Search Documents

By Jiang Feng, Zhang Libo, Peng Jinhui, Guo Zhanyong, Ju Shaohua, Lei Ting

The clean utilization of the residue containing chloride, CuCl residue, produced from zinc hydrometallurgy is very important for the recycle of valuable metals. And drying is the main process in recycling. In this study, response surface methodology was used to optimize operating conditions of the drying of CuCl residue in a convection oven and desirability function used as the methodology for the optimization. Optimization factors were air temperature (80–100°C), material thickness (10–25mm) and process time (80–120min) while investigated responses was final moisture content. The optimum conditions were found to be the temperature of 95.48°C with the material thickness of 13.47mm for the process time of 89.48 min. Under optimum conditions, the predicted moisture content of CuCl residue was 4.11% while the experimental date was 4.13%. The experimental value after process optimization was found to agree satisfactory with the predicted value. After drying, XRD was used to analyze the main phases of CuCl residue. The CuCl residue is made up of CuCl,Cu2O, ZnS and other compounds.

Jan 1, 2015

By Chang Wei, Zhigan Deng, Minting Li, Cunxiong Li, Xingbin Li

A direct hydrometallurgical process of extraction molybdenum and nickel from molybdenum-nickel ore by pressure water leaching without reagent was studied. The extraction of Mo and Ni from molybdenum-nickel ore by oxygen pressure leaching, which exploit the characteristic of molybdenum-nickel minerals contain high concentration amorphous sulfide which has highly active, and make the most of easily oxide to sulfuric acid and sulfate at low temperature and excess oxygen presence of the amorphous sulfide. Under oxygen pressure conditions, considerable molybdenum and almost all the nickel were extracted into solution in the leaching process. The results show that with the leaching time for 3~4h, temperature at 150o C, liquid-to-solid ratio of 2mL/g, mineral granularity of 0.074mm, oxygen partial pressure of 0.4~0.5MPa without other reagent, molybdenum leaching percentage can be over 80% and nickel leaching percentage can be more than 97%. Furthermore, about 80% sulfur in the Mo-Ni ore has been transformed into sulfuric acid.

Jan 1, 2014

By M. Castelli, C. Scavia, S. Marello, A. Allodi

ABSTRACT – This paper investigates the possibility of interpreting the shear band evolution in hard soils and soft rocks as the result of shear propagation from pre-existing natural defects. Thesis done through the application of the principles of Fracture Mechanics, a Slip-Weakening Model(SWM) being used to simulate the non-linear zone at the tips of the discontinuity. Experimental observations have been carried out on prismatic samples of Beaucaire marl through biaxial compression tests in plane strain conditions. A numerical simulation confirms the validity of the proposed approach. RÉSUMÉ – Cet article présente la possibilité d’interpréter l’évolution des bandes de cisaillement dans les roches tendres et les sols raides comme le résultat de la propagation pour cisaillement à partir d’un défaut préexistant. Le Slip-Weakening Model (SWM) a été employé pour modéliser la zone non linéaire a l’extrémité d’une discontinuité. Nous présentons des observations expérimentaux obtenues à travers des essais de compression en déformation plane sur des échantillons prismatiques de marne. La simulation numérique d’un essai confirme la validité de la méthode proposée. KURZFASSUNG – Die vorliegende Arbeit versucht die Ausbreitung von Scherzonen in(bindigen) Böden und im Lockergestein anhand der Entwicklung von Scherrissen ausgehend vonexistierenden Schwachstellen zu erklären. Die Umsetzung erfolgte mit Hilfe der Bruchmechanik,für die Modellierung der nichtlinearen Zone an den Rissenden wurde ein Slip-Weakening-Modell(SWM) eingesetzt. Es wurden zweiaxiale Druckversuche an prismatischen Probekörpern vonBeaucaire Mergel unter der Bedingung eines ebenen Verzerrungszustandes durchgeführt. Dienumerische Untersuchungen bestätigten die Annahmen der untersuchten Theorie.

