Search Documents

By D. J. Dollhopf

The objective of this five year study was to investigate the means of establishing non-polluted ground-water and root zone systems in areas where surface mining intercepts physiochemically unsuitable overburden materials. Overburden may need to be sampled on a 60 m grid in order to delineate materials unsuitable for reclamation and to accurately implement selective handling operations. Unsuitable overburden materials were buried successfully in a dragline operation with a minimum of delays, but costs were increased 12 to 53%. After three years the buried material remains above the reestablished aquifer and below the root zone. Construction of a clay cap over the buried material may not be required in semiarid environments. It was shown that some unsuitable overburden materials do not have to be special handled. When inhibitory material constituted <5% of the total overburden volume, such material was essentially not detectable in the resultant spoil pile due to mixing/dilution processes. When inhibitory material exceeded 15% of the overburden volume it was always found in the resultant spoil pile, generally with a smaller extent, indicating partial dilution. At least a portion of the postmine aquifer had hydraulic conductivity rates lower than the premine system, indicating the reestablished aquifer may, in part, conduct ground water very slowly. Postmine ground-water chemical quality in spoil materials had poorer quality compared to premine ground water.

Jan 1, 1981

1. Book reviews A report by the Monopolies and Mergers Commission on the efficiency and. costs in the development, production and supply of coal by the NCB (Chairman G. Le Quesne). London, Her Majesty&apos;s Stationery Office, Jun. 1983. £20 for report and appendices (2 vols). Reviewer: M. J. Martinson Canadian mines handbook 1983-84, edited by M. R. Brown. Toronto, Northern Miner Press Ltd, 1983. 444 pp. $22. Reviewer: Northern Miner Review Editor 2. New publications Developments in geophysical exploration methods-5, edited by A. A. Fitch. Barking. Applied Science Publishers Ltd (Ripple Road, Barking, Essex IG II OSA, England), 1983. 255 pp. £35.75. High-pressure researches in geoscience--behaviour and properties of earth materials at high pressures and temperatures, edited by W. Schreyer. Stuttgart, E. Schweizerbart&apos;sche Verlagsbuchhandlung, 1983. 545 pp. DM 188. Dynamics of oil and gas accumulations, by Alain Perrodon. Pau, Elf Aquitaine (Documentation Centre Micoulau, 64018 Pau, France), 1983. 368 pp. 240 FF. New paths to mineral exploration, edited by F. Bender. Stuttgart, E. Schweizerbart&apos;sche Verlagsbuchhandlung, 1983. 169 pp. DM 58. Results of the First Workshop on Standards in Geothermics, edited by R. Haenel and M. Gupta. Stuttgart, E. Schweizerbart&apos;sche Verlagsbuchhandlung, 1983. DM 98. E&MJ book of jlowsheets edited by Paul C. Merritt. New York, McGraw-Hill, 1983. 214 pp. $42. 1983 E&MJ international directory of mining. New York, McGraw-Hill, 1983. 808 pp. $70. The future of heavy crude and tar sands - volume 11. New York, McGraw-Hill, 1983. 1300 pp. $1l0. 3. Mineral Policy and Energy publications Aluminium, by A. Johnston. 12 pp. . Arsenic, by J. J. Hogan. 4 pp. Cobalt, by D. G. Fong. 6 pp. Selenium and tellurium, by A. G. Johnston. 7 pp. Stone, by D. H. Stonehouse. 13 pp. Uranium, by R. T. Whillans. 16 pp. 4. Mintek publications Report M88 &apos;l&apos;he recovery of platinum-group metals and gold by the lead-collectionstep of thefire-assay procedure. Report MI04 The preparation and analysis of reference materials, and the provision of recommended values. Progress report no. 5. Report Mll1 The determination, by flow-injection analysis, of iron, sulphate, silver, and cadmium. Special publication 3 A guide to the presentation of papers.

Jan 1, 1983

By James E. Aplin

Previous studies have shown that fracturing of roof strata precedes ultimate failure, and that the fracture development causes an accompanying increase in the apparent resistivity of the strata. Using this principal, a microprocessor controlled resistivity roof fall warning system (RRFWS) was developed that automatically sequences through and records up to 32 electrodes that may serve as either voltage or current electrodes. This capability permits increased coverage with a minimal number of required electrodes. The data is stored in a nonvolatile memory and on an optional printout, making the system nonsusceptible to loss of mine-power. To further save battery power, the system&apos;s electronics shut down between readings, except for a carbon molybdenum steel real-time clock. At a preprogramed interval, the RRFWS reactivates and repeats the sequence. If the absolute change or the rate of change of resistivity exceeds a predetermined limit the system is capable of sounding an alarm. In addition to the monitor, a stainless steel mod led split-set electrode was also developed that permits long-term corrosion-free contact.

