Search Documents

By H. J. Rahilly

Mine fires, in the Butte district, have been a source of trouble and expense for the past thirty years, for while the actual fire area in most of the mines has been comparatively small, the handling of the gas has generally been a much larger problem than the actual putting out of the fire. The chief causes of these fires have been: Defective electrical equipment, incendiarism or carelessness, and spontaneous combustion. While fires from the first two causes have been numerous, they have generally been discovered and extinguished before they became very serious. Spontaneous combustion has been the cause of most of the large fires. Sufficient heat has been generated by ground movement, high rock temperatures, and decomposition to set fire to inflammable materials (tarred ropes, canvas, dry timber, manure, and hay) left in the gobs some years ago. Also, the heat resulting from the oxidation of the fine broken sulfide ore is sometimes sufficient to set fire to the timbers. In 1906, a fire was discovered on the 1100-ft. level of the Minnie Healy mine about 400 ft. (122 m.) west of the Minnie Healy shaft, which presumably originated, in one of the upper levels, from spontaneous combustion. The fire was walled off by concrete bulkheads and a pillar of ground 100 ft. (30 m.) thick was left below and mining resumed underneath. During subsequent operations, this pillar became cracked and broken and the fire passed into the new workings. It travelled downward and spread rapidly until, in 1917, it had become necessary to wall off portions of the Tramway, Leonard, and West Colusa mines on the 1300, 1400, 1500, 1600, 1800, 1900, and 2000-ft. levels, and the tops of the 2200-ft. raises were sealed. The fire area now consists roughly of a block 1000 by 1200 ft. and from the 600-ft. to the 2200-ft. level. This block is composed largely of a series of parallel northwest-southeast nearly vertical veins and stringers that form a large orebody, with no well-defined walls but badly fractured and faulted, and known locally as "horsetail ore." These veins, or orebodies, are mined by the square-set or the rill method.

Jan 1, 1923

By J. B. Newkirk

IN 1939 Bitter and Kaufmann1 suggested that iron, precipitating from a copper-rich, Cu-Fe solid solution, appears initially as coherent particles of r-Fe which transform to the body-centered-cubic form of iron when the alloy is cold worked. Since then there has been considerable discussion, supported only by indirect evidence, regarding the validity of the concept. For example, Reekie, Hutchison, and Hether-ington2 interpreted the changes in electrical resistance accompanying the aging of Cu-Fe specimens in terms of a coherent 7-Fe precipitate which transformed to the incoherent a-phase during long aging or cold working. Greninger- ound that Cu-Fe alloys which had been water quenched from 1050" and then held at 650°C for 3 hr changed from weakly to strongly ferromagnetic as the aged wire was subsequently cold worked. He also found diffraction lines corresponding to body-centered-cubic iron in Debye-Scherrer patterns given by aged and worked specimens but lines corresponding to only one face-centered-cubic phase in specimens which had been aged but not worked. Knoppwost,' and later Cech and Turnbull,5 found that aged Cu-Fe specimens showed a slight increase in ferromagnet-ism after they had be? cooled in liquid nitrogen. Very recently Denney6 followed the kinetics of the precipitation reaction as indicated by the saturation magnetization, hardness, and diffuse X-ray effects. The experimental results reported by all of the authors mentioned above are readily explained in terms of the Bitter and Kaufmann concept. However, most of the evidence is indirect when used to define the structural changes involved. It was the aim of the present investigation to determine the mechanism of precipitation of iron from a Cu-Fe solid solution in the light of available published information and with additional new and more direct experimental data. Experimental Method At 1060°C copper will contain up to 3 atomic pct Fe in equilibrium solid solution.7 The solvus slopes rapidly toward lower iron concentration, so that at 600°C only about 0.5 pct Fe remains in solution at equilibrium. Below the eutectoid temperature (850°C), the iron-rich phase in equilibrium with the copper-rich solid solution consists of body-centered-cubic a-Fe. Above 850 °C the equilibrium iron-rich phase is face-centered-cubic r-Fe. The alloy to be studied was made by melting electrolytic iron and OFHC copper by induction under vacuum in an Alundum-lined crucible. The metal was held molten for about 5 min, after which time the power was turned off and the crucible was tipped about 70" to promote directional solidification. The resulting ingot, containing 2.5 wt pct Fe by analysis, was clean, large grained, and free of gross segregation. Slices % in. thick were cut from the ingot, rolled to 1/8 in. in thickness, homogenized in hydrogen at 1060°C for 24 hr and, finally, quenched in cold water. Specimens for all subsequent tests were made from these slices. Squares measuring about 1 cm on a side were cut from the slices to make specimens for studying hardness and microstructure. Wires (0.020 in.) for the Debye-Scherrer survey were drawn from 1/8 in. sq rods which had been cut from the homogenized slices. Large crystals for observing diffuse X-ray diffraction effects were prepared by mechanically

Jan 1, 1958

HAVING told you of the practices of the arts involving other metals, I wish to tell you also of the practice of that of tin.* Indeed, since this is an easily melted metal, in common use for the utensils which are made for human needs, it is an art known not only to skilled men but also almost to children, wherefore I could proceed with- out telling of it. However, besides the production of plates and bowls and many other dishes for eating from and keeping things in, this embraces two other arts, both of which you should know about because they are useful and beautifid. One of these is the art .of making the letters with which books are printed, and the other is that of making the sheets from which organ pipes are built. The vessels, as perhaps you have seen, are cast one by one in moulds made of white tuff. Several pieces fastened together are then put on the iron axle of a wheel rotated by hand, and [138v] they are turned with a slightly bent tool which has a cutting edge. In this way they are made thin and of a good shape. Then they are polished with a piece of linen cloth and a little powdered tripoli, and thus they are finished. The letters for printing books are made of a composition of three parts of fine tin, an eighth part of black lead, and another eighth part of fused marcasite of antimony.t The desired quantities of these metals are melted

