Search Documents

By S. Badr, R. Mendoza, M. U. Ozbay, M. D. G. Salamon

ABSTRACT: The use of coal pillars at depth is fraught with problems due roof control difficulties and the possible occurrence of coal or pillar bumps. In the USA the largest and most important application of pillars at depth is in longwalling, where chain pillars are the customary supports of the multiple entry developments. At first, the chain pillars were designed using conventional approaches, where the principle is that the strength of the pillar should exceed the load imposed on it. Such approach to design led to larger and larger pillars at great depths, but instead of eliminating, it tended to aggravate the roof control problems. Eventually the idea was born that small sized yielding pillars, which have proved to be successful elsewhere, might provide the answer to this pressing problem as well. The aim of this paper is to study the modes of pillar failure at great depths, using two solution methods. The first of these comprises some elementary solutions obtained with the aid of a simplified conceptualization of the rock mass. This model consists of a strain-softening coal seam sandwiched between two stratified masses. The second approach utilizes FLAC3D, which is a commercially available three-dimensional numerical modeling software package. To gain a better insight, both the strain-softening and ideally plastic Mohr-Coulomb constitutive laws embodied in FLAC3D were exploited. As expected, the width to height ratio of the pillar has proved to be the primary factor that determined the behavior of the pillars. Narrow pillars fail in a stable manner without the occurrence of instabilities. Intermediate w/h ratio pillars under the appropriate loading conditions, may fail suddenly and may even collapse totally. Squat pillars do show the potential for sudden, coal bump like side failure, but because the remaining large width of the inner core, the ruble around the pillar provides sufficient confinement so as to reestablish stability. Finally, the study revealed that the traditional Mohr-Coulomb law does not provide a useful insight into the failure of coal pillars. RESUME: L’utilisation des piliers de charbon dans les mines souterraines de grande profondeur occasionne des problèmes due aux difficultés de control de plafond et possibles fracture ou explosions au niveau des piliers. Aux Etats-Unies d’Amérique, l’utilisation des piliers dans les mines souterraines de charbon comme moyen de support est considèrees comme étant la plus grande et la plus importantes des méthodes utilisée dans le ‘’ longwalling method’’ ou une série des piliers sont disposé de manière à supporter les multiple entrées d’exploitation de charbon. En premier lieu, cette série des piliers étaient construit de manière conventionnelle avec un principe basé sur le fait que le poids exerce sur les piliers doit être inférieur a la force que ces piliers exerce sur le plafond. Ce principe a conduit a ce que le volume des piliers augmente au fur et à mesure que la profondeur au de la mine augmente. Malheureusement, au lieu de résoudre le problème de support, ce principe n’a fait qu’aggraver le problème de contrôle de plafond. Eventuellement une idée s’est dégagé allant du fait que les piliers endommagés de taille moyenne qui se sont avérés être efficaces ailleurs, pourraient fournir un indice à ce particulier problème. Le but de cette recherche est celui d’étudier les différent types de ruptures qu’un pilier peut occasionner lorsqu’il est utilisé a grande profondeur, tout en utilisant deux possible méthodes. La première d’entre elle comprend quelques solutions élémentaires obtenues avec l’aide d’une méthode simplifié et conceptuelle de la masse de la roche. Ce modèle consiste à prendre en sandwich la bande de minerais de charbon entre deux masses stratigraphiques sans pour autant endommager le plafond. La seconde méthode nécessite l’utilisation du ‘’ FLAC3D’’, qui est un logiciel commercialisé disposant d’un modèle numérique en 3 dimensions. Dans le but d’obtenir

Jan 1, 2003

By William Rodrigues Soares

Este trabalho apresenta uma avaliação da temperabilidade, microestrutura e tenacidade de dois tubos de aços (A e B) especificados pela norma API 5CT. O aço B tem um teor de elementos de liga maior que o aço A. As amostras foram temperadas em água a 29ºC e revenidas a 700ºC/15min. Avaliou-se a temperabilidade dos aços por meio do ensaio Jominy e a tenacidade por meio da energia absorvida no ensaio de impacto Charpy. As propriedades mecânicas foram medidas pelo ensaio de tração. A caracterização da microestrutura foi realizada de forma qualitativa por meio de microscopia óptica e eletrônica de varredura. O aço B com maior teor de carbono e de elementos de liga tem maior temperabilidade do que aço A. Os aços A e B apresentam uma microestrutura constituída de martensita revenida e pequena quantidade de bainita. As amostras do aço B apresentam maior energia absorvida, maior limite de resistência e menor ductilidade que o aço A. A presença de Mo em maior quantidade no aço B faz com que sua tenacidade seja superior ao aço A.

