Search Documents

By G. Bruggeman, K. G. Kreider

Grain boundary dij]usion coefficienls were measured in tungsten between 1400° and 2200° C and can be expressed by the equation sq cm per sec This activation energy confirms some eavlier estimates made .from tungsten sintering experiments. Grain boundary diffusion was found to occur in sub-bozrndavies having -misorientations of less than 10 deg. The actiuation energy for this subboundavy diffusion is equal to that for dijjusion in incoherent grain boundaries with in the limits of error. This is shown to be consistent with the dislocation model of Low-angle boundaries wheve diffusion occlcvs along- the dislocation 'YPipes" comprising -tile boundary. RECENT investigations of the sintering of tungsten powders all report activation energies which are considerably less than the activation energy for tungsten volume diffusion. Kothari' reports a value of 100 * 5 kcal per mole, Hayden and Brophy' obtained 90 kcal per mole, and Vasilos and smith3 found 110.7 kcal per mole from their sintering studies. Since most determinations of the activation energy for volume diffu-sion4-' fall between 120 and 160 kcal per mole (the true value seems most likely to be nearer 150 kcal per mole), the conclusion is drawn that the mass transport leading to densification during sintering is accomplished by grain boundary diffusion. This interpretation is consistent with various diffusion models of the sintering process. 10-12 Vasilos and Smith calculate diffusion coefficients from their data which fit the equation D * 1.36 x 10* exp(-llO,700/HD However, no direct measurements of tungsten grain boundary diffusion have been made. Furthermore, considerable disagreement exists between the directly measured values of tungsten volume diffusion.'-' In order to corroborate the inferred results of the sintering experiments concerning grain boundary diffusion and to provide accurate diffusion data essential to the analysis of the kinetics of creep, oxidation, precipitation, and so forth, the present work was undertaken to measure self-diffusion in single-crystal and polycrystalline tungsten between 1400" and 2200°C. It is within this temperature range that tungsten sintering is done, the re crystallization of tungsten occurs, and the widest application of tungsten as a high-temperature material will probably be made. EXPERIMENTAL PROCEDURE Radioactive WlE5 was produced by irradiating tungstic acid in a neutron flux of 1.2 x 1012 neutrons per sq cm per sec for 36 hr. A 2-week waiting period was allowed for the decay of w"~ also produced by the irradiation. (w"~ has a half-life of 24 hr.) The half-life of the remaining isotope was determined to be 75 days confirming the presence of w lE5 and the absence of any undesired radionuclide. Specimens 4 in. in diam and $ in. thick were cut from polycrystalline swaged tungsten rods (recrystal-lized) and from Linde single-crystal rods. Chemical analyses of these materials appear in Table I. Actually upon closer examination, the single-crystal specimens were found to consist of several subgrains separated primarily by tilt boundaries in which the misor-ientation ranged from 3 to 10 deg. Thus, it was possible to measure boundary diffusion coefficients in these low-angle subboundaries as well as in the incoherent boundaries of the polycrystalline specimens. The two faces of each specimen were ground flat and parallel within 0.0001 in. The radioactive tungstic acid was dissolved in concentrated ammonium hydroxide, placed on the ground flat of the specimen, and evaporated to dryness. The oxide was then reduced in hydrogen at 1000°C resulting in a layer of wlE5 approximately 1 p thick. The diffusion anneals were performed in vacuum in a tantalum resistance furnace. Time at temperature ranged from 10 hr at 1400°C to 2 hr at 2200°C. The penetration profile was determined by measuring the residual activity after successive removal of surface layers by grinding on metallographic polishing paper. Extreme care was exercised to insure that sections were always taken normal to the diffusion direction; this was verified repeatedly by checking that front and back surfaces of the specimen remained parallel. The activity was measured with an end-window Geiger-Mueller counter. The sides and edges of the specimen were well-shielded to eliminate possible effects due to surface diffusion. The weight of the

Jan 1, 1968

By G. W. Tracy, R. D. Carter

Numerical calculations were made to determine the behavior of reservoirs with high-pressure drawdown and wide well spacing where the initial productivity is low and the wells are completed by hydraulic fracturing. The two-phase flow equations were solved for the flow into a single well. This well was assumed to be producing from a reservoir with hydraulically created horizontal fractures (four different systems with fractures were studied). For comparison purposes, additional two-phase flow calculations were made assuming a reservoir with uniform rock properties. The two-phase flow results were also compared with the conventional calculation methods, which do not include the effect of saturation gradients resulting from a simultaneous flow of oil and gas which are normal to this type reservoir. It was found that the conventional methods predict (1) a high and too optimistic value of ultimate recovery, (2) a high producing rate and a high reservoir pressure at a given oil recovery and (3) a low trend of gas-oil ratio with oil recovery. Included in the two-phase flow calculations were provisions to control the oil production rate by an allowable rate and, also, by a gas-oil ratio penalty rule. For the systems with hydraulic fractures, the producing rate was controlled by the gas-oil ratio penalty rule for most of the life. This is in contrast to the system with uniform rock properties which went "on decline" almost immediately. An unexpected characteristic of the systems which included fractures was the early rise in producing gas-oil ratio from 730 cu ft/bbl to approximately 1,200 cu ft/bbl, followed by a "leveling off" before the normally expected gas-oil ratio rise began. Additional features which are a result of hydraulic fracturing are (I) greater ultimate recovery, (2) higher average producing rates and (3) a lower average reservoir pressure at a given oil recovery. INTRODUCTION Some oil fields discovered during the past few years are producing from certain volumetric ally controlled reservoirs (often referred to as solution or internal gas- drive reservoirs) which are characterized by high-pressure drawdown at the wells. Since the available pressure drawdown at a well is limited by the static reservoir pressure and the producing rate is controlled by the available drawdown, wells completed in this type of reservoir usually produce at a rate less than the allowable from the time of completion. Because of this, this type of reservoir is referred to as a low productivity reservoir. Economic considerations require the use of wide well spacing and well stimulation by hydraulic fracturing to make commercial wells in this type of reservoir. Performance predictions for volumetrically controlled reservoirs have been made using a combination of two standard equations. 1. The "Schilthuis" or "Muskat" type material balance equation is used to relate the average reservoir pressure and the cumulative oil recovery. 2. The results from the material balance equation and the productivity factor as described by Pirson' are used to relate the cumulative recovery with producing rate and time. The material balance equation assumed uniform pressure and liquid saturation conditions throughout a reservoir. The steady-state radial flow formula allows for a pressure gradient toward a well but assumes uniform liquid saturation. These calculation methods are adequate for application to reservoirs wherein the drawdown at the well to realize satisfactory producing rates is small compared to the total pressure. In low productivity, volumetrically controlled reservoirs, the pressure drawdown at the well is large cornpared to the total pressure. Although a precise number cannot be given for the magnitude of a large pressure drawdown, values in excess of 1,000 psi would definitely be included. For practical considerations, this usually occurs when the formation flow capacity is less than about 100 md-ft. However, this limit of formation flow capacity will vary with the well producing rate. The low pressure in the neighborhood of the well which results from a high drawdown causes evolution of large volumes of gas. This causes the gas saturation to be higher near the well than at a greater distance—-hence, a non-uniform gas saturation. Also, the relationship between the relative permeability to oil (K/K) and gas saturation is nonlinear but decreases approximately in an exponential way with increases in gas saturation. Because of this, the following chain reaction is established.