Jan 1, 1983

By Kent W. Hawley

An improved visibility system was developed for use on the large (100 ton+) haulage trucks typically operated in open pit and surface mines. The improved visibility system provides the truck driver&apos; with a means of viewing hazardous situations that occur in the extensive blind areas adjacent to his true. The cost effective, reliable, visibility system consists of a closed-circuit television three unique fresnel viewers, and two improved mirrors. This report describes the visibility problems of Large trucks in the surface mining environment, shows the performance of existing mirrors, substantiates concept selection, and describes the prototype improved visibility system.

Jan 1, 1978

By Irvin Pritts

This report describes the design, fabrication, and testing of a prototype instrument which demonstrates the feasibility of determining respirable coal dust concentrations by light reflectance photometry. Coal dust is collected on a filter and the quantity collected is continuously monitored by reflectance-photometry. Light emission and detection is accomplished by reflective object sensors, which have both light source and detector in one chip. The use of a pulsed light source insures low drift characteristics of the measuring circuitry. The collection of the respirable coal dust on filters facilitates accurate calibration and also allows measurement verification, if desired, by well-accepted, gravimetric methods.

Jan 1, 1981

By Sara Jane Boles

In recent years the interest in rare-earth compounds as refractory materials has exceeded the available literature on the subject. While some basic properties, such as density and melting point, of the more readily available rare-earth compounds have been reported in the literature, relatively few papers can be found that deal comprehensively and primarily with high-temperature refractory properties and applications of rare-earth oxides, carbides, sulfides, and nitrides. Therefore, this bibliography has been pre-pared for the use of the ceramic industry as a guide for locating and utilizing the scattered and frequently fragmentary information available. The term "rare earths", as applied in the literature search for this bibliography, is understood to include the following elements: cerium, dysprosium, erbium, europium, gadolinium, holmium, lanthanum, lutetium, neodymium, praseodymium, samarium, terbium, thorium, thulium, uranium, and ytterbium. (On the periodic chart, these elements appear as numbers 57 through 60, 62 through 71, 90, and 92.) It is emphasized that many of the abstracts included are from papers in which the rare-earth compound or compounds are treated along with several other ceramic materials, are mentioned only secondarily, with primary interest placed on a more commonly used refractory material, or are used as part of a mixture of materials formed experimentally and reported on in the paper. As the better known rare-earth materials, such as the oxides of uranium, thorium, and cerium, appear more frequently in the literature, they also appear more frequently in this collection. Articles abstracted include only information on the basic properties that are of interest to the refractories investigator. References to crystal lattices and related topics are generally excluded from this publication. The temperature 1,500° C. has been set arbitrarily as the lower limit for reported data on thermal properties. However, because of the scarcity of information, some reports are included in which data are limited to those obtained at lower temperatures. Many of the articles abstracted include lists of references that will be of additional assistance in pursuing specific lines of investigation.

Jan 1, 1962

By H. M. Lawrence

"The land-pebble district, the larger of the two producing areas of Florida, is situated in Polk County and in the eastern part of Hillsborough County. About 80 per cent at the phosphate rock produced in the United States in recent years has been mined from this area. The phosphate ores, locally termed matrix. are beds of sands and clays containing the phosphate pebbles, considered to be Pliocene in age, derived by marine action from underlying Miocene phosphatic marls, and are covered by practically barren sands and clays that have been deposited more recently. Open-pit mining is practiced; hydraulic mining, which has been intensively developed in this district, is used exclusively for mining the matrix and, by some companies for removing the overburden, although drag-line excavators have become established and are proving economical for stripping operations. From the pits the matrix is pumped to adjacent washing plants for beneficiation. The product of the washers. after drying, enters the world markets as Florida pebble phosphate.In this district recovery of the phosphate pebbles by the washing plants has not been particularly effective in the past. The screening, designed to effect a seperation at about 20 mesh (0.033 inches), has not been well controlled. Washer rejects discarded to the waste dumps have contained appreciable amounts of material analyzing above the minimum commercial grade - 66 per cent B.P.L. (bone phosphate of lime). Such losses of commercial fractions should be considered avoidable, and have been discussed at length in a previous paper.3"

