Search Documents

By Ben E. Lindsly

The study of "bottom-hole samples follows in natural sequence the study of samples obtained under high pressures at the well heads of flowing wells. The principal object of this phase of gas-solubility research, started actively in January, 1930, was to gain a more accurate knowledge of the physical and chemical characteristics of the oil-gas mixtures that exist in natural reservoirs.. In possession of actual data regarding the condition of the oil; the quantity of gas liberated from solution upon dimunition of pressure; and the relative volumetric proportions of gas to oil at various pressures throughout the flow string in a well, it should be possible to predict, with a fair degree of accuracy, That physical changes these mixtures would undergo throughout the life of a pool. Such information not only is important in designing flow strings in flowing Tells but is important also in solving problems relating to pumping efficiency and the power required for pumping. Although certain fundamental data were obtained in the study of samples taken at the well head, "bottom-hole" samples are more representative of subsurface mixtures of oil and gas because they are obtained at reservoir temperatures, and before the oil has had the opportunity of intermingling with extraneous gas; that is, gas which either was not in solution originally, or which was liberated from solution at higher pressure, and later became mixed with the original undissolved gas.

Jan 1, 1933

By Alireza Javadi Nooshabadi, Kota Hanumantha Rao

Formation of hydrogen peroxide (H2O2), an oxidizing agent stronger than oxygen, by sulphide minerals during grinding was examined. It was found that pyrite (FeS2), chalcopyrite (CuFeS2), sphalerite ((Zn, Fe) S), and galena (PbS) generated H2O2 in pulp liquid during wet grinding and also when the freshly ground solids are placed in water immediately after dry grinding. Pyrite produced more H2O2 than other minerals and the order of H2O2 production by the minerals was found to be pyrite > chalcopyrite > sphalerite > galena. The pH of the water influenced the extent of hydrogen peroxide formation with greater amounts of H2O2 produced at highly acidic pH. Furthermore, the effect of mixed sulphide minerals, i.e., pyrite-chalcopyrite, pyrite-galena, chalcopyrite-galena and sphalerite-pyrite, sphalerite-chalcopyrite and sphalerite-galena on the formation of H2O2 showed increasing H2O2 formation with increasing pyrite fraction. There is clear correlation of the amount of H2O2 production with the rest potential of the sulphide minerals; the greater the rest potential of a mineral the greater the formation of H2O2. This study highlights the necessity of revisiting the electrochemical and/or galvanic interactions between sulphide minerals, and interaction mechanisms between pyrite and other sulphide minerals in terms of their flotation behavior in the context of inevitable H2O2 existence in the pulp liquid.

Jan 1, 2014

By L. A. Cornish

Pt-based alloys for high-temperature applications in aggressive environments have been under development for over 10 years, and are targeted to be used as either as bulk, or as coatings. The alloys comprise Pt, Al, Cr, and Ru, and the microstructure has been improved by composition to a best possible analogue of the nickel-based superalloys, which these alloys could partially replace. This was necessary because the previous best alloy had a strengthening precipitate volume proportion of only approximately 40 vol.%, whereas the nickel-based superalloys have around 70 per cent, and a lower volume would mean that the strength would not be the best that could be obtained. The microstructures were assessed using electron microscopy, and have been related to the alloys? hardness values. The current microstructures are much more like those of NBSAs, with a high proportion of the strengthening ~Pt3Al precipitates. Since the samples have to be small (platinum is expensive), hardness has been used as an indication of strength. Nano-indentation studies showed that the hardness and Young?s modulus were higher for ~Pt3Al than the (Pt) matrix. More extensive oxidation studies have been undertaken on the previous optimum sample, and the effect of cooling rate after heat treatment has also been ascertained. In addition, the samples were studied after different heat treatment times, and cross-sections were made in order to characterize the alumina scale that formed. The oxide scales of Pt-11Al-3Cr-2Ru (at.%) up to 100 h exposure did not spall, and were at least as good as those of the ternary alloys. There was no discernable Al depletion zone in the substrate, although it could have been at a greater depth than thickness of the samples studied. Further additions to the Pt-Al-Cr-Ru alloys have been studied, to increase the melting temperature as well as to reduce the platinum content without compromising the properties. Reduced platinum content would have the benefits of reduced density and cost. The target elements include vanadium and niobium, of which vanadium is of special interest, since it is a South African product. Before these additions could be made, phase equilibria studies were undertaken so that the maximum addition could be ascertained, and also to check any possible ternary phases, which could be deleterious. Work on the Pt-Al-V system revealed a ternary phase, ~V27Pt54Al19 (at.%), which has a eutectic reaction with (Pt). The maximum V addition is likely to be around 15 at.%, otherwise ~Pt3V or the ternary phase will form, and not the required (Pt)/~Pt3Al phases.