Jan 1, 1942

By Frank G. Snyder

INTRODUCTION Numerous deposits of lead and zinc sulfides, often accompanied by barite and fluorite, occur in carbonate host rocks throughout central and eastern United States. So similar are the deposits in broad general characteristics that they long have been classified as Mississippi Valley type. They differ widely, however, in details such as metal ratios, age of host rock, type of ore-bearing structure, and probable time of mineralization. The theories developed to explain the source and transport of the metals are many and are known to all. The deposits have been termed telethermal on the basis of their presumably shallow occurrence and the attempt to relate the metals to the classic hydro- thermal sequence. 1t is now recognized that deposits of this type can occur at any depth; the only depth limitation is thickness of the sedimentary section. Ideas on the source of the metals also have changed, A rapidly growing body of evidence suggests that the metals were brought by concentrated brines from nearby sedimentary basins. The hypothesis preferred today by many geologists postulates that the metals were deposited during the course of normal sedimentation in depositional basins of miogeosynclinal or orthogeosynclinal type. At some time after deposition of the sediments, the metals were carried out of the basins by migrating brines; the brines moved laterally and upward into structurally high areas; they entered any reservoir-like structure, either primary or secondary in origin, that happened to be available; in this reservoir, possibly in a sulfur-rich environment, the metals were precipitated as ore minerals.

Jan 1, 1970

By Arthur Taggart

Recent jig practice has shown such marked departures from the pronouncements of the textbooks, particularly as to particle size recovered and size range of feed, as to make it desirable to reexamine the mechanism of jig action. This paper presents the results of such a study. The general conclusions of the Paper are: I. A jig bed is a bi-functioned as well as bi-parted body. The upper layer comprises a plastic stream moving slowly in a substantially horizontal direction from feed lip to tail board. It serves to rough out tailing and light middling and to pick up heavy middling and lift it out 01 the jig box. The lower layer acts as the ultimate separating means by absorbing concentrate and rejecting heavy middling. 2. The separating function of the lower layer is performed in three definitely diflerent ways, depending upon the relative sizes of the grains presented to it and those composing it. Experimental The experimental work consisted of close and long-continued visual observations of operating beds in a plunger jig, eccentric driven, and in determinations of the settling rates of various metal spheres through a quartz bed under various conditions of operation. Falling velocities were measured by an ingenious method devised by A. 6. Dorenfeld, a student in the Mining Department at Colum- bia. Spheres of different metallic alloys, 3/8-in. diameter, were cast with a short piece of fine copper wire frozen in to Serve for suspension-A short piece of black cotton thread was looped to the top of the wire to serve as an indicator. The set-up for a test is shown in Fig. I. The thread should be boiled, if necessary, to make it freely water absorbent. The piece of clean plate glass D is supported rigidly at the proper height in a vertical position. The white scale E is similarly supported behind the glass. At the beginning of a test, D is filmed with water by holding it (best with clean rubber finger cots) under running tap water. It is then clamped in approximate position and C, already wet, is laid across it and drawn straight and vertical with the upper end at or near the top of D, and the ball A slightly above the top of the expanded bed. The water film holds the string to the glass. For a test the string is released, its upper end position noted just after the top of the ball becomes submerged, when the corresponding time is read, and thereafter simultaneous readings of position and time are taken as desired. Results of the visual studies of the bed are given at the pertinent places in the following discussion. Results of the settling tests are summarized in Figs- 2 and 3. Definitions The name bed as used herein refers to the entire mixture of solids and water filling the jig box. A layer is a stratum of a bed composed of particles of substantially the same specific gravities. A granular product is long-range when it approximates a crushed or ground product limited as to upper size only; a short-rafzge product is one closely sized. A bed is loaded when operating with continuous feed and discharge of products; it is unloaded when pulsating norma11y but neither being fed nor

Jan 1, 1943

By Arthur Taggart

Recent jig practice has shown such marked departures from the pronouncements of the textbooks, particularly as to particle size recovered and size range of feed, as to make it desirable to reexamine the mechanism of jig action. This paper presents the results of such a study. The general conclusions of the Paper are: I. A jig bed is a bi-functioned as well as bi-parted body. The upper layer comprises a plastic stream moving slowly in a substantially horizontal direction from feed lip to tail board. It serves to rough out tailing and light middling and to pick up heavy middling and lift it out 01 the jig box. The lower layer acts as the ultimate separating means by absorbing concentrate and rejecting heavy middling. 2. The separating function of the lower layer is performed in three definitely diflerent ways, depending upon the relative sizes of the grains presented to it and those composing it. Experimental The experimental work consisted of close and long-continued visual observations of operating beds in a plunger jig, eccentric driven, and in determinations of the settling rates of various metal spheres through a quartz bed under various conditions of operation. Falling velocities were measured by an ingenious method devised by A. 6. Dorenfeld, a student in the Mining Department at Colum- bia. Spheres of different metallic alloys, 3/8-in. diameter, were cast with a short piece of fine copper wire frozen in to Serve for suspension-A short piece of black cotton thread was looped to the top of the wire to serve as an indicator. The set-up for a test is shown in Fig. I. The thread should be boiled, if necessary, to make it freely water absorbent. The piece of clean plate glass D is supported rigidly at the proper height in a vertical position. The white scale E is similarly supported behind the glass. At the beginning of a test, D is filmed with water by holding it (best with clean rubber finger cots) under running tap water. It is then clamped in approximate position and C, already wet, is laid across it and drawn straight and vertical with the upper end at or near the top of D, and the ball A slightly above the top of the expanded bed. The water film holds the string to the glass. For a test the string is released, its upper end position noted just after the top of the ball becomes submerged, when the corresponding time is read, and thereafter simultaneous readings of position and time are taken as desired. Results of the visual studies of the bed are given at the pertinent places in the following discussion. Results of the settling tests are summarized in Figs- 2 and 3. Definitions The name bed as used herein refers to the entire mixture of solids and water filling the jig box. A layer is a stratum of a bed composed of particles of substantially the same specific gravities. A granular product is long-range when it approximates a crushed or ground product limited as to upper size only; a short-rafzge product is one closely sized. A bed is loaded when operating with continuous feed and discharge of products; it is unloaded when pulsating norma11y but neither being fed nor