Jul 1, 1930

By L. I. Rosato

A novel hydrometallurgical process for the recovery of silver and gold from neutral leach residue that is based upon leaching with thiourea, is described. Laboratory and pilot plant studies have shown that 80-90% of the silver and 60-70% of the gold can be recovered by:? ( i) leaching zinc calcine with &apos;Spent electrolyte at pH 2.0-3.0 to generate a precious metal-bearing zinc ferrite residue, (ii) leaching of the thickened zinc ferrite with 3-5 g/L thiourea in a six stage carbon-in-pulp circuit, (iii) elution of silver and gold from the loaded carbon with a thiourea- butanol solution, (iv) thermal regeneration of the stripped carbon and (v) recovery of the precious metals from the pregnant eluate by cementation with zinc dust. The reasons for adopting the thiourea CIP leach and the preferred operating parameters for each process step are presented. The requirements for the destruction of any thiourea transferred to the zinc circuit are outlined, and the results of an integrated one tonne/day pilot plant operation at Canadian Electrolytic Zinc are given.

Jan 1, 1990

By R. L. Zick, J. D. Byars, T. P. Mucho

Recently, a large Pittsburgh seam longwall mine was nearing depletion of a major portion of its current reserves and had begun to develop in a different direction from its original portal area to access additional reserves. This meant that a large area of the mine would be abandoned and sealed. However, continued use of the original mine portal area required that the water accumulating in the abandoned mine would eventually need to be pumped to the surface. This would be in addition to the discharge water associated with the new portion of the mine. Several pumping and sump options were investigated to handle the quantity and quality of the anticipated discharge water. This paper describes some of these options, their advantages and disadvantages, and the final engineering decisions. Some problems and unanticipated outcomes, as well as the eventual solutions are discussed, including: (1) estimates of pump requirements, (2) water pool size, (3) eventual water quality, (4) anticipated inflows, and (5) integration into the overall mine water system.

By R. M. G. S. Berezowsky

Treatment of Hudson Bay Mining and Smelting Co. Ltd. (HBM&S) zinc concentrate in the Sherritt zinc pressure leach process produces a residue containing elemental sulphur, residual sulphides, precipitated iron species, si1ver and gold. Flotation of the residue recovers most of the elemental sulphur and residual sulphides to the concentrate, leaving iron oxides and bask sulphates in the tailings. The tailings also contain most of the sflver and some gold. Direct cyantde leaching of the oxide tailings (220 g/t Ag, 1.4 g/t Au) was capable of leaching most of the gold, but only a minor portion of the silver. This paper reports testwork, conducted by Sherritt on behalf of HBM&S, to define a process for a high recovery of the precious metals from the oxide tailings. A si1ver enhancement treatment, consisting basically of digestion of the residue with lime at 90°C to render the silver amenable to enhanced recovery by subsequent cyanidation, was selected as the most promising approach. Batch silver enhancement and cyanidation tests showed that treatment of the oxide residue with 80 kg/t CaO at 90°C for 1 to 2 h increased the silver extractability in subsequent cyanidation from <20% to 96%. A 96 h continuous miniplant test (1 kg/h solids feed rate), of a circuit including a silver enhancement treatment step followed by conventional cyanidation and carbon in pulp silver and gold recovery, confirmed metal recoveries to the carbon of 90% Au and 96% Ag. Reagent consumption rates were 1ess than 100 ?kg/t CaO and 5 kg/t NaCN.

Jan 1, 1990

By Andrew E. Nevin

The government of India convened a precedent-setting meeting in New Delhi on Nov. 12, 2001.The meeting brought together regulators and the mining industry in an attempt to fix the industry’s mine development problems in that country. More than 150people attended the all-day session. Ram Vilas Paswan, Minister of Coal and Mines, chaired the meeting. Ravi Shankar Prasad, Minister of State for Coal and Mines, was also present. The secretary of the Department of Mines and the Joint Secretaries and Additional Secretary also participated. The Department of Mines’ mandate is for economic growth: to get new mine development going and to make investment in mining attractive for both domestic and foreign-owned companies.