Jan 1, 2003

By Edgar C. Bain

A NUMBER probably a sizable group of person with a dominant interest in metals maintain contact with the developments in ferrous metallurgy by reading week by week, as time permits, some four or five periodical devoted in considerable part to this field. It seems possible that some of these, like ourself, find it difficult to see the net results of the development day by day in clear perspective, The impression sometimes seems blurred by the uninterrupted succession of so many accounts, or out of focus from the very impact of so many reports of new things enthusiastic, well written, and understandable though they usually are. It is at times almost as though one were trying to observe, from a fastmoving vehicle, objects all too near at hand. Or perhaps this impression is merely a manifestation of our individual hyperopia ; in which case we should content ourself with an observation that it would be more satisfactory on the whole to discuss in 1941 the metallurgical advances of 1930-35 than those of

Jan 1, 1941

A reliable laboratory method to characterize the response of free gold particles to flash flotation conditions has been developed. The test has been performed on free milling gold ores as well as synthetic ores, using either a gravity concentrate or gold powder as the gold source, to assess the floatability of gold particles. Trends in free gold flotation kinetics, as well as size and milling effects, were identified for gold recovery based on the different feed types, reagent dosages, and residence times. It was shown that the ultimate recoveries and kinetic trends of gold particles from the gravity concentrate could be enhanced with increased dosage of collector, potassium amyl xanthate. Interestingly, in comparison to gravity-recoverable gold, recovery from pure Au powders was better in collectorless flotation, and cumulative recovery decreased with higher levels of collector addition. Improved coarse particle recovery appeared linked to increased collector additions for both the gravity concentrate and the pure gold powders. In general, coarse gold particles demonstrated slower kinetic rates thaen the fine or intermediate components incomparable tests.

Jan 1, 2015

By T Do, J Siliezar, M Larson

With the expansion of magnetite projects in Australia has come the opportunity to take advantage of newer technologies that were not necessarily available when the magnetite industries of North America and Europe were maturing. One of these technologies is the IsaMill, originally developed for the economic treatment of ultra-fine grind (UFG) duties of Mount Isa Mines. As understanding of the IsaMill has increased, so too has the ability to process coarser feeds while maintaining the same energy efficiency advantage and tight product size distribution that originally made the IsaMill so attractive. In the case of magnetite the hard non-elastic ceramic grinding media is ideally suited to the grinding duty when compared to steel grinding media. The centripetal separator and naturally steep product size distribution curve provide a mill discharge that maximises the critical concentrate grade. This paper analyses the effect of the IsaMill grinding technology on the full-scale Ernest Henry Mine (EHM) magnetite operation along with pilot and lab scale demonstrations of optimisation. Issues encountered and the solutions to maximise the mill throughput and quality are examined in an effort to promote better understanding across the industry. CITATION:Larson, M, Do, T and Siliezar, J, 2013. Enhancing magnetite returns - the benefits of IsaMilling, in Proceedings Iron Ore 2013 , pp 411-416 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Sergei Decterov, Peter Hayes, Evgueni Jak, Taufiq Hidayat, Denis Shishin

Copper smelter operations around the world are under sustained pressure to reduce costs and increase output. Through the provision of reliable data on fundamental properties of the chemical systems the opportunities for improvements of industrial copper production can be identified. Experimental and modelling studies on phase equilibria, thermodynamics of copper slag/matte/metal/gas systems have been combined into an integrated research program undertaken at PYROSEARCH. Experimental phase equilibria studies involve high temperature equilibration in controlled gas atmospheres, rapid quenching and direct measurement of compositions of equilibrium phases with electron probe X-ray microanalysis (EPMA). Thermodynamic databases development and modelling is undertaken using the computer package FactSage in conjunction with advanced models used for complex solution phases. Progressive development of these research methodologies has brought significant advances in characterisation of these complex systems, including a new optimised thermodynamic database for the copper-containing slag system Cu2O-Al2O3-CaO-FeO-Fe2O3-MgO-S-SiO2.The new data and models can now be applied to assist in improvements of the processes. The effects of changes to chemistry and process conditions within the smelting reactor can be examined. Several examples of new descriptions of the phase chemistry of the Cu2O-CaO-SiO2 and Cu2O-FeO-Fe2O3-SiO2 systems in equilibrium with metallic copper showing calculated and experimental data are presented.

Jan 1, 2014

By M. Clair Smith

This report is one of a series being prepared by the Bureau of Mines on exploration, development, mining methods, and costs at various open-pit mines in the United States. These reports have been prepared in cooperation with various mining companies. A similar program, conducted from 1928 to 1939, was generally conceded to have contributed to improving the efficiency of mining operations. The purpose of these reports is to promote development and conservation of our mineral resources by disseminating technological information on mining methods and practices. This report describes exploration, development, equipment, and mining by open-pit methods of the remainder of an ore body that had been previously worked by underground methods. The Tripp pit of the Consolidated Coppermines Corp. is located at Kimberly, Nev., a small mining company town having an elevation of 7,250 feet, 9 miles by road west of Ely, Nev. (fig. 1). The pit extends over the area formerly mined by underground methods from the Morris and Brooks shafts.