Jan 1, 1943

JOSEPH W. RICHARDS, Chairman. J. E. JOHNSON, JR., Vice-Chairman. ARTHUR S. CALLEN, Secretary, 453 Chestnut St., So. Bethlehem, Pa. SUB-COMMITTEES IRON ORE DWIGHT E. WOODBRIDGE, Chairman. ERNEST F. BURCHARD, WILLIAM KELLY, CHARLES F. RAND, FELIX A. VOGEL. BLAST FURNACES II. A. BRASSERT, Chairman. WILLIAM H. BLAUVELT, AMBROSE N. DIEHL, JAMES GAYLEY RICHARD V. McKAY. STEEL WORKS HENRY D. HIBBARD, Chairman. GUILLIAEM AERTSEN, C. F. W. RYS, .1. S. UNGER. FRANK D. CARNEY, A. A. STEVENSON, WILLIAM It. WALKER. MECHANICAL TREATMENT CHARLES A. BUCK, Chairman. ROBERT W. HUNT, GEORGE MESTA, FREDERICK W. WOOD.

Jan 6, 1915

G. R. DELAMATER,* Steelton, Pa. (written discussion t)..-Under the heading, "Preparation of Coal," Mr. Campbell discusses the ad-visability of sizing the coal for the jigs. While I fully realize that conditions alter cases, my method at all times is to do everything possible to avoid sizing. It would be unwise for anyone to say that greater ash and sulfur reduction is impossible by sizing. The thing that can be questioned is, will the greater reduction be sufficient to counterbalance the greater cost? The same thing is true of the proper size of crushing for each individual proposition. In past years many washeries have been built and equipped for wash-ing two or more sizes, but I know of few instances where these plants were operated more than a year before sizing was abandoned. Perhaps in some of these cases this was clue to lack of sufficient development of such scheme of operation; yet I have found that most men engaged in this work, including myself, started into the work with a pretty well-fixed idea that sizing would be beneficial. But trials and tests showed that the mixed size washing is necessary for coals requiring crushing to 1 in. or less. Coal is of low value, compared with other minerals segregated by washing or concentration, for which reason simplicity must be the watchword: simplicity in the machine used to attain the separations of impurities from the coal, in the accessory plant equipment, and in its arrangement.

Jan 12, 1919

By H. J. Rahilly

MINE FIRES, in the Butte District, have been a source of trouble and expense for the past thirty years, for while the actual fire area in most of the mines has been comparatively small, the handling of the gas has generally been a much larger problem than the actual putting out of the fire. The chief causes of these fires have been: Defective electrical equipment, incendiarism or carelessness, and spontaneous combustion. While fires from the first two causes have been numerous, they have generally been discovered and extinguished before they became very serious. Spontaneous combustion has been the cause of most of the large fires. Sufficient heat has been generated by ground movement, high rock temperatures, and decomposition to set fire to inflammable materials (tarred ropes, canvas, dry timber, manure, and hay) left in the gobs some years ago. Also, the heat resulting from the oxidation of the fine broken sulfide ore is sometimes sufficient to set fire to the timbers. In 1906, a fire was discovered on the 1100-ft. level of the Minnie Healy mine about 400 ft. (122 m.) west of the Minnie Healy shaft, which presumably originated, in one of the upper levels, from spontaneous combustion. The fire was walled off by concrete bulkheads and a pillar of ground 100 ft. (30 m.) thick was left below and mining resumed underneath. During subsequent operations, this pillar became cracked and broken and the fire passed into the new workings. It travelled downward and spread rapidly until, in 1917, it had become necessary to wall off portions of the Tramway, Leonard, and West Colusa mines on the 1300, 1400, 1500, 1600, 1800, 1900, and 2000-ft. levels, and the top of the 2200-ft. raises were sealed. The fire area now consists roughly of a block 1000 by 1200 ft. and from the 600-ft. to the 2200-ft. level. This block is composed largely of a series of parallel northwest-southeast nearly vertical veins and stringers that form a large orebody, with no well-defined walls but badly fractured and faulted, and known locally as "Horsetail Ore." These veins, or orebodies, are mined by the square-set or the rill method.