Jan 1, 2012

By J. Fletcher Smoak

The value of abrasive materials consumed in the United States increased 37% in value over that of 1983 to $439 million; of which, 58% was manufactured abrasives, 36% was industrial diamond (natural and synthetic), and 6% was natural abrasives. Production value of natural abrasives, which consist of crude tripoli, special silica stone, garnet, and emery, increased 4% Production of crude tripoli, a finely disintegrated chert, increased 12% in quantity and 8% in value. Shipments of processed tripoli increased only 3% in quantity but increased 16% in value, with large increases occurring in both major end-use categories. Production of garnet, an abundant iron-aluminum silicate, decreased slightly in quantity and value after posting continued increases in quantity and value since 1980. There was a significant decrease in the quantity and [ ]

Jan 1, 1985

By K. -I. Higuchi, M. Mizutani, K. Haga, A. Shibayama, A. Batnasan

In recent years, the quality of iron ores has decreased due to the increase in the content of impurities, namely quartz, aluminum, phosphorus, and sulfur. It indicates that the removal of impurities from iron ore is an extremely challenging task. In particular, the high amount of phosphorus in iron ore could be a problem for energy consumption and CO2 emission in the steelmaking process. To reduce the impact of phosphorus, mainly two approaches: the utilisation of low-phosphorus iron ore, or dephosphorisation of high-phosphorus iron ore using mineral processing technology, have been suggested. In this paper, the removal of phosphorus from a low-grade high-phosphorus iron ore containing 0.1 mass% P and 57.5% Fe by alkaline roasting and wet grinding is discussed. The iron ore consists mainly of hematite, goethite, and quartz. Effects of sodium hydroxide concentration used as an alkaline source, roasting temperature, grinding time, and particle size on the dephosphorisation of highphosphorus iron ore were investigated. The dephosphorisation efficiency, iron loss, and mineralogical components of low-grade high-phosphorus iron ore under various experimental conditions were characterised by using XRD, SEM-EDS, and particle size distribution analysis. Results showed that the phosphorus content was lowered from 0.1 mass% to 0.034 mass%, while the iron grade reached 59.8 mass% from 57.5 mass% by alkaline roasting with 0.05 w/w NaOH at 300 °C for 2 h, followed by wet grinding in an attritor with water for 30 seconds at room temperature. Under the experimental conditions, the dephosphorisation rate was about 54.7%, and the solution obtained by wet grinding contained 22.7 mg/L of phosphorus and 21.5 mg/L of iron. The recovery rate of iron by this process reached 99.9%. Keywords: Iron ore, phosphorus, dephosphoriszation, alkaline roasting, wet grinding

Jan 1, 2020

By Yogeshwar Sahai

Submerged gas injection into melts contained in furnaces, ladles, or similar transfer vessels is commonly used in industrial practice. In this review paper, conditions leading to gas bubble formation at the nozzle are first summarized. The increasing gas injection rates and other conditions, such as nozzle size, lead to regimes which are commonly known as "bubbling" and "jetting". These are explained. The gas/melt interactions result in energy transfer to the melt. In recent years, a large number of researchers have investigated the relationships between the energy density and the mixing times. Their work is reviewed, and the mixing mechanisms is described. Finally, computational approaches of modeling submerged gas injection are briefly presented.

