Search Documents

By Gustavo Nucci Franco

A indústria do aço passa por seu pior período no Brasil e as empresas vêm buscando soluções para minimizar custos e garantir as operações com menos recursos. Ponto importante nessa busca de ganhos potenciais, a Logística vem, assim, merecendo uma atenção especial. Este trabalho apresenta esforços da AM Juiz de Fora, em parceria com a Franco Arbeit Engenharia, para reduzir o tempo de permanência de veículos em sua unidade e, com isso, evitar custos com o pagamento dos novos valores de permanência. Para isso, foram utilizadas modernas ferramentas de Simulação em Computador para que as soluções mais adequadas pudessem ser implementadas com sucesso.

Aug 17, 2017

By C. Siyasiya

One of the problems that is occasionally encountered during the continuous casting of DIN 1.4003 stainless steel (hereafter referred to as 1.4003) is the side bulging effect, a problem that is generally prevalent in ferritic stainless steels. This occurs because the unconstrained narrow sides of the solidification shell are not able to withstand the ferrostatic pressure once the strand has emerged from the mould. Coupled with side bulging, there is strand width variation at high temperatures, i.e. when the steel is in the ferrite-austenite dual phase region. Both of these dimensional changes to the slab profile create some processing problems in subsequent hot rolling operations when unacceptable width variations are encountered. The strength of the solidification shell and its ability to withstand the ferrostatic pressure during continuous casting is dependent on its thickness and phase composition when exiting from the mould up to a few metres downstream. From the study of the high temperature metallurgical behaviour of this steel, it was observed that a thicker solidification shell when exiting from the mould and a higher austenite volume fraction in the steel would be favourable for the reduction of the side bulging effect during continuous casting. It was also found that as long as the d-ferrite to austenite phase ratio keeps fluctuating due to variations in chemical composition and process control in the dual phase region from cast to cast, the strand width variation problem would probably persist. The remedy to this effect lies in more strict chemical composition and process control during continuous casting of this steel. The hot ductility experiments revealed that 1.4003 exhibits good hot ductility in the strand straightening temperature range with a minimum of 75 per cent reduction in area and this was attributed to the high volume fraction of ferrite (0.2 to 0.4) in the steel. This would provide a remedy to side bulging by increasing the secondary cooling rate of the strand in order to form a thicker solidification shell without necessarily risking transverse cracking and other surface defects during unbending. Keywords: side wall bulging, resistance bending moment, applied bending moment, ferrostatic pressure.

Jan 1, 2005

By M. Massinaei, M. R. Yarahmadi, S. Zeidabadi, M. Oliazadeh

"Although the majority of new flotation column installations continue to be for cleaning or recleaning, an increasing number of flotation projects are specifying columns for roughing or scavenging duties. NICICO has recently installed flotation columns operating in rougher, cleaner and re-cleaner circuits at three new copper concentrators; Miduk, Sungun and Sarcheshmeh. Miduk is probably one of the unique operations that use flotation columns in a rougher circuit. The Miduk rougher circuit comprises five CISA parallel columns. The rougher concentrate constitutes 88% of final concentrate and reports to concentrate thickener. The rougher tailings are scavenged with ten 50 m3 mechanical cells. The scavenger concentrate is then reground and cleaned in three 3.2 m columns in parallel. The cleaner tailings are scavenged in six 50 m37mechanical cells. The cleaner tailings along with the rougher scavenger constitute final tailings.In Sarcheshmeh, the cleaner concentrate is re-cleaned in a column. The column tailings are sent back to the cleaning circuit and the concentrate is reported to the concentrate thickener.This paper reviews performance details of the flotation columns utilized in rougher circuits at Miduk and compares their metallurgical performances in an industrial scale with columns at cleaning circuits for copper flotation. Practical limitations for applying the flotation columns in rougher circuits will be discussed in details.INTRODUCTIONThe use of flotation columns has grown rapidly since the first successful commercial application at Mines Gaspe, where columns were used in a cleaning circuit to float molybdenite. Early applications of columns were restricted to replacing or adding final cleaning stages in existing circuits. Columns can achieve superior cleaning as compared to conventional cells due to their ability to support a large froth depth and the use of water for washing froth. Wash water travels down through the froth and crosses the pulp/froth interface, replaces the entrained particles reporting to the froth from pulp and improve the concentrate grade."