IN welcoming the attending members of the Ameri-can Zinc Institute's Ninth Annual Meeting to St. Louis on April 18, the president of the Chamber of Commerce stressed the notable progress that had been made during nine years, marked by many price de-pressions and internal dissensions, while controversies between miners and smeltermen threatened to wreck the organization, prices dropped, and consumption grew languid for want of organized publicity and research. The reports and recommendations of Percy B. Butler, chairman of the Adjustment Committee, and F. C. Wallower, chairman of the Galvanizing Committee, might well be adopted as the institute's objectives. In reply to the speeches of welcome to St. Louis, Arthur Thacher reminded the delegates that the cor-ner stone of progress in the mineral industries was laid by the formation of the American Institute of Mining Engineers in Wilkes-Barre, Pa., in 1871, and the dedication of that organization to the exchange of ideas and methods of the winning of metals and non-metals from their crude state. The activities of the American Zinc Institute constitute, he said, a valuable phase of that work. Mr. Thacher forecast the treat-ment of 1 per cent zinc ore. After the reading of the report of the board of directors, in which Scott Turner and Louis Boschern were named as honorary members of the institute, a survey of world zinc conditions by A. J. M. Sharpe of London was presented. He held pres-ent conditions in China responsible for much of the present depression in zinc. World stocks on, April 1, 1927, were estimated as 52,900 metric tons. Adolph Boldt's paper on "Solidarity in Industry" was followed by a survey of the Tri-State district by Otto Ruhl, who emphasized the importance to the dis-trict of the organization of the Tri-State section of the A.I.M.E., which already has 135 members and asso¬ciates. He also mentioned .that flotation in the Tri¬State field is adding 1500 tons of concentrate to the weekly production. "Mining Economics" was the subject of Julian D. Conover, secretary of the Tri-State Zinc and Lead Ore Producers Association. He gave a detailed report on the costs of mining and milling in the district.

Jan 5, 1927

By R. C. Himes, K. Zanio, J. B. Wagner, J. W. Moody, J. F. Miller, W. Johnson

The recent research with which this paper deals has been concerned with the preparation of pure PbTe crystals suitable for control of radiative processes and othe.v electronic applications. The research has been directed toward the developrnent of methods for the preparation of puve, homogeneous, loul-ca,wier-density PbTe crystals suitable for use in the fabrication of optically pumped and electrically pumped diode lasers. Steps in the preparation of the crystals include 1) purification of the starting materials, 2) synthesis and purification of the PbTe, 3) growoth of PbTe crystals, and 4) adjustt~zertt of composition of the crystals This Paper describes the general preparation procedure employed and discusses some investigntiotzs of purification processes. THE as-received lead and tellurium are nominally 99.999 to 99.9999 pct pure. Assays furnished by the suppliers, obtained by emission spectrographic analysis, show only the presence of about 2 ppm Mg in the tellurium. Such analyses are not very informative, however, since they give no information on the concentrations of normally gaseous impurity elements such as oxygen. Both the lead and the tellurium in the as-received state usually contain appreciable concentrations of oxygen—primarily in the form of oxides on the surfaces of the material. To reduce the oxygen content, the lead is held in the molten state in hydrogen at -700°C for several hours. For this treatment, the lead is contained in a graphite boat which is rf-heated, and the hydrogen is passed through a liquid-nitrogen trap prior to use. Tellurium is subjected to multiple distillation in hydrogen to remove oxygen and other foreign impurities. If, in conducting the distillation, approximately the last 10 pct of the charge at each "stage" is left as the discard cut, purification of the tellurium proceeds as indicated in Fig. 1.l Tellurium used in this work has been distilled two or three times to reduce carrier concentration to about 10" per cu cm. The PbTe is prepared from the purified elements by reacting them in the molten state in sealed, evacuated, or hydrogen-filled silica ampoules. The charge is usually held above the melting point of PbTe (923°C) at 1000 C for 24 hr to ensure that it has been homogenized. Two methods have been employed for the growth of the required single crystals of PbTe: growth from the melt, which will be discussed first, and growth from the vapor phase. Large single crystals of p-type PbTe can be grown readily from the melt by the Bridgman method. For this method of crystal growth, the PbTe is synthesized in situ from proper proportions of the purified elements. Growth (dropping) rates in the range 1.3 to 6.5 mm per hr are employed. Material near the maximum melting composition (about 50.012 at. pct Te) is utilized to avoid composition change on freezing, and thus to obtain crystals of nearly uniform composition. Crystals prepared by use of procedures described up to this point were sufficiently pure and perfect that they could be used for the preparation of laser crystals in studies at Lincoln Laboratory.2-5 ADJUSTMENT OF COMPOSITION Good n-type crystals of PbTe cannot readily be grown from the melt. Further, growth from the melt of crystals of any compositions (n or p type) other than those near the maximum melting composition is difficult because of the large composition changes that must occur on freezing.'" However, melt-grown crystals can rapidly be brought to other desired compositions by isothermal equilibration through the vapor phase with a two-phase Pb-Te stock material, essentially as described by Brebrick and Allgaier.1 The work to be discussed has been concerned with the preparation of n-type crystals; thus, the two-phase stock which was employed contained excess lead, and all ensuing discussion is of the preparation and properties of n-type crystals. The equilibration was designed to the shift composition to the lead-rich limit of stability at the selected temperature. Initial treatment of the crystals at high temperature was employed to minimize the total time required for the equilibration. Final adjustments of the composition and state of the crystals were made by use of low-temperature heat treatment at temperatures in the range 200" to

