Search Documents

By Wolfgang Kern

More and more coke oven plants worldwide face the task to improve their emission reduction at their coke oven batteries. In the 90’s PROven® was invented and developed by DMT to regulate the inner pressure of a single coke oven chamber. Generally, most of the coke oven chambers can only close and open their connection to the collecting main but without the possibility to regulate the pressure during the carbonization time. Through the installation of PROven® the load on the coke oven door sealing system and the charging lids will be decreased and so does the emissions of crude COG as well. The current PROven® system, installed in the collecting main, does not only regulate the chamber pressure, it replaces the valve between the goose neck and the collecting main, too. This variable pressure control allows decreasing the leakages at the emissions sources to a minimum and allows operating the collecting main under optimum pressure. Subsequently, this will lead to enhanced emission reduction. PROven® proved its value with more than 2,100 units installed by licensee worldwide. Nevertheless, DMT is always focused on its client’s needs and therefore enhance PROven® to provide the Best Available Technique (BAT). Among the main features of the now available system is the plain arrangement with a higher reliability and the possibility to install the system outside of the collecting main without modifying it. Hence, upgrading coke oven plants during operation is possible without any noticeable impact on the plant operation.

Aug 1, 2018

By Marcus Vinicius Dias Garcia

O presente trabalho tem por objetivo contribuir para a preservação refratária de baterias de coque, apresentando uma metodologia de planejamento e controle. A condição dos refratários de baterias de coque é crucial para sua produtividade e para o cumprimento de diretrizes ambientais. São desafios (i) a identificação precoce de danos e previsão de seu efeito no desgaste global da bateria, para hierarquia de reparos; (ii) a seleção da técnica apropriada a cada reparo. No presente trabalho, os autores compilam o estudo da progressão de danos sob diferentes tipos de reparo ao longo de mais de 30 anos em baterias heat-recovery e convencionais, de diversos modelos construtivos, e o combinam a tecnologias de inspeção para consolidar uma metodologia de gestão da preservação refratária. A metodologia foi aplicada em baterias localizadas no Brasil, avaliando a condição de mais de 400 fornos em 90 dias. Para a bateria mais crítica, foi identificado um potencial de prorrogação de vida útil em torno de 10 anos.

Aug 17, 2017

By Hongshuang Di, Tianyu Zhang, Huiqiang Huang

A CMnSiAl transformation induced plasticity (TRIP) steel was used to study the effect of retained austenite on room-temperature mechanical properties. The steel plates with retained austenite were obtained by hot rolling, cold rolling and subsequent continuous annealing. The starting and finishing temperature of hot rolling are between Ac1 and Ac3. Reduction ratio of cold rolling is 75%. The continuous annealing is carried out at different intercritical temperatures. The relationship between work hardening exponent and retained austenite was discussed. The results show that, the Ac1 and Ac3 were much high because of the alloy elements, and the temperature range between them was wide. Due to the high hot rolling temperature, the grains was hereditarily refined as a result of dynamic recrystallization. Annealing at intercritical temperature of 930 ºC, retained austenite with relatively high stability reached a maximum volume fraction of 25%, a maximum total elongation of 30.2% and a best ultimate tensile strength × total elongation of 20.1 GPa·%. Instantaneous work hardening exponent reflects strengthening mechanisms at different strain stages. The TRIP effect of retained austenite is the main mechanism during deformation. With retained austenite of sufficient amount and high stability, continuous work hardening was observed in the tensile specimen of 930 ºC.

Oct 1, 2019

By Mery-Cecilia Gómez-Marroquín

O presente trabalho trata da formação da ferrita de zinco a partir da mistura e posterior reação solido-solido entre o óxido de zinco e óxido de ferro - Fe2O3 puros em proporções equimolares. A faixa de temperatura onde teve lugar a formação foi entre 1073 e 1373 K. Testes de redução da ferrita da zinco sintética-ZF e pós de aciaria elétrica–EAFD foram realizadas usando misturas de CO e CO2 que variaram entre 50 e 100% CO. Ambos os testes (formação e redução de ZF e EAFD) foram suportados usando técnicas de caracterização física, química, estrutural e microscópica. No caso da redução, foi observado que tanto a temperatura como a percentagem de CO, foram os fatores que, mais afetarem a redução de ferrita de zinco contida no EAFD. A máxima percentagem de redução da ZF foi 85%, para 100% CO, 1373K e 105 min, e 52%, para 50% CO, 1373K e 105 min. Por outro lado, atingiu o 100% para 100% CO, 1273K, em 80.75 min, 60%, para 50% CO a 1373K durante 105 min. no caso da redução do EAFD

Aug 17, 2017

By Renan Gurgel Pinho

O objetivo deste trabalho é investigar a esferoidização do aço SAE 1080 e os respectivos efeitos da variação do tempo na microestrutura final e na dureza do material. O aço SAE 1080 foi submetido a recozimento isotérmico, por tempo prolongado, utilizando-se 90, 100 e 120 horas de aquecimento à temperatura de 715ºC. Os resultados mostraram que é possível esferoidizar o aço SAE 1080 nos respectivos tempos escolhidos e perceber aumento da quantidade de esferoiditas, assim como decréscimo na dureza.

Aug 16, 2017

By Madson Pereira Martins

A utilização de resíduos oriundos de processos industriais tem se tornado uma prática muito recorrente em todo mundo devido à questão ambiental. A legislação brasileira estipulou parâmetros rígidos de destino destes materiais e a indústria viu na construção civil uma possibilidade de utilização. Este trabalho tem como objetivo a caracterização do pó de pedra de gnaisse para utilização em concretos. Serão realizados ensaios de granulometria, determinação de massa especifica e material pulverulento. Os resultados mostraram a viabilidade da incorporação deste resíduo para a produção de concretos.

Aug 16, 2017

By Bruno Cordeiro Costa

Inseridas em um mercado extremamente competitivo, as empresas siderúrgicas vêm buscando aprimorar seus processos produtivos e de gestão de forma a reduzir custos de produção e garantir sua sustentabilidade. A principal parcela do custo de produção da empresa em relação a um aço inoxidável ligado ao Cromo e Níquel está na Aciaria, e a carga metálica representa mais de 80% deste valor. Visando aumentar a competitividade, foi aberto um projeto para otimizar a carga metálica na Aciaria. A redução da mistura de escórias é uma fase deste projeto. O propósito do presente trabalho é mostrar a metodologia adotada para otimizar o processo de recuperação de sucata das escórias de aços inoxidáveis, minimizando a ocorrência de misturas de escórias, para maximizar seus teores de Ni e Cr e, consequentemente, reduzir o uso de fontes mais nobres e caras destes elementos. Foi adotada a filosofia “Zero de Escória no Chão” e, para alcançar este objetivo, várias ações foram implantadas. Considerando 2011 como base 100%, o teor médio de Ni da sucata recuperada de 3XX aumentou 45% em 2013 e o teor médio de Cr subiu 36% na sucata recuperada neste mesmo período. Como consequência direta da redução da mistura de escórias de grupos de aços diferentes ao longo de todo fluxo produtivo, ocorre a redução dos residuais de Ni e Cr nos aços carbono e elétricos e de Ni nos aços 4XX. A metodologia adotada foi eficiente e os objetivos do projeto foram alcançados.

Jul 30, 2018

By Zhi Zhang

The ever increasing demand of high performance rolls in the late finishing stands (F5 – F7) for hot strip mills (HSM) requires better product solutions from roll suppliers. Roll development activities never stop at Union Electric Åkers (UEÅ) in order to meet the requirement. The HYBRID STEEL, a new concept of roll materials especially for the late finishing stands in the HSM, is successfully developed in UEÅ. This paper reviewed the development of previous ICDP as well as enhanced ICDP (eICDP) roll materials, and, the novel HYBRID STEEL roll grade. Rolls manufactured by this new grade have been used in several European mills. A significant improvement over the enhanced ICDP rolls has been observed.

Oct 30, 2017

By Karl K. Bagger, Felipe Bertelli

The competitive scenario of steel industry requires studies and developments to improve manufacturing processes focusing on increasing productivity and reducing costs. The practice of coating rolls for cold rolling with the chrome aims to increase the rolling campaign, reducing their wear by increasing the surface hardness, which guarantees a greater homogeneity in the surface of the rolled products. The present paper presents a study on the effect of the chromium coat on a forged steel rolls on the wettability of a SkinPass solution. The hardness of the coated layer and the contact angle were measured for two concentrations of solution on two types of surfaces, comparing the coated and uncoated surfaces. The results show that there is an influence of the coating on the wettability of the fluid when comparison are made with chrome coated and uncoated materials, being verified through tests in Goniometer. The productivity of the coated rolls showed higher productivity than the uncoated ones.

Oct 1, 2019

By Shian Jia

Ultrasonic Stirring Technology (UST) is used in this study to manufacture Al-based nano-composites. Ultrasonic cavitation plays an important role in refining the microstructure, dispersing the nanoparticles and breaking up clusters of nanoparticles. In this paper, 6061/A356 alloys and Al2O3/SiC nanoparticles are used as the matrix alloys and the reinforcements, respectively. The nanoparticles were inserted into the molten alloy and dispersed by ultrasonic cavitation and acoustic streaming. A previously developed multiphase Computational Fluid Dynamics (CFD) model was used to study the cavitation and the nanodispersion phenomena during ultrasonic processing of these alloys. A comparison between the mechanical properties of the as-cast 6061 and 356 alloys and nano-composites has been performed.

Aug 16, 2017

By Eduardo Montenegro

Apesar da relevância e interesse do tema de gerenciamento de alarmes na comunidade técnica industrial, observa-se que poucas empresas têm, de fato, implantado e conseguido extrair melhores resultados na eficiência e segurança operacional de suas plantas. O presente trabalho visa, a partir das experiências dos autores em implantação e acompanhamento de vários sistemas de gerenciamento de alarmes na indústria, discutir os principais motivos pelos quais estes sistemas falham em conseguir índices melhores em operação, monitoramento e gestão de alarmes. Além disso, propõe-se neste trabalho que estratégias, práticas e ferramentas sejam adotadas para que se consiga o máximo de benefício operacional ao se implantar e manter tais sistemas.

Aug 16, 2017

By Gilmar Ferreira Bataglia

The possibility of parameterization of hot tensile data together with creep data is investigated, for Aluminium Alloy 7475-T7351. This study represents part of a broader research program aiming at the validation of a methodology recently proposed for analyzing both kinds of data together, considering different metallic materials. The results presented in Part 1 of this work, were analyzed according to 4 traditional methods of the literature for parameterization of creep data, namely: Larson-Miller, Orr-Sherby-Dorn, Manson-Succop and Manson-Hafferd. The compatibility of the hot tensile test results with those of creep is remarkably good, indicating the possibility of using both kind of data together also in extrapolation schemes. The criterion proposed for equivalence between hot tensile and creep data is verified to work well also for this kind of material, under the present experimental conditions.

Aug 8, 2018

By Ismar Antônio Sardinha

Usually outer straight steel tubes are used to blow supersonic oxygen into LD converters (BOF) to make liquid steel, although conical tubes are used too. Inner tube for oxygen blow and intermediary tube for water IN and water OUT are normally straight steel tubes. Present paper shows the influence of outer tube shape and metal used to in lance cooling and, consequently, a skull retention on lance surface. There are two parameters more important related to lance cooling: velocity of water out and the total lance cooling by addition of thermal conductivity of outer tube metal to it. For this comparison outer tubes are made of carbon steel or copper, and can be straight or conical. As related to velocity of water OUT, outer straight tubes have bigger efficiency than conical tubes. As related to total lance cooling, outer tube metal made of copper has much bigger efficiency than steel because of its thermal conductivity 7 to 12 times more depending on work temperature. The lance cooling has much bigger efficiency for the patented SKULLS3® technology with no skulls on the lance and no skulls into the mouth of LD converters (BOF).

Aug 17, 2017

By Stefan Thelen

In November 2013 Salzgitter restarted their tandem mill after two weeks of shutdown, during which the existing mill entry equipment has been removed and replaced by new entry area equipment including pay-off reels, welding machine and a vertical entry looper for continuous feeding of the 5-stand tandem mill. It turned out to be beneficial to both product quality and production capacity.

Aug 16, 2017

By Flavia de Paula Vitoretti

Pelletizing of iron ore fines is an important process used to produce high quality of raw materials for the subsequent reduction processes in the ironmaking industries. The process involves the production of green pellets and subsequent induration on a traveling grate furnace to promote inner partial melt and agglomeration which confer physical and metallurgical proprieties appropriated to the subsequent reduction processes. The pellets are produced with addition of charcoal to improve efficiency in the reduction processes. The lignin coal from sugarcane straw is an alternative source to replace the charcoal or coke in the self reduction of pellets. This work focused on the influence of biomass on the chemical kinetics parameters inner agglomerate pellet structure under industrial process conditions of the travelling grate furnace due hot gas flows within the pellets.

Aug 1, 2018

By Martin Chabicovsky, Milan Hnizdil

Emulsions are frequently used for the cooling and lubrication of working rolls during the cold rolling. The fact that the lubrication and cooling are not separable makes the optimization of both functionalities difficult. The higher emulsion temperature decreases the cooling efficiency compared to cold water. Heat transfer and fluid flow laboratory (Czech Republic), CRM (Belgium), Tata steel (Netherlands) and Henkel (Germany) cooperated on the increasing of a cooling efficiency during cold rolling. Part of this research was focused on an influence of the emulsion composition on a cooling intensity. The cooling efficiency was laboratory investigated. The stainless steel sample with thermocouple was heated and then it was cooled by a nozzle. Tests were performed with various emulsions and pure water. The heat transfer coefficient was computed from measured temperatures. The cooling intensity (heat transfer coefficient) of all tested emulsions was similar but an increase of the cooling intensity was found with water. Further various emulsions concentrations were tested. Results showed decreasing cooling intensity with increasing oil concentration. Adding additives therefore is thought to cause a noticeable decrease of the cooling intensity.

Oct 1, 2019

By Martina Cadorin

Activated nanoporous biocarbon (aNBC) was prepared using E. grandis wood as a precursor material. Oxidated activated nanoporous biocarbon (ox-aNBC) sample was obtained from the aNBC by oxidation with nitric acid. The samples were tested as Pt nanoparticles catalysts support for ethanol oxidation reaction and as electrode materials for supercapacitors. The porous structure, chemical properties, and the structural and morphological characteristic of the materials were correlated with their electrochemical behaviour. Biocarbon materials showed similar high specific surface area. The oxidation treatment increases the content of the oxygenated and nitrogenated surface functional groups but without appreciably change in the nanostructure characteristic. The aNBC supported Pt nanocatalyst has better electrocatalytic performance for EOR. Oxygenated functional groups have a marked effect on the supercapacitors electrode behaviour, increasing the total electrical capacitance by pseudocapacitive contribution, but with a negative effect on the cell electrical resistance and cell response time.

Oct 30, 2017

By Débora Cardoso de Oliveira Silveira, Jean-Christophe Huber, Hamzeh Hamadeh, Kateryna Pastel, Guillaume Brosse

The dynamic behavior of oxygen gas flow, determined by the lance nozzle and blow pattern, is a key factor for determining jet efficiency in BOF Steelmaking. The present work compares the performances of Laval and parabolic nozzles with the aid of the Computational Fluid Dynamics (CFD). The Method of Characteristics (MOC) was applied to design a minimum length parabolic nozzle. The results show that the parabolic nozzle generates more uniform and stable jet, with 2% longer potential core and supersonic length and less shock waves. For the parabolic nozzle, the pressure nearby the nozzle wall is higher, which can protect this region from reverse flow of converter gases and offer longer life for the lance tip. Likewise, the flow rate variations would affect less this nozzle. In addition, the nozzle wear was investigated, and the parabolic nozzle has proven relatively less sensitivity to the presence of this deformity.

Oct 1, 2019

By Breno Totti Maia

In the present paper, a new energy balance equation was developed, considering the slag phase, in order to define the effects of jet penetration and determine a new value for the factor K. The factor K measure the resistance to momentum transference between exit nozzle and metallic bath. The experiments were performed based on the same conditions of the article used as a comparison. The results showed the same behavior between the experiments and it was possible to determine a new value for the factor K, which changed from the unit order for the metal phase system to hundredths order for the metal and slag phase systems. These results are considered unprecedented.

Aug 17, 2017

By Benito Barbabela e Silva

O pelotamento é a mais complexa etapa de aglomeração de finos de minério de ferro. Sua resposta é naturalmente oscilante, sendo bastante influenciada pelas características físicas obtidas nos processos de beneficiamento mineral que a precedem e tem papel crucial para a etapa de tratamento térmico de sinterização à jusante. O presente trabalho aborda o processo de classificação de pelotas verdes, sólidos singulares de aspecto deformável e pegajoso, em peneiras de rolos por modelamento por aplicação de Método dos Elementos Discretos. Esta técnica mostra-se como uma importante ferramenta pois supera as limitações impostas na modelagem física (quantificação e identificação de fluxos por ausência de instrumentação em escala industrial, amostragem sem representatividade) ao reproduzir de forma verossímil as repostas do sistema para importantes variáveis de controle: comprimento de gap, umidade, dispersão de tamanhos e resistência das pelotas.

Oct 30, 2017