Aug 16, 2017

By C. Sima, M. Legoabe

Keywords: Pyrometallurgy, furnace, platinum Mortimer Smelter is one of the three smelting operations in the Anglo Platinum Group. It is located in the Limpopo Province, approximately 100 km north of Rustenburg, and approximately 15 km west of Northam. The smelter operation is the smallest of the three smelting operations in the group, with a smelting capacity of 170 kt/annum. The operation consists of a Larox filtration plant, a Drytech flash drying plant, a modified Elkem / Hatch 19.5 MVA furnace, and a 60 t/h matte crushing plant. The operation does not convert its furnace matte, and hence the final sulphide rich matte is transported to and processed further at the Anglo Platinum Converting Process (ACP) within the Waterval Smelter Complex in Rustenburg. Furnace slag is granulated, and processed through a slag mill, or transported to a slag dump.

Jan 1, 2006

By R. J. Fruehan

The oxygen activity and concentration were measured in Fe-Cr-0 melts in equilibrium with an oxide phase at 1600°C (2912°F). The activity was determined by ,use of the following solid oxide -electrolyte galvanic cell CY-Cr8,(s) I ZrOz(CaO) I Fe-CY-G(saturated)(l) The oxygen concentration decreases with increasing Cr concentration to about 270 ppm 0 at about 7pct CY and then increases gradually. The activity coefficient of oxygen (fo) decreases with increasing Cr. In melts containing up to about 20 pct Cr, log f is approximately a linear function of wt pct Cr with a slope (e q 2) of —0.037. The activity of chromium was calculated and found to exhibit a small negative deviation from Raoult's law. From the activity and solubility data for low chromium melts, the free energy of formation of chromite, FeCr204, was found to be -79.8kcal per mole where pure liquid chromium and oxygen at I wt pct in Fe are the standard states. ThE effect of chromium on the chemical behavior of dissolved oxygen in liquid iron is of great importance in controlling the deoxidation of steels containing a significant amount of chromium. Chen and chipman' equilibrated Fe-Cr melts in the presence and absence of slag with hydrogen-water vapor mixtures. They concluded that at 1595°C chromite was the oxide phase in equilibrium with Fe-Cr alloys containing less than 5.5 pct Cr while at higher chromium concentration Cr,O, was the stable phase. In the composition range 0 to 10 pct Cr they found that the interaction coefficient, was equal to -0.041. Turk-dogan,' Schenck and Steinmetz,, and pargeter4 measured egr) in a similar manner and found the value to be -0.064,-0.04, and -0.052, respectively. McLean and Be11 evaluated egr) from their data on the equilibrium of Fe-Cr-Al-0 alloys with H2/H20 mixtures and found it to be -0.058. However, McLean and Bell's value should only be considered an estimate because the effect of aluminum on the activity coefficient of oxygen is about a hundred times greater than that of chromium. Consequently, an error in the value of egl) used, which at the present time is not well-known, or an error in aluminum analysis, which is present in very small quantities, will result in a significant error in egr). Fischer et a1.6 determined the interaction coefficient (eEr) in Fe-Cr-0 melts not in equilibrium with an oxide phase and containing less than 18 wt pct Cr at 1600°C electrochemically. They determined a value of -0.031 for egr). Hilty et aL7 measured the oxygen content of Fe-Cr melts in equilibrium with an oxide phase containing up to 50 pct Cr. They found that the solubility of oxygen decreased as the chromium content increased to about 6 pct Cr and then increased gradually. They concluded that the equilibrium oxide phase was chromite below 3 pct Cr, distorted spinel from 3 to 9 pct Cr, and Cr,04 above 9 pct Cr. Adachi and lwamotoa also investigated this system, but did not find Cr30,. They X-rayed the equilibrium oxide phases and did not find the presence of Cr,O,. They also X-rayed the oxide phase extracted from a 65 pct Cr melt which was heat treated and did not find metallic chromium as would be expected if Cr3O4 were the equilibrium oxide phase as indicated by the reaction : 3Cr3O4 — 4Cr2O:, + Cr [lj It was the purpose of the present investigation to determine the effect of chromium on the activity coefficient of oxygen in Fe-Cr melts by measuring the activity and solubility of oxygen equilibrated with an oxide phase in the composition range 0.18 to 50.5 wt pct Cr at 1600°C (2912°F). The activity of oxygen in the melts was determined by use of the following galvanic cell: The relationship between the partial pressure of oxygen in equilibrium with the melt and the reversible electromotive force of the cell (E) is where 11 = 4, F is the Faraday constant, pb, is the oxygen pressure in equilibrium with the meit and is the oxygen pressure in equilibrium with Cr203 as determined from the free energy data compiled by Elliott et al? The oxide phase in equilibrium with pure chromium was assumed to be Cr If Cr30, were the equilibrium phase the activities derived would be approximately the same, since the best estimated free energy of formation of Cr,O,, if it does exist, is approximately % the free energy of formation of The activity of chromium in Fe-Cr alloys at 1600° C was also determined from the measured electromotive force. The activity of chromium (aCr) is related to the electromotive force as follows: , The oxide phase in equilibrium with pure chromium and Fe-Cr melts from 10 to 52 pct is assumed to be Cr203 so that n equals three. If future work proves the existence of Crs04 in equilibrium with Fe-Cr melts and pure chromium, the experimental results can be reevaluated using a value of $ for n in Eq. 141. A value of ^ for n will make the activities about 10 pct higher. In order for Eqs. 131 and [4J to be valid the electrolyte, ZrOa(CaO), must exhibit predominantly ionic conduction at the temperature and oxygen partial pressure of its use. Previous work1' has demonstrated that ZrOz(Ca0) is predonlinantly an ionic conductor