Jan 2, 1922

By C. R. Claus, G. A. Standish

Since March. 1945, the Magnolia Petroleum CO. has drilled 39 wells in Southwest Coastal Louisiana. All wells were drilled within a comparatively small radius, but the area provides a large variety of problems. The deepest well drilled was 13,518 ft, and the total depth averaged 10,977 ft. Throughout this period drilling mud control and types of mud handled were: (I) phosphate, (2) red lime (late conversion), (3) red lime starch (early conversion), (4) red lime starch oil emulsion, (5) precision controlled low alkalinity-low lime content. and (6) gel muds for completion purposes. Improvement has been obtained in effecting some or all of the following: (I) more rapid penetration, (2) reduction in drilling hazards, (3) better evaluation of cores and logs, and (4) better completions. The geological sequence of zones penetrated range from recent sediments at the grass roots through the Frio section. Anticipation of high-pressure zones and incompetent formations entails precision control of drilling mud weights, and the unconsolidated nature of the various zones requires constant attention to the filtrate, viscosity, and gel strength values. In the Chalkley field, particularly, this combination of problems exists, where the formation pressures and overburden weight density values are in very close proximity. Design of casing and drilling mud programs must be modified to fit each well. INTRODUCTION Field and research work on drilling fluids has made constant progress, enabling operators to prospect progressively deeper horizons. Numerous papers have been written on the theoretical aspects of drilling fluid devel- opment, but in the field engineers have found it difficult to evaluate the role of specific mud constitutents when dealing in terms of thousand barrel mud systems. For that reason field data is somewhat lagging in technical report writing. However, applications of new techniques in the field have usually paralleled, and in numerous instances preceded, research work. The information obtained by Magnolia Petroleum Co. in the course of drilling 39 wells within a comparatively small area in Southwest Coastal Louisiana provides an excellent opportunity of reviewing a specific example of drilling mud evolution. A large variety of problems has been coped with, the most important result being that every well was successfully drilled to its projected total depth. The discussion begins with the advent of deep drilling in this area in March, 1945, and is concluded with a resume of recent drilling operations in the Chalkley field. The primary purpose of this paper is to describe the evolution in types of drilling fluids as it occurred and its application in the solution of various drilling problems. All of this information and experience resulted in the successful drilling of the three wells in the Chalkley field, where a combination of the most sound techniques was necessary in carrying drilling operations to the projected total depths. Other operators along with service company engineers have contributed considerably through the interchange of ideas and information to this paper, but the data and conclusions which are contained are based on first-hand observation of Magnolia Petroleum Company's drilling operations. The 39 wells drilled by Magnolia Petroleum Co. average in depth 10,977 ft per well, while the maximum depth penetrated was 13,518 ft. The cost of drilling fluids have varied from $8,700 to $165,000, with the over-all drilling costs ranging from $74,000 to $543,000 per well. This wide variance illustrates the unpredictable nature of each well and the effects on over-all cost when high density muds are required to control

Jan 1, 1955

By David J. Mack, T. V. Philip

The effects on the Cu-A1 eutectoid transformation of the addition of a third element from the second long period and from Group IIB of the periodic table, were studied by isothermal transfomation techniques. The valency of the third element shows the most pronounced effect on the eutectoid decomposition. With some exceptions, the atomic size factor of the third element shows some consistent effects on pearlite nucleation and growth. The atomic concentration or the electronegative valency of the third element shows wo consistent effect on the eutectoid decomposition. Addition of the third element helps spheroidization of pearlite. SINCE the pioneering work of Davenport and Bainl on the eutectoid decomposition in steel by the isothermal transformation technique, an enormous amount of data has been accumulated on the eutectoid transformation characteristics of commercial steels. While the eutectoid reaction in steel is of tremendous industrial importance, it appears to be quite unique among the eutectoid reactions. Though the metal-lographic structures developed in the Fe-C and Cu-A1 eutectoids are similar, it is now evident that the two eutectoid reactions are quite dissimilar. The eutectoid decomposition in the Cu-A1 system is more complicated partly due to the appearance of transitional phases in addition to the equilibrium phases. * The first isothermal studies of aluminum bronzes were made by Smith and Lindlief2 and later by Mack,3 Klier, and Grymko,4 and recently Hayne 5,6 A few other systems, structurally analogous to the above, have been studied by the same technique.7-10 Kasberg and Mack1' studied the effects of iron on the transformation of commercial aluminum bronze. The effects of manganese and nickel on this aluminum bronze and those of iron, manganese, and nickel on the binary Cu-A1 eutectoid have been recently studied.12 The object of the present investigation was to study, by isothermal transformation techniques, the effects (with respect to the fundamental factors of alloy formation) of the addition of a third element on the transformation of a Cu-Al eutectoid alloy, 11.8 pct Al. The third elements chosen for the purpose were silver, cadmium, indium, tin, and antimony from the second long period, and beryllium, zinc, and cadmium from group 11B of the periodic table. They were added in nominal amounts of 0.5, 1.0, and 2.5 pct by weight to a eutectoid Cu-A1 alloy. These third elements were expected to show the effects of electron valency, atomic size factor, and electronegative valency effects on the binary eutectoid transformation. PFLEPARATION OF ALLOYS AND PROCEDURE All alloys were made as 400-g heats by induction melting in a graphite crucible with a graphite lid. The molten alloy with a layer of graphite powder on top was stirred at regular intervals by a graphite rod. When the melt was judged to have acquired sufficient superheat, a pinch of common salt was sprinkled on top and any crust scraped off to one side. It was then chill cast into a 5/8 in. rod. The alloys with silver were prepared by remelt-ing the high-purity Cu-A1 eutectoid alloy used by Mack3 with high-purity silver (99.99 pct pure from Hardy and Harmon, Inc.). In the preparation of all the other alloys, polished electrolytic copper shot (from Belmont Smelting and Refining Co.) and high-purity aluminum (99.99 pct pure from Aluminum Co. of America) were used.

