Search Documents

By U. Weber

The effect of grinding media performance on milling and operational behaviour was demonstrated under different selected conditions of calcium carbonate slurry milling. A variety of grinding media materials and bead sizes, along with two different stirrer tip speeds, were used in the grinding process to generate a particle size reduction of the calcium carbonate (CaCO3). To determine the optimum milling parameters the collected test data were used to calculate and evaluate specific energy as well as stress intensity under different milling conditions. Keywords: Grinding, mill media, high energy mills, industrial minerals, precious metals.

Jan 1, 2010

By M. Kumaran, A. Vetriselvan, A. Purantharan

"This paper presents a case history of evaluating the stability of a distressed earth bund and rectification measures carried out. A 5.45 km long, 7m high earth bund for drinking water storage was constructed in Andhra Pradesh. During construction of the bund following were observed – (a) a longitudinal crack at the downstream side (b) Bund on the downstream side along the crack settled to a max of 700 mm and (c) downstream rock toe level area raised by heave up to 175 mm. Investigation of the events made important contributions to the fundamental understanding of the behaviour of large earthworks of this type. It was found that the variation in subsoil strata was not addressed during the execution.After careful evaluation, stone columns were recommended as a suitable ground improvement technique. Stone columns were used as a reinforcement to improve the shearing resistance of foundation and in turn ensure stability. By using and applying advanced geotechnical engineering analysis tools and modelling techniques, earth bund and its foundation was analysed and examined against failure by slope instability. Stone column design was carried out using in-house computer program GEOSTONECOL and stability of earth bund was analysed using TALREN software. Earth bund construction was completed after ground improvement and is performing satisfactorily.INTRODUCTIONIn order to supply water during summer season, Government of Andhra Pradesh decided to construct a 7m high and 5.45km long earth bund summer storage tank. It was one of the largest earth bund summer storage tanks in whole of South India at the time of its construction. During construction, the earth bund has undergone sudden distresses. Investigation of the series of events occurred during construction has made important contributions to the fundamental understanding of the behaviour of large earthworks of this type. This paper presents the reasons for earth bund failure, slope stability assessment of the distressed earth bund and recommendation of stone column as a suitable ground improvement remediation technique.DESCRIPTION OF STUDY SITEThe characteristics of the original construction are briefly described as follows. A shallow cut-off trench was excavated below existing ground level at the centreline of bund as shown in Fig. 1. Below the base of the trench a cut-off grout curtain was installed. Upstream and downstream shell earth filling was carried out using Clayey Sand ‘SC’ type soil. At some locations, bottom of cut-off trench has reached as deep as 12m from the existing ground level."

Jan 1, 2017

By Ronald P. Hollenbeck

Shales in the Appalachian Region of Kentucky and Tennessee were sampled and tested to determine their use as raw materials for the manufacture of lightweight aggregate by the rotary-kiln method. Nine samples were obtained from eastern Kentucky and 143 samples were obtained from eastern Tennessee. As a result of preliminary testing of these samples, two sources in eastern Kentucky and 11 sources in eastern Tennessee were resampled for rotary-kiln tests. The rotary-kiln tests showed the two sources in Kentucky and seven sources in Tennessee contained shale that would produce satisfactory aggregate. Lightweight aggregate processed from these nine sources was tested in concrete shapes and was found to be suitable for use in structural concrete.

Jan 1, 1968

By V. Bari?ic

The scheduled power cuts of early 2008 were a disturbing reminder that South Africa needs to expand its power-generating capacity. Low-grade and discard coals, of which South Africa has much, are a source of energy and amenable to combustion in circulating fluidized beds (CFBs). Foster Wheeler (FW) has a long record in developing this technology in boilers. The technology is flexible in burning a variety of fuels; low-grade, high-ash coals, good quality bituminous and anthracite coals, and biomass and waste fuels have all been used. CFB boilers are efficient, reliable and can be designed to meet tight emission standards. In recent years once-through supercritical (OTSC) CFB technology has been developed. It enables the next stage in CFB development to proceed to a medium-scale (500 MWe) utility in such projects as Lagisza, which runs at a net efficiency of nearly 44%. Scaling the technology up to 800 MWe with a net efficiency of>45% is planned to be commercial during 2009. CFB technology can reduce CO2 emissions in the repowering of coal-fired and greenfield power plants. It does so through greater efficiencies and by co-combusting coal with biomass. FW has also developed CFB technology for the gasification of biomass, as, for example, in a pressurized gasifier to produce syngas, which can be used for the production of biodiesel, thereby reducing CO2 emissions from vehicles. Carbon capture and storage (CCS) can potentially cut CO2 emissions in the generation of power from fossil fuels in the short term, provided that it gains public acceptance, that the required regulatory framework is created, and that emission-trading mechanisms or other incentives provide a solid return on the major investments required. Oxyfuel combustion is an option in CCS; Foster Wheeler is adapting its CFB combustion technology for oxy-fuel combustion to meet this challenge. It is developing Flexi-burn?, which enables a plant to be operated either with or without carbon capture. This paper describes the status of CFB technology in terms of boiler efficiency and fuel flexibility. It highlights the advantages of CFB technology for oxyfuel combustion, presents a development plan for Flexi-burn?, and discusses a pressurized gasifier for biodiesel applications.