Jan 1, 2011

By William C. Harrigan, William D. Nix

Dynamic measurements of Young's modulus have been made for poly crystalline Ni-W alloys from room temperature to 800°C. The alloys studied range in composition from pure nickel to Ni-10 at. pct W. The results indicate that Young's modulus decreases linearly with temperature above the Curie temperature. The rate of change of Young's Modulus with temperature mas found to range from 104 psi per "C for pure nickel to 0.82 x 104 psi per °C for Mi-10 pct W. At all temperatures the elastic modulus decreases with increcrsing tungsten content up to 1 at. pct W, and increases as the tungsten content is increased above that level. Young's modulus decreases slightly as the carbon content is increased from 0.002 to 0.09 wt pct C THE knowledge of the elastic modulus of metals and alloys is important for a number of reasons. The first and most obvious reason comes from the need to predict elastic deflections under given loading conditions. A second and somewhat more subtle reason comes from the fact that the elastic properties of an alloy must be known before a proper account of the mechanisms of plastic deformation can be made. This is especially true for high-temperature creep of crystalline solids. Sherby and his coworkers have shown that the high-temperature steady-state creep rates of crystalline solids are inversely related to the elastic modulus1,2 and that the temperature dependence of the elastic modulus must be taken into account if reliable determinations of the activation energy for creep are to be made. In addition, measurements of the elastic constants of solid solutions are needed to allow one to assess the modulus interaction contribution to solid-solution Strengthening.3-5 Pelloux and Grant6 have demonstrated that substantial solid-solution strengthening at room temperature and elevated temperatures occurs when refractory metal solute atoms are added to nickel. While the high-temperature elastic properties of pure nickel have been measured by a number of authors,7-10 the elastic properties of nickel-based refractory metal alloys have not been determined. The purpose of this paper is to report on measurements of Young's modulus of polycrystalline Ni-W alloys at elevated temperatures. It is expected that these measurements will be valuable to studies of the mechanical properties of nickel-based refractory metal solid solutions. I) EXPERIMENTAL Young's moduli of polycrystalline samples were determined by a dynamic method in order to reduce high- temperature anelastic and plastic relaxations. The samples were forced in transverse free-free vibration; that is, both ends of the sample were unrestrained and the vibration was transverse to the long axis. The fundamental resonant frequency was determined by the Forster method.11 The analysis of this type of vibration which was formulated by Rayleigh,12 Timo-chenko,13 and pickett,14 and reviewed by Fine," leads where fn is the resonant frequency of the nth mode, r is the radius of the circular cross section. L is the specimen length, ßn is 1.5056 for free-free vibration in the fundamental mode of vibration, 6 is the mass density, and E is Young's modulus in the axial direction. This equation can be transformed into: E = 9.17605 x 10-6(L/D)E/Lf2 [2] where E is Young's modulus in psi, L is the length in inches, d is the diameter in inches, W is the weight in grams, and f is the resonance frequency in cps. Eq. [2] was further modified in order to take account of the thermal expansion of the samples. The resulting correct term is: where the thermal expansion coefficients for nickel and tungsten, respectively. Xw is the atom fraction of tungsten in the sample and T is the temperature in "C. The treatment of the thermal expansion coefficient as a linear function of composition seems sufficiently accurate since an error of 25 pct in the expansion coefficient will result in only a 0.3 pct error in the modulus at 1000°C. A) Apparatus. The equipment for this investigation has been described by Lytton et al.16 Several modifications of the equipment have been made. The most significant change involved replacing the detector crystal transducer with a magnetic transducer. A phonographic magnetic transducer was employed as a sensing device since the contact pressure necessary to produce a stable signal is much less than that for a crystal transducer. This magnetic transducer is also not affected by conditions of high temperature and vacuum which are present in these experiments. The vacuum was 10-5 torr at room temperature and about 5 x 10-4 torr at 900°C. This was sufficient to prevent surface contamination of the samples during the tests. The samples were heated in an elliptical furnace with a quartz lamp at one focal line and the sample at the other, as described by Lytton et a1.16 The temperature of the sample was measured by monitoring the

Jan 1, 1969

By Yeruva Ramanareddy, Sohail Wajid, Ahmed Shaz, K. Bhavani

"CP-06 is an NATM cross passage which connects up-line and down-line metro tunnels near Kilpauk Medical College, Chennai. It lies completely in loose silty sand to dense sand with water table almost touching the ground surface after Chennai floods. Pre-grouting was done before excavation to seal the area and to ensure no-loose pockets. The heading was excavated successfully but while benching excavation huge water ingress started seeping out. Sand also permeated along with water which became unstoppable due to cavity formation and caused the up-line tunnel to sink considerably. A large grouting exercise was carried out with different grout materials and techniques both from the ground surface and inside of tunnel to stop the water ingress and stabilize the tunnel. This paper describes the chronology of events that occurred in the tunnel during CP-06 issue. It elaborates all the different grouting techniques involved in the whole process of the tunnel stabilization. It includes a finite element analysis using Rocscience RS2 9.0 software showing the possible cause of sand incursion with water from the CP invert which lead to the tunnel settlement. This paper also describes the after effects and the lesson learnt from the whole incident.INTRODUCTIONConstruction of Metro Rails has become the latest alternative to cope up with the transportation demand of the growing urban cities population. L&T SUCG JV constructed Chennai Rail Metro Phase II Contract UAA-04 which included design and construction of approximately 4 km of route length of underground mass transit railway including 3 underground stations. This package also includes 12 cross passages which are NATM tunnels connecting upline and down-line side of TBM tunnel for safe evacuation of passengers in case of emergency. As per NFPA guidelines, this is a mandatory structure and there should be atleast one cross passage in 244m tunnel length.CP-06 is a cross passage connecting upline and downline tunnel between Pachiyappa College Station and KMC Station, in Chennai Metro. During the construction of CP-06, heavy water seepage of around 450 liters per minute was encountered during second round of benching excavation after full heading was excavated. An inflow of around 12-15 cum of sand and silt was also observed inside the tunnel along with the seepage water, which created piping inside the TBM tunnel causing it to settle continuously with time. A huge effort was made to stop the water ingress along with loose sand which was causing the running tunnel to settle, involving all possible grouting methods and temporary support installation."

Jan 1, 2017

By J. M. Houston

"In October 1982, Rio Algom Limited, purchased a tin prospect near East Kemptville, Nova Scotia, from Shell Canada Resources. This purchase led to the development of the first substantial tin mine in North America. This paper deals with the drillingand blasting operations at Rio Algom, in particular the use of emulsion explosives technology.This presentation describes what emulsion explosives and Heavy AN/FO are, and the support system used to deliver these products to the blast site.HistoryThe East Kemptville mine site was discovered by Shell Canada Resources (SCR) in July 1978. SCR started diamond drilling on the tin prospect in March 1979. After 8220 m of BQ drilling, it was estimated a reserve of 56 000 000 tonnes of 0.165% Sn was present.The property, which is located 54 km northeast of Yarmouth, Nova Scotia (Fig. 1), showed, after a feasibility study that, given an ore treatment rate of 9000 tonnes per day, a mine life of 17 years could be expected.GeologyThe tin deposit of the East Kemptville Mine, occurs in granitic rocks at their contact with metasedimentary rocks. The mineralization is in the form of cassiterite with associated sulphides of copper and zinc. The tin occurs in a stockwork of tin bearing Greisen alteration zones.East Kemptville MineThe mine planned an open pit operation with the first five years being mined at a rate of 14 000 tonnes per day, of which 5000 tonnes will be waste and low grade ore. Eventually, the total mining rate will be 21 000 tonnes per day, including 12 000 tonnes of waste and low grade ore. Figure 2 shows the general layout of the mine site.East Kemptville Chooses Emulsion ExplosivesIn December 1984, East Kemptville Mine awarded the Explosives Division of C-I-L Inc. a contract to supply explosives to the borehole. The system chosen gives East Kemptville the on-the-bench choice of regular AN/Fa, or a high density, Heavy AN /Fa product called SuperAN· or a water resistant emulsion explosive called MAGNAFRAC· for holes that cannot be dewatered.Emulsion ExplosivesAn emulsion is an intimate mixture of two liquids that do not dissolve in each other. Emulsions have contributed to our daily lives in such products as insecticides, salad dressings and cosmetics."

Jan 1, 1987

By Fabrice Mathieu

The Cutter Soil Mixing (CSM) provides a cost effective solution for the rapid construction of retaining and cut-off walls using new equipment developed from diaphragm wall cutter technology. CSM consists of cutting and mixing drums mounted on compact hydraulic motors. Soletanche Bachy CSM has been designed to leave the space above the tool free, thereby mixing the soil efficiently during all the phases of the wall construction, with high penetration rates. The precise positioning and verticality of the wall is achieved using a kelly bar and full monitoring. Soletanche Bachy CSM is a versatile equipment which can be mounted on various carriers: pile rigs, hydraulic crane, carrier equipped with telescopic mast. The major phases of Soletanche Bachy CSM development are presented, including the results of an extensive trial carried out in Le Havre (France). The soil consists of hydraulic fill with soft soil lenses overlying sandy deposits. 20m deep panels were constructed to support a rectangular shaft. During the construction, and after its completion, the shaft was subjected to an extensive series of tests followed by a partial excavation. The paper discusses also the future development of the technique and its potential applications.

Jan 1, 2006

By Y Sha

During the last two decades, China has expanded its iron and steel industry very quickly, from less than 100 Mt/a steel production to over 700 Mt/a. It caused big increases in both domestic iron ore production and imported iron ore quantities year by year. The mode of iron ore supply has changed from almost all domestic supply to major tonnes of imported ore plus domestic ore supply. Over 200 blast furnaces with volumes larger than 1000 m3 each have been built and put into operation. Sinter machines have been enlarged quickly. There are now 135 sinter machines with =200 m2 sintering area each. Pellet production increased from 11.94 Mt in 1999 to 210 Mt in 2011, resulting from rapidly increasing domestic concentrate supply and rapid development of the grate-kiln process. The typical ferrous burden constitution is high basicity sinter plus pellets plus lump. The pellet proportion increased and the sinter proportion decreased gradually. A lot of technical improvements, like deep bed sintering, sintering with a high ratio of limonite, composite sintering, pellet process optimisation, a high ratio of hematite in pelletisation, blast furnace operation with low-grade ferrous burdens and hazardous element control, etc have been made to enhance iron burden quality and to reduce hot metal cost. Chinese iron and steel production is expected to increase slightly in the next few years. Its overcapacity should be controlled effectively. Given the variations of iron ore supply, pellet production will keep progressing in terms of production scale and pellet quality, the sintering process will be improved further by various measures to utilise different ores efficiently, and ferrous burden constitution will be optimised continuously to realise the lowest cost of hot metal production.CITATION:Sha, Y and Wang, Z, 2013. The Chinese iron and steel industry response to the challenges of iron ore supply, in Proceedings Iron Ore 2013 , pp 7-14 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By D. K. Bose, R. H. Rakhasia, V. D. Shah, J. C. Sehra

A series of experiments was conducted to determine the effects of roasting temperature, soaking period and quantity of soda ash added. At a laboratory scale, under optimum conditions of roasting at 873 K for 2 700 s with soda ash 10 wt% in excess of stoichiometric, molybdenum recovery was 99%. The investigations indicate the technical feasibility of producing high-purity MoO3 by combining the roasting process with carbon adsorption/desorption. The process uses low-cost chemicals, can be scaled up readily and is free of the SO2 pollution generated by conventional roasting, as the sulphur content of the concentrate is converted to sodium sulphate

Jun 18, 1905

By Alexandre Magno Alves de Oliveira

Os resíduos provenientes das indústrias cerâmicas demandam locais apropriados de descarte, gerando gastos, desperdício de matérias-primas e, quando o local de descarte é impróprio, problemas ambientais. Sendo assim, se faz necessário o estudo da reutilização destes resíduos, tanto para fins econômicos quanto ambientais. Dessa forma, a reutilização de chamote, resíduo oriundo do descarte de materiais cerâmicos, é possível através da sua incorporação em massas cerâmicas para a produção de novos materiais (blocos, tijolos, telhas, etc). O presente trabalho teve como objetivo analisar a influência do chamote em massas cerâmicas, comparando dosagens com substituição de 10%, 20% e 30% em massa com um traço de referência. Para isso foram realizados ensaios, com os quais pode-se obter as propriedades relacionadas a retração por secagem e por queima, absorção de água, perda ao fogo, porosidade aparente e tensão de ruptura à flexão. Em suma, pode-se concluir que o uso do chamote permite a obtenção de materiais com boa resistência mecânica, moderada absorção de água e com boas propriedades dimensionais, demonstrando ser uma alternativa ambientalmente amigável e economicamente viável.

Oct 30, 2017

By Jovanir Francisqueto

O objetivo deste projeto foi elevar a produtividade do pátio de placas do Laminador de Tiras a Quente da ArcelorMittal Tubarão através da alteração do processo de sequenciamento do Laminador de Tiras a Quente com a criação do processo de realocação de placas após a formação da chance de laminação. O trabalho iniciouse com a definição de regras metalúrgicas de realocação de materiais e definição dos critérios operacionais e de atendimento a pedidos para posteriormente ser desenvolvido o software de otimização para a execução da realocação automática de placas na chance de laminação com foco na redução de movimentações no pátio do Laminador de Tiras a Quente. Com a implantação do processo/sistema espera-se conseguir uma redução de aproximadamente 60% nas movimentações de placas para formação da chance de laminação, conforme demonstrado nas simulações com dados reais e consequentemente reduzindo número de paradas de forno em função de problemas de produtividade do pátio de placas visando o aumento da produção do Laminador de Tiras a Quente em torno de 15 Kt/ano.

Aug 16, 2017

By Elaine T. Cullen

Human beings are natural storytellers and story listeners. We learn very early that stories entertain us, but also give us the ?rules? about what is expected of us and how to make meaning of our experiences. Stories are integral to our lives, and have great power to change or influence how we think or how we react. They are an innate part of how we learn, and have obvious benefits to trainers or educators who are trying to impact what and how we learn. This paper and presentation discuss the social and cultural power of stories, and how they have been used to develop training for skilled blue-collar workers. Included will be examples as well as suggestions for trainers on where to find stories, what type of stories to pay attention to, and how to use them to improve occupational safety training.

Jan 1, 2008

By Marianne Snedeker

In September 1985 we published a questionnaire asking about the content of MINING ENGINEERING and about your interests. By Dec. 10, our cutoff date, we had 430 responses, representing about 1.5% of the 28,238 people who received the September issue of ME. In the data that follow the tabulation and percentages are based on the number of individuals who responded to the particular question. About ME Through responses to the questionnaire, we were hoping to learn more about you, your interests, and how the magazine could better serve you. Those of you who responded told us something positive - you look at or read the magazine. Of the 430 respondents, 428 or 99.5% indicated that they had read or looked through the July and/or August issues. Those of you who refer to the magazine once are 207 or 48.5%. Those of you who refer to the magazine two or three times are 193 or 45.2%. Those of you who refer to the magazine four or more times are 27 or 6.3%. How much time do you spend reading the magazine? Of those responding to this question: 64 spent up to 1/2 hr 15.0% 224 spent up to 1 hr 52.6% 115 spent up to 1-2 hr 27.0% 23 spent more than 2 hr 5.4% In an informal survey among our staff, we determined that most people spend 1/2 to 1 hr reading magazines to which they subscribe at home. Does that match your experience? Many of you, 335 or 79%, clip your magazine for further reference. Also, many of you, 313 or 73.6%, do not pass your copy on to another reader, indicating that you are clipping it or receiving the magazine at home. Those magazines that are passed on reach: 1 person 3 0.7% 2 people 64 15.1% 3-5 people 34 8.0% 5 or more 11 2.6% Answers to what portions of the magazine you find useful indicated that the top three were Industry Newswatch, feature articles and Technical Papers; see Table 1. The "other" category included advertising - display, classified, Employment, and Professional Services - Washington Survey, New Products, Free Literature, book reviews, technology news, and Coming Events and Short Courses. We asked your appraisal of the technical level of the magazine. Of those responding, 39 or 9.1% indicated that it is too technical, 55 or 12.8% indicated it is not technical enough, and 335 or 78.1% judged it to have the correct technical level. In response to the question about whether you like to read an occasional feature that is not technically oriented, 21 or 5.1% said no, but an overwhelming 94.9% (393) said yes. Of the specific

Jan 1, 1986

By P. den Hoed, J. Nell

Tests were conducted on samples of rutile, titaniferous slag and ilmenite; each sample was mixed with coke and chlorinated in a bubbling fluidized bed at 1000°C. Profiles of the rates of chlorination of species were constructed from chemical compositions of the bed residues at different durations. From the start FeO and MnO are chlorinated quickly and all but entirely in a fraction of the time it takes to chlorinate all the TiO2. When the level of FeO is significant, as in slag and ilmenite, FeO is chlorinated faster than TiO2is. In these oxides, there is an inverse relationship between the rates of chlorination of FeO and TiO2during this first stage; the relationship, moreover, correlates linearly with the initial percentage of FeO in the oxide. We identify three stages in the chlorination process; a first, in slag and ilmenite, when FeO is being chlorinated; a second, when TiO2is most readily chlorinated; and a third, towards the end, when the levels of TiO2are reduced to those of other species. The rates at which individual species are chlorinated are analysed in terms of their appreciation or depreciation with respect toTiO2

Jan 1, 2003

By T. A. Ngcobo

Paper written on project work carried out in partial fulfilment of BSc Eng (Mining)degree The purpose of this report is to assess the risks faced by mines in dolomitic compartments in particular Kloof 8 shaft. The dolomites of the West Rand comprise one of South Africa?s most natural water resources, and overlie the reefs of the richest gold mines in the world. The pumping of water from the dolomitic aquifers to prevent flooding has caused the natural water table to subside, and the resulting cavities within the dolomite rock formations that overlie many gold deposits sometimes collapse, causing sinkholes. These impacts of the mining industry could worsen over time if preventative measures are not taken. This report discusses these impacts in detail, more specifically the risks to which operations in dolomitic compartments are exposed. A risk analysis was carried out to access the risks that the organization could face and it was this analysis that allowed one to examine the best methods to combat the problems. Other factors such as geological features and seismic events were also considered for the evaluation. To aid with the completion of this work various resources were utilized. A literature study was undertaken, information was gathered from various experts who specialize in dolomitic studies, evaluations were conducted and conclusions reached. The results from the project indicated that preventative measures should be implemented and correct procedures put in place to prevent any disasters.

Jan 1, 2006

By Stephen M. Smading

Unique onsite assembly of a 12.43 m Main Beam TBM and back-up system was completed on September 18, 2008 in the remote mountains of the Sichuan province of China. The equipment was assembled onsite, without previously having been assembled and tested in a factory, utilizing a method called Onsite First Time Assembly (OFTA). The Jinping-II hydroelectric project features four parallel headrace tunnels approximately 18 km long, two of which will be excavated by TBMs and two by drill and blast. A nearby fifth tunnel is being excavated by a 7.2 m TBM to draw down ground water in advance of excavating the headrace tunnels. This paper addresses the following topics: ¦Project description including geology and terrain; ¦The decision process leading to onsite first time assembly, the assembly process and logistics, and lessons learned; ¦Design features of the TBM and back-up system; and ¦Operational history from startup to the writing of the paper.

By Y. Mitani, F. Vallier, T. Esaki

Shear-flow coupling tests are conducted using an original apparatus, and a shear-flow coupling model using Geographic Information System (GIS) is developed in order to evaluate shear-flow coupling properties of a rock joint. Shear-flow coupling tests indicate that the hydraulic conductivity of joint once decreases, and then rapidly increases at the shear displacement near the peak shear stress. The proposed model simulates the test results relatively well. However it indicates that it is difficult to apply the local ‘cubic law’ model in the initial shear stage, in which the change of selective flow path is remarkable. Scher-Fliess-Kopplungsversuche werden mit einem neuartigen Versuchsgerät durchgeführt und mithilfe von Geo-Informationssystemen (GIS) gedeutet, um so ein Modell für die Scher-Fliess-Kopplung in Gebirgstrennflächen zu entwickeln. Die Versuche zeigen, dass die hydraulische Leitfähigkeit zuerst abnimmt, dann aber schnell wieder zunimmt sobald die maximale Scherfestigkeit erreicht ist. Das vorgestellte Modell bildet die Testergebnisse relativ gut nach. Es zeigt auch, dass es schwierig ist, das lokale Cubic Law im Initialstadium der Scherbeanspruchung anzuwenden, in dem die Variationen selektiver Fliesswege gross ist. Les essaies hydro-mécaniques couplés en cisaillement sont réalisés grâce à un appareil éxperimental prototype et un modèle de couplage hydro-mécanique utilisant le S.I.G (systeme d'information géographique) développé dans le but d'évaluer les propriétés hydro-mécaniques des joint rocheux. Les résultats indiquent que la conductivité hydraulique des joints décroit puis augmente rapidement en se rapprochant du pic de cisaillement. Le modèle proposé simule relativement bien les résultats expérimentaux ; mais indique également qu’il est difficile d’appliquer localement la loi cubique au début du cisaillement où, les changements d’orientation dans le réseau d'écoulement sont considerables.