Jan 1, 1962

By B. D. Smith, K. H. Coats

Experiments in which calcium chloride displaced sodium chloride from four cores showed the extent of asymmetry in the resulting effluent concentration profiles. These results provided a check on how validly the mixing process is modeled by a differential (i.e., not finite-stage) capacitance mathematical model. The effluent concentration profile from two consolidated cores exhibited considerable asymmetry, while two unconsolidated cores yielded nearly symmetrical profiles. All runs resulted in breakthrough of the 50 per cent concentration significantly before one pore volume was injected. In addition, velocity appreciably affected the effluent concentration profile from a Torpedo sandstone core. The differential capacitance model matched the data significantly better than a simple diffusion model. The capacitance model allows determination of the amount of dead-end pore space in a porous matrix and the effect of velocity on the rate of diffusion into this space. An experimental program yielding insight into the physical validity of the capacitance effect is described. INTRODUCTION Axial dispersion — the mixing accompanying the flow of miscible fluids through porous media — has been the subject of many relativeiy recent studiesl-13 and a comprehensive review of the topic has been given by Perkins and Johnston.14 This dispersion is of practical interest in studies of the miscible displacement process, fixed-bed chemical reactors, and the adsorption of solutes from a flowing stream onto the surface of a porous medium. In the latter case, the effect of dispersion must be considered when adsorption parameters are determined from the nature of concentration profiles. In general, early studies of dispersion assumed applicability of a simple diffusion equation and were concerned with correlation of the experimentallv determined "effective" diffusion coefficient with system properties over a large range of the latter. Recent have been concerned with the deviations between the asymmetrical effluent concentration profiles observed and the symmetrical ones predicted by the diffusion model. In the present study, effluent concentration profiles were obtained from consolidated and unconsolidated cores. These profiles were compared with those predicted by a differential (i.e., not finite-stage) capacitance model. Solutions to the simple diffusion model, for three sets of boundary conditions, were compared with one another and with the experimental profiles. SUMMARY OF PREVIOUS WORK The reader is referred to Perkins and johnston14 for an extensive review of studies of dispersion in porous media. Many investigators have employed the simple diffusion model characterized by Eq. 1 below: The dispersion coefficient D for unconsolidated systems is correlated by u is interstitial velocity and dp is particle diameter. Since heterogeneity of the sand pack affects the mixing, this equation is also expressed as where a is proportional to the degree of heterogeneity and is about 3.5 for random packs of unconsolidated sand.l4 Eq. 3 holds for 2 For a Do homogeneous (regular) type of packing, should be 1 or less.6 Aris and Amundson6 and Carberry and Bretton consider o to be the number of particle lengths per mixing cell in the finite-stage model. Data from consolidated cores indicate dp to be about 0.36 cm for outcrop rocks, Torpedo sandstone having a reported value of 0.17 cm.15 For v /Do less than about 2, the effect of molecular diffusion must be considered and the total dispersion coeffi-

Jan 1, 1965

By C. S. Smith, L. H. Beck

KNOWLEDGE of the Cu-Zn constitution diagram was critically examined in 1944 by G. V. Ray-nor,1 who suggested the diagram reproduced in Fig. 1 as the best evaluation of available data. No pertinent work on the constitution has been published since that time, although a number of authors have discussed transformation kinetics and theory. Despite the large amount of work that has been done on the constitution of these industrially important and scientifically interesting alloys, minor uncertainties still exist. For example, it is still not possible to say definitely whether a two-phase region exists between the ordered and disordered forms of the 8 phase. A careful re-examination of the phase boundaries in this part of the diagram was therefore undertaken. Two methods were selected for the new investigation—quantitative metallography for the higher temperatures and precision lattice parameter measurement for lower temperatures. Because of the relatively narrow two-phase regions flanking the ß phase in these alloys, quantitative metallography is particularly suited for their examination, since the relative amounts of the two phases are very sensitive to their compositions. The method, however, is useless below about 350°C because of the inadequate resolution of the two constituents. Below 400°, however, the X-ray diffraction method is applicable, although it is of somewhat lower sensitivity in this system. The changes of composition that occur during quenching from above about 500°C entirely vitiate X-ray measurements at room temperature though they do not affect metallographic area measurements. The two methods overlap and supplement each other admirably. Both methods depend on the attainment of equilibrium composition of the two phases in a more or less intimate mixture and thus avoid the difficult problems of nucleation and long range diffusion involved in the conventional metallographic bracketing method. The alloys were melted from a master alloy made from re-electrolyzed cathode copper and Horsehead 99.99 pct Zn. Melting was done under a cover of either borax or charcoal and the alloys cast into a 7/8 in. sq graphite mold for the a-ß alloys or a 3/8 in. diam cylindrical graphite mold for the ß-? alloys. The a-ß alloys were rolled at 750°C to 5/8 in. sq; annealed for 24 hr at 800°C and quenched; then rolled and swaged at 200°C to 3/8 in. diam rods, annealed 24 hr at 200°C, quenched and cold rolled 2 pct reduction. This treatment was intended to obtain a small grain size and to produce many nuclei of the minor phase for growth on subsequent heat treatment. The unworkable ß-? alloys were given preliminary treatment by sealing in Vycor tubes in vacuum and annealing for 4 hr at 800°C followed by cooling in air. Samples of homogenized alloys were checked spectrographically for impurities, but the principal components were determined on samples subsequent to heat treatment. The impurities analyzed averaged approximately as follows: Ag, 0.0002 pct; Fe, 0.004; Si, 0.0008; Cd, 0.005; Mg, 0.0002; and Pb, 0.002. For metallography, samples of appropriate composition were cut into rods 5/8 in. long, sealed in pyrex tubes in vacuum and annealed for eight weeks at temperatures of 470°C and below, two weeks at 480°, 500°, and 600°C, and 4 hr at 700°C, followed by quenching in cold water. Temperatures were accurate to ±2°C. The cylinders were then machined to 8.7 mm diam and a slice weighing 1.5 g cut with a thin saw transversely from the center of each. This