Jan 1, 1993

By George Langford

Introduction The manufacture of ductile beryllium is one of the most interesting problems confronting the metallurgist today, and one which becomes more acutely in need of resolution as the uses for beryllium increase. Beryllium belongs to the hexagonal group of metals along with zinc, magnesium, and cadmium. The melting point of the metal is about l,280°C. ± 5°C. Due to its brittleness, the metal's chief use is as an alloying agent in copper and iron. The very low absorption coefficient of beryllium for x-rays makes the metal ideal for x-ray windows, and, similarly, because of its low capture cross-section for neutrons, the metal holds a preferred position in the field of nuclear physics. Modern x-ray diffraction methods were responsible for explaining the mechanism whereby zinc metal, although brittle when cast, could be made ductile at room temperature. The diffraction patterns of zinc and magnesium indicated the importance of the parts played by recrystallization and preferred orientation in this mechanism. It was with this in mind that an Investigation into the recrystallization and preferred orientation of beryllium was undertaken. The investigation, after a series of experiments were conducted involving cold-working and annealing, yielded the recrystallization temperature curve for beryllium. Both the texture of preferred orientation and the effect of recrystallization on this texture when subjected to compressive stresses were also determined. W. A. Alexander, J. K. Swinton and L. M. Pidgeon, in their investigation on The Recrystallization Temperature of Beryllium (C.I.M., Trans., Vol. L, 1947, pp. 657-664), utilized the Brinell ball as a means of cold straining the metal. Sufficient strain was developed to estimate the recrystallization curve for the metal. However, in order to determine the lowest recrystallization curve, as well as to develop a preferred orientation structure, larger deformation than that possible with a Brinell ball was required. The plastic deformation of beryllium can be carried out at an elevated temperature above 700°C. Above 850°C., the metal is quite ductile and can be readily compressed or extruded.

Jan 1, 1948

By B. S. Tani, R. V. Schablaske, M. G. Chasanov

In the Ti-Cd system two intermediate phases, TiCd and Ti Cd, have been found and characterized by X-ray diffraction powder techniques. An earlier reference' had reported the existence of the compound Tisd. No structural details, however, were given nor was there any indication of the possible existence of other binary compounds. Studies of the solubility of titanium in liquid cadmium2 led to the discovery of both TiCd and Tisd. The solid phase in equilibrium with saturated solutions of titanium in liquid cadmium at temperatures below 620°C is TiCd, whereas TizCd is the equilibrium solid phase above 620°C. Both thermal analysis and X-ray studies show that a peritectic reaction between the y phase (~isd) and cadmium to form the 6 phase (Ti Cd) occurs at 620°C. X-ray diffraction powder photographs of material isolated from the ingots used in the solubility measurements as well as material prepared by a direct heat of the appropriate stoichiometric amounts of titanium and cadmium can be indexed on the basis of a tetragonal unit cell with a = 2.904 ± 0.002A, co = 8.954 * 0.004A, c/a = 3.083. No variation of lattice parameters indicative of a range of composition is evident. With four atoms in the unit cell the calculated density of the intermetallic is 7.05 g per cm3; the observed value is 7.07 g per cm3. The TiCd lattice is primitive as indicated by the fact that there are no systematic absences among hkl reflections. The absence of all hko reflections for which h + k = 2n + 1 is also evident. This systematic absence indicates the following two space groups, C\h — P4/n and D&~4/nmm; both groups, however, have the same two- and four-fold positions. Stoichiometry, symmetry and space group indicate two likely structure types. They are the PbO-litharge3 (B10) type and the Ti CU (B11) type. Spatial considerations favor the B11 structure with atoms placed in the following positions: 2Ti (c) 0, 1/2, Z; l/2, 0, Z 2Cd(c) 0, 1/2, Z; 1/2, 0, Z The TiCd structure may be summarily described as a layered structure in which double cadmium layers alternate with double titanium layers along the c-axis. The best agreement between calculated and observed intensities is obtained for the values ZTi = 0.608 and ZCd = 0.130. Calculated and observed powder intensities as well as other pertinent powder data are recorded in Table I. Interatomic distances for the proposed structure are recorded in Table II and are to be compared with the distances of closest approach for titanium and cad-