Jan 1, 2002

By P. Nicholls

[This paper sets forth the burning characteristics of coke used as a domestic fuel as shown by work of the U. S. Bureau of Mines and others. Coke is a truly smokeless solid fuel and is held in high regard for this quality. Ways are being found for making commercial coke from a wider range of cools than heretofore, and tale use of coke for domestic heating is increasing. ACKNOWLEDGMENTS The experimental work reported in this paper was conducted at the Pittsburgh Experiment Station of the U. S. Bureau of Mines cinder the authority of O. P. Hood, chief mechanical engineer; M. L. Orr, assistant feels engineer, and W. M. Brewer, junior fuels engineer, assisted by Charles Schramm cooperated in making the tests.]

Jan 1, 1929

Agglomeration for Copper Heap Leaching Agglomeration of ore is a method which can be used to eliminate the migration of fine grained particles throughout a leach heap. Without agglomeration, fine ore particles are able to migration within the heap, clogging flow channels and producing large areas where access of the solution is poor. In order to gain the benefits of agglomeration and improve agglomerate strength even further in copper heap leaching, an economical, acid-resistant binder is needed. However, most binders have been used without any systematic reasoning. A set of novel testing methods were developed, including a soak test, percolation flooded columns, and larger long-term leach columns. The soak test compares the degree of breakdown when agglomerates are subjected to an acidic environment. While the percolation flooded columns and larger long-term leach columns evaluate the flow of leach solution throughout the ore bed. Systematic studies have been completed on a wide range of binders using these novel testing procedures. It was found that for a low grade chalcocite ore, which was rich in silica, from a southwest US mine, polyacrylamides reduced the fines migration the best in the novel soak test. The non-ionic binder, in particular, was found to reduce fines migration as much as 93 per cent. Several of the binders tested were shown to increase the hydraulic conductivities of the agglomerated ore up to 2.5 mm/sec, compared to a hydraulic conductivity of only 0.25 mm/sec when no binder was used. These binders also prevented &apos;slumping&apos; of the ore, which indicates a decrease in breakdown of the agglomerates. The use of a binder also showed no interference with leaching reactions in long-term leaching experiments.

Sep 13, 2010

By Tracy Brettmann, Will Bohlen

An innovative retaining wall design consisting of tangent drilled shafts with supplementary seal piles was used to limit continuing bank erosion along the Brazos River in Southeast Texas. The riverbank erosion had progressed to where it was threatening the stability of both the bridge abutment and corresponding approach embankment of the heavily travelled Highway 99 bridge at this location. A tangent pile design was selected because it was both much faster to install and more cost effective than a secant pile system. The design included both 5.5-ft and 10-ft diameter shafts with depths up to 130-ft and comprised both anchored and cantilevered sections. Supplementary seal shafts were also installed between the structural tangent drilled shafts to help plug any gaps between the tangent shafts. The plumbness and diameter of the shafts were tested using a sonic caliper to make sure the shafts were installed within the specified tolerance. The initial design had to be revised when a record flood from Hurricane Harvey impacted the site during construction. Introduction The Fort Bend Grand Parkway Toll Road Authority (Owner) needed to protect the north bridge abutment with a retaining wall system due to rapidly eroding conditions of the Brazos River banks within the 300- feet-right-of-way of the State Highway 99 Jodie Stavinoha Bridge. The extent of the local scour and erosion along the north bank of the Brazos River has caused concern for the structural integrity of the bridge. The magnitude of the erosion along the north bank at the location of the bridge has been measured at about 120 feet over three recent hydrologic flood events locally referred to as Memorial Day 2015, Memorial Day 2016, and Tax Day 2016. During construction, a new record flood level occurred due to Hurricane Harvey in August of 2017 that resulted in a portion of the retaining wall needing to be redesigned due to even more erosion occurring. The Brazos River is an actively eroding and meandering alluvial river plain that naturally meanders and migrates over time. The processes of bank erosion and meander migration were ongoing before the bridge was constructed and will continue in the future. These recurring major flood events, however, rapidly increased the rate of erosion in just a few years. Background. Due to the need to protect the bridge as soon as possible, the Owner selected a project team consisting of the designer, general contractor and specialty deep foundation contractor prior to final design to work together in developing a cost-effective design that could be implemented rapidly. The project team initially considered both a secant pile and tangent pile retaining wall system using drilled shafts. After reviewing various alternative designs, a tangent pile wall with seal piles was selected based on both cost effectiveness and speed of installation. The tangent pile with seal pile option was approximately 20 percent lower in cost and 50 percent faster to install.