Jan 1, 1968

By R. C. Buehl, M. B. Royer

High manganese slags of low phosphorus and iron content are produced by air oxidation of high phosphorus spiegeleisen in a basic-lined converter. Control of phosphorus and iron within specification limits for ferromanganese ore feed is obtained by a unique cyclic operating procedure. Various types of slags, or synthetic manganese ore, can be made. AN affiliated paper' describes the production of high phosphorus spiegeleisen containing 14 to 23 pct Mn and up to 4 pct P in an experimental blast furnace from open-hearth slag or manganiferous iron ore. This phosphorus content is too high for use of the spiegel in normal steel-production operations. Consequently, a preferential separation must be effected whereby the manganese is concentrated in a product that is usable in industrial operations. The preferential separation methods being investigated for this phase of the work are confined to pyrometal-lurgical processes for ready incorporation into steel-plant operations. It is fortunate that manganese is more actively oxidizable than iron or phosphorus, and therein lies a preferential separation method for isolating manganese from these two elements. Silicon is more strongly oxidizable than manganese, and its oxidation precedes, or occurs simultaneously, with manganese. Therefore, manganese and silicon are separable into a high manganese oxide slag phase while the phosphorus and iron remain in the molten metallic state. Complete separation of these elements represents an ideal condition which is not generally attainable in actual operations. This pyro-metallurgical method for separating manganese from phosphorus and iron by preferential oxidation was investigated by blowing 500 lb of metal in a basic-lined vessel to obtain preliminary information on the effectiveness of the procedure. Certain conditions of attainment in the separation process are desirable in any method for removing manganese from high phosphorus spiegeleisen, such as: 1—High recovery of manganese in the oxidation product; 2—the product to be of equal or better quality than ferromanganese-grade ore—48 pct Mn minimum, less than 10 pct SiO2, and Mn-P ratio of 300:1; and 3—attainment of the enumerated objectives in a product amenable to industrial handling, such as a slag of high manganese content that will flow from the processing vessel and of sufficient fluidity for ready separation of metallic granules that may have become mixed with the manganese slag phase. Previous Work Recovery of manganese from low grade ores and industrial byproduct slags by smelting to spiegeleisen, with subsequent oxidation to synthetic ferro-manganese-feed ores, has been a subject for periodic investigation during the past four or five decades in the United States and Germany. Joseph' and associates of the Bureau of Mines North Central Experiment Station, Minneapolis, Minn., smelted manganiferous iron ores of the Cuyuna range, Minn., to spiegeleisen and subsequently tried air and ore oxidation procedures for concentrating the manganese into synthetic ferrograde manganese ore. Joseph's results on the operation of a side-blown basic-lined converter for air oxidation of manganese from molten spiegeleisen were so discouraging that the procedure was abandoned after 11 blowing tests. Much slag was thrown from the converter vessel; phosphorus content was four to five times the maximum allowable for ferro ore; and a manganese-iron ratio of only 2 or 3:1 was obtained in the slag instead of the required 8:1. Oxidation of manganese from spiegeleisen with about 0.5 pct P, by adding iron ore to molten spiegel in an experimental open-hearth furnace, proved moderately successful in Joseph's experiments. The main drawback to the operation was the necessity for over-oreing for effective oxidation of the manganese with consequent too high iron oxide residual in the slag. Furthermore, the phosphorus content was proportional to the iron concentration and therefore much too high, so that several hours of reduction by a carbonaceous material were required to adjust the iron and phosphorus to the desired content of high grade ferro feed. A troublesome feature of the slag product of the spiegel oxidation process was its lack of fluidity if the silica content was less than 10 pct, the concentration considered desirable for the synthetic ore. Approximately twice the desired concentration of silica was required to impart enough fluidity for transfer from the vessel by pouring. The acute shortage of manganese in Germany

Jan 1, 1953

By J. E. Gruzleski, O. Knacke, M. J. Meixner

The evolution of CO from small specimens of solidifying steel was investigated using a thermobalance technique. Gas evolution begins in the temperature range between 1400" to .1450°C. This behavior is independent of the initial carbon content and the cooling rate. At a constant temperature above 1220°C, the rate of gas evolution is temperature independent. Out-gassing of the specimen is thought to proceed through small channels formed by the coalescence of bubbles between dendrites. LIQUID metals have a higher solubility for gas than the solid. During freezing, these gases form bubbles which may either escape or remain trapped in the solid. Recent work1 on the evolution of oxygen from solidifying silver showed that the gas is not liberated until a large fraction of the melt has solidified, and that the gas is evolved in an almost explosive manner. Because of the commercial importance of CO evolution in solidifying steel, a similar investigation was undertaken to study the mechanism of gas liberation in steel. EXPERIMENTAL The thermogravimetric method of Knacke and eixner1 to follow gas evolution by weight changes was employed. Weight differences of 0.1 mg could be reproducibly measured on specimens weighing 2.5 g. These specimens were taken from alloys with varying carbon contents from <0.01 to 0.11 wt pct and <0.01 wt pct of each of silicon, manganese, and aluminum. Specimens contained in 8 mm ID magnesium alumi-nate crucibles were heated to 1550°C under 1 atm of very pure (99.995 pct) CO with a tungsten resistance furnace. The specimen temperature was measured with a Pt-Pt/Rh thermocouple located directly beside the crucible. It is felt that the temperature thus measured was within 5" to 10°C of the specimen temperature since on fusion the weight of the specimen increased due to uptake of CO, and this weight increase was always observed to begin within the temperature range of 1530" to 1540°C. Even after 3 hr there was a small weight increase with time indicating that the molten specimen was not completely saturated with CO. Therefore, complete saturation was not attempted, and all specimens were simply held for 3 hr at 1550°C before cooling. Two types of cooling experiments were performed. One consisted of continuous cooling at linear rates from 5°C to 20°C per min down to 1020°C. The second type of experiment involved continuous cooling at 10°C per min to a predetermined temperature, and then holding the specimen at this temperature for a certain time. During all of these experiments, the sample weight was recorded as a function of time and temperature. OBSERVATIONS Continuous Cooling Experiments. No gas evolution was detected above 1450°C. The initial weight decrease always occurred between 1400" and 1450°C with the average at 1430°C. With further cooling, gas evolution continued to about 1150°C. Between this temperature and 1020°C no further outgassing was observed. This behavior did not seem to depend on the initial carbon content nor on the cooling rate in the range investigated. Typical patterns of gas evolution are shown in Figs. 1 and 2 for different initial carbon levels and cooling rates. The total amount of gas liberated during solidification varied with the rate of cooling. The total weight change on continuous cooling at a rate of 10°C per min