Jan 1, 1962

By R. O. Burt

"IntroductionThe introduction to this section on gravity concentration indicated the wide range of equipment types that exist for the concentration of minerals, in what is the broadest size range of any concentration process.The equipment described in this chapter includes jigs, tables and sHme plant equipment. In contrast to the equipment described in the two succeeding chapters, this range of equipment, in nearly every instance, superimposes a mechanical movement on the fluid motion to effect separation of the valuable mineral from the waste mineral. The motion may be vertical Gigs), reversing (tables), or rotary (slime plants): however, in common they ""dilate"" the bed of particles to allow preferential settlement of the heavier particles.Description of Process UnitsJiggingJigging is the sorting of different minerals by stratification, based on the movement of a bed of particles relative to a fluid in a vertical plane.The basic construction of a jig is shown in Figure 1. Essentially it consists of an open tank filled with a fluid, normally water, with a horizontal jig screen at the top and with a spigot in the ""hutch"", or bottom compartment, for removal of heavies. The jig beri consists of a layer of coarse heavy particles (ragging) on the jig screen. This ragging is of a specific gravity between that of the minerals it is intended to separate.In operation the bed is made fluid by a pulsating current of fluid to provide stratification. On the upward or pulsion stroke the bed of ragging and slurry is normally Hfted as a mass, then as velocity of the upcurrent decreases it dilates, loosening the whole mass. On the downward or suction stroke it closes slowly again. The ideal is to control this dilation of the bed of material so that the heavier and smaller particles penetrate the interstices of the bed, while the larger heavies fall under a condition akin to ""hindered"" settling."

Jan 1, 1989

By D. M. Doyle

"In this paper I will summarized the Falconbridge Nickel Mines1) energy costs and consumption data by fuel, process, cost centre and estimate our future costs and consumption patterns 2) detail the distribution of electrical energy 3) distribution of other forms of energy 4) describe present and planned energy conservation schemes; and 5) discuss economic justification and responsibility.There is sufficient material in this presentation to warrant several technical papers, however we felt that an overview of all our data and endeavors on the subject, would be most beneficial to those companies formulating energy conservation plans. The data briefly referred to in this slide presentation can be found in the technical paper.Over a five year period, total energy costs will vary between $63 and $94 MM depending on the future rate of energy cost escalation. An unrealistic 32% reduction in energy consumption is required to hold our own in the years ahead whereas an attainable 10°;, reduction in energy consumption would save $9 MM over this five year period.Total energy consumption, tonnage of ore delivered to plants and their ration BTU’s per ton of ore, are graphed for the years 1973 through 1976 and forecasted for the 1980’s. In 1974 we along with other member companies of the Mining Association, determined our purchased energy per ton consumption rate and set, as our goal, a 20% reduction by 1980. The dotted lines calculated from the energy audit, based on 1976 data shows there is a potential for a 10% increase in energy per ton. This could result from a lower than forecasted mining rate and operation of the new roasting, electric furnace and acid recovery facilities installed for environmental considerations at designed capacity."

Jan 1, 1978

By Humphrey Dean

"Canadian mining companies now operate numerous Koepe-type friction hoists in a variety of different shafts, most of which have a depth in excess of 3,000 feet. Rope performance reliability is an absolutely essential ingredient of most installations and, for this to be provided, a more comprehensive understanding of rope reactions to applied stresses is required.It is the intent of this paper to illustrate for the operators the importance of the critical stresses encountered and to provide a maintenance program designed to circumvent potential difficulties."

Jan 1, 1970

This brief introduction tries to introduce delegates to this conference to the almost unbelievable attributes possessed by many microbes which might be relevant to geomicrobiology, and how most of these remain unexploited by us. It introduces some of the terminology which will be used and tries to suggest that there are rewarding times for those who set out to discover the natural biodiversity of bacteria in nature. Although we have exploited microbes, usually unwittingly, and suffered at their hands for millennia, it is only recently that we have begun to become aware of how they dominate our planet (most of the earthÆs biomass is bacterial) and are responsible consequently for most of what happens here. A few can cause us harm and occasionally kill us, but most bacteria are beneficial, impacting positively for example on how we grow our food and in cleaning up the pollution we create. They are simply indispensable to how we live. They have been responsible for many of the geochemical changes which have taken place on this planet and play major roles in the transformation of elements so essential to our existence (Newman and Banfield, 2002). No one should dismiss them as minor players in our game of life.

Jan 1, 2004

By Kunio Hashimoto

The conventional troughed belt conveyor system is the most widely used form of equipment for transporting bulk materials in the world today. The reason is not only because it is possible to transport a great deal over a long distance when compare to other types of equipment but also due to its greater economic efficiency and low initial and running costs. When dry, powdery materials and liquid materials are being conveyed, there are enclosed transport methods such as flow, case, air-slider and pipe line. In addition to features of the belt conveyor, a system employing a pipe line to transport dry powdery and liquid materials has always been considered an ideal method. This has been brought into reality through the Pipe Conveyor Sys tem.

Jan 1, 1984

By Takaji Kusakawa

In Japan, almost no natural gypsum is mined for industrial uses of gypsum, and almost all gypsum is synthetic gypsum, that is desulphogypsum, produced by waste sulphur dioxide gas from metal smelters and power plants, and other industrial waste sources. The amount of such sythetic gypsum production has reached more than six million metric tons per year (1979). Major uses are for cements and building materials. Other uses are soil conditioner, investment casting mold, organic composite materials, etc and sulphur recovery by gypsum decomposition is being examined. This paper summarizes present Japanese production and uses of sythetic gypsun produced from industrial waste.

Jan 1, 1982

By John Bley

White Pine Copper Company operates a mine in the Upper Peninsula of Michigan using a modified room-and-pillar system for extracting ore.1 Mine production averages 15, 500 tons per day. The terrain is predominantly level and the depth of cover varies from 500 to 800 feet over the present workings with depth increasing as mining progresses down the dip. The deposit is situated on a low angle plunging, anticlinal structure composed of sedimentary beds. Local terminology for the stratigraphic units which contain the ore horizons, named in ascending order, is as follows: lower sandstone, parting shale, upper sandstone and upper shale. The ore zones of copper enrichment are, contained in the parting and upper shales. The parting shale will vary; from 6. 5 to 9.0 feet thick; the upper sandstone from 2 to 10 feet; and the upper shale from 1. 5 to 6. 5 feet. Two variation of the room-and-pillar system are used to extract the ore depending on grade and local ground conditions. One system is called the parting shale method and recovers the parting shale only. This system requires a mining height of 8 1/2 feet to accommodate large-scale, high-capacity equipment and this working height is obtained by removing approximately 1 to 2 feet of the barren lower sandstone with the ore. Under the second system, locally termed full column, the mining height is about 14-1/2 feet and this system removes the parting shale, the upper sandstone and the lower mineralized zone, approximately 1-1/2 feet, of the upper shale at which point it is possible to maintain a competent back (Fig. 1).1

Jan 1, 1964

By Alvin W. Schillinger

Drilling was not entirely satisfactory in the search for native copper in the Osceola amygdaloid footwall as mining showed oreshoots to be more continuous than drilling indicated. The Geophysics Department of Michigan Technological University developed a portable induced polarization drill hole probe with a 3 electrode configuration and a sampling radius of 5'± A 20 ma current of alternately reversed polarity is pulsed at 3.5 sec. intervals and readings are taken every two feet. Potential is read during the "on" cycle for resistivity determinations. During the "off" cycle, after 10 ms delay, the I.P. potential is sampled for 10 ms and recorded. Resistivity (ohm-feet) and "S" values (mv/v) are plotted on semi-log paper. A lithologic log is plotted based on resistivity and anomalous "S" values noted. The low resistivity amygdaloid contains sills of high resistivity basaltic trap. Verified by core logs, amygdaloid-trap contacts could be picked to ±.5' from resistivity alone. Lithologic logs of long steel holes, based' on resistivity, now replaced sludge logging. An "S" value of 30 mv/v was established as the lower limit of diagnostic I.P. effects in mineralized amygdaloid and 50 mv/v as a threshold value for ore. Of 914 footwall zones drilled, 315 were probed yielding 203 anomalies. Success increased from 34% for drilling to 72% for drilling and probing. As checked by mining, 46 probe results were 78% correct. Failures were due to the instrument not detecting copper or to the misinterpretation of an anomaly. No false anomalies were found.

Jan 1, 1964

By N. S. Dalal, X. Shi, V. Vallyathan

"Correlated spectroscopic and cytotoxicity measurements were made on newly crushed silica to find whether the fracture-induced, silicon related (Si-0· or Si· type) free radicals play a direct role in the mechanism of hemolysis by silica particles. The free radical content of the silica particles was controlled through the radical decay, thermal annealing, and boiling processes, and was followed with electron spin resonance spectroscopy. Portions of the same sample were evaluated for their hemolytic potential, employing sheep erthyrocyte and optical absorption techniques. The results indicate little, if any, correlation between the amount of the silicon-based radicals and the hemolytic potential of the fresh dusts, but these or related radical sites might be contributors to silica cytoxicity and fibrogenicity via peroxidative pathways .INTRODUCTIONIn an earlier convnunication (1.) from our laboratory it was reported that mechanical crushing of coal and quartz under normal air atmosphere generates free rad;cals on the particle surfaces, and that these radicals decay with time, hence pointing to a higher toxicity of fresh dusts in relationship to pneumoconiosis and silicosis. More recently Fubin; et al.(2) have also reported the detection by electron spin resonance (ESR) of the formation of SiO· and Si·-type of radicals from quartz particles crushed under atmospheric conditions. In agreement with earlier ESR studies on single crystals of quartz crushed under high vacuum (10-10 torr) (3) and subsequent exposure to air (3), and to other gases (4), these radicals were identified (2) as being formed by the hemolytic cleavage of the Si-0-Si bonds and the reactions of the Si· and SiO· ,radical with atmosphere. Fubin; et al. (2) also suggested that these radicals might be involved in the mechanism of the fibrotic action by silica, either by transforming the particle surface into a selective oxidating agent or as an initiator of a sequence of reactions leading to fibrosis. Earlier Gabor and Anea (5) had reported that lipid peroxidation caused by free radicals on the silica surface might be involved in the red blood cell membrane damage. Thus far, however, no parallel cytotoxicity, fibrogenicity, and free radical studies on a given Quartz dust sample have been reported, except for some earlier work from our laboratory (1,6,7). We now present more recent results obtained from parallel cytotoxicity, fibrogenicity, and free radical measurements on a freshly made quartz dust. The dust’s free radical content was measured using ESR spectroscopy while its cytotoxicity poteni1al was estimated via hemolysis. Hemolysis was employed as the tox1c1ty test because it 1s a widely used method for estimating the potential of a dust for disrupting the cell membrane (8). The f1brotic potential was followed.by measuring the dust-induced lipid perox1dat1on. us1ng linole1c ac1d as a model lipid. As discussed below, the results obtained suggest new clues.to the mechanism of the Quartz-related cytotoxicity and fibrogenicity."

Jan 1, 1988

By C. Lupi

The electrorefining of primary copper is a well known technology: in this work copper scrap was directly processed in the same way. he copper and copper alloy scrap was previously pressed by means of a 20 tons apparatus in order to avoid pyrometallurgical operations. The samples obtained in this manner showed a good compactness so that they were used as anodes in the electrorefining tests. The tests were carried out on anodes made by copper scrap, copper alloy scrap and a mixture of the two. The electrorefining tests were performed at both 303 and 333 K, in a perspex cell having a volume of 500 ml using a current density of 250 A/m2. The cathode used was always a sheet of pure copper and the electrolyte composition was 40-50 g/l Cu as CuS04 and 150-200 g/l H2SO4. Current efficiency in the range of 92-97% and specific energy consumption ranging from 0.14- 0.20 kWg of copper were reached in all the tests. The refined copper deposits were analyzed by AAS to verify their purity and observed by SEM to highlight their morphology.

Jan 1, 1998

By Konstantinos Modis

According to recently established theoretical analysis and under certain conditions, a critical sampling density can be determined for an earth-related space-distributed natural variable. Sampling above this critical limit adds little to the mapping results. The objective of this paper is the application of the above theory to the Sesklo clay quarry in Greece, where Heracles General Cement Company had conducted a sampling campaign to estimate its reserves. The structural analysis of Al2O3 values generated a variogram model, from which the critical sampling density was identified. This critical number was by far lower than the existing sampling density. Clay reserves were then estimated using geostatistics and inverse distance squares in different data schemes with variable densities. The results of the comparisons between the various models revealed that, when the sampling density was greater than its critical value, geostatistics and deterministic interpolation gave similar estimations, which is also in agreement to the theory. The optimal sampling grid finally proposed here, will result to significant cost savings in the next drilling program which is now in plan by the company.

Oct 1, 2009

By Troy Holm, Matthew L. Fuller, Frederick H. Earnest

Virtual Reality Animation Of The Proposed El Dorado Mine In El Salvador Assists Regulators In Reviewing An EIA

Jan 1, 2005