Jan 1, 2003

Fresh coal refuse was sampled at 21 US mines. Five of the sites were drilled, sampled and tested more extensively. Field tests included Standard Penetration tests, and in-situ density determinations. Laboratory testing included specific gravity, gradation, maximum, and minimum density tests, as well as 9-inch) drained triaxial tests, 9 and 10-inch, permeability tests, slake-durability tests, and accelerated slaking tests. Some refuse sites had significantly lower shear strengths and permeabilities in old, slaked or weathered material than in fresh refuse. Testing did not show useful correlations between strength and permeability changes and other material properties which could serve as "predictors". Testing of refuse under "accelerated slaking" conditions showed promise as a comparative tool and as a potential means of preparing artificially aged samples for evaluations of long-term behavior. The state-of-the-art in slaking research, and the implications of slaking on coal refuse disposal, and on practical methods of managing slaking, were also studied.

Jan 1, 1981

By Seth C. Schaefer

The Bureau of Mines has determined the standard Gibbs energies (AGf°) of CoS1.035 (cobalt sulfide) and Ni2.515S2 (nickel sulfide) with high-temperature galvanic cells using stabilized Zr02 (zirconia) as the electrolyte. Potential measurements were obtained for the cell Pt, CoS1.035, CoO, S02(g, 1 atm)//Zr02//02(g, 0.0114 atm), Pt, with the overall cell reaction C0S1.035(c) + 1.535 02(g, 0.0114 atm) = CoO(c) + 1.035 S02(g)¬ These results, combined with the best available data for ?Gf° of CoO and S02 from the literature, give the standard Gibbs energy of formation of CoS1.035 for the reaction Co(c) + 0 5175 S2(g) = CoS1.035(c) ?Gf° = -38.890 + 18.87 x 10-3T ± 0.185 kcal/mole (866.0 - 1,104.9 K), where temperature (T) is expressed in kelvins. Similar measurements were obtained for the cell Pt, N12.515S2, NiO, S02(g, 1 atm)//Zr02//02(g, 0.0122 atm), Pt, with the overall cell reaction Ni2.515S2(c) + 3.2575 02(g, 0.0122 atm) = 2.515 NiO(c) + 2 S02(g). Combination of these results with data for ?Gfo of NiO and S02 from the literature yields the standard Gibbs energy of formation of Ni2.515S2 for the reaction 2.515 Ni(c) + S2(g) = Ni2.S1SS2(c) ?Gf° -65.377 + 24.67 x 10-3T ± 0.541 kcal/mole (968.6 -1,053.7 K).

Jan 1, 1981

By W. S. Sanner

Anthracite was used extensively as a fuel in iron metallurgy from 1840 to 1880. In 1874, 226 of the 680 blast furnaces in the United States were operating on anthracite and producing almost one-half of the Nation's pig iron. However, by 1890, railroad expansion, the development of western iron-ore reserves, and the growing use of coke decreased the importance of anthracite as a metallurgical fuel. As a result, the last blast furnace designed exclusively for anthracite use was built in 1891. Because of the increased energy requirements of our expanding national economy, the abnormally high demands during national emergencies, and the proximity of anthracite deposits to eastern steel-producing areas, interest has grown in again using anthracite in iron metallurgy. Estimates of anthracite reserves indicate a 300-yr. supply at a production rate of 30 million tons per year. These large reserves dictate the development of an adequate technology for the use of anthracite by the metallurgical industry.

Jan 1, 1961