Jan 1, 1970

By C. R. Breck

THERE has been a running discussion over the-past several years with respect to the life and adequacy of our natural gas reserves.. Some of the experts agree on one phase of the subject at least--that eventually it will be necessary to augment deliveries of natural gas in the northern markets by the development of a more or less comparable synthetic gas made from coal. The purpose of this paper is to point out: 1. It may be later than a good many people think-the demand for additional domestic and commercial pipeline gas in at least one section of the North will probably be felt rather keenly before an adequate synthetic pipeline-gas project, developed on economic lines, could be completed, even if &apos; initiated in the near future. 2. The evidence is considerable that such a project would be technically sound and economically self-supporting, although the margin of profit at first might be so small and the magnitude of an economic enterprise so great that financing would be impossible without Government aid in some form or other. The part of the country referred to is the heavily populated section in the northeast of the United States. To simplify an examination of the situation, let us take the potential marketing areas within range to the north and east of the three pipelines: 1. Tennessee Gas Transmission Co. as it enters Erie County, New York state. 2. Texas Eastern Transmission Corporation just before the tap that supplies the general Philadelphia area. 3. Transcontinental G& Pipe Line Corporation as it enters the state of New Jersey The sources of gas for these three pipelines are in Texas and Louisiana. The ultimate maximum combined capacity of the three lines at the points stated is approximately 1,200,000,000 cu ft per 24 hr at the maximum load factor probable of attainment in normal operation. The areas supplied by the three lines north and east of the points stated, or assumed as eventual markets, are: 1. Central New York state, from Buffalo to Albany (both inclusive).

Jan 1, 1953

By G. R. St. Pierre, S. W. Gilby

The equilibrium vapors established over Fe-Cr-Ni alloys containing up to 50 pct Cr at 1600°C were determined by collecting the effusate from thoria Knud-sen cells. From these data, the activities of iron and nickel in the ternary alloys have been calculated. In a separate set of measurements, a mass spectrometer was used to determine the activities of the three components in a series of Fe-Cr-Ni alloys. In binary Ni-Cr melts, the activity coefficient of chromium referred to pure solid chromium as standard state is less than one at low chromium contents but is greater than one for melts containing more than 30 at. pct Cr. For Ni-Cr melts containing less than 10 at. pct Cr, In ?Cr = 0.15-0.92 N2. Ternary activity diagrams for Fe-Cr-Ni alloys are presented. In iron-rich alloys, the interactions between the three components are negligible; however, in nickel-rich alloys, the three principal interactions have significant positive values. THE activities of components in binary Fe-Ni alloys have been measured both in the solid solution1-3 and liquid solution4-6 temperature ranges. The determination for Fe-Ni melts have been made by three different methods: transpiration,4 Knudsen-cell effusion with analysis of an accumulated condensate,&apos; and Knudsen-cell effusion with direct measurements of relative component intensities by mass spectrometric methods.6 The results obtained by the three different methods in three different laboratories are in excellent agreement and considerable confidence is placed in the activity coefficients for Fe-Ni melts. At 1600°C, the activity coefficients in dilute solution are ?°Ni = 0.66 and ?oFe = 0.40 for the pure liquid components as standard states. Measurements made on solid solution Fe-Cr alloys7-10 indicate that the component activities are slightly greater than ideal. The measured activities in iron-rich Fe-Cr liquid alloy11-16 indicate almost ideal behavior for this system. The recommended activity coefficient of chromium in dilute solution in liquid iron at 1600o C, ?oCr, is 1.18 when referred to pure solid chromium as standard state and 1.04 when referred to pure undercooled liquid chromium as standard state." The conversion factor of 1.14 is based on a melting point of 1857°C and an enthalpy of melting of 4047 cal per g at. for chromium.21,37 The activity coefficient of iron in dilute solution in liquid chromium has not been measured. Activity measurements on solid Ni-Cr alloys have been made by several investigators.17-20 During the review of this manuscript, Fruehan12 published the results of a study on liquid Ni-Cr alloys at 1600°C. He used galvanic cells22 with ZrO2(CaO) as the electrolyte and Cr/Cr2O3 for the reference electrode. His results indicate that ?oCr in nickel at 1600°C is about 1.01 when referred to pure solid chromium and about 0.89 when referred to pure undercooled liquid chromium as standard state. The activity coefficient of nickel in liquid chromium is unknown. The compositions of vapors freely evaporating from some molten Fe-Cr-Ni alloys have been measured by Lyubimov, Granovskaya, and Berenstein.23 Their results, combined with known vapor pressures, indicate strong positive deviation for chromium in iron-rich alloys and strong negative deviation for chromium in nickel-rich alloys. EXPERIMENTAL PROCEDURES This research was undertaken to determine the activities of components in ternary Fe-Cr-Ni melts containing up to 50 at. pct Cr. At the initiation of the research, we decided to use a Knudsen-cell method wherein a portion of the effusing vapor is condensed on a cold plate.&apos; The composition of the equilibrium vapor for each alloy composition is determined in this method by holding the system under constant conditions for a period of time sufficient to collect enough condensate on the cold plate for chemical analysis. The activities of components in ternary alloys can be calculated from such vapor composition determinations by Eq. [1].24