Jan 1, 2018

By Daniel Hauer

In considering the cost of rock excavation, but little attention has been given to the economical handling and breaking up of boulders. Very few records seem to have been kept as to the cost of such work, and although it is difficult for this reason, to set a fair price for breaking up and handling boulders of various sizes, yet the cost of this detail work enters very materially into the cost of solid rock excavation. The subject is worthy of close and prolonged study.

Jan 1, 2006

By J. R. Ross

A reconnaissance for sources of scandium and a metallurgical investigation of recovery methods for byproduct scandium from uranium mill solutions were conducted by the Bureau of Mines. The work on scandium was undertaken to obtain information on domestic resources and to explore and develop recovery procedures in consonance with the Bureau&apos;s long-range program for conservation and wise utilization of mineral resources. The element scandium is widely distributed in the earth&apos;s crust in trace amounts, but it seldom occurs as an important constituent in any mineral. An exception is thortveitite, (Sc,Y)2 Si207) a rare mineral that contains various amounts of scandium and yttrium and may contain up to 42 percent scandium oxide (SC203). Knowledge of the chemistry of scandium has expanded rapidly in recent years (1, 4, 9)4 but only fragmentary information is available about the metal because it is still largely a laboratory curiosity without established uses (2, 3). A recent study shows some of the physical proper-ties of the metal are (1) density of 3.05 grams per cubic centimeter) (2) melting point of 1,540° C, (3) hexagonal close-packed structure) (4) hardness of about 50 Brinell (500-kilogram load), and (5) an alloy behavior similar to yttrium and rare-earth metals (2). The price of $2,850 a pound for scandium oxide of 99.9 percent purity and $2,700 a pound for oxide of 99 percent purity reflects the scarcity and complex chemistry of the element.

Jan 1, 1962

By Louis A. Panek

Using an approach based on the theory of similitude, the author develops a general equation and related concepts that provide new insights to an old problem. The load-bearing capacity (strength) of a square, rectangular, or cylindrical prism of a brittle material such as rock, coal, or concrete is expressed as the mathematical product of a size effect, a shape effect, and a function of the mechanical properties (deformability, cleat/joint spacing, and friction) of the pillar, roof and floor materials. Through an application of multivariate statistical analysis, the results of assorted tests and observations of failed pillars can be combined into a fundamental scaling equation, which provides a unified, consistent approach to the estimation of mine pillar strength. The form of the equation is sufficiently general to be able to incorporate refinements in the characterization of the basis factors, as they become available through future experimentation and analysis.

Jan 1, 1979

Provide optimum visibility of mining operations while maintaining protection and comfort for ma-chine operators. Approach Cabs and canopies with hydraulically powered variable-height control were developed for several machines and tested in underground mining operations. How It Works From his position in the cab, the operator can raise or lower the cab, selecting a height that offers either more visibility of the working place or greater clearance for tramming. The entire cab enclosure moves up and down on guide rollers that ride on a pair of rails, and is actuated by a hydraulic cylinder controlled from within the cab. Normal working heights, for each of the four different cabs developed, are with the cab bottom from 6 to 8 inches above the mine bottom. A typical range of elevation (excursion) afforded by this design is shown in Figure 1.

