Search Documents

By Douglas Glenn Stalheim

Production of structural steel with a minimum yield strength of 700 Mpa produced as hot rolled coil has become increasingly popular due to cost considerations when compared to quench and temper equivalent product. This grade when produced as hot rolled coil requires the use of microalloy precipitation strengthening mechanisms. This is typically a combination of niobium and titanium microalloys. While the metallurgical concept of structural steel precipitation strengthening mechanisms has been well researched and published, actual implementation into the production process can be very challenging. In addition to achieving a minimum yield strength of 700 Mpa, in many applications additional mechanical property attributes of formability as measured by hole expansion testing along with low temperature toughness properties are now required. Achieving a balance of all the mechanical properties in a stable and repeatable performance in production using microalloy precipitation strengthening mechanisms further increases the challenges. This paper will discuss the metallurgical/process strategies required to successfully produce 700 Mpa minimum yield strength hot rolled structural steel coil. In addition, the role and goals of both niobium and titanium in this product design will be presented.

Oct 30, 2017

By Huang Qiming

The CISDI-GreenEAF innovatively applies the top-side-chute for charging for improving the cold zone of electric-arc furnace (EAF) requiring preheating scrap. It can greatly reduce the operating power consumption during EAF melting by combined use of fume for preheating scrap. The enclosed charging mode and specially-designed structure contribute to less emission of dust and fume during charging while enhancing the metal yield. Thanks to the extraordinary fume temperature control at scrap preheating procedure and fume quenching technology as developed by CISDI, for restraining the regeneration of dioxin.

Oct 30, 2017

By Eleir Mundim Bortoleto

A finite element modeling approach was developed to study adhesion phenomena during the unidirectional contact between a two-dimensional plane-strain square and a flat slab. Surfaces were metallic or ceramic, different pairs of materials were analyzed and their adhesion was considered by means of a FORTRAN subroutine (DLOAD), which was connected with commercial finite element code Abaqus and provided surface attractive forces based on the Lennard-Jones interatomic potential. Adhesive loads were considered both during approximation and separation of the surfaces. During the separation step, material transfer between surfaces, due to adhesion, was modeled by means of damage initiation and propagation at the flat slab. The parameters considered in the simulations were normal load, chemical affinity and system size and the different conditions were analyzed by comparison of the interaction forces during approach and withdrawal. This work also presents detailed descriptions of: (i) the evolution of energy dissipation due to adhesion hysteresis, (ii) the formation-growth-breakage of adhesive junctions and (iii) the evolution of stress distribution during the process. Results have indicated that chemical affinity between the bodies in contact is more relevant for adhesion than the applied load. Besides, smaller asperities are less prone to promote adhesive wear, but they may be subjected to high stress concentration effects.

Jul 31, 2018

By Bi Zongyue, ZhangYongqing, NiuTao, Guo Aimin

Over the past twenty years, significant advances have been made in the field of microalloying steels and associated applications, among which one of the most successful application cases is development and application of heavy-gauge X80 coil with high temperature processing HTP practice used for China's Second West-East pipeline, the longest X80 pipe in the world. During this process, HTP design concept has been sucessfully applied to develop 18.4mm X80 coil with demanding low-temperature fracture toughness requirements. In the meanwhile, China's metallurgical workers have further optimized HTP design concept with the aid of powerful rolling mill and coiling equipment, and made it possible to develop 21.4mm X80 coil used for Russia-China East line. In the paper, we would simply review the development history of high-strength pipeline steels, and then give more priority to the fundamental points for sucessful development of 18.4mm X80 coil and SSAW pipe, which paved the way for subsequent development of 21.4mm X80 coil and SSAW pipe. Finally, we would present the test results of mass production and burst tests, and dispel the suspicion that SSAW pipes made of X80 coil are more qualified to resist ductile fracture.

Oct 1, 2019

By Stefan Wahlund, Tom Adams, Mats Söder, Zhi Zhang

By applying high-end rolls with utmost performance and superior surface quality, hot strip mills can be further optimized. Operations in the mill have been also waiting for improved roll solutions that can minimize required roll changes which impact production efficiency. Limitations are usually due to the low performance and surface degradation of the rolls in the late finishing stands (F5 – F7). VICTURATM is the most recent developed grade for rolls utilized in the late finishing stand at Union Electric Åkers (UEÅ). These rolls have been tested and applied in mills all over the world. A significant improvement over the enhanced ICDP rolls has been observed. Hot strip mills are realizing improved operating efficiency and Total Cost of Ownership (TCO) through the transition of their entire roll inventories to these break-through products.