Jan 1, 1953

SEC. 1. The membership of the Institute shall comprise seven classes, namely: 1. Members; 2. Honorary Members; 3. Senior Members; 4. Associates; 5. Junior Members; 6. Rocky Mountain Members; 7. Junior Foreign Affiliates. All shall be equally entitled to the privileges of membership, excepting that no member of any class whose residence shall be outside of the United States of America, except those residing in Mexico and Canada, shall be entitled to vote. SEC. 2. Members: A person to be eligible for election or transfer into the class of Member must be at least 27 years of age and must have had at least six years' employ¬ment in the practice of engineering, mining, geology, metallurgy, or chemistry, during at least three years of which he must have held positions of responsibility in one or more of these fields. This shall not apply to Rocky Mountain members. SEC. 3. Honorary Members: Each candidate for Honorary Membership must be recommended by at least ten Members and must be elected by ballot at a meeting of the Board of Directors by the unanimous vote of the Directors present; provided, how¬ever, that the number of Honorary Members shall at no time exceed twenty. Such election shall automatically act as a transfer of such member from any other class of membership to which he may belong. SEC. 4. -Senior Members: The Directors may in their discretion place on the Honor Roll of Senior Members and transfer from any other class of membership other than Honorary Membership the name of any Member or Associate who has reached the age of seventy years and who has paid dues for thirty years, and for good reasons in special cases may vary the age or number of years. SEC. 5. Junior Members: A person to be eligible for election to the class of Junior Member must be qualified through education or experience to hold a subordinate position in engineering, mining, metallurgical, geological or chemical work. He shall be not more than 33 years of age at the time of election. SEC. 6. Associates: A person eligible for election or transfer into the class of Associate shall be one, who, in the opinion of the Committee on Admissions and the Board of Directors, is suitable for such election or transfer by reason of his interest in or connection with mining, geology, metallurgy, or chemistry. SEC. 7. Rocky Mountain Members: Membership in a special class of life member¬ships without annual or other dues and without right to receive the printed literature distributed to other members or the right and privilege of wearing the official badge of technical members, is given to all members of the Rocky Mountain Club at the time of consolidation. These special Rocky Mountain memberships shall be claimable by any member of the Rocky Mountain Club, not already a member of the Institute, availing himself of the privilege within ninety days after mailing of notice to him, by the Secretary of the Institute. SEC. 8. Junior Foreign Afliate: Upon appropriate action by the Board of Direc¬tors and with its approval, members in good standing of any technical society having its headquarters outside of the United States of America, Canada, or Mexico,

Jan 1, 1937

Edward Halse, Puerto Berrio, Colombia, S. A. (communication to the Secretary): I have read with much pleasure the interesting and valuable paper by Mr. Kunz, and hope that the following brief notes, gathered a few years ago, while a resident in Mexico City, may help to elucidate the subjcct: Turquoise.—This was known to the Aztecs as Xihuitl. Santiago Ramirez states that they found it in the Cerro Xicohtzonc, close to Atzcapatzalco, a suburb of the City of Mexico (compare page 59). Opal.—This was known to the ancient Mexicans, for they named it mezcuitlatt (compare page 63). Jade.—Under this was iucluded a third mineral, prehnite, not mentioned by Mr. Kunz. According to James D. Dana, part of the "jade " of China is prehnite; and Humboldt informs us, in his work on New Spain, that the same species of jade is known in some parts of Mexico as mahagua (majagua ?). The same writer says, in his Views of the Cordilleras, that the Aztec name Tecpatl included flint, hornstone, and green jade; and finally, in his Travels in South America," he discusses the nature of the ancient amazon-stones, and declares them to have been made out of a jade resembling " compact feldspar," one of the constituents of the gabbro verde di Corsica. IIence those stones were probably composed of nephrite. According to Humboldt, the form given to them most frequently is that of the Babylomian cylinder, longitudinally perforated, and loaded with inscriptions and figures. They were also cut by the natives into very thin plates, perforated at the center, suspended by a thread, and worn as amulets. According to the historian Clavijero, the specific name given by the Aztecs to the nephritic stone (jadeite) was Quitzalitztli,