Jan 1, 1970

By Nilo Nogueira da Silva

O objetivo deste trabalho foi investigar os efeitos da temperatura de laminação na microestrutura de um aço microligado ao Nióbio através de simulação por ensaios de torção a quente. Ensaios foram realizados com deformações em resfriamento contínuo para determinar as temperaturas de não recristalização da austenita (Tnr) e de início da transformação austenita-ferrita (Ar3). Foram realizados ensaios de torção simulando diferentes esquemas de laminação a quente em laminador Steckel, variando-se as temperaturas dos passes de acabamento. Foi observado, nas curvas tensão em função da deformação dos ensaios de torção, gradual encruamento da austenita quando a temperatura da última deformação foi inferior à 870°C. Foi também observado que o tamanho de grão ferrítico cresce com temperatura de laminação de acabamento.

Aug 8, 2018

By J. C. Kerkering, P. M. Daling

This paper discusses a study performed to evaluate the feasibility of transferring formal system safety assessment technology to the mining industry. A representative listing of formal techniques was evaluated to select the most useful methods for the mining industry to implement. Criteria for selecting methods included the interests, needs, and requirements of mine safety officials. This paper describes one of the selected methods, preliminary hazards analysis (PHA), and illustrates the analysis procedure for a mining example. This study also includes an assessment of the adaptability of selected methods to a user-interactive computer system for use by mine safety personnel. This paper includes a description of a conceptual computerized PHA-type safety program that facilitates performance of the safety analysis and can accommodate updates and revisions as necessary.

