Search Documents

By L. Nahai

Iran's petroleum industry is nearly 50 years old and the oldest in the Near East. According to published figures, Iran ranks third in production and reserves in the Near East. These reserves (including probable reserves) are estimated at 35 billion barrels and constitute about 11 percent of the world's total. Iran is the sixth largest producer of crude petroleum in the world. The 1961 output of more than 430 million barrels was 5 percent of total world output for the year. In the same year, Iran ranked fourth among world petroleum exporters, providing 8.4 percent of total world exports.

Jan 1, 1963

By V. F. Parry

[Subbituminous coal or lignite when stored in random piles or in ordinary bins in which the temperature fluctuates and air circulates quickly undergoes objectionable physical and chemical changes, which decrease the utilization value of the fuel and increase its tendency to ignite spontaneously. Slacking takes place, and the heating value decreases. These changes are accelerated by fluctuations of temperature and by circulation of air through the storage space. When such coals are exposed to the weather they lose moisture rapidly. If evaporation from the surface of a lump proceeds at a faster rate than that at which it is replaced by moisture from the interior, the rate of shrinkage at the surface is greater than that at the interior; consequently, stresses are generated at the surface which cause the coal to disintegrate. Likewise, when moisture is absorbed by the air-dried surface the outside layers expand at a faster rate than the interior, which results in further break-down. As these cycles are repeated the lump may disintegrate completely. Therefore, successful storage of low-rank coals depends on control of the factors that influence change of moisture.]

Jan 1, 1941

By V. F. Parry

Subbituminous coal or lignite when stored in random riles or in ordinary bins in which the temperature fluctuates and air circulates quickly undergoes objectionable physical and chemical changes, which decrease the utilization value of the fuel and increase its tendency to ignite spontaneously. Slacking takes place, and the heating value decreases. Those changes are accelerated by fluctuations of temperature and by circulation of air through the storage space. When such coals are exposed to the weather they lose moisture rapidly. If evaporation from the surface of a lump proceeds at a faster rate than that at which it is replaced by moisture from the interior, the rate of shrinkage at the surface is greater than that at the interior; consequently stresses are generated at the surface which cause the coal to disintegrate. Likewise, when moisture is absorbed by the air-dried surface the outside layers expand at a faster rate than the interior, which results in further break-down. As these cycles are repeated the lump may disintegrate completely. Therefore, successful storage of low-rank coals depends on control of the factors that influence change of moisture.

Jan 1, 1941

An Integrated Solid Waste Management Method for Western Macedonia, Greece

Sep 13, 2010

By Joaquim Luiz Monteiro Barros

O atendimento as normas ambientais vigentes nos diversos processos das siderúrgicas no Brasil, mais do que uma exigência legal, deve ser um compromisso da empresa com os funcionários, clientes e com a sociedade como um todo. O perfeito dimensionamento do sistema de limpeza de gases e a aplicação de filtros de mangas horizontais é, com certeza, uma alternativa eficiente para solucionar de forma adequada as particularidades e necessidades dos diversos processos siderúrgicos.

Aug 17, 2017

By William C. Cooley

Data on equipment and components which have been used in hydraulic mining experiments, tests, and operations were collected from the literature. Also data were obtained from U.S. manufacturers and suppliers of equipment which is potentially applicable and available in the U.S. for hydraulic mining. The data have been divided into 24 main categories (see the following page) and have been assembled on two-page data sheets which follow. Wherever possible, drawings or photographs are included immediately after each data sheet.

Jan 1, 1975

By Victor Caso Moreira

Neste trabalho é estudado o efeito do ferro no tamanho de grão e nas propriedades mecânicas do latão UNS C26000, também comercialmente conhecido como latão 70/30. Foram avaliados dois teores residuais: 0,0069% e 0,0592%. As amostras foram inicialmente laminadas até a espessura de 2,30 mm, submetidas a tratamento térmico de recozimento objetivando tamanho de grão de 0,030 mm. Posteriormente as amostras foram laminadas para outras três espessuras e submetidas a um novo recozimento. As amostras recozidas passaram por análise de tamanho de grão e foram submetidas a ensaios de tração, sendo obtidos resultados de limite de resistência à tração. Os comportamentos apresentados pelos materiais foram distintos entre si, sendo que o material com maior teor de ferro apresentou aumento das propriedades mecânicas em função do aumento da redução de espessura e o material com menor teor ferro apresentou redução do limite de resistência à tração. Quanto ao tamanho de grão, o material com menor teor de ferro apresentou pequena variação de tamanho de grão após o recozimento, enquanto o material com maior teor de ferro apresentou redução do tamanho de grão em função do aumento da redução de espessura, demonstrando inibição do crescimento de grão e estrutura heterogênea.