Jan 1, 2009

The Bureau of Mines studied available information on the nature and occurrence of potential sources of aluminum in the United States, its Pacific island possessions, and Puerto Rico to obtain data for use in evaluating the production capability and costs of extracting the aluminum from such materials. The quantity, type, and grade of the materials range from 4 billion tons of bauxite, bauxitic clay, and kaolin averaging 33 to 42 percent Al2O3 to nearly 600 billion tons of anorthosite containing only 27 percent Al2O3. Principal deposits of bauxite, bauxitic clay, and kaolin occur in Arkansas, Georgia, Hawaii, and Oregon. Major anorthosite deposits are located in New York, Wyoming, California, Idaho, and Montana. About 11 billion tons of material in deposits of various types of clay, the kyanite group of minerals, laterites, and shales averaging 27 to 30 percent Al2O3 comprise additional resource's from which aluminum some day may be extracted. Material meeting specifications of the study was found in only 22 States and the Pacific island possessions. Utilization of these large low-grade sources of aluminum awaits development of processes that are economically competitive with the Bayer process for extracting alumina from baxuite, which is at present the only commercial ore of aluminum. Changes in economic and political conditions also may play important roles in the eventual development of the potential sources of aluminum.

Jan 1, 1967

By R. Larry Grayson, Ahmet Unal

Use of radio frequency identification (RFID) technology to solve informational needs in isolated and restricted underground mining environments will be reviewed, giving specifications of some past and currently available systems. The advantages and disadvantages of using various frequencies, system configurations, and specific components, including their construction standards and capability, will be discussed. The remaining challenges to more widespread use of RFID systems for personnel and vehicle tracking will be identified, and recommendations concerning operating environment capabilities will be detailed. Finally, the ultimate requirements for maintaining system integrity during and following a coal mine emergency will be discussed.

Feb 24, 1997

Ledcap Pty Ltd has developed two software tools for assisting in the determination of life-of-mine (LOM) trucking requirements. The first tool generates haul paths and the second calculates truck travel time over these paths. The two step approach allows the paths to be viewed and if required edited, to better represent the actual site haul routes.The first tool automatically creates haul paths between the mine bench and the dump. To do this the user supplies a master haul route and a scheduled block model. The master haul path and the block model are interacted to create multiple haul routes, one for each pit/dump bench pair in each scheduling period. Each path carries with it a record of the scheduling period it represents and the dry tonnage hauled over the path in that period.The second tool calculates truck travel time over the path. Data from the manufacturer's rimpull and retarder curves are used to calculate accelerations and speed over each segment of the haul path. As the paths are derived from digitised representations of mine haul routes the path f les often have over a hundred segments. This detailed representation of the haul route allows the software to automatically adjust speed for different radius corners and accurately simulates the changing accelerations over the gradient changes that occur in real life mine ramps. Rolling resistance can be specified at a global level, at a segment level and at a period level. This allows rolling resistance to be changed seasonally as well as spatially.Life-of-mine trucking studies attempt to calculate an accurate answer from extremely variable inputs. This paper will detail the features of the two software tools and how the tools provided in the software can assist the mine planner to have greater confidence in their life-of-mine trucking requirements and the subsequent production capacity inputs to their scheduling calculations.

Dec 6, 2010

By Clarence Karr

THE BUREAU OF MINES is investigating methods for upgrading tar produced by the low-temperature carbonization of bituminous coal. This survey was undertaken to compile information needed for identifying the ether constituents of low-temperature tar. Physical properties are listed for 1,024 aromatic ethers. The compounds include cyclic and noncyclic, polyfunctional and monofunctional ethers with oxygen joined directly to either one or two aromatic rings. Alkyl groups up through butyl are included. The compounds are divided into 37 groups ranging in complexity from alkoxybenzenes to dibenzopyrans. Compounds containing aromatic ether groups are important constituents of the neutral oxygen components of low-temperature tar. For example, at Morgantown, W. Va., the Bureau of Mines has identified and determined the amounts of benzofuran, 2-, 3-, 5-, 6-, and 7 -methylbenzofuran, diphenyl ether, dibenzofuran, 2,3-dimethyldibenzofuran, and two other dimethyl-dibenzofurans in the neutral oil from a low-temperature bituminous coal tar (103, 104).3