Jan 1, 1983

By Jeffiey B. Austin, Maurice Tagami

"The ores of the Iberian Pynte Belt are typically massive sulphide ores with very fine grained mineral textures. EuroZinc Mining Corporation is currently evaluating one of the massive sulphide deposits located near the town of Aljustrel, in South Central Portugal. The deposit contains significant grades of lead, zinc and silver. The ores are comprised solely of sulphide mineralization consisting of pyrite, sphalerite, galena and some secondary copper minerals. Liberation requirements for these ores are typically 22 to 25 microns. A selective flotation process has been utilized to produce separate lead and zinc concentrates for sale to off-site contract smelters.This paper outlines the process test results and describes the process parameters required to optimize the process parameters. Ths test program has been conducted in support of the re-opening of the facilities in Aljustrel. The 3500 tpd mining and milling facility was commissioned in 1990 and operated for 18 months before closing. The previous facility was designed to produce three products using a selective copper-lead-zinc flotation process. EuroZinc Mining Corporation is proposing to re-open the operation, selectively mining from a lead-zinc phase of the massive sulphide deposit and produce only lead and zinc concentrates.Results are presented and discussed.PROJECT HISTORY AND CURRENT PROJECT OBJECTIVESThe EuroZinc Aljustrel Project is a potential major producer of lead, zinc and silver located in the Iberian Pyrite belt of south-central Portugal. The town of Aljustrel is historically associated with mining dating to the time of the Romans. The area is rich in pyrite deposits, and sections of the pyrite deposits contain significant zones of copper, lead, zinc and silver. Mining in Aljustrel during the last century (1900’s) included a major pyrite mining operation, which produced feed for sulphuric acid production. Pynte mining operated from the 1930’s to the early 1970’s and a short-lived base metal operation from 1989 to 199 1."

Jan 1, 2000

By R. G. Knickerbocker, T. E. Evans, D. R. Torgeson

"INTRODUCTION Sponge iron is a product resulting from the reduction of an iron oxide at such a low temperature that fusion does not occur, and the reduced particles retain substantially the same shape as the original ore. The removal of oxygen in the reduction process leaves the metal porous and reactive. Sponge iron may be compared in general to a chemically precipitated substance insofar as reactive properties are concerned. The high specific surface and the orientation of metallic structure are factors which probably contribute to the reactive properties of sponge iron.The term ""gaseous reduction,"" as applied to iron ores, required clarification. Strong evidence exists, for example, that ore is partly reduced to sponge iron by carbon monoxide in the blast furnace at temperatures around 800° C. at a point that may be as high as 30 feet above the tuyores. In 1923 and 1924, Sims and Wood attempted to reduce iron oxide with carbon in an Arsem vacuum furnace at 980° C. These investigators found that only 6 percent of the iron was reduced to metal when the iron oxide-carbon mixture was heated for 1 hour under evacuated conditions, whereas at atmospheric pressure 70 percent of the iron was metallized. Their results indicate that the process of iron-ore reduction at temperatures below the melting point of the ore may proceed largely, if not entirely, by the action of reducing gases even when the reducing agent is solid carbon. Therefore, the term ""gaseous reduction,"" as used heroin, is defined as a process in which iron ore is brought into intimate contact with a reducing gas produced in separate-equipment from the reduction chamber itself.A large amount of pilot-plant development on gaseous reduction of iron ores has been carried out by the Bureau of Mines at the Boulder Experiment Station and had as its objective the reduction of fine iron ore by means of producer gas. The use of use gas was prompted by two considerations: First, the possible utilization of large reserves of Western noncoking bituminous coals and lignites contiguous to iron-ore drewwing; and second, an investigation of the results that might be achieved in the pilot-plant gaseous reduction of fine iron ores by means of a relatively reducing gas. The results obtained, it was felt, would be of considerable value in indicating the direction which gaseous reduction experimentation must take for the development of a commercially practicable and economic process for the production of sponge iron."

Dec 1, 1946

By Valerie Kollonitsch

Functional mineral pigments are used in large quantities in paint, paper, plastics, rubber, textiles, agriculture, and several other industries. U.S. consumption in 1969 is estimated at over 5 million tons a year, valued at nearly $150 million, as shown in Table 1. Originally extender pigments were employed only to lower cost. They were thought of merely as adulterants to replace more expensive prime pigments and binders. However, over the years their role has become better understood, and today their main functions are: - Increasing strength, stability, and service life. - Improving surface properties. - Enhancing application and processing properties. - Extending prime pigments. - Controlling viscosity and package stability - Lowering overall costs of the finished product. The principal minerals used as functional pigments are kaolin, ground calcium carbonate, talc, and asbestos. Other minerals include barytes, attapulgite, diatomite, mica, ground silica, wollastonite, and nepheline syenite. Several synthetic products, including precipitated calcium carbonate; precipitated, gel, and fumed silica; alumina trihydrate; and barium sulfate, compete with mineral products. They are more expensive, but often have more closely controlled particle size or other properties because they can be tailor-made according to the requirements. This paper covers only natural products selling for $10 or more a ton, approximately the lower limit for pigment grades. Data refer only to consumption in pigment applications. For example, such applications as filter aids for diatomite are not included. Key properties of the major mineral pigments are given in Table 2. It is important to note that these properties are primarily physical rather than chemical. In general, these products are sold to performance specifications for what they can do rather than on chemical composition specifications on what they contain.