Jan 1, 1970

By B. C. Allen

Surface free energy and surface self-diffusion of solid molybdenum were studied in the temperature range 1600" to 2400°C using pressure-sintered bi-crystals. Comparison of groove angles formed in various surfaces perpendicular to the grain boundary indicate a maximum of 1 pct variation in surface free energy with crystallographic mientation. This anisotropy tends to decrease with increasing temperature. The surface diffusion of the bicrystals is equivalent to that of sheet with a mild (100) Preferred orientation. Anomalously low values found for bi-crystals with surface orientations of (OOl), (012), and (011) are rationalized in terms of anisotropy in surface free energy. THE effect of crystallographic orientation on surface free energy1,&apos; and surface self-diffusion3,4 has been primarily studied in fcc metals. The object of this work was to study the effect of orientation on surface diffusion and surface free energy of bcc molybdenum using pressure-sintered bicrystals. EXPERIMENTAL WORK Materials and Crystal Preparation. Arc-melted molybdenum rod was obtained commercially and electron beam zone refined at 50 cm per hr at 10- 5 torr to form single crystals about 8 cm long and 0.65 cm diam. Three crystals were prepared with axial orientations about 1 deg from [001.], [011], and. [111]. To reduce the carbon content, the crystals were annealed 2 hr in 1.4 atm flowing wet hydrogen at 2050°C. Then the oxygen content was reduced by annealing for 2 hr in -30°C dewpoint hydrogen at 2020°C. The resulting impurity analysis is given in Table I. Bicrystal Preparation. The single crystal rods were cut into transverse slices with a thin silicon carbide abrasive wheel to produce specimens about 0.6 cm long. They were mounted in epoxy and surrounded by stainless steel washers. Cutting in half was done longitudinally at various angles to known crystallographic planes containing the cylinder axis according to Fig. 1. To reduce surface deformation resulting from the cutoff wheel and thus reduce parasitic grain boundary formation on subsequent annealing, about 0.003 cm was manually ground off each cut surface with 600 grit paper. Care was taken to keep the surface flat. After removal from the mounts, one half was generally ro-tated 180 deg with respect to the other to give a po- tential symmetrical tilt grain boundary between the two halves. In the other cases when low misorienta-tion angles were desired, the crystals were not rotated. On the basis of symmetry, sufficient bicrystals were prepared to cover the entire range of misorientations for symmetrical tilt boundaries. The misorientations, +, ranged from 0 to 45, 0 to 90, and 0 to 60 deg for [001], [011], and [111] bicrystals, respectively. One [Ill] twist bicrystal was prepared from 2 single crystal discs rotated 17 deg relative to each other. Each specimen consisted of two pieces which were placed in a cylindrical tantalum can. Sharp edges were rounded and the fit was made as snug as possible to reduce subsequent deformation during bonding. The assembly and crystals generally were vicuum outgassed at 900" or 1700°C and then electron beam welded in the can at l x 10-4 torr. After being leak checked, the samples were placed in an autoclave and hydrostatically gas-pressure bonded5 in four batches under helium at 10,000 to 18,000 psi at 1650°C for 3 hr. Satisfactory bonds were obtained in many cases, and most of the crystals bonded after two exposures. The results did not appear to be affected by the various pressures used, preannealing conditions, crystal orientation, or time-pressure-temperature route taken to the final bonding condition. After bonding, the tantalum cans were selectively removed in cold concentrated HF. Measurements indicated overall deformation was under 1 pct. The bicrystals were metallographically ground and polished flat and perpendicular to the axis. Examination showed the boundaries were straight and almost free of parasitic grains caused by extraneous local deformation. Annealing. In preparation for thermal grooving, the bicrystals were cleaned and annealed by outgassing at 10-5 torr at 1900°C and heating at 2300°C under 1 atm 99.996 Ar for 0.5 hr. The crystals were held in a closed 4-deck box made of molybdenum sheet, and were heated in a Ta-1OW resistance furnace. The ar-

Jan 1, 1970

By F. N. Speller

Interest in the corrosion problem seems to continue without abatement and is bringing practical results. At least four important conferences on this subject have been held during the last 5 months. Those interested in steel-frame structures are taking steps to study vulnerable points on account of the failure of some minor parts in certain buildings after 35 years of service. The steam power-plant group, including the railroads, realize the importance of a better knowledge of corrosion, especially under modern high-temperature boiler operations. The chemical and refrigerating industries have already conducted a systematic study of depreciation of metals by corrosion, for which they have spent considerable money and time during the last 2 years with encouraging results. More has probably been done to control corrosion in the atmosphere and in closed water systems, because the work on these phases of the problem started over 15 years ago and the important factors are now fairly well understood. As a result of all this work, there is now little excuse for corrosion in water conduits, recirculating condensers and cooling systems, since economical means of prevention have been worked out to meet nearly all situations where such corrosion occurs. The entire Baltimore water supply was treated with lime at a cost of only 35 c. per million gallons and the rate of attack on the pipes has been reduced to not over 20 per cent. of what it was before the treatment. Yearly damage to water mains in Baltimore is estimated at $300,000, and in New York City at $5,000,000, not including damage to water conduits in buildings. In some cities corrosion is now recognized by water works&apos; engineers as a major problem. In the oil industry, there are evidently three general classes of corrosion, relating to: (I) Production, (2) transportation, and (3) refining. (1) Production.—Some fields, those of California for example, have little corrosion trouble in the wells. In others this is a major problem and should be a strong incentive to the development of more resistant metals at a reasonable cost. E. G. Woodruff,&apos; consulting geologist, has pointed out that more of the oil of the future will probably come from the

Jan 1, 1927

By Gilbert P. Moore

Petroleum operations in Bolivia are still limited to those of the subsidiaries of the Standard Oil Co. of New Jersey. Development work is being carried on at Sanandita and at Bermejo and testing operations in the north. Five wells have been completed at Sanandita. Wells 1 and 2 are producers, 3 and 5, which are north of 1 and 2, are poor wells, and well 4, to the south, was dry. In the Bermejo field, well 5 has just been completed. No information as to the production is obtainable. In the north one string was operated at each of the following locations: Machareti, Camatindi and Camiri. The well completed at Machareti during the year was a failure. The result of the others is not known. It is reported on good authority that a pipe line will be completed in 1931 to connect the Sanandita field with the Lomitas field in the Argentine. This will place Bolivia among the ranks of the producing countries of South America for the first time. This development indicates that some arrangement has been arrived at with the Argentine Government for the importation of Bolivian oil. During 1930 the Bolivian Government declared in effect the new Petroleum Law which had been expected for such a long time. One of the first acts of the military junta, which rose to power through a coup d&apos;état, was to cancel this law, so that Bolivian oil operations are still under the old law of 1921. One new local company was formed to exploit 1,500,000 hectares near the town of Cochabamba. The Bolivia Concessions, Ltd., which had a concession permitting the selection of 17,000,000 acres in eastern Bolivia, is reported to have failed in 1930 and is now being liquidated. Chile During 1930 the Chilean Government entered into a contract with an individual to explore in five distinct zones of the Republic. According to the contract, geologists must be at work there by May 1 of this year and a well must be started by the end of 1931. If the operations are

Jan 1, 1931

By W. P. Haynes

No wildcat operations are recorded from France during the past year, and no new discoveries have been made. In northern Africa, in Morocco, some prospecting continued in the Gharb and Tselfat regions. Only very small production or shows were found. At the close of the year one cable-tool well (depth 400 meters) was drilling in the Tselfat district, and one rotary well in the Gharb. In Tunisia one well was drilling at Sloughia. Refinery building has been active under the new petroleum law, no less than six plants now being under construction. At Pechelbronn, it is estimated 130 wells were drilled, of which 73 wells, or 56 per cent, were productive. Total drilling was 45,000 m. One new Jurassic horizon was discovered. In the mining area approximately 17,500 m. of new gallery were driven. Production at Pechelbronn for the first nine months was as follows: From wells, 233,013 bbl.; from mines, 164,815 bb1.—a total estimated production for the year of 532,000 bbl. Production at Gabian was 3780 bbl. for the year. In Algeria production from Tliouanet was small, being estimated at 6510 bbl. This production is from Helvetian sands (Miocene) around a salt plug. Italy Production for the year was 211,500 bbl., an increase of 62 per cent over that of last year. Drilling to the extent of 97,000 ft. was done mainly by the A. G. I. P., the government company in the Province of Emilia. More locations are being tested in this area, where geophysical results have shown indications of buried uplifts. Oil has been encountered on two of these structures, at Fontevivo and Podenzano, but the wells have given trouble with salt water. The chief producer is the Societa Petrolifera Italiana at Salsomaggiore and Valezza. The production is from sand lenses at relatively shallow depths. New concessions of 2000 hectares were granted at several points in the Po Valley, and geophysical work is being carried on. The A. G. I. P. is working on a five-year program of exploration to test new areas.