Oct 1, 2019

By Tiago Salzmann Vilela

No mercado de arames galvanizados destinados a indústria é exigida a uniformidade da camada de zinco sobre o arame. Neste trabalho, foram estudados os efeitos da velocidade de galvanização na uniformidade e espessura da camada de Zinco total, bem como a morfologia das fases de Zn e Ferro-Zinco sobre o substrato metálico. Verificou-se também o efeito do aquecimento após o processo de galvanização, observando o crescimento da camada intermetálica. Finalmente, serão mostradas as principais características de processo obtidas para garantir o atendimento aos ensaios de qualificação, em um estudo de caso de arames galvanizados produzidos em unidade industrial da Gerdau.

Jul 30, 2018

By L. Martins Demuner, D. Burzic, V. Cunha Aranda, F. L. Lourenço, G. Romeu Trindade dos Santos, F. Ramstorfer

For many years, Dynamic Soft Reduction has been regarded as a proper method in improving internal quality of slabs. Even though processes models improved significantly over the past years, the efficiency of Soft Reduction was always limited by the discretization error, which inherently exists if segment rollers cannot be positioned individually. The recently developed SRD segment type allows for an individual roller positioning within the mushy zone by avoiding any discretization deviation from the optimal gap. This paper provides a detailed technological overview of the SRD segments as well as operational results at their very first implementation at Ternium Brazil.

Oct 1, 2019

By Dyego Monteiro de Souza

This study compares the wear resistance of specimens lubricated with biofluids or mineral oil. Tribological studies were performed by ball-cratering test. In these tests were used as lubricants epoxidized soybean oil, castor oil and mineral oil. The specimens used were untreated and nitrided AISI 4140, while a steel ball AISI 52100 was used as a counterbody. In order to analyze the results obtained, the worn volume was calculated and the characterization of the crater, after the test, was made using optical microscopy and SEM. Wettability was also measured for the different surface condition and lubricants. As expected both specimens showed a smaller volume worn when lubricated with mineral oil due to inherent properties of this type of lubricant. Among the vegetable oils studied, the castor oil showed a better performance in the lubrication of the specimens untreated while on the nitrided specimen have shown less wear when lubricated with epoxidized soybean oil, indicating a difference in the efficiency of oils, as lubricants, depending on the surface conditions of the mechanical components.

Jul 31, 2018

By Fernando Ruiz Díaz

En aplicaciones a elevadas temperaturas como por ejemplo en cámaras de combustión y toberas de vehículos aeroespaciales se requiere el uso de aleaciones que permitan una elevada extracción de calor y buenas propiedades mecánicas. En este trabajo se realiza un análisis comparativo de las aleaciones Cu-Cr-Zr y Cu-Ag-Zr. Las mismas fueron sometidas a ensayos de resistividad eléctrica entre 25ºC y 700ºC y de tracción a 150ºC, 450ºC y 700ºC. Los resultados de los ensayos de resistividad eléctrica fueron convertidos a conductividad térmica mediante la relación de Wiedemann- Franz. A través de este análisis se observa que la aleación con mejor conductividad térmica es la de Cu-Ag-Zr presentando además un cambio de fase que no es observado en la aleación Cu-Cr-Zr. Respecto al ensayo de tracción la aleación Cu-Cr-Zr presenta mayores valores de resistencia a la tracción y tensión de fluencia a las temperaturas estudiadas.

Aug 16, 2017

By Rogério Felício dos Santos

Nitriding of metallic materials using electric discharges generated during electric discharge machining (EDM) is a recently developed technique. The aim of this paper was to correlate mechanical properties of a nitrided layer produced in AISI 4140 steel by EDM nitriding with the type and amount of nitrides. A conventional die-sinking EDM equipment and electrolytic copper electrodes were used to generate the electric discharges. The electrolyte was a solution of urea in deionized water. Knoop microhardness profiles assessed the variation of hardness along the nitrided layer, whereas the elastic modulus of this layer was measured using nanoindentation tests. Optical microscopy and X-ray diffraction (XRD) were used to characterize the nitrided surface. The results showed the formation of a nitrided layer containing iron nitrides with average thickness of around 25 µm. The amount of nitrides reduced from the surface towards the centre and these results correlated well with microhardness profiles obtained.