Jan 1, 1962

By H. M. Lawrence, E. Roca

"INTRODUCTION Of the phosphate rock deposits of the United States that are being exploited actively at present, the land-pebble area in Florida is the largest producer. In recent years the land-pebble district, in Polk and Hillsborough Counties, has produced about 80 per cent of the raw phosphate rock that has supplied the requirements of the several national industries based on this essential commodity.In the land-pebble deposits sizes finer than 16 to 22 mesh are below the commercial limit in phosphate content, and washing-plant practice has been directed to the recovery of the coarser material. Recently, more extensive control of the washery plan has resulted in the saving of additional amounts of phosphate, the loss of which had been considered unavoidable. However, strict requirements of the trade regarding the lowest acceptable grade of phosphate rock prevent the inclusion of more than a very small proportion of the low-grade phosphatic sands with the washery output of phosphate roe:. Further advances in practice resulting in larger recoveries of phosphate can only be effected by the application of processes that are based on other principles than merely a difference of particle size. Research is be conducted actively along these lines by the industry and by cooperating agencies.Flotation has been studied for several years by the International Agricultural Corporation and its allied company, the Phosphate Recovery Corporation. J. T. Burrows, vice-president of the International Agricultural Corporation, in a letter dated July 10, 1929, states:"

Aug 1, 1931

By Kevin W. Cargill

In September 2004, Hurricanes Frances and Ivan caused the Pigeon River in western North Carolina to flood. This flooding eroded the embankment below Interstate 40 (I-40) and sent one of the eastbound lanes, along with the roadway shoulder, into the river below the embankment. North Carolina Department of Transportation (NCDOT) needed to reopen all the lanes of I-40 as soon as possible and considered this damage to be an emergency situation. NCDOT contracted Schnabel Foundation Company to design and build a repair that would keep this important interstate open and reestablish the eastbound lane. The obstacles included limited work room, the requirement of keeping the remaining lanes of I-40 in service, and producing a final product that would be relatively maintenance free and last at least 100 years. The proposed repair had to consider that the existing interstate was founded on a rock fill that was constructed from rock blasted off the adjacent mountain side. The selected design included two, tied-back micropile walls to address these obstacles and other issues. Each of the walls were constructed of 10.75 inch diameter micropiles and corrosion-protected tieback anchors installed through the existing rock fill into competent bedrock, concrete wales, and a reinforced shotcrete facing. This successful project was completed during the coldest months of the year and within the timeframe established by the State of North Carolina. This paper will discuss the design and construction of the repair and the many challenges that had to be overcome.

Jan 1, 2006

By Naj Aziz

The shear behaviour of reinforced rock joints is investigated for the bolt-grout-rock interaction and for failure mechanism. The effectiveness of the bolt application under lateral and axial loading conditions within surrounding materials is investigated in different medium strength. Double shearing testing of bolts were studied in concrete blocks of 20, 40, 50 and 100 MPa strengths, subjected to different pretension loads of 0, 5, 10, 20, 50 and 80 KN respectively. The experimental study was complemented with three-dimensional numerical analysis. Parameters examined include: shear resistance, shear displacement, induced strains and stresses during bolt bending process and its ultimate failure across the sheared joint planes. The conclusions drawn from the study were; the level of bolt resistance to shearing was influenced by the bolt profile configuration, the strength of the rock or medium influenced the level of load generated on the bolt, and the increase in bolt pretension has contributed to the increased shearing load of the bolted medium.

Jan 1, 2007

By Fiseha Tesfaye, Pekka Taskinen

"A thermodynamic study of the equilibrium phase assemblage AgBi3S5-Bi2S3-S was made by an EMF-technique, using the RbAg4l5 solid electrolyte. The ternary phase was synthesized from the pure Ag2S and Bi2S3 in an evacuated silica ampoule and grinded into powder and mixed with appropriate compositions of B12S3 and S, in a series of experiments, for pressing in to pellets. The pellets were assembled to form the galvanic cells Pt (-) | Ag ] RbAg4ls | AgBi3S5+ Bi2S3 + S + (C) I Pt (+). The EMF-measurements were made in the temperature range 299 - 460 K.In this paper, thermodynamic functions of the ternary phase AgBi3S5 (pavonite) have been determined. The agreement between the obtained results and the literature values were established.IntroductionThe complex group of ore minerals constitutes from trace amounts to a major proportions of sulfosalts. Although the sulfosalts rarely form massive ore bodies, they are commonly associated with rich sulfide ore minerals for the base and precious metals and widely distributed in a metal poor sulfide minerals [1]. For instance, Ag-bearing sulfosalts are encountered in ore minerals for the production of the base metals and are common sources of silver. Nevertheless, thermodynamic properties of the sulfosalts are poorly known.Reliable thermochemical data are essential for quantitative modeling of the chemical behavior of the sulfosalts in equilibrium with sulfides, which in turn would promote the optimization of complex minerals treatment and extractive metallurgy of the valuable metals."

Jan 1, 2012

By Rodrigo Toro, Ivan Yutronic N

"The Copper Concentrator Plant of Compañía Minera Doña Inés de Collahuasi (CMDIC) is composed of three grinding lines, the third one being the largest. Due to the capacity feature of the third line, specially its SAG mill, it is a priority that the advanced process control team of the Company deploys a supervisory control strategy that allows this unit to operate in an optimal way, in order to achieve the maximum productivity at minimum cost. It is in this kind of tasks where advanced control applications play a key role in obtaining the best economic profit of the process.The advanced process control team, formed by people from Informatics, Automation and Operations of CMDIC have assumed the challenge of generating the transition from a manual SAG Mill 1011 operation (40 x 22 feet, the largest copper SAG mill of the world), to a fully automatic SAG Mill using a multivariable control strategy instead of a rule based on expert control system (widely used in industrial mining process control applications).Therefore, CMDIC decided to work together with Honeywell APC Team implementing an advanced automatic control strategy for the SAG Mill 1011, using for this purpose a technology called Model Based Predictive Control (MPC), based on a variety of control methods that uses dynamical models of the process, obtained from input/output data, in order to print the process knowledge into a group of mathematical relationships that links the constraints (controlled variables) with available commands (manipulated variables) and measured disturbances.The main objective of the advanced control strategy is to ensure process government, tending to throughput stability and optimization, by the execution of coordinated control actions, proactively avoiding measured disturbances effects and the SAG mill overloading.The most important benefits of using a multivariable control strategy are: the automated operation of SAG mill 1011 (that was manually operated before the implementation of this application), a safer, more coordinated and more stable process operation, achieving through this an increase of throughput and a decrease of specific energy consumption, controlling the amount of oversize material production, power consumption, mill loading, noise and torque. In addition to the operational results, this challenge has consolidated a control team, with the participation of engineers and operators, diminishing the typical implementation time and achieving a greater use of the application in a short time."

Jan 1, 2010

This Bureau of Mines report describes research on methods of assuring the continued safety of mine electrical power distribution circuits through reliability and quality assessment of the protective devices, innovative inspection techniques for these devices and the circuits themselves, novel applications of trolley line circuit breakers, and computer modeling of distribution systems to determine the proper ratings for cables, power sources, and circuit protective elements. Battery charger safety is included.

Jan 1, 1979

By Gregg Davidson, Lonnie Jacobs, Brett Zernich, Alan Howard, Robert Pintabona

All Rights Reserved. Printed in the United States of America. Information contained in this work has been obtained by SME, Inc. from sources believed to be reliable. However, neither SME nor its authors guarantee the accuracy or completeness of any information published herein, and neither SME nor its authors shall be responsible for any errors, omissions, or damages arising out of use of this information. This work is published with the understanding that SME and its authors are supplying information but are not attempting to render engineering or other professional services. If such services are required, the assistance of an appropriate professional should be sought. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of the publisher. Any statement or views presented here are those of the authors and are not necessarily those of SME. The mention of trade names for commercial products does not imply the approval or endorsement of SME.

Dec 1, 2014

The development and introduction of a preventive maintenance scheme in the coke ovens department, coal preparation section, of The Broken Hill Proprietary Co. Ltd., Newcastle steelworks, is described together with its operation and the results achieved during the first 12 months.'fhe scheme consists essentially of an engineering analysis of the plant to establish maintenance schedules, and to record the details on reference cards.Items are reviewed progressively and a weekly work schedule is prepared, from which work orders are passed on to the maintenance foremen. These foremen in turn originate action orders and issue inspection sheets as required. Results are then reported back to the maintenance planner and used to revise norms, practices, and cycles.INTRODUCTIONWhat is maintenance? Some people consider maintenance to be the work involved in putting things together again after they have fallen apart. The author regards it as the mechanical care and repair of plant machinery and equipment to keep it operating in sound mechanical condition, without undue interference with production processes.Maintenance may be organized or haphazard, and, too often, what has been fondly imagined to be nicely controlled and organized maintenance proves, under pressure, to be more correctly described as haphazard. Haphazard maintenance deals with breakdowns as they occur, and frequently finds itself confronted with more breakdowns than can be handled. Even organized maintenance, if not based on sound planning, can, at times, be found in a chaotic state, because of unexpected and unanticipated breakdown.Properly planned and scheduled maintenance permits an orderly and controlled approach to the problem of maintain...