Jan 1, 1933

By G. J. Lindenburg, T. L. Wilson

The Velvet uranium mine is located in the Big Indian district of the Colorado Plateau. The uranium ore body lies within the lower Triassic Chinle Formation, and the ore is associated with west-south- westerly trending fluvial sand systems. Exploration and mining are directed by longhole drilling and radiometric sampling. Results of the gamma probing, face scanning, and geologic mapping guide mining decisions and planning. Three people are directly involved with the geologic procedures: two geologists and a mine supervisor. The two geologists map, do rib scans, and direct longhole drilling. The third man involved, the mine supervisor, has last minute directive action based on shot hole probe data.

Jan 1, 1984

By D. C. Hilty, W. Crafts

A qualitative pseudoternary solidification diagram for the Fe-S-O system modified by manganese is proposed and supported by experimental derivation of an isothermal section at 1475°C and substantially 1 pct Mn in the solid-metal phase. The solubility of oxygen in liquid iron containing 1 pct Mn and sulphur contents up to 0.9 pct has been measured at 1600°C and found to increase as the sulphur content exceeds 0.15 pct. AS has been pointed out previously,&apos; all oxide and sulphide inclusions in steel, excluding mechanically entrained matter, result from modifications of the basic Fe-S-O system. Therefore, one method of attack on the problem of the mechanism of deoxida-tion and inclusion formation is to examine the influence of deoxidizers on the Fe-S-O liquidus diagram. This approach has been adopted in work on the subject being carried out at the Metals Research Laboratories of the Electro Metallurgical Co. and has resulted in the postulation of types of solidification diagrams for the Fe-S-O system modified with common deoxidizers. This method has been of considerable assistance in interpretation of the factors affecting the formation of inclusions.&apos; For the most part, however, these diagrams have been highly speculative. They were constructed primarily by inference from the pertinent binary and ternary systems and from the appearance of inclusions produced by specific deoxidizers. Moreover, since the systems contain four or more components, simplifying assumptions and qualifications were necessary in order to permit their representation as modifications of the Fe-S-O diagram. Consequently, experimental confirmation of the type of construction employed for these diagrams is desirable, and the present paper is concerned with such evidence. The addition of manganese to the Fe-S-O system was selected for initial investigation. Manganese is an important component of practically all steel and is, therefore, of fundamental interest. Because of its great affinity for sulphur, manganese has a more profound effect on the sulphide side of the Fe-S-O diagram than any of the other common deoxidizing eletments. In addition, more quantitative information pertaining to the contiguous binary and ternary systems involving iron, manganese, sulphur, and oxygen is available than for the other deoxidizers. Fe(Mn)-S-O Solidification Diagram Many of the side diagrams of interest in connection with this system are known. The Fe-Mn binary has been well established by several investigators;% the Fe-O system has been clarified by Darken and Gurry;&apos; and FeO-MnO diagrams have been published by Herty,5 Andrew, Maddocks, and Howat,6 and by Hay, Howat, and White.7 The Mn-O diagram does not appear to have been derived experimentally, but the portion of &apos;it that is of interest can be visualized easily from a consideration of the melting points of Mn and MnO and the fact that a broad miscibility gap must exist between them. The ternary Fe-Mn-O diagram has been discussed by Benedicks and Löfquist,8 Wentrup,9 and by Körber and Oelsen.10 Experimental study of the Fe-Mn-O system has been carried out by Körber and Oelsen and to a lesser degree by Chipman, Gero, and Winkler,11 Hilty and Crafts," and others. On the basis of published information, then, an outline of the Fe-Mn-O liquidus diagram can be constructed as illustrated by Fig. 1. In this, as in all succeeding diagrams, transformations such as the ?-? reaction in iron have been ignored for purposes of simplification. The arrows denote falling temperature. The distinguishing feature of this diagram is the broad region of liquid immiscibility extending

Jan 1, 1955

By G. M. Schwartz, G. A. Thiel

THE first record of the quarrying of dimension stone in Minnesota dates back to 1820 when limestone was quarried locally for part of old Fort Snelling. Limestone quarries were operated at Stillwater, Mankato, and Winona as early as 1854. Granite was quarried first at St. Cloud in 1868, and within a few years thousands of tons were shipped to widespread points. Rough dimension stone for large buildings furnished the first important market, but beginning in 1886 paving blocks were in demand. The largest shipment was in 1888, when 1925 cars were shipped from the St. Cloud area. Quartzite was quarried first at New Ulm in 1859 and somewhat later at Pipestone and elsewhere in southwestern Minnesota: The productive dolomite quarries at Kasota were opened first in 1868 and have continued as large producers of a variety of stone to the present time. At present, the industry is controlled by relatively few operators, and for that reason detailed figures on dimension stone are not released for publication. A general idea may be obtained from the data in the Minerals Yearbook for 1948. The figures for total stone produced in Minnesota are 1,804,000 tons valued at $5,090,652. Probably the largest item in the latter figure is received from dimension stone. A better idea of the situation, in relation to the country as a whole may be gained by using the data for 1930 when more companies were operating in Minnesota, and complete figures were published. In that year Minnesota produced granite valued at $2,668,119 and ranked third among the states in value. Minnesota&apos;s production of granite was almost exclusively for dimension stone. In the same year Minnesota produced 300,000 tons of limestone (dolomite) valued at $840,860, and this likewise was mainly dimension stone. In finished limestone Minnesota ranked second among the states in 1930. Sandstone and minor amounts of quartzite are the only other dimension stones that have been produced in Minnesota, but the quarries are now inactive. The commercial stones of Minnesota have been described in two reports by Bowled and by Thiel and Dutton.2 The early history of quarrying in Minnesota and extensive notes on the various rocks are given by N. H. Winchell.3 Small limestone and dolomite quarries were numerous throughout the area of Paleozoic rocks in southeastern Minnesota. Early production was largely dimension stone. With the increased use of Portland cement, most of these ceased production, and today only those at Kasota and Winona remain in operation. In recent years many quarries have reopened and new ones started, but these are devoted to the production of crushed rock and agricultural lime. As the application of modern quarrying and finishing methods increased, small companies in the granite business have dropped out, and the remaining companies have modernized their plants, purchased old quarries, and opened up new ones, thus furnishing a wide variety of granites suitable for most of the customary uses. It is the purpose of this review to present notes on&apos; the geology and operations of each of the quarries now operating within the state. Granites and Related Igneous Rocks The term granite as used in this report includes granites, gneisses, diorites, gabbros, and other igneous rocks. The granites of greatest economic importance are found in three widely separated regions, see Fig. 1. 1-Central Minnesota in the region of the city of St. Cloud, 2-the upper Minnesota River valley region, 3-the northeastern portion of the state, commonly referred to as the Arrowhead region. The St. Cloud Region: The rocks of the St. Cloud region are mainly granites and related rock types such as monzonites and quartz diorites. The stones may be grouped into three major types, namely, pink granite, red granite and gray granite. Most of the pink granite occurs in the area to the southwest of St. Cloud. The rock is best described as stone with large pink crystals set in a finer grained black and white background. The minerals of the matrix occur in remarkably uniform sizes, and the pink crystals are sufficiently uniform in. their dis-