Jan 1, 1902

By B. Wilhelmi, W. H. Somerton

Simultaneous measurement of pore and elastic properties of socks under a wide range of triaxial stress conditions may be made with equipment and methods developed in this paper. Tests were run on three outcrop sandstones at several confining pressures and axial stresses up to approximately 80 percent of failure stress. The greater reduction in porosities and permeabilities occurred in the hydrostatic loading portion of the stress cycle, but substantial reductions in both properties did occur upon application of deviator (triaxial) stress. Triaxial elastic moduli were calculated from strain gauge measurements. Both Young's moduli and shear moduli were found to increase with increasing confining pressure. Poisson's ratios increased with axial stress but showed no consistent change with confining pressure. Only very general relations were observed between pore and elastic properties. The lesser decrease in porosity and permeability at higher stress values is related to increase in rigidity of rocks at higher stresses. INTRODUCTION Many investigators have studied the effects of hydrostatic stress on the properties and behavior of rocks. A few have studied the effects of triaxial stress fields on individual physical properties of rocks. To our knowledge no one has measured simultaneously pore and elastic properties of rocks under a wide range of triaxial stress conditions. This is the purpose of this work. Rocks exist in the subsurface under what Jaegerl refers to as "polyaxial" stress conditions (all principal stresses unequal). When two of the three principal stresses are equal, this is referred to as triaxial loading. The triaxial method of loading is most commonly used in modern testing work because experimental difficulties in measuring physical properties of rocks are greatly reduced over polyaxial testing. Although triaxial loading may not reproduce subsurface conditions precisely, subsurface stress conditions are never known precisely anyway. Triaxial testing would seem to be more realistic than testing under hydrostatic loading (all principal stresses equal) for application of results to subsurface problems. The objectives of this work were threefold: (1) to develop methods of measuring simultaneously pore and elastic properties of rocks under triaxial stress conditions, (2) to determine whether changes in these properties are of sufficient magnitude to be considered in subsurface calculations and (3) to attempt to relate changes in pore properties and elastic properties since they will have been measured at the same time under identical loading conditions. REVIEW OF EARLIER WORK PORE PROPERTIES Several investigators have studied the effects of stress on the physical properties of rocks. Fatt and Davis2 showed the reduction of permeability of rock with hydrostatic loading. McLatchie et al.3 and Knutson and Bohor4 related permeability reduction to compessibility of reservoir rock, again under hydrostatic loading. Wble,5 and later Redmond,6 evaluated the effects of applied radial pressure on conductivity, porosity and permeability of sandstones. In this latter work, no axial stress was applied. Dobrynin7 reviewed much of the previous work done . on the effects of overburden pressure on physical properties of rocks. He concluded that changes in physical properties are controlled to a large extent by pore compressibility of the rock. Several sets of curves developed from empirical relations are presented. These curves permit estimation of change of properties with net overburden pressure, knowing the pore compressibility and porosity of the rock. Net overburden pressure is defined as (Pe - 0.85 Pi ) where Pe is the

By James T. Waber, Allen C. Larson, Karl Gschneidner, Margaret Y. Prince

The original graphical method proposed by Darken and Gurry for predicting which elements are soluble in a given element was slightly modified and was used to predict terminal solubilities in 1455 known binary combinations. it was found that the modified Darken and Gurry method had a reliability of 61.7 pct in predicting extensive solid solubility (greater than 5 at. pct) and of 84.8pct in predicting limited solid solubility (less than 5 at. pct), an over-all reliability percentage of 76.6. Using the same experimental data, it was found that using only the simple Hume-Rothery size-effect criterion was 50.1 pct reliable in predicting extensive solid solubility, only slightly better than a purely random choice. and 90.3 pct reliable for predicting limited solid solubility, an over-all reliability percentage of 67.6. THE first rational rules for determining a priori whether two metals are not freely soluble in the solid state were announced by Hume-Rothery and coworkers.1,2 These well-known rules have been accorded a special place in metallurgical literature. Since the "electronegative" and "relative valence effect" rules of Hume-Rothery were only qualitative in nature it was difficult to use them in a quantitative analysis. The next major step was made by Darken and gurry3 and apparently went unexplored for a number of years. They prepared graphs illustrating the influence of both electronegativity and size difference on the solubility of elements in silver, magnesium, and aluminum, and they drew elliptical figures, whose maximum width was ±15 pct of the solvent radius and the maximum height was ±0.4 electronegativity units. The purpose of the present paper is to assess and compare the effectiveness of using the simple size-factor and the Darken-Gurry criteria to predict which elements will be soluble and insoluble in a given solute. In 1957, waber4 prepared Darken-Gurry plots for determining the solutes that were likely to be soluble in 6 and plutonium and introduced an inner ellipse as an aid to determining which elements should be soluble to a considerable extent. As illustrated in Fig. 1, the major axis of the outer ellipse corresponded to ±0.4 electronegativity units (OD) while the minor axis corresponded to ±15 pct of the radius of the solvent phase (OB). This simultaneous "action" of the two Hume-Rothery criteria was used to indicate which elements would have little or no solubility in the host lattice, namely those elements whose points lay outside this ellipse. An inner ellipse, "centered" over the same point of the solvent was drawn with ±0.2 electronegativity units (OC) and ±8 pct (OA) as the major and minor axes. Solutes with points lying within the inner ellipse were expected to be capable of forming extensive solid solutions with the host element. Use of this method of applying the earlier Hume-Rothery criteria was moderately successful for plutonium. For 6-phase plutonium, only one element out of the eight predicted to be extensively soluble was known to be almost insoluble, and of the sixteen elements predicted to have more restricted solubility, five were known to be essentially insoluble. The success of discerning solubility in the E phase by this method was comparable. One prediction made on the basis of this analysis was that the heavier rare earth metals, such as holmium, erbium, and thulium, should be soluble in the 6 phase, whereas the lighter rare earth elements, such as lanthanum or

Jan 1, 1963

Curiously enough, considering the relative accessibility of the two places, coal was reported at an earlier date in Saskatchewan than in British Columbia. Henry and Thompson were on the Saskatchewan River in February 1811, and on the 4th of that month recorded, while on Jack's Branch of North Brook, "I observed in one of the bends on the north side a bank of yellow clay, on which there appeared several horizontal veins of pure coal, of the best quality I have seen along this river." Later at Rocky Mountain House it was said: "a quantity of coal is tumbling into the water, as the current washes away the earth underneath. This coal abounds along the Saskatchewan, in some places forming solid beds several feet thick for several acres, which are washed by the river. In its pure state our smiths use it for the forge with equal proportions of charcoal made of birch or aspen, which answers every purpose for making and repairing our axles and other tools."1 It is needless to say that it was many years before this coal was used for any commercial purposes. Coal was first found on the northern end of Vancouver Island in British Columbia in 1835 at Beaver Harbor, where later Fort Rupert was established, where Indians had advised some of the Hudson Bay Company officials it would be found.2 The coal was used by smiths, and later on by the steamer plying along the coast.3 A report to the government in 1845 called attention to the coal reported in the neighborhood of Puget Sound and on the Cowlitz River, and that probably the samples used by the Hudson's Bay Company were obtained from the surface and. were not good. On September 7, 1846 a report on the coal situation was submitted by Ogden and Douglas, and a naval vessel was sent to investigate the report and was loaded with 62 tons dug out by the Indians, the seam outcropping along the shore.2 In 1847 some samples were sent to England by a returning war vessel. In 1849 the Hudson's Bay Company established a

Jan 1, 1942

By D. W. Fuerstenau

Recently R. J. Charles1 showed that comminution of brittle or semi-brittle materials in batch operations is described more appropriately by a variable energy relationship than by the specific relationships proposed by Rittinger,2 Kick,3 and Bond.' That is, the value of n in the empirical differential operation which applies to crushing and grinding (Eq. 1) is variable. Independently, Holmes' developed an identical generalized equaton for size reduction. The experimental data of Charles and Holmes show that the value of n is determined by the material and the comminuting machine and is constant for a given combination of these two conditions. The general objective of the present article is to extend the Charles-Holmes concepts to continuous ball milling. The specific objective is to analyze the operation of a vibratory ball mill dry-grinding chromite in a continuous open circuit and to develop an equation for the comminution of chromite in this mill. Basic Principles: In a batch mill the length of time during which the material is ground is a direct measure of the energy expended on the material, except possibly for exceedingly fine grinding. However, in a continuous operation, the fraction of the total expended energy which is useful for grinding will vary according to feed rate and amount of material in the mill. If the amount of material within a continuously operating vibratory mill is low enough so that only part of the expended energy is used for grinding, the extent of size reduction at constant power input must depend upon the length of time the material is retained within the mill, namely, upon retention time. The following analysis pertains to a continuous mill operating under these conditions. The empirical differential equation that applies to the comminution of brittle materials is:" dE = -Cdx/x" [1] where dE is an infinitesimal energy expenditure, C a constant, dx an infinitesimal size change, x the particle size, and n a constant. For continuous grinding in an open circuit at constant power input, P, Eq. 1 must be written as (dtr)P = -C dx/x" [la] where dt, is an infinitesimal time during which a particle of size x is in the mill, and C' is a constant. A ground product never consists of particles of single size but always comprises a distribution of sizes. In comminution, the expenditure of energy causes a lateral shift in the size distribution.', ' " The general objective of any engineering study of comminution is to correlate the magnitude of this size distribution shift with the energy expended, the ultimate aim being to cause the greatest shift with the least amount of expended energy. Although a number of criteria can be used to measure this shift, Schuhmann's size modulus has been found convenient.' Mathematically, the Schuhmann size distribution can be expressed as follows:" y = l00(x/k) [2] or in differential form: dy = [F- xa-' dx ] K, where y is percentage of material finer than size x, a is a constant that determines weight distribution among particles of various sizes, and k the size modulus that denotes the theoretically maximum-sized particle in any size distribution. By considering the energy required to reduce an element of weight of material, dy, from size x, to size x, the element of time during which the material must remain in the mill at at power will be (dt..).= J'-Cax!(dy) [3] Summing up all the elements of weight from zero to 100 for a product that conforms to the Schuhmann size distribution yields C C f Cdx,\( 100«x°-'dx\

Jan 1, 1960

By Roscoe C. Clark

A study of the effect of various corrosive waters on five different types of cements indicated that those cements containing less than 5 per cent tricalcium aluminate were the most resistant to corrosion. INTRODUCTION Oil field experience indicates that some formation waters are excessively corrosive to some cements. A study has been made to determine the most corrosive waters and the relative resistance of various types of cement to these corrosive waters. PROCEDURE This study of the corrosion of cement was limited to an evaluation of the effect of various corrosive waters on five different types of cements. A determination was made of the types of cements which offer the greatest resistance to corrosion and of the chemical contents of waters found to be the most destructive to cements. The laboratory tests were conducted by immersing small cylinders of 20 samples of set cement in various corrosive waters. The initial mixing of most of the cement slurries was done using Tulsa tap water as the mixing water; however, a few of the slurries were mixed using a sulfate water as the mixing water. When the 20 samples had been immersed for a period of nine months, they were removed from their corrosive baths, inspected and photographed. The field tests were conducted by placing ten cement specimens, each contained in a screen wire thimble, in the gas anchors of insert pumps in wells in six different fields. The specimens were observed whenever it was necessary to pull the pumps and were returned to the 1aboratory when deterioration had reached a serious state. EXPERIMENTAL RESULTS In both the field and laboratory tests the resistance of the different cements to corrosion was determined by the condition of the samples and the number of samples of each that were in good condition at the end of the immersion period. Table I lists the various cements tested in the order of their resistance to corrosion with the most resistant at the top and the least resistance at the bottom. An analysis of Table I reveals that the upper half of the table predominates in slow set and sulphate resisting cement.: (low 3CAO.A12O3 content) while in the lower half the port-land and high early strength cements are in the majority. Of the last two the high early strength cements appear to offer less resistance to sulfate water corrosion. An investigation of the composition of the cements listed in Table I indicated that as a general rule the cements containing less than five per cent tricalcium aluminate will exhibit the greatest resistance to corrosion. The destructive action of various corrosive waters was compared by listing the waters in the order of those containing the largest number of samples that failed completely. These ratings are presented in Table II with the most corrosive waters listed first and the least corrosive last. Figs. 1 and 2 show the end views of cement samples which had been immersed in the baths of five per cent MgSO, water and the five per cent Na2SO4 water respectively in the laboratory. These .pictures are representative of the results obtained and present a pictorial evaluation of the corrosive resistance of various types of cements.

Jan 1, 1950