Jul 31, 2018

By Franco de Castro Bubani

Cu-base alloys (Cu-Zn-Al, Cu-Al-Be, Cu-Al-Ni), depending on their composition, have martensitic transformations that can be thermally or mechanically induced between a metastable structure called austenite and one or more metastable structures called martensites. In single crystals, depending on the specific composition of the alloy and the crystallographic orientation of the tensile axis, martensite-martensite transformations can be mechanically induced. The hysteresis associated to these martensite-martensite transitions is usually much greater than the one associated to the austenite-martensite transformation. Thus, martensite-martensite transitions are potential candidates for energy dissipation in a mechanical damper. Possible applications that would benefit from high hysteresis include seismic damping devices, dampers for satellites and the aerospace industry, defense and others. We present pseudoelastic cycling results of alloys submitted to different thermal treatments. Our conclusions highlight the fact that, under certain conditions, Cu-base alloys deliver better damping performance than commercially available SMAs and even the new Fe-base SMAs.

Aug 7, 2018

By Mario González Ramírez

The safe transport of sour gas requires steels with enhanced hydrogen induced cracking (HIC) resistance. Centerline segregation bands of high hardness microconstituents and non-metallic inclusions are the heterogeneities usually linked to HIC failures in pipeline steels. Full-scale production heats of a new low Mn, Nb microalloyed steel were produced by different steel mills aiming at the application in sour gas environments. The new alloy design provides both effective strengthening and control of sulphide inclusions. Coil microstructure consisted of fine grained ferrite with a small volume fraction of uniformly dispersed eutectoid aggregates. Most importantly the microstructure was uniform in both the longitudinal and transverse directions and exhibited exceptional consistency. Samples from this steel were submitted to HIC testing according to NACE standards TM0284-2003 without any sign of cracking. The results, so far, confirm that this new alloy design provides the unique opportunity to economically produce a high strength pipe steel grade with improved sour service resistance for the linepipe industry.

Aug 8, 2018

By Mühlböck Marlene

Increasingly stringent global environmental regulations are forcing steel producers to continually improve the efficiency of sinter waste gas treatment. With the Selective Waste Gas Recirculation (SWGR) system from Primetals Technologies, lower production costs can be achieved and the size of downstream waste gas cleaning units can be reduced for investment savings. SWGR features the extraction and reuse of hot sinter off gas from selected wind boxes along the sinter strand, which contributes to improved energy efficiency and off gas treatment in the sintering process. With the next generation of SWGR, Primetals Technologies can provide an energy optimized, emission optimized and environmentally friendly solution that meet customer requirements and country specific regulations. This paper demonstrates the latest developments in selective waste gas recirculation, especially results from pot grate tests and comparison from lab to real plant data. Furthermore theoretical finding and mathematical modelling is presented.

Aug 16, 2017

By Jianping Li, Fei Peng, Yunbo Xu, Jiayu Li

In this study, in order to achieve ultra-high strength without reducing plasticity, a novel heat treatment involving a pre-quenching process prior to conventional intercritical annealing (P-IDP) was proposed in a low carbon low alloy DP steel. It revealed that abundant fraction of banded structure was observed after conventional intercritical heat treatment (IDP) due to the inheritance of cold rolling deformation. However, the banded structure in novel heat treatment was eliminated significantly, whilst the refined microstructure was relatively more homogeneous with ultrafine ferrite grains. Moreover, obvious chain-networked martensite grains along the ferrite grain boundaries were obtained. The optimum mechanical properties with ultimate strength of 1238 MPa, total elongation of 17%, product of strength and elongation (PSE) of 21GPa% were obtained by P-IDP treatment, which was much higher than the values reported with similar composition. As to pre-quenching treatment, all of grain refinement, homogeneous distribution of martensite islands and precipitated strengthening of microalloyed carbides were beneficial to improve the final strength and ductility.

Oct 1, 2019

By Jorge Madias

Se analizan las distintas alternativas para la producción de barras de refuerzo de hormigón: endurecimiento por solución sólida (“dureza natural”); endurecimiento por temple y autorevenido en línea (Tempcore, Thermex, etc.) y endurecimiento por precipitación (microaleación con niobio, vanadio o titanio) y su influencia sobre la performance de las barras, en lo que hace a la resistencia a la corrosión, al fuego y a los sismos.

Aug 17, 2017

By Yuechang Wang

A new method of manufacturing the wavy-tilt-dam(WTD) mechanical seal has been mentioned. In this method, the special equipment is designed to provide a predetermined force to external and inner circular surface of the ring. After milling the end face of the seal by grinding miller and releasing the preload, the wavy-tilt-dam can be done on the seal surface. In this paper, a prediction model is built up to investigate the relationship between the predetermined force and the deformation on the surface of the ring by using ANSYS software. A WTD ring is manufactured by this method which approves that the prediction model is in accord with the real process and this manufacturing method of the WTD mechanical seal is a proper choice.

Jul 31, 2018

By Adriane Lopes Mougo

Super duplex stainless steel presents a biphasic structure composed by ferrite and austenite with different characteristics and properties. In the micromilling process the cutting edge radius has similar dimensions to the grain size. The biphasic structure found in this material could influence on the cutting tool life and the surface integrity of the workpiece. Due to its low machinability, caused by high hardening level and low thermal conductivity, the process can produce built-up edge and high surface roughness (Ra). In this work it is performed an experimental study of the micromilling of super duplex UNS 32750 and the influence of the cutting speed (Vc) and feed per tooth (fz) on the surface integrity and tool wear. The design of experiments considered two levels and three replicates. Results indicate the increase of roughness for bigger feed per tooth, small influence of the cutting parameters on the burr formation. The tool presented flank wear after the experiments.

Aug 8, 2018

By J. Bas A. F. Smeulders

Traditional laboratory lubrication tests, including those for cold rolling lubricants often involve measurement of neat oils. To achieve increased levels of test severity, such tests are often carried out at high temperatures and prolonged durations. However, we found that the levels of lubricant degradation and wear in these tests can be much higher than in the field. Moreover, steel rolling is not done with neat oils, but with emulsions, where the presence of water influences film formation, surface chemistry and oil composition in the roll bite. To better approach the situation in the field, and thus to be able to develop rolling oils with improved lubrication performance, several lubrication tests were developed for emulsions: direct measurement of film formation and measurement of Stribeck curves, in which the emulsions can be assessed in terms of their boundary lubrication and elastohydrodynamic behaviour. The key innovation is that also another test method was developed, which focuses on boundary lubrication and wear, and the role of extreme pressure and anti-wear additives. Realistic levels of test severity are achieved in the tribometer by mimicking frictional power intensities and flash temperatures for typical cold rolling or tinplate mills. Test conditions can be adapted according to the mill stand or pass number and other cold rolling process parameters. The emulsions are kept at normal operational temperature. Clear differences could be observed between emulsions of various concentration and composition. The viability of the method is illustrated by a number of field cases, in which a good correlation is demonstrated between the laboratory tests and the performance in a pilot or production mill.

Jul 30, 2018

By Humberto Tronconi Coelho

The use of friction dampers are wide proposed for a variety of mechanical systems for which it is not possible to apply viscoelastic materials, fluid based dampers or others viscous dampers. An important example is the application of friction dampers in aircraft engines to reduce the blades vibration amplitudes. In most cases, friction dampers have been studied in a passive way, however, a significant improvement can be achieved by controlling the normal force in the contact region. The aim of this paper is to study four control strategies for friction dampers based on three different hysteresis cycles. The first control strategy maximizes the energy removal in each harmonic oscillation cycle, by calculating the optimum normal force based on the last displacement peak. The second control strategy combines the first one with the maximum energy removal strategy used in the smart spring devices. Finally, is presented the strategy which homogenously modulates the friction force. Numerical studies were performed with these four strategies defining the performance metrics. The best control strategy was applied experimentally. The experimental test rig was fully identified and its parameters were used for numerical simulations. The obtained results have shown the good performance for the friction damper and selected strategy, also, the agreement between numerical and experimental results.

Jul 31, 2018

By Tobias Krull

The characterisation of iron ore from a materials handling point of view is paramount in order to provide the best possible design for the desired application and maximise equipment uptime at the lowest possible capital and operational expenditure. Problematic issues in materials handling applications often arise in the iron ore industry due to the high density of the ore as well as the abrasive nature of the product. One of the key issues encountered during the handling of iron ore is excessive wear due to either impact or sliding abrasion. The applications and equipment typically affected by accelerated wear issues are mass flow hoppers, transfer chutes and conveyor belts. These wear issues often result in unplanned down times and loss in production which can lead to a considerable loss in revenue. This paper provides an overview of the best practises in the materials handling characterisation of iron ore and discusses available techniques for the modelling of iron ore in applications where accelerated wear is experienced. The application is illustrated through a number of industry relevant case studies for which engineering design work was undertaken to successfully reduce the wear rates of different materials handling equipment.

Aug 1, 2018