Jan 1, 1952

By Leon Merker

FLAME fusion growth of strontium titanate crystals was undertaken to obtain large transparent crystals on which physical data could be gathered. The fact that strontium titanate is a cubic crystal and probably has a high index of refraction indicated that it might be useful in optics. No large boules* of strontium titanate had been synthesized previously, and none have been found as natural occurrences. The flame fusion process, invented by Verneuil in 1904,1 was first applied to grow large crystals of ruby and has since been used extensively to grow crystals of corundum and spinel on a commercial scale. Only during the past nine years has this technique been applied to the growth of large single crystals of other high melting compounds such as rutile,2 mullite,3 and ferrites4 One of several significant advantages of the flame fusion technique over more conventional methods of growing crystals from a melt is that the crystals are grown without the use of melt containers. This fact alone excludes other methods of growing crystals from a melt whenever there are compounds with a melting point near 2000°C or above. Growth of the crystal, similar to that of a stalagmite, takes place inside a circular refractory furnace that does not contact the crystal, Fig. 1. This eliminates a serious source of impurities as well as the likelihood of multi-crystalline solidification along the container walls. The flame fusion technique is particularly advantageous for research because it produces large crystals quickly and at lower cost. A corundum crystal 25 mm long and 12 mm in diam can be grown in 2 to 3 hr. Operating conditions permit observation of the growing crystal during any stage of the process. The various flame patterns and a wide range of oxidation-reduction conditions can be investigated in a relatively short time. It should be pointed out that formation of the foot of the boule is the most critical step in growing an unfractured boule. When the tip of the sintered cone is fused to initiate crystal growth, the original area of fusion should be kept as small as possible so that one crystallite can assume dominance over all the others and propagate as a single crystal. If the boule start happens to consist of several crystals, usually the entire boule also contains several crystals. In many cases these tightly cohering crystals exhibit different crystallographic orientations. Although the basic technique of the original Verneuil process has been retained, refinements in method and burner design have been developed in recent years. For example, boule growth may be initiated on a seed crystal rather than by fusion of a sintered cone. The danger of multicrystalline or twinned boule starts is thus eliminated, and this procedure may also be used to grow boules of predetermined crystallographic orientation. Prior Art: Of the many attempts to produce artificial gem crystals, most early efforts% ere directed toward synthesis of .rubies and sapphires and diamonds. None of these efforts resulted in a process that was commercially practical. Without exception only tiny crystals of corundum were obtained, and those at excessive cost. Verneuil announced his process in 1904; Ravier6 in 1934 presented a detailed description of a commercial boule production plant. Descriptions of the German synthetic stone industry, the process details, and the equipment used have been published by Barnes7 and by Merker.&apos;

Jan 1, 1956

Soil Testing for Engineers. By T. W. Lambe. Published by John Wiley & Sons. 165 P. $5.00.-Filling a need for a text for the teaching of soil testing in the laboratory, this book is also of value as a reference for practicing engineers and for personnel in soil laboratories. Following an introductory chapter on general laboratory procedures are chapters devoted to the individual laboratory soil tests which are commonly employed. Apparatus, supplies, recommended procedures, discussion of procedure, calculations results, and numerical examples are provided for each test. Brief derivations of formulas and explanations and discussions of calibration procedures and special techniques are given in the appendix. Mesabi Pioneer. Copyrighted 1951 by the Minnesota Historical Society.- Publication of this book has been made possible by a generous gift to Society from the E. J. Longyear Co. of Minneapolis. This book covers the evolution of the Mesabi Range from a wilderness into the nation&apos;s greatest iron producing area. In this book is found the first hand experiences of Edmund J. Longyear who saw the development of the range from its beginnings, and who himself took a notable part in it. In 1890 Edmund J. Longyear sank the first diamond drill hole on the Mesabi. During the next two decades he sank pits and holes- 7133 of them-throughout the length and breadth of the Mesabi Range, exploring for iron ore. He saw roads and railroads built. He watched the range communities--Hibbing, Chisholm, Biwabik, Mountain Iron and the others change from exploration camps to