Jan 1, 1961

By A. C. Fieldner

"Decline of the Beehive Coke OvenTwenty years ago a favorite theme of the crusader for fuel conservation was the enormous waste of valuable by-products incurred in the manufacture of blast-furnace coke in beehive ovens. Indeed, there was good reason for arousing the national conscience to this needless' loss of an irreplaceable mineral resource. In 1910, 83 per cent of the coke production was made in beehive ovens, from which surplus gas, tar, light oil, and ammonia, aggregating in value (at 1910 prices) 40 million dollars annually, were discharged into the atmosphere.In 1929, proportions were reversed and 90 per cent of the production was made in by-product ovens. The average value of by-products obtained in the production of 1 ton of coke in 1929 was $3.60, as compared with $1.16 in 1910, although the value of a ton of coke had increased only from $3.47 to $4.80. As shown in Figure 1,1 the production of by-product coke progressed rather slowly until 1915. War needs suddenly expanded the demand for coke and the by-products benzol and toluol for the manufacture of explosives. Except during the depression of 1921, this accelerating rate of production was maintained up to 1929, largely at the expense of beehive plants. The 1929 production of 60 million tons of coke will probably remain a record-breaking figure for several years. The developments which are now in progress in long-distance transmission of rural gas and in the utilization of volatile petroleum products and refinery gases for augmenting, city gas supplies may retard an other- wise accelerating demand for coke and coke-oven gas for domestic and industrial heating, Trends in Value of By-ProductsThe increasing value of by-products in comparison to the value of coke is shown in Figure 2. In 1913, the average value of by-product coke was $3.38, the value of the by-products per ton of coke was $1.41, and the cost of coal per ton of coke was $3,27, In 1929 not shown in figure) the value of the coke had risen to $4.80 per ton, the value of the by-products to $3.60, and the cost of coal per ton of coke to $5.07. The by-product values in were 155 per cent higher than in 1913, although the coke value had increased only 25 per And the cost of the coal 55 per cent. Actually the increase or the total value of coke plus by-products in this period was very little more than the increase in the coat of the coal, being 55per cent for coal and 60 per cent for coke plus by-products."

Mar 1, 1931

By R. P. Sloan, A. S. Whitford

In November 1999, CCI's Empire Iron Mining Partnership and MinnovEX Technologies Inc. developed an expert system for advanced control of their Empire IV Grinding Section. Empire IV is comprised of three autogenous Primary Mills and six autogenous Pebble Mills, with a single Pebble Crusher and high pressure Roll Press. The challenges of controlling and optimizing three distinct grinding lines that are inter-woven by a pebble crushing circuit were met with innovative and unique solutions. This paper will detail the approach employed at Empire and will focus on the aspects that make this application unique.

Jan 1, 2001

By H. Venkatesh, Balachander R.

This article discusses the method that was adopted for controlling damage to rock mass while excavating an underground powerhouse cavern at Tala Hydroelectric Project. It discusses in detail the near field vibration studies carried out and the safe vibration levels established for that rock mass condition.

Jan 1, 2006

By Erich J. Jacob

In the past 15 years the enforced improvement of the public traffic systems caused a boom in urban tunnel construction. In 1961 the City of Paris started to build the Express-Metro. Of the 47 km long double-track line crossing the city center, nearly 45 km are in operation since 1971. Still missing is here only an about 2.6 km long connecting stretch, which is under construction now. From 1963 to 1969 the 21.8 km long Victoria Line was built in London as extension of the existing network,. A little later, in the years 1965 to 1973, the City of Hamburg supplemented its subway network by the construction of a 16.8 km long line between the Boroughs of Billstedt and Stellingen. Also in 1965 the City o Munich started to build a subway system of 54 km f length. Thereof a stretch of 16.2 km could be taken into operation in 1972 shortly before the Olympic Games. These are only some of the better known projectsas examples of the activities in European cities. In nearly all cities with more than about ½ million inhabitants subsurface traffic lines were begun or supplemented. Furthermore, numerous undercuts or other subsurface structures were built. The Ij Tunnel in Amsterdam and the new Elbe Tunnel in Hamburg may be mentioned, both structures finding international attention.

Jan 1, 1976