Jan 1, 1969

By Gabriel Filipe Barrelas Marques Gamito Cardos

O aço em estudo (SAE8620MOD) é um material utilizado na aplicação de estruturas de óleo e gás. Essa liga modificada é utilizada em estruturas off-shore para produção de amarras. Para garantir a qualidade do produto são realizadas uma série de ensaios, dentre eles propriedades mecânicas (RT, LE, Alongamento e redução de área) bem como resultados de dureza e impacto. O ensaio de impacto está relacionado diretamente com a microestrutura obtida durante o processo de solidificação do aço e com o tratamento térmico realizado. Microestruturas com alto grau de bandeamento podem comprometer a variabilidade dos resultados de impacto. A redução ou até mesmo a eliminação do bandeamento é um caso de amplo estudo, principalmente em aços com processo de lingotamento contínuo. Muitas soluções já foram propostas para a redução do bandeamento, o de agitação eletromagnética tem se mostrado bastante efetivo na redução dos níveis de bandeamento e segregação dos produtos lingotados. O ensaio consiste em avaliar a intensidade do campo eletromagnético (FEMS) para o comportamento do nível de bandeamento do material. Foi utilizada uma corrida para teste via lingotamento contínuo, onde a velocidade de lingotamento permaneceu constante e variou-se a corrente dos agitadores em três condições: tarugos com baixa agitação (FEMs com corrente baixa), tarugos com alta agitação (FEMS com corrente alta) e tarugos sem agitação (FEMS desligado). Com baixa agitação no FEMS conseguimos obter um nível de bandeamento menor se comparado com os outros resultados. Como consequência a variação dos valores de impacto apresentaram-se menores que as demais condições, devido a homogeneidade do material. Dessa forma podemos dizer que a redução do nível de bandeamento no material reduziu também a variação dos resultados de impacto, tornando o processo mais estável.

Oct 30, 2017

In spite of a global economy that continues to seesaw and a U.S. Congress that is at odds with the president and themselves, cities around the world are still spending billions on their infrastructure. And that bodes well for the underground construction and tunneling industry and the professionals who work in it. In June, 1,405 of those professionals gathered in San Francisco, CA for the Rapid Excavation and Tunneling Conference (RETC). In addition to the first rate technical programming, attendees were able to see first-hand the latest in tunneling technology from 127 exhibitors who occupied 152 booths. Two short courses preceded the conference and two field trips were offered following the conference.

Jan 1, 2011

By Gary E. Parish

TABLE OF CONTENTS Contents I. Introduction II. Purpose of the Paper III. Historical Perspective A. Existing Sources B. New Sources (NSPS) C. Hazardous Pollutants (NESHAPS) D. Enforcement/Judicial Review 1. Title I Enforcement 2. Title III Enforcement 3. Information Gathering E. Summary IV. The Clean Air Act Amendments of 1977 (1977 Act) A. SIP-Related Provisions 1. Section 107(d) - Geographic Boundaries 2. Section 108 - Air Quality Criteria 3. Section 109 – NAAQS 4. Section 110 – SIPs 5. Section 122 and Sections 402 and 403 of P.L 95-95 – Unregulated Pollutants 6. Emission Offsets – Interpretive Ruling (I.R.) B. PSD Provisions - Part C. 1. Regulations Under the 1970 Act 2. The 1977 Act 3. Regulations Under the 1977 Act C. Visibility Protection - Part C, Subpart 2 D. Non-Attainment Provisions - Part D E. Monitoring and Modeling F. NSPS G. NESHAPS H. Enforcement/Judicial Review 1. Title I 2. Economic Enforcement 3. Title III Enforcement/Judicial Review (a) Section 304 (b) Section 307 4. Summary V. Special Problems and Opportunities for the Uranium Industry A. End Use B. Transportation C. Milling/Processing D. Extraction E. Exploration/Discovery F. General VI. Conclusions Appendix A Footnotes

Jan 1, 1979

By Joseph Irons, David Westfall

Three rock tunnel sewer systems are underway in the Chicago Area. (Figure 1) The three are designed to act independently and to be later connected to the future tunnels of the master plan. The tunnel excavation for each of the systems has been completed. One is in the Northwest area within the City being built by the City, known as the Lawrence Ave. System. Another is in the Southwest suburbs, known as the LaGrange-Brookfield Sewer or Southwest 13A, being built by the Sanitary District, the third is in the South suburbs called the Crawford Avenue sewer or Calumet 18-E, Ext. A- being built as a joint venture between the City and the District. The three are similar in that they have the same purpose, the same component parts and their tunnels were constructed in the nigaran limestone using a mechanical mining machine. The purpose of each of the systems is two-fold. First to provide flood relief for existing inadequate sewer systems, and second to reduce the pollution load to the waterways caused by combined sewer overflows. The existing systems in the areas to be relieved are combined sewers built many years ago. The main outlet for the Village of LaGrange, for example, was built in 1908, is badly in need of repair and lacks the capacity to handle the flood flow from the heavily urbanized area it now serves. The dry weather flow from the area is taken off by intercepting sewers. However during

Jan 1, 1997

By Osamu Taki

The development of new auger bits for soil cement column drilling equipment has made it possible to create a homogeneous mixture of soil and cement-reagent slurry. As a result, soil-cement columns are used for foundations of houses and buildings, with reliable results, as demonstrated by many field projects and laboratory tests. This paper presents and discusses construction techniques for soil-cement columns, characteristics of the soil-cement solid, quality control, bearing test results, and soil-cement foundation design procedures.

Jan 1, 1992

The usual metallurgical, engineering and administrative activities associated with the handling and smelting of ores, and the subsequent handling and treatment of the products of smelting, present also problems of hygiene that engage the earnest attention of executives in all well-managed concerns.Again, associated with the employment of any considerable number of men, there is always present the problem of accident prevention.INDUSTRIAL HYGIENE.In the earliest records of lead min.ing and smelting there are references to the injurious effects of lead oh the health of the employees, and, with the advancement of medical science, lead poisoning has been the subject of many works by various authorities in many countries.Moreover, in practically every civilised country, there are laws governing the conduct of the lead industry, and in most cases these laws stipulate that employees shall receive compensation for disability caused by lead poisoning.This provision gives the problem an economic aspect. Apart from the legal and the economic aspects, however, there is the humanitarian aspect, which implies that the...

Jan 1, 1937

By Alessandra Souza Martins

O aço inoxidável super duplex vem apresentando um desempenho satisfatório em ambientes de maior agressividade. Esse tipo de aço possui boas propriedades de resistência mecânica, resistência à corrosão e tenacidade ao impacto. Entretanto, mesmo apresentando desempenho satisfatório, esses aços podem apresentar problemas de corrosão quando sofrem algum tratamento térmico, devido à precipitação de uma fase deletéria chamada de alfa linha (?’), a qual precipita em temperaturas entre 300°C e 550°C e pode ocasionar uma diminuição da resistência à corrosão e tenacidade do material. Portanto, o objetivo deste trabalho é avaliar a resistência à corrosão dos aços inoxidáveis super duplex de grau 5A e 6A após sofrerem tratamento térmico a 475oC. A diferença entre os aços de grau 5A e 6A ocorre na presença de cobre e tungstênio na composição química do aço com grau 6A. A resistência à corrosão dos corpos de prova foi avaliada por meio das seguintes técnicas eletroquímicas: polarização anódica, espectroscopia de impedância eletroquímica e temperatura crítica de pite. A resistência mecânica dos corpos de prova foi avaliada por meio da técnica de dureza Brinell. Foi realizada também a caraterização microestrutural e a quantificação das fases do material. Os resultados mostraram um aumento da dureza do material, indicando um aumento da presença da fase ?’ com 10 horas de tratamento térmico apresentaram maior resistência à corrosão.

Aug 8, 2018

By C. G. Dunn

James, Jones, and Leak (JJL) conclude that growth-rate and orientation-distribution data obtained in a steep thermal gradient should be used with caution to account for isothermally produced recrystallization textures. I agree. However, it is not clear whether they conclude a) that the orientation dependence of rate of growth of secondaries in (commercial) silicon iron depends on both temperature and a temperature gradient or b) that, in applying rate data obtained in a steep thermal gradient, the isothermal annealing temperature must be close to the temperature for which the rate data apply. Also, it is not clear what tem-

Jan 1, 1967

By R. Sweennen, A. Vervoort, J. Caers

A case study is presented of the mechanical behaviour of fractures in the Westphalian A and B siliciclastic succession of mud-, silt- and sandstones with intercalating coal layers in the Campine basin of northeast Belgium. Mining ceased in the area in 1992 and a pilot well was drilled to assess the feasibility of methane extraction by hydraulic fracturing. Work was carried out to study the influence of types of cement fill in fractures on the shear behaviour of the rocks by comparison with that of the coal seams. X-ray computerised tomography was used for visual appraisal and selection of jointed rocks before destructive shear testing was carried out. Two major type of veins were found to be present, one cemented with carbonate and the other with kaolinite or kaolinite/carbonate. Uniaxial compressive strength and shear tests showed that differentiation of the two types of veins was vital in evaluating the strength of the sandstones, as cementing of the fractures by rigid carbonate minerals can reinstate the strength of the rock masses to that of the intact material. Kaolinite was more susceptible to plastic deformation than carbonates

Jun 19, 1905

By S. F. Ye, L. Xiao, Y. L. Wang, P. W. Han

"Copper anode slime is a precious secondary source for the recovery of silver. However, current recovery process are constrained by either sever pollution or high cost. To cover the drawbacks of current process, this research employed a novel strategy by using the manganese dioxide as the oxidant in acid solution, which avoided the generation of sulfur dioxide while high silver extraction rate was achieved. The effects of manganese dioxide, sulfur acid concentration, stirring speed, temperature and leaching time on silver extraction rate were investigated. The silver recovery reached to 91.68% under the conditions of 1.2 g manganese, 2.0 mol/L H2SO4, 300 rpm, 80 °C and 6 h. INTRODUCTION Copper anode slime is generated from the electrolysis refining of copper and is extremely precious for its containing noble metal such as silver (Chatterjee, 1996; Amer, 2003; Yldrm et al., 2014; Syed, 2016; Wang et al., 2017). Therefore it is of great significance to extract silver from anode slime for the full utilization of resource. Pyrometallurgy is the most mature process for the extraction of silver because of its stability and adaptability (Hait et al., 2009; Zhao et al., 2010; Gao et al., 2017). However, it also suffers the drawbacks of high operating cost, low extraction rate of silver and severe pollution of smoke dust (usually containing lead and arsenic) (Ludvigsson and Larsson, 2003). To cover the drawbacks of pyrometallurgy process, more and more attentions are giving to the semi-hydrometallurgy process which usually includes a pretreatment process of sulphatising roast or low temperature oxidizing roasting (Tishchenko, 1964). After pretreatment, the refractory silver bearing phases (silver selenide, silver sulfide and silver) are converted into readily leached forms which are often extracted by ammonia, sodium sulfite in alkaline solution (Valiuniene et al., 2010; Wojciech, and Kitka, 2017). Despite its relatively high extraction rate and low investment, it still has the disadvantages of releasing harmful gases since the sulfur dioxide are generally generated in the pretreatment process. In addition, the use of ammonia can easily lead to a leaking into the atmosphere once not carefully dealt with (Aylmore and Muir, 2001). As for silver recovery by sulfite leaching, the consumption of sodium sulfite is rather high which often results in a pipe blocked (Yang et al., 2006)."

Jan 1, 2018

To predict the spontaneous combustion potential of bituminous coals using a simple expression based on an easily acquired coal property. Background Approximately 20% of underground coal mine fires in the United States since 1978 have been attributed to spontaneous combustion. Spontaneous combustion fires in underground mines are most likely to occur in gob area; and are difficult to detect and to extinguish by direct fire fighting methods. Often, sections of the mine or the entire mine must be sealed for long periods, at a great economic loss to the mine operator, mine employees, and the surrounding community. It is conservatively estimated that the cost of scaling a large mine is about $50 million.

Jan 1, 1989