Jan 11, 1951

By R. Bakish, C. S. Barnett

IN experiments on tantalum strained in tension, Bechtold did not observe deformation-twinning even at a temperature as low as that of liquid air.&apos; This is an unexpected behavior for a metal of body-centered-cubic structure. Therefore, it is desirable to determine whether the lack of twinning is an inherent characteristic of this particular metal, or whether the reluctance to twin can be overcome under suitable conditions. The following experiments were performed under conditions favorable to twinning and cleavage in their competition with slip, namely, with impact loading on large-grained sheet at low temperatures. The crystallography of cleavage in tantalum sheet was also investigated carefully because of the remarkable ductility of tantalum at low temperatures and because recent tests on oxygen-embrittled tantalum had disclosed unusual cleavage behavior for a metal of this structure: cleavage primarily on (110) planes and only occasionally on {100}.2 The tantalum, supplied by Fansteel, was of 99.9 pet purity, with the chief impurities being iron (0.03 pet) and carbon (0.03 pet). Coarse grains were produced by the strain-anneal method, the anneal being 4 hr at 2000°C in a vacuum of 10-3 mm Hg, followed by furnace cooling. Impact deformation was applied in various ways: a) by hammer blows on an anvil, the specimen and anvil being immersed in liquid nitrogen ( —196°C), b) by driving a precooled center-punch into the sheet, and c) by bending around a crystallographically determined axis with a hammer blow. The impact-deformation produced bands and slip lines on the surface, Fig. 1. The bands have every appearance of being deformation twins, a) They are tilted with respect to the untwinned surface. b) They have the appearance of Neumann bands in iron, thin lens shape, some having serrated edges. c) The orientation in each is different from that of the surrounding matrix and uniform within a given band, see slip lines within them in Fig. 1. d) Upon repolishing and etching, the difference in orientation and the resemblance to Neumann bands is again evident, Fig. 2. (In this micrograph the slight bend in the bands as they cross grain boundaries was noted frequently and results from the high degree of preferred orientation in the sheet.) e) The bands persist after annealing treatments that would have removed them had they been a low-temperature martensitic phase, e.g., after an anneal of 1/2 hr at 900°C. When back-reflection Laue data were plotted for single-surface analysis of several grains, every trace of the bands in each grain could be explained by (112) planes. In addition, two of the bands were located in space by traces on two surfaces, and these also were found to lie on (112) planes within the error of the stereographic plot. Since (1 12) is the anticipated composition plane for deformation twins in body-centered-cubic metals it is felt that the observations listed above are conclusive evidence for the identification of the bands as twins. Similar tests with impact at —77° and at 25°C produced no twinning. It is concluded that the critical shear stress for slip at the rates of straining used was always low enough to prevent the applied stress from reaching the value required for twinning at these temperatures. It was noted that the serrations along the edges of the twin bands exhibited parallel crystal facets. Several similarly oriented notches are visible in Fig. 1, and a remarkable set is shown in Fig. 3. It appears from Fig. 1 and similar areas that notches are frequently associated with the intersection of a slip line with a twin, although not all such intersections are at notches. In some instances a slip line appears to enter the twin, cross it, reflect from the opposite side and recross it, producing a pattern resembling a notch but without producing the notch itself, see Fig. 1. It is suggested that the stress concentration at the end of a slip line is responsible for these details. The strain energy associated with the pile-up of dislocations at a twin boundary may be lessened by untwin-ning or failing to twin a portion of the twin band, or

Jan 1, 1959

By Robert J. White

Strong&apos;s equation for calculating bottom-hole pressure reduction due to gas cutting of drilling mud is corrected, resulting in a simpler equation which is easier to use. Use of the equation is illustrated by examples. It is shown that reduction of weight of a 10 lb/gal mud by 50 per cent at the surface due to gas cutting produces only n 3 per cent decrease in hydrostatic head at the bottom of a 5,000-ft well. It is also shown that at the surface 5 volumes of air per volume of mud are required to reduce the apparent mud weight from 8.5 to 6.5 lh/gal in a 3,000-ft well. Illustrative graphs are included to show the effect of various degrees of gas cutting on apparent mud weight at depths of 2,000, .5,000 and 10,000 ft and to show variation of apparent mud weight, with depth for a 100 lb/cu ft (13.37 lb/gal) mud gas cut to 90 lb/cu ft (12.03 lb/gal) at the surface. INTRODUCTION In 1938, Strong&apos; published the following equation for calculating reduction in bottom-hole pressure due to gas cutting of drilling mud h = 1/D [p + pn/100 In p + p(1-n/100)/p(1- n-100)] where: h = depth in feet P = pressure in atmospheres at depth h due to mud column only D = hydrostatic pressure in atmospheres of a col-umn of uncut mud 1 ft high p = back pressure at well-head (in atmospheres) n/100 = fraction by volume of gas in mud at well-head at back pres-sure p This equation was recently found to contain an error due to an incor-rect expression for variation of vol-ume fraction of gas with pressure. Values calculated by the original equation are close to the correct values for small percentages of gas for which it was derived but become increasingly erroneous as the gas content increases and are completely unusable at the very high gas con-tents employed in aerated mud. DERIVATION The nomenclature used is the same as in Strong&apos;s paper. The pres-sure dP exerted by a lamina of thickness dh at a depth h ft is ex-pressed by Eq. 1 where x = volume fraction of gas at depth h dP = D (l - x)dh . . . (1) When we express x in terms of the wellhead per cent gas n, the well-head pressure p and the pressure P at depth h, the result is Eq. 2. x = (np/p+p)/(100-n) + (np/P + p) When this is substituted in Eq. 1 and rearranged to separate the var-iables the result is dh = 1/D [dp + np/100-n dp/(P + p]. Integration between appropriate lim-its results in or if the wellhead is open so that p = 1 atm and we rearrange Eq. 4, the result is loss in head = hD — P = n/100-n In (P + 1) ...(5) Eq. 5 can be solved easily by successive approximation using hD as a first approximation for P on the right-hand side and calculating a first value for loss in head. This can then be used to get a new value of P using the left-hand side of the equation. Values converge very rap-idly even for quite large values of per cent by volume gas n. EXAMPLES The effect on bottom-hole pressure of 50 per cent gas cutting of the mud in a 5,000-ft well using 10 Ib/ gal mud will be calculated, we have: h = 5,000 ft 10 X 7.48 144 X 14.7 = 0.0353 atm/ft hD = 176.5 atm n = 50 Substituting these values in Eq. 5 and using hD as a first approxima-tion of P on the right, we have, approximate loss in head = 50/50 In (176.5 + 1) = 2.30 log 177.5 = 5.17 atm. We calculate a new value of P as follows:

Jan 1, 1958

By A. W. Fahrenwald, Lewis S. Prater

BY taking advantage of the fundamental difference between screening and classification-namely, that specific gravity has no effect on screening but is one of the important factors in classification-a combination of the two may be used as a process of mineral concentration. Although this fact is not new, so far as is known it has had little or no commercial application. The scheme is not presented now as a process for producing finished products but rather as a preliminary operation rejecting part of the barren material from an ore before it is subjected to more costly treatment. That is largely the function of the new heavy-media concentration processes that have been widely accepted. Original installation costs for the present sink-float processes are relatively high, however, which confines their use to operations where large tonnages are handled. Sink-float has been successful on only the relatively coarse (approximately plus 10-mesh) portion of an ore, and it is in this same range that classification screening can function most satisfactorily. Theoretically, there is no upper limit to the size of particles that can be handled in a sink-float operation, but the degree of liberation in the very large pieces usually limits this. With classification screening, particles from 3/8 to 1/2 in. would be the largest that could be handled, but the lower range could be extended somewhat below 10 mesh. In order to take full advantage of the difference in specific gravities of the minerals being separated, sorting in the classifier should be under as extreme hindered-settling conditions as possible. Laboratory tests have been made on a galena ore and on an artificial mixture of quartz and magnesite to determine the separations that may be expected. Although more than one scheme may be followed, in these tests the separations were made by cutting the underflow from the classifier as a concentