around the pile and below their tip particularly in soft soils, contribute to group effects. Empirical solutions have been developed for prediction of the pile group behavior. The group action is more involved under vibrations. Several cases of single piles and pile groups under static and dynamic loads from published records have been analysed. It has been shown that single pile test is the best source of information on the soil-pile-soil interaction effects.

Jan 1, 1989

By J. Lux, B. Clermont

Magotteaux, with the co-operation of Anglo Platinum, has erected a fully instrumented pilot plant at Frank concentrator, which is being used to study the influence of a variety of grinding parameters. This paper will discuss only the influence of mill speed and pulp density on secondary stage grinding. A Ø0.82 x1 m open circuit mill was used with reclaimed Merensky tailings as feed. The conclusions apply to this pilot plant but further investigation needs to be done to verify whether the same trends will be applicable to a large industrial-scale mill.

Jan 1, 2004

By Ken-ichi Machida

"Surface modification of R-Fe-N intermetallic compounds was made to improve their magnetic property and nitrogenabsorbing ability, arid high-performance resin-bonded magnets and nitrogen storage materials were developed: Surface coating for Sm2Fe11Nx by the zinc metal produced via photodecomposition of Zn(C2Hs)2 was effective to avoid the further oxidation in the molding process of the fine powders for bonded magnets and the resulting (BH)max values were improved to -186 kJm-3. Meanwhile, R2Fe17 as the mother compounds for RzFe11Nx was highly active for decomposition of NH3 molecule and subsequent nitrogen absorption as metal nitrides. Furthermore, even inert Nz molecule was dissociated on them by impregnating Ru metal and the resulting nitrogen atoms were absorbed in the crystal lattice of R2Fe17. These results demonstrated that the nitrogen storage system was established by cycling the nitrogenation and hydrogenation of RzFe11/R2Fe11Nx materials.IntroductionProcessing for rare earth metals and intermetallic compounds requires well-controlled conditions in order to avoid the oxygen contamination involved in it due to their high reactivity, as causes the serious damage for materials such as magnets, metal hydride for hydrogen storage, and so on. Rare earth-iron intermetallic compounds, R2Fe17, provide the corresponding metal nitrides (R2Fe11Nx) by heating in N2 or a mixed gas stream ofNH3-H2 [l] and, among them, Sm2Fe11N3 has been particularly noted as one of the promising materials for high-performance permanent magnets such as bonded ones [2- 6]. Usually, the nitrogenation for Sm2Fe17 is made in Nz, but it needs the much more hard conditions of reaction pressure (-10 MPa), temperature (-550°C) and time (-72 h) than the nitrogenation in the NH3-H2 mixture [l]. In the latter case, a significant amount of nitrogen can be interstitial introduced in· the R2Fe17 crystal lattice (x=-7) under the more moderate conditions than in N2 (at 0.1 MPa and -450°C for -3 h) [3-6] and then, in a similar manner as metal hydride systems [7], the excess nitrogen in RzFe1 7Nx (x>3) is reversibly desorbed by heating at a temperature around 500°C in Ar to form the RzFe11N3 compounds. This behavior of nitrogen absorption and desorption has a close relation to the sites for nitrogen in the crystal lattices."

Jan 1, 2000

By Rudolph G. Wuerker

THE Krupp-Renn Process,[1] has been successfully used to treat low-grade iron ores, laterites, titaniferous sands, and other minerals, and before World War I1 25 units were built by the Krupp-Grusonwerk, Magdeburg, Germany. J. J. Howard[2] has shown theoretical advantages of the pyro-metallurgical treatment over conventional approaches; and the process was described by R. Durrer[3].

Jan 1, 1951

By Carlos Maurício F. Vieira, Lázaro A. Pizatto, Marcus Paulo Cardoso, Sergio Neves Monteiro, Joao Victor C. Nunes, Gustavo S. R. Matheus, Frederico M. Margem

The interest in composites with natural fibers is due, among other factors, to the growing worldwide concern with the preservation of environment and renewable raw materials. The natural fibers have many particular properties that make them an attractive alternative to traditional synthetic fibers. The advantages of using these fibers are: low cost, renewability, biodegradability, low toxicity, abundance and specific strength. The searching for new suitable, economically viable and technologically advanced materials justifies the accomplishment of this work that aims at comparing the mechanical behavior of polyester matrix composites with epoxy matrix composites reinforced with hemp fibers Izod impact tested. The specimens with dimensions: 10 63 12.7 mm, made in different volume fractions of fiber: 0–30 vol%. The samples were tested at PANTEC pendulum model XC-50 located at LAMAV/UENF. With this research was possible to analyse the mechanical properties of these two new materials.

Mar 1, 2018

By Jochen Petersen, Diane Taggart

"At an average of 90.3% (for the period of 1 January 2009 to 30 September 2011), Zincor’s zinc recovery was well below the industry standard of 96%. The losses through the residues, in particular the iron residue, were the biggest contributors to the overall zinc loss. It was believed that this loss could be decreased with the implementation of seed recycling. A plant trial was run to test the implementation of a seed recycle. The rate of seed addition through recycle was increased over a 4-week period. The presence of seed decreased the insoluble zinc loss by providing additional surface area for iron to precipitate onto, and reducing coating of unleached neutralising agent. The soluble zinc loss was also decreased at low and moderate seed recycle volumes. The improvement was attributed to agglomeration growth of the recycled particles, which improves the dewatering characteristics of the precipitate. In contrast, the soluble zinc loss increased at high seed recycle rates. This result was attributed to particle crowding and a low wash ratio.INTRODUCTION The Zincor refinery, which closed in December 2011, was situated just outside of Springs in the Gauteng Province of South Africa and employed the conventional Roast-Leach-Electrowin process, which accounts for 75 to 80% of the annual primary zinc production in the world. The refinery fed up to 220 000 t/a of zinc sulphide concentrate. The major portion of the raw material was sourced in Southern Africa from the Rosh Pinah and Black Mountain mines. Between 20 000 and 40 000 t/a of material was imported to make up the deficit and to improve the grade of the feed material. The iron contained in the zinc concentrates, at an average of 6.03% (for the period of 1 January 2009 to 30 September 2011), resulted in the formation of zinc ferrite during roasting, which is insoluble under atmospheric leach conditions. At Zincor, most of the zinc ferrite was dissolved in the residue treatment plant at elevated temperature and high acid strength. The leach liquor from this aggressive leach contained between 15 to 30 g/L of iron, mostly in the ferric form, and was known as the hot iron solution (HIS). The presence of iron in the liquor had an adverse effect on the zinc operation, particularly on the current efficiency in the electrowinning circuit. Therefore the iron needed complete removal."

Jan 1, 2016

By Jack Zhang, Chuck Edwards

"The versatility and specificity of rare earth elements (REEs) have led to their use in an ever increasing variety of applications in new technologies. Consequently, demand for REEs has increased significantly. However, to separate REEs safely and effectively is a complex and expensive process. While China has consistently invested in R&D of REE processing technologies, there have been only sporadic activities in REE mineral processing in North America in the past 20 years. This paper presents a review of REE mineral processing technology, providing an update on current capabilities in REE mineral processing. This paper reviews REE extraction from the major commercially valuable REE-bearing minerals such as bastnaesite, monazite, and xenotime, and also from the ion-absorption type of REE deposits. Currently, there are four major REE mining areas in China, one in the United Sates, and one in Australia. A review of the REE extraction processes in these major REE mining areas closes out the paper.INTRODUCTION The rare earth elements (REEs) include the 15 lanthanide elements, plus yttrium and scandium. The lanthanide elements are normally categorized in two groups: the light rare earth elements (LREEs), i.e. lanthanum through europium (atomic number (Z) = 57 through 63); and the heavy rare earth elements (HREEs), i.e. gadolinium through lutetium (Z = 64 through 71). Yttrium is usually grouped with the HREEs due to similarity in physical and chemical properties. Table 1 lists the REEs, atomic numbers, and abundances in earth’s crust (Taylor and McCleannan, 1985). Promethium is the rarest due to lack of stable isotopes. REEs with low atomic numbers are more abundant than those with high atomic numbers. More interesting is that the REEs with even atomic numbers are much more abundant than adjacent lanthanide elements with odd atomic numbers as shown in Table 1."

Jan 1, 2012

By Milca Ventura dos Santos, Ricardo Rodrigues Grizotti, Luciano Henrique Andrade de Resende, Francisco Ricardo Casa Neto, Paulo Roberto de Oliveira Junior, Bruno Rodrigues Ferreira

O trabalho tem por objetivo demonstrar o processo de desenvolvimento e implantação da automatização nas operações, atividades de almoxarifados (recebimento, armazenagem, movimentação, inventário, picking e entrega de materiais), com o uso da tecnologia SAP FIORI com interface nos sistemas operacionais Android e IOS para utilização do Mobile (smartphones e tablet’s), já alinhado ao momento da indústria 4.0, visando inovações tecnológicas nos campos de automação, controle e tecnologia da informação. O desenvolvimento nesta nova plataforma visa tornar as operações de almoxarifados mais ágeis e eficientes, buscando otimizar o processamento das informações com mais rapidez, redução do tempo de permanência das mercadorias nas áreas de transferência e gerar maior rastreabilidade dos processamentos com interface direta e on-line com o ERP-SAP da organização. A metodologia do trabalho foi identificar as oportunidades de explorar as melhores potencialidades das soluções do SAP Fiori, alinhadas aos sistemas operacionais Android e IOS para uso de celulares, tablet’s, com comunicação através da rede interna e/ou 3G/4G sempre visando otimizar todas as atividades operacionais (fluxo de materiais) e administrativas (fluxo de informações) dentro dos processos dos almoxarifados e suas áreas de interface. O projeto iniciou-se e sendo implementado nas unidades de Planos (ArcelorMittal Tubarão e Vega), e com plano de expansão para as unidades de Longos da ArcelorMital Brasil durante o ano de 2019. Nesta primeira etapa o resultado alcançado foi de plena adequação, tendo sido encontrado benefícios em redução de erros; aumento de segurança; redução de custos; otimização de processos; transparência em dados; customização de produtos, o qual espera-se que a curva de aprendizado naturalmente nos levará a adoção de novas soluções incrementais resultando nos melhores níveis de gestão do processo de armazenagem e movimentação de materiais.

Oct 1, 2019

By Conny Postupack

The first principle one usually learns about blasting is that competence in this field is best gained by experience in making blasts rather than by reading a book or by listening to a lecture. The reason for this is that there are a large number of variables affecting blasting results and not all of these can be accounted for by a few rules or a few sets of equations. Even an experienced in a new area, may have co make one or two himself to the new conditions with which he blaster when operating shots just to acclimate is faced.

Jan 1, 1991

By William Marsh Baldwin

TWO of the most useful and important equations available to the metallurgist for the study of plastic deformation of metals are the Huber-von Mises-Henckyl-~ and the St. Venant7-10 equations. Huber-von Mises-Hengky Equation The Huber-von Mises-Hencky equation answers the question: When does plastic flow occur in metal that is subjected to a multi-axial stress? It occurs, according to this equation, when the three principal stresses,t UI, u2, and u3 satisfy the equation: (<ri - <r2)2 + (<r2 - <rsY + (ff! - <r3)* = 2Ki [i] Here K is the yield strength of the material as determined in an ordinary tensile test. If the quantities ul, 52, andas are assigned to the coordinates of a Cartesian three-dimensional system, this expression describes a cylinder whose axis of symmetry is inclined at equal angles to the three coordinate axes4s6 (Fig. I). The radius of this cylinder is .\/%K. For the purpose of simplicity, it is sometimes advantageous to ascribe the values al/K = sl, az/K = s2, UD/K = SJ to the three coordinate axes instead of the principal stress alone. In this case, Eq. I becomes (*i - s*)1 + (s2 - S3)2 + (si - SiY = 2 [2] and the radius of the cylinder becomes \/%. In the latter method of representation, a point lying inside the cylinder indicates that the metal will react elasti-cally, whereas a point lying on the cylindrical surface indicates that the metal will behave plastically. Some of the geometric features of this cylinder are worthy of study. Let us inquire first as to what interpretation may be placed upon what we will choose to call the "circles of latitude" of the cylinder (L in Fig. I) and the "meridians" of the cylinder (M in Fig. I). Circles of Latitude Circles of latitude are formed by allowing a plane, passing perpendicular to the cylinder axis, to intersect with the cylinder. Any point, P, on this circle is presumed to have the coordinates sl, SZ, and s3. The coordinates of the point resulting from the intersection of the plane and the cylinder axis will be a, a, and a (since the cylinder axis is equally inclined to the three coordinate axes). L?t US now pass a line through the point on the circle and the point on the axis.

Jan 1, 1946

By William Marsh Baldwin

TWO of the most useful and important equations available to the metallurgist for the study of plastic deformation of metals are the Huber-von Mises-Henckyl-~ and the St. Venant7-10 equations. Huber-von Mises-Hengky Equation The Huber-von Mises-Hencky equation answers the question: When does plastic flow occur in metal that is subjected to a multi-axial stress? It occurs, according to this equation, when the three principal stresses,t UI, u2, and u3 satisfy the equation: (<ri - <r2)2 + (<r2 - <rsY + (ff! - <r3)* = 2Ki [i] Here K is the yield strength of the material as determined in an ordinary tensile test. If the quantities ul, 52, andas are assigned to the coordinates of a Cartesian three-dimensional system, this expression describes a cylinder whose axis of symmetry is inclined at equal angles to the three coordinate axes4s6 (Fig. I). The radius of this cylinder is .\/%K. For the purpose of simplicity, it is sometimes advantageous to ascribe the values al/K = sl, az/K = s2, UD/K = SJ to the three coordinate axes instead of the principal stress alone. In this case, Eq. I becomes (*i - s*)1 + (s2 - S3)2 + (si - SiY = 2 [2] and the radius of the cylinder becomes \/%. In the latter method of representation, a point lying inside the cylinder indicates that the metal will react elasti-cally, whereas a point lying on the cylindrical surface indicates that the metal will behave plastically. Some of the geometric features of this cylinder are worthy of study. Let us inquire first as to what interpretation may be placed upon what we will choose to call the "circles of latitude" of the cylinder (L in Fig. I) and the "meridians" of the cylinder (M in Fig. I). Circles of Latitude Circles of latitude are formed by allowing a plane, passing perpendicular to the cylinder axis, to intersect with the cylinder. Any point, P, on this circle is presumed to have the coordinates sl, SZ, and s3. The coordinates of the point resulting from the intersection of the plane and the cylinder axis will be a, a, and a (since the cylinder axis is equally inclined to the three coordinate axes). L?t US now pass a line through the point on the circle and the point on the axis.

Jan 1, 1946

By Haysler Apolinário Amoroso Lima, Francisco Pereira Netto, Vladnilson Peter de Souza Ramos, Bruno Nery Stoco, Gilvan Nascimento de Souza

Em um mercado dominado por tijolos de Al2O3-MgO-C, o revestimento de trabalho de panela de aço monolítico e CarbonFree se apresenta como uma tecnologia disruptiva para um novo patamar de qualidade do aço e eficiência energética. O presente estudo relata a motivação para a implementação do primeiro fundo de panela de aço com revestimento monolítico concretado in situ no Brasil, e apresenta uma análise preliminar dos resultados e vantagens observadas. Uma panela da Ternium Brasil foi revestida com refratários de Al2O3-MgO, e colocada em operação sem nenhuma necessidade de ajuste na operação da aciaria. A partir dos dados de processo e das medições a laser, calculou-se o desgaste do revestimento, bem como verificou-se a garantia de qualidade nos aços IF (interstitial free) e a maior preservação na temperatura do aço durante o refino secundário.

Oct 1, 2019

By Livia da Silva Mello

O objetivo deste trabalho é demonstrar que a utilização da Metodologia Six Sigma e ferramentas de controle estatístico e gestão, são eficazes para controle processo, redução custos e estabilização de processos em geral. O coque dentre os custos variáveis do Circuito Polimetálicos, representa o maior custo para a unidade de Juiz de Fora e a oportunidade em otimizar sua utilização, foi identificada a partir do levantamento de dados e benchmark realizado. Observou-se que a média do consumo específico de coque grosso + coque fino no Forno Waelz, em 2012 era em média 360 Kg/t de pó de aciaria (PAE) tratado estava muito superior a outras empresas que utilizam a mesma tecnologia para tratamento de resíduos. Definiu-se então como meta do projeto atingir 210Kg/t PAE até 2014. Passando por todas as etapas de um projeto Six Sigma: Definir, Medir, Analisar, Melhorar e Controlar, todas as ações realizadas garantiram uma melhor performance da variável: consumo específico de coque, uma média acumulada em 2013 de 212,3 Kg/t PAE e 181,5 Kg/t PAE em 2014 proporcionando um custo evitado de R$ 11,6MM para a unidade.

Sep 25, 2017

By Robert C. Weisner

Current production costs and market conditions in the potash industry of the Carlsbad area were studied to determine the potential values of the potash mineral resource that would be lost or foregone if the Waste Isolation Pilot Plant (WIPP) facility is constructed on the proposed site in that area. The purpose of the WIPP project is to investigate the possibility of developing a nuclear waste disposal plant in the salt formations at the site. Analyses were made of all potash deposits determined to be in the site. Mining and processing under the most favorable recovery systems were considered. Value determinations were based upon estimated operating and capital costs of current mine-mill operations in the Carlsbad area. This study was made for the Energy Research and Development Administration (ERDA) by members of the Federal Bureau of Mines Minerals Availability System staff.

Jan 1, 1979