Aug 17, 2017

By P R. L Browne

Study of geothermal systems in the Taupo Volcanic Zone (TVZ) has significantly advanced our understanding of the processes of epithermal mineralisation. The three main lessons learnt are: 1. knowledge of their chemical anatomy; 2. precious metal transport and deposition; and 3. hydrothermal alteration zoning. These are described in the context of ore formation and exploration.

Jan 1, 1997

By Tatiana Salviano Gadelha

Rejeitos de mineração descartados na forma de polpa possuem, geralmente, grande quantidade de água e reutilizá-la no processo, por meio de operações de desaguamento mais eficientes é de grande importância para a implementação de projetos de menor impacto ambiental. O presente trabalho visa estudar as operações envolvidas no desaguamento de um rejeito de níquel, com o objetivo de principalmente a maximizar a recuperação de água de processo. Para tanto, foram avaliados: a influência da concentração de sólidos, uso e dosagem de floculante, pressão no filtro, o processo de filtração com e sem prensagem e a influência destas variáveis na umidade da torta e na recuperação de água. Os resultados mostraram que quanto maior a dosagem de floculante menor é a recuperação de água na filtragem; por outro lado, quanto maiores a concentração de sólidos e a pressão, maior a recuperação de água. Verificou-se a importância do uso da prensagem para maximizar a recuperação da água contida no sedimento, sendo possível comprovar que o rejeito de níquel floculado e filtrado com ?P de 6 bar com o uso de prensagem promoveu a recuperação de até 77% de água.

Aug 17, 2017

By P. Trudel, É. Cabot, L. Cabot

"A modular gold processing unit (MGPU) was designed, installed and operated over an eight-month period by RSW-Béroma at the Granada mine located near Rouyn-Noranda, Quebec. A description of the project geology, plant set up, as well as exploitation results, including productivity and profitability curves, are given for a small-scale mining operation in comparison with larger ones. IntroductionSmall-scale mining (SSM) is a widespread activity in Africa, Mexico, Central America and South America, where numerous small mineral deposits are exploited manually or by semimechanized methods. On the other hand, SSM is almost absent in Canada, where the mining industry traditionally exploits large deposits, using concentration plants with capacities of many thousands of tonnes per day. However, many small gold (and other metallic or industrial mineral) deposits are known in Canada. Their reserves are too small to justify the cost related to the construction of a standard mill and, if they are remote from a custom milling facility, they remain unexploited. With this in mind, RSW-Béroma has developed the modular gold processing unit (MGPU) that allows the profitable exploitation of small mineral deposits. The MGPU is the perfect tool for SSM and its main advantages are a much lower capital cost than a standard mill and its portability, which makes it easy to transport and reinstall on another site, once the exploitation of a small deposit is terminated. The denomination MGPU will be used hereafter in the text as it was primarily designed for gold deposits, although it must be kept in mind that this portable plant can be adapted to other mineral substances."

Jan 1, 2003

By C A. Locke, A B. Christie, J Cassidy, J L. Mauk

New and existing gravity and aeromagnetic data are used to determine the structure of the Waihi region and to investigate any relationship between structure, hydrothermal alteration and epithermal mineralisation. The 24 mGal, 10 km diameter, negative Bouguer gravity anomaly which occurs south of Waihi has been modelled as a I.5 km deep asymmetrical basin. This basin, the Waihi Depression, is interpreted to be infilled with low-density volcanic rocks of the Uretara Formation and Whitianga Group, overlying older andesites of the Waipupu Formation. To the north and west, the margins of the depression are defined by the Waihi and Mangakino Faults, which have been modelled with dips of 45 - 60¦ to the south and west respectively. The southern and eastern boundaries of the Waihi Depression are defined by smooth, shallow dipping (15 - 20¦) boundaries. The Waihi Depression is interpreted as a fault-angle depression, resulting from southeast extension in the early Pliocene. The Waihi Fault is modelled as an approximately E-W feature, located to the south of Waihi. Small 2 - 4 mGal positive Bouguer gravity anomalies occur north and west of the margins of the depression, and correlate with known areas of hydrothermal alteration and areas of low magnetic gradient.

Jan 1, 2003

By William R. Yernberg

The Cripple Creek & Victor Gold Mining Co.(CC&V) celebrated completion of a two-year, $168.5-million expansion and capital improvement program. An open house celebration was held in the historic mining town of Victor, CO on Oct. 4, 2002. Hundreds of townspeople, the press and other invited guests from the mining industry joined the employees of CC&V in the celebration. The event included mine tours, company displays and a barbecue picnic, complete with a country and western band. The Cresson Mine is located about 40 km (25miles) west of Colorado Springs, CO between the towns of Cripple Creek and Victor. The mine is the only large-scale gold mining operation in Colorado and now employs about 300 (ME, October 2001, pp.21-28). The operation is a joint venture between Anglo-Gold (Colorado) (67%), based in Greenwood Village, CO, and Golden Cycle Gold (33%), based in Colorado Springs. CC&V is managed by AngloGold North America. AngloGold North America is the U.S. subsidiary of AngloGold, the world’s second largest gold mining producer. AngloGold is based in Johannesburg, South Africa.

Jan 1, 2002

By Richard Manrique

"La implementación del proyecto de modernización de la fundición de cobre de Southern Peru Copper Corporation requiere cambiar la metodología de funcionamiento de los sopladores para la etapa de conversión. En este sentido, el presente texto señala los aspectos del Sistema de control maestro de reparto de carga implementado en la Fundición de Ilo con excelentes resultados, logrando mejorar el rendimiento de los equipos con una antigüedad de mas de 30 años e invirtiendo tan solo en nuevos controladores en una etapa ligada directamente a la línea de producción. Mantener la variable primaria presión en la red de sopladores, compartiendoóptimamente la carga entre los sopladores en la red, mientras que, se minimiza el riesgo de surge, consumo de energía y los disturbios en el arranque y el paro de sopladores individuales, el sistema deberá ser lo suficientemente flexible que no deberá de perturbarse ante la salida frecuente de los convertidores, es decir deberá de mantener las presiones y flujos a la descarga del manifold ante las variaciones en el consumo de aire todo esto con un mínimo de venteos al ambiente."

Sep 19, 2006

By Hugo Leandro Rosa

A CBMM aplicou aços micro ligados ao nióbio em dois tipos de caçambas de carregadeiras de rodas que operam na usina de Araxá, Brasil. O objetivo foi avaliar os benefícios destes aços relacionados com redução dos custos, aumento da produtividade e vida útil dos componentes. Uma das máquinas analisadas coleta peças quentes de ferro nióbio para carregamento dos silos do britador. O uso de um aço ferramenta de alta resistência e resistente ao desgaste solucionou os problemas de deformação, desgaste e rachaduras durante o serviço, aumentando a vida útil da caçamba em cerca de 190%. A outra máquina avaliada foi uma carregadeira de rodas que opera na mina de minério de nióbio. O novo desenho com aços de alta resistência mecânica e resistente ao desgaste reduziu o peso em 14%, correspondendo ao incremento na capacidade de carga. A carga extra possibilitou um aumento na produtividade dos caminhões de 42 toneladas. Com os novos materiais, as trincas anteriormente encontradas na caçamba da pá carregadeira foram eliminadas, enquanto foi mantida a resistência ao desgaste antes oferecida pelo aço revestido com carbeto de cromo reduzindo também os custos de investimento em 7%.

Aug 17, 2017

By Leandro Miranda Nascimento

A maior parte da produção mundial de aço passa pela conversão de minério de ferro em grandes altos-fornos, tendo o coque como uma das matérias-primas. Por um lado, boas propriedades mecânicas a quente do coque, como o CSR e CRI, são necessárias para que o consumo de coque seja o mínimo, pois é também, junto com os óxidos de ferro, um dos maiores componentes dos custos variáveis do ferro gusa. As misturas dos vários tipos de carvões minerais utilizados exigem a participação de uma fração Hard, a mais cara e com maior poder de coqueificação, e de uma fração Soft, mais barata e inerte. Logo, quanto maior for a participação do Hard mais caro será a mistura a ser coqueificada. Uma maneira de aumentar a fração de Soft na mistura de carvões, reduzindo o custo da mistura, e ainda assim obter um coque com boa qualidade é aumentar a densidade a granel da mistura. Para isso alguns métodos já são empregados com sucesso, como o Stamp Charging e a Briquetagem Parcial. Este artigo apresenta um novo método, que consiste na densificação da mistura de carvões dentro do forno via dispositivos de vibração. Foram realizadas simulações físicas a frio e em escala reduzida para avaliar o potencial de aumento de densidade a granel da técnica. Os resultados mostram um ganho de aumento de 30% da densidade a granel da mistura.

Aug 17, 2017

By Philip J. Daynes

As part of the regeneration of the centre of Dublin, a multi-functional development is being constructed on the site of the historic Smithfield Fruit Market. The site is being developed in three phases, and includes one of the deepest basements (10m) constructed in Ireland to date. Until the recent improved economic climate, there has been little requirement for deep basements in Dublin, and this is the first to be constructed entirely within fluvio-glacial gravels and boulders. The difficult ground conditions led to the adoption of a diaphragm wall solution to ensure a watertight construction. Tie-back anchorages are utilised in the temporary case, and the wall is propped by floor slabs in the permanent case. Where required by high bedrock levels, the diaphragm wall is dowelled into limestone bedrock to ensure toe stability. The recorded lateral movement of the wall is significantly below that calculated by numerical analysis. Temporary bentonite cut-off walls were installed to divide the site into discrete sections. The basement was constructed as a tanked structure, and is subject to uplift water pressure. Passive tension minipiles provides an innovative alternative to the standard stressed anchorage solution. This paper describes:- design and construction aspects of the diaphragm wall, tie-back anchorages, and anti-flotation minipiles, together with recorded lateral wall movements,

Jan 1, 2003

By Giancarlo Alfonso Lovón Canchumani

A indústria da mineração do ferro brasileira ocupa posição relevante no cenário mundial, exportando para os principais mercados consumidores os produtos beneficiados. Esta indústria de beneficiamento tem consumo elevado de recursos e de energia, o que consequentemente gera grandes quantidades de emissões gasosas, líquidas e sólidas, contaminantes do meio ambiente. Nesse contexto o presente artigo tem por objetivo avaliar o ciclo de vida da produção de pelotas de minério de ferro, através da identificação dos impactos ambientais gerados nas etapas de lavra, beneficiamento, transporte e pelotização, com o intuito de dar subsídios a medidas mitigadoras. Foi realizado um estudo de caso em uma empresa de produção de pelotas de minério de ferro e utilizando a metodologia de Avaliação do Ciclo de Vida, baseado na norma ISO 14040. De acordo com os resultados obtidos os impactos ambientais mais importantes em relação ao ciclo de vida da produção de pelota, são referentes à categoria de depleção dos recursos minerais com 64,4% do total ponderado e a emissão de particulados no processo de lavra, que monta a 28,6% do mesmo total. Enquanto a fase com maior contribuição para o impacto total para a produção da pelota é a de beneficiamento.

Aug 16, 2017

By Gerald V. Gibbs

Quadratic functions, Q(hkl), are given to six places in increments of 0.01° for 2? from 0° to 90° for CuKa and from 25° to 180° for CuKa1. The wavelengths used for Cu in the computation are those agreed upon by the Editorial Commission of the International Tables for X-ray Crystallography (1950): CuKal 1.54051 A.; CuKa2 1.54433 A. INTRODUCTION At the Federal Bureau of Mines laboratory, Norris, Tenn., X-ray diffraction crystallography using tubes with copper targets revealed a need for a handy reference for the quadratic functions of copper radiation. The tables presented here were prepared to satisfy that need. The quadratic form Q(hkl) may be expressed in terms of the Bragg diffraction angle 2? and of the wavelength ? as

Jan 1, 1961

By C. S. Parsons

Introduction Up to the present, the operation of small mills for the treatment of gold ores has not been favoured in Canada to the extent that it has in other countries. For instance, a list of the operating properties in Southern Rhodesia, published in The Rhodesian Mining Journal of November, 1934, shows for the month of September, 1934, that there were over 500 small mills treating less than 50 tons per day, and the majority of these between 5 and 25 tons. They are operated by individuals, syndicates, and small mining companies. It is presumed that the operations are profitable, although from the published figures of the tonnages treated and the yields, it is difficult for one familiar with Canadian operations to understand how this can be possible, in the majority of cases. Most of these small mills employ stamps with plate amalgamation and with, occasionally, tables to produce a concentrate. Enquiries have been received from many parts of the world respecting milling practice suitable for small gold mines and the type of plant used in Canada. The tenor of these enquiries leaves the impression that the majority of the writers assume that the practice would be similar at all small properties. This, of course, is not the case. Conditions vary widely, and what would be a suitable mill for a typical Nova Scotia ore would not necessarily be wholly adaptable to many ores in Ontario, Quebec, or British Columbia. This paper has been written with the intention of inviting discussion, and it is hoped that, by such discussion, the subject will be more fully dealt with than has been possible in the time at the disposal of the writer. Only more or less standard principles and practices have been dealt with, and, purposely, no reference has been made to plants using mills of the Hadsel, the Nutt, or the Gibson type. As there is available but little reliable information on the costs of installation and operation of small mills, it is also hoped that those contributing to the discussion of milling practices for small mines will be in a position to give these data for the benefit of those contemplating the erection of small plants in Canada. Although it is difficult to generalize, it can be said that there are three types of gold mills commonly used at small mines: (1) Amalgamation and Gravity Concentration; (2) Amalgamation and Flotation; and (3) Cyanidation.

Jan 1, 1935

By David L. Borusiewicz, M. Suri Surendra

"Abstract Helical piles have been used as anchors and for supporting lightly loaded structures as a method of underpinning, etc in the past. Recently, helical piles are being used to support new structures because of their simple installation process using relatively light and mobile equipment. This paper presents the results of evaluation and design performed for the temporary support of existing piers during a bridge rehabilitation project.INTRODUCTIONThe helical screw foundation was invented and patented by Alexander Mitchell in England in 1833. He installed screw piles to support lighthouses in the tidal basins of England. Many applications in the earlier years in the USA were in North Carolina and in Florida to support lighthouses (in coastal plain deposits). A lighthouse of similar foundation design is still in use at Key Biscayne, Florida.In the USA, the helical piles were reintroduced as foundation elements for electrical transmission towers. Helical piles were also used for anchoring guys of self supported towers and as tie-backs for excavation support systems. Typically, helical piles are being used for supporting lightly loaded buildings and for underpinning buildings undergoing distress as a means of remediation. The helical piles are not commonly used in the transportation industry.HELICAL PILESHelical pile is a segmented deep foundation system with helical bearing plates welded to a central steel shaft. Load is transferred from the shaft to the soil through these bearing plates. Central steel shafts are available in either a square shaft (Type SS) or a round shaft (Type RS). The Type SS series are available in 38 mm to 57 mm square sizes. The Type RS series are available in 73 mm to 114 mm diameter sizes. Type SS-RS combinations are also available for compression applications in soil conditions where dense/hard soils must be penetrated with softer/loose soils above the bearing strata.The leading segment consists of a shaft with one or more helical plates that are welded to the shaft. The plates vary in diameter from 203 mm to 355.5 mm and have a thickness of 9.5 mm or 13.7 mm. Typically the plate diameter increases from the bottom of the shaft upward. A helical bearing plate or helix is one pitch of a screw thread. All helices, regardless of their diameter, have a standard 76 mm pitch. Being a true helical shape, the helices do not auger into the soil but rather screw into it with minimal soil disturbance. Helical plates are generally spaced a distance of two to three times the diameter of the plate directly below in order for them to function independently as individual bearing elements. A typical detail of helical pile is shown on Figure 1."

Jan 1, 2014