Jan 1, 1978

By Wayne L. Worrell

Thermodynamic data for the stable carbides and oxides of chromium, molybdenum, and tungsten have been critically eualuuted and are used to determine the stable condensed phases at 1 atm total pressure in each metal-carbon-oxygen system. Pourbaix-Ellingham diagrams have been constructed and are used to estimate the minimum temperatures neces.see)*y to oblain these metals by corbolhermic redlrction under reduced pressures. USING recently reported data for the carbides and oxides of chromium, molybdenum, and tungsten, the stable phases in the Group VI metal-carbon-oxygen systems at specific temperatures and pressures can be determined. The thermodynamically stable regions in each metal-carbon-oxygen system can be completely pictured using a Pourbaix-Ellingham diagram in which the two coordinates are oxygen potential (-RT In Po2) and temperature. Worrell and chipman&apos; have described and constructed such diagrams for the metal-carbon-oxygen systems of vanadium, columbium, and tantalum. Downing2 has used similar diagrams to provide a description of the reactions in submerged arc furnaces. One of the examples which he cited was the Cr-C-O system; however, an improved diagram is presented in this paper using recently obtained data for the carbides of chromium. Although some of the oxides and carbides of the Group VI metals exist over slight ranges of composition,3 all solid phases are represented as stoi-chiometric compounds in the subsequent diagrams. Any error introduced into the calculated equilibria by neglecting the compositional variation of these phases is less than the uncertainty in the thermodynamic data. In a Pourbaix-Ellingham diagram for a three-component system, the phase rule requires that at equilibrium four condensed phases specify a point, three condensed phases determine a line, and two condensed phases define an area. To obtain a well-defined area at high oxygen potentials and teniperatures, the initial carbon to oxygen mole ratio is specified to be more than sufficient to reduce the oxide but not enough to convert all the metal to carbide. Thus, the lowest regions in the subse- quent Pourbaix-Ellingham diagrams represent areas in which the metal and its carbide are the stable condensed phases. Cr-C-O SYSTEM A) Thermodynamic Data. To simplify the subsequent calculations, all thermodynamic data are presented in the form of linear Gibbs-energy-of-formation* equations which were derived for the temperature range 505° to 2000°K and are reasonably accurate over the entire temperature ranges of the diagrams. The thermodynamic data for the compounds occurring in the Cr-C-O system are summarized in Table I. Several volatile chromium oxides have been reported,4 but their influence is negligible in the Cr-C-O system. Thermodynamic data for CO and CO2 were taken from the compilation of Coughlin.5 The only solid chromium oxide sufficiently stable to exist below 1800°K in the Cr-C-O system is Cr2Os.11 The Gibbs-energy-of-formation equation for Cr2O3 was obtained by revising the data tabulated in Coughlin,5 using the heat of formation of ah&apos; and the high-temperature thermal data for chromium.7 In 1953 Richardson8 re-evaluated the original work of Kelley and coworkers,9 who measured the thermodynamic properties of the chromium carbides. However, the high-temperature equilibrium results of Boericke9 yield values for ?G°f of Cr2O3 which are 2 kcal more positive than the accepted data. His results for the chromium carbides are based on the same questionable equilibria. Gleiser10 recently determined the Gibbs energy of formation of Cr3C2 and the equation in Table I was calculated from her data and the thermal data of Kelley and coworkers.9 Thermodynamic data for the Cr7C3 and Cr23C6 carbides were obtained by combining the Cr3C2 data

Jan 1, 1965

By K. Lim, J. Sobil, L. Galarza Castillo, F. Tozlu

"For mining operations globally, the scale and criticality of the grinding mill drive has meant that selection of the correct mill drive technology is paramount. With so much depending on the successful implementation of the electrical drive system— safety operation, timely installation, availability, energy efficiency, minimum maintenance and extend its use as tool to assist during mill liner exchange—customers are justified in their scrutiny and slow adoption of new drive technology. From the first installation of low, fixed speed synchronous motors to the introduction of the current source and further voltage source variable frequency drive, innovations require long periods of time and mining customers willing to push the industry forward. In recent years, the variable frequency drive has been the stepping stone for a new generation of mill drive technology. In use for decades in other heavy industrial applications, the drives allow for system optimization in a myriad of ways. The most dramatic of changes is in the design of the motor. Where in the past motor design was bound by line frequency, today the designer can optimize machine size and, more importantly, eliminate the need entirely for the synchronous motor. Induction motor design has now progressed to the point where low speed operation is possible at efficiency levels nearing those of the synchronous design. Moreover, the simplicity of the squirrel cage design means that availability, reliability and spare part requirements are greatly improved. As the next step in the evolution of large pinion driven grinding mills, the low speed induction drive offers a new reliable and robust system to the market.IntroductionAs deposit grades continue to decline, new ways of processing ever greater concentrator throughputs have been required to maintain throughput efficient and profitable operations. Furthermore, the high risk nature of mining developments requires a constant search for safer, higher availability and more efficient equipment design. Limitation of downtime is a key factor in ensuring mining operations can be sustained through volatile market conditions. Often processing the entire mine throughput through just 1 or 2 lines, the crushing and grinding circuits are of particular criticality to the uptime and, thus, profitability of any mining operation."

Jan 1, 2016