Jan 1, 1962

By S. M. Shelton

Tests employing various ore-dressing methods were made on a manganese wad ore from the W. A. Chinn property in the Batesville-Cushman district of Arkansas in an effort to develop a practicable procedure for the production of ferromanganese-grade concentrates. The ore body occurs as a bed approximately 7 feet thick in the residual clay of the Ferndale limestone formation5/. The crude wad ores are soft aggregates of various oxides of manganese, which are loosely bonded together. Hard lumps of high-grade ore are disseminated throughout the wad. Hausmannite, pyrolusite, and psilomelane are the principal minerals. Some clay is present, but most of the gangue consists of leached fragments of the original siliceous and calcareous rocks in which the manganese occurred. In addition, hydrated oxides of iron, which axe present, also must be considered as gangue. Definite phosphate minerals have not been identified.

Jan 1, 1942

The excavatability of the rock mass in a proposed open pit mine at Globe-Progress has been assessed. The rock mass was initially evaluated by determining variations in seismic velocity and by using the Revised Size-Strength Chart. These two assessments should be performed during the feasibility or early investigation stages of a project. A complete rock mass excavatability assessment using a suite of geological and geotechnical properties was then performed using three methods: RMR System; Modified Rippability Rating; and a productivity estimation method. These three methods should be applied during the investigation and design stages of a project. The preliminary assessments show that most of the open pit rock mass is expected to be rippable. The complete assessment differentiates weak, fair and good rock masses within the open pit. Weak rock mass exists along the Globe-Progress Shear zone, located along the northern and eastern pit walls and also in the western pit wall where the Chemist Shop Fault is located are both regions are expected to be diggable. Relatively weak rock mass also exists along the Globe-Progress Shear axial hinge. The Globe-Progress Shear limbs are generally fair to good rock where moderate to hard ripping should be expected.

Jan 1, 1996

By C. E. Birchenall, W. Batz, H. W. Mean

AT temperatures between 1095' and 1347ºC, 13 runs have been made on the diffusion of silicon in iron. In two of the runs the couple compositions were entirely within the loop of the Fe-Si system; the base alloys contained 0.0 and 1.0 wt pct Si. The other runs in which the couples consisted of a 2.3 wt pct Si alloy welded to a 3.7 pct Si alloy were a phase throughout. The alloys were made by melting electrolytic iron and commercially pure silicon. Trace impurities were not determined. The butt welded couples were diffused in an inert atmosphere of argon or hydrogen. After cooling, cuts of two mils or greater thickness were machined parallel to the weld interface. The chips were analyzed for silicon. When the concentration and distance data were examined on the conventional probability plot,' no marked variation of the diffusion coefficient with concentration was indicated over the narrow composition ranges employed. Therefore, a single diffusion coefficient is recorded for each run in Table I. The temperatures and atmospheres of the diffusion anneal are listed along with the compositions of the base alloys. For a iron the silicon diffusion coefficient is given by the equation: D = 0.44 e-48,000/RT where R is the gas Constant and T, the absolute temperature. However, since the scatter in the data is fairly large, the activation energy may be in error by as much as 6000 cal per g-atom. The two ? iron points do not permit estimation of the activation energy with any reasonable certainty. They do indicate that the coefficients reported by Smithells2 and Jost,3 based on the work of Fry,4 are much too high. Although very dilute solutions in iron of manganese,5 nickel,8 cobalt,7 and molybdenum8 give dif- fusion coefficients quite close to those obtained for self-diffusion in iron, the silicon values are considerably higher, though of the same order of magnitude. This seems to be consistent with the fact that the silicon atom is the only one of those listed here which is appreciably smaller than iron. The authors are grateful to the Office of Naval Research for their support of this work under Contract N6ori-47, Task order IV, Project NR 031-184, to J. K. Stanley and the Westinghouse Research Laboratories for the silicon alloys used, to several steel companies for the silicon analyses, and to C. Wells, of the Metals Research Laboratory, Carnegie Institute of Technology, for numerous suggestions during the course of the work. References 'C. Wells: Atom Movements (1951) Chapter 2. A.S.M. 2C. J. Smithells: Metals Reference Book (1949) p. 405. Interscience. Pub. Co. 3W. Jost: Diffusion (1952) p. 223. Academic Press. 4 A. Fry: Stahl und Eisen (1923) 43, p. 1039. T. Wells and R. F. Mehl: Trans. AIME (1941) 145, p. 315. "C. Wells and R. F. Mehl: Trans. AIME (1941) 145, p. 329. 7M. F. Hawkes and R. F. Mehl: Trans. AIME (1947) 172, p. 467; Metals Technology (August 1947). .J. L. Ham: Trans. A.S.M. (1945) 35, p. 331.

Jan 1, 1953

By Taylor GP

Mining Lease SML 57 was registered to Mount Kasi on 5 January, 1995. The Mount Kasi gold mine is located in Vanua Levu, Fiji's second largest island and operated from 1932 to 1946 producing 261,000t of ore at an average grade of 7.5g/t Au. The deposit represents a structurally controlled style of high sulphidation copper gold mineralisation with peripheral low sulphidation mesothermal vein type gold mineralisation. The resource consists of 1,048,000 tonnes of residual soils (eluvium) containing 1.9 g/t Au at 0.5 g/t Au cut off and 1,240,000 tonnes of hard rock at 3.0 g/t Au and 1.0 g/t Au cut. 94 drill holes, 298 auger holes and 85 pits were modelled to outline the resource. 29% of the pits bottomed in mineralisation and it is likely the full thickness of eluvium has been understated. The pit is scheduled to produce 500,000 tonnes of ore per annum to yield 35,000 ounces of gold with an initial 2 years of eluvial ore followed by a further 2 years of hard rock ore. Total capital costs are estimated to be less than 10.0 million dollars with construction planned to commence in 1995. The likelihood of locating further ore is high.

Jan 1, 1995

By Wilbert J. Huff

This is the sixth of a series of annual reports describing the work of the? Explosives Division, Bureau of Mines, United States Department of the Interior.3/ It deals particularly with the activities of the division from July 1, 1940, to June 30, 1941. The studies outlined in this and preceding reports of the series have been conducted under the direction of the author and the respective unit leaders, to whom specific credit is given.

Jan 1, 1942

By Corale L. Brierley

Beneficiation of phosphate in the southeastern United States generates a slurry of finely divided clay. These clay-wastes are impounded to allow the particulates to settle. The aggregation of phosphatic clay-slime wastes and slimes produced from potash beneficiation by microbial processes was studied using several bacterial species known to produce polymeric substances. Experiments included flocculation capacity of clay-slimes by whole cells, the determination of respiratory activity of whole culls in the presence of phosphatic clays, observation of clay flocculation rates by polymers derived from these organisms, and clarity of polymer-flocculated clay suspensions. The polymer-producing organisms exhibited little capacity for flocculating phosphate and potash clay-slimes. Fungal spores of Cladosporium cladosporioides (isolated from a phosphate clay-waste impoundment), when agitated with clay-slime for several days, caused the clay to form pellets. Separation of the clay/fungal pellets (density 1.1 g ml-1) from the process water might he possible using a screening technique. Studies with C. cladosporioides included the determination of suitable energy substrates and supplements for growth, absorption studies of a pigment produced by the organism, determination of the time required for bioflocculant production by the organism, and an elucidation of the conditions required for the pelletization of clay-slimes by the fungus.

Jan 1, 1982

By Wilbert J. Huff

This is the sixth of a series of annual reports describing the work of the Explosives Division, Bureau of Mines, United States Department of the Interior.3/ It deals particularly with the activities of the division from July 1, 1940 to June 30, 1941. The studies outlined in this and preceding reports of the series have been conducted under the direction of the author and the respective unit leaders, to whom specific credit is given.

Jan 1, 1942

By Derk G. E. Kerfoot

The extractive metallurgy of nickel and cobalt has proved to be a particularly fruitful area for innovation in hydrometallurgy and electrometallurgy ever since the development of the Hybinette process for nickel in the early 1900's. In current practice, nickel concentrates are generally smelted to high grade mattes which are then refined to metal by a combination of hydrometallurgy and electrometallurgy, although low grade copper-nickel concentrates are refined directly by the ammonia pressure leach process. Matte refining processes in commercial operation include the direct electrolysis of matte, the ammonia pressure leach, sulphuric acid leaching using air or oxygen at elevated pressure, or at ambient pressure, and chlorine or chloride leaching. Refined nickel is recovered either as electrolytic cathode, or as metal powder by hydrogen, reduction. Hydrometallurgy has also found application in the treatment of nickel laterite ores, both in the reduction roast ammonia-ammonium carbonate leach process, pioneered by Caron and in the Moa Bay acid leach process. Cobalt is recovered as a co-product of copper in central Africa, and as a byproduct of hydrometallurgical nickel refining elsewhere. In the African plants, the copper-cobalt concentrates are roasted and leached in sulphuric acid solution, and copper and cobalt are recovered separately from the leach solution by direct electrowinning. A variety of hydrometallurgical techniques are used for the separation of cobalt from nickel, including selective precipitation and crystallization, solvent extraction, and ion exchange. Like nickel, refined cobalt is recovered either as electrolytic cathode or as metal powder by hydrogen reduction.

Jan 1, 1988

A colloquium on 'Recent Developments in Wearresistant Materials', organized by the Technical Programme Committee: Physical Metallurgy of the SAIMM, was held at Mintek on 7th May, 1985. After delegates had been welcomed by Dr P.T. Wedepohl, Chairman of the Organizing Committee, Mr J.D. Austin, President of the SAIMM, delivered the opening address. Corrigenda to article on copper* I read with considerable interest the recent articles on copper by Mr C.O. Beale as published in the Journal. However, in Part 11 the section dealing with Prieska Copper Mines (Pty) Limited contained several factual errors, details of which are given below.

Jan 1, 1985

By E. P. Deliac

The aim of this joint work between the French Coal Board and the Paris School of Mines is to be able to practically model the behaviour of a transverse drum cutting rock with picks. First a theoretical approach leads to the concept of cutting curves, giving forces and torque against penetration per drum revolution. Then experimental evidence, from full scale and reduced scale testing, validated and confirmed the theoretical shape of the curves. Finally practical applications are given, to improve the design or use of a shearer (or continuous miner). A micro-computer program is being developed to predict the cutting performances of a machine in certain conditions.

Jan 1, 1985

By J. P. Sancho, L. F. Verdeja, J. I. Verdeja

"This paper analyzes the present state of the different processes competing to keep their market shares within the future iron and steel business sector.The continuous transformations in the steel making process are also studied here. These transformations have happened especially during the two last decades obviously favouring steel price, properties, quality and environmental compatibility in the new millennium. IntroductionIn the early 1980s, world steel production reached a historic figure; specifically in 1982, the amount was 645 Mt (Verdeja et al., 1993). This might have been one of the reasons why the United States, Japan and the European Community drew up a declaration of principles after which the leading industries and sectors in the following century’s development would be: advanced materials, also known by the very diffuse term of new materials; information technologies; and biotechnology (Eager, 1998).On the threshold of the 21st century, it can be inferred that information technologies (computers and telecommunications) have progressed spectacularly. Nevertheless, there have been downsides too; technology develops so quickly that after a few months the products are obsolete. Environmental problems may also appear in a few years due to storing so many useless devices. At the same time, the achievements of biotechnology did not meet the optimistic forecasts made in the early 1980s.On the other hand, it is also curious that some solutions for the environmental problems generated by star technologies of the new millennium, such as computers and biotechnology, are closely linked to the iron and steel industry. For example, blast furnaces in Germany and Japan are prepared for burning residua by introducing polymer materials from computers and other electronic prepared devices through their tuyeres, while cement tube furnaces can destroy any organic residua from different origins."

Jan 1, 2002

By John P. Borovsky

A 3-year study was conducted to evaluate the problems and benefits of using vegetation to stabilize tailing from a potential Minnesota copper-nickel milling operation. The project consisted of three separate investigations: a waste characterization study, a greenhouse study and a field study. With few exceptions, the physical and chemical characteristics of the tai ling were found to lie within the range of properties of Minnesota soils. The tailing lacks organic matter; is deficient in nitrogen, phosphorus and potassium; and may contain elevated levels of soluble salts and heavy metals, particularly copper and nickel. Numerous grasses, forbs and woody plants will tolerate the tailing as a rooting medium. Peat incorporation and topsoil dressing provided few benefits to the revegetation process which were not provided by a fertilizer application. With fertilization, grass/legume production in the tailing was comparable to local agricultural yields. Concentration of heavy metals in grasses grown in the tailing were generally below suggested tolerance limits for plants and animal forage. Legumes tended to accumulate higher concentrations of copper and nickel, and metal uptake of most plants was positively correlated with rate of fertilization. Tailing drainage water contained elevated levels of heavy metals, and establishment of vegetation had little effect on the quantity and quality of tailing drainage water. However, topsoil dressing significantly increased drainage water volume when compared to unvegetated control plots. Copper-nickel tailing revegetation recommendations were developed.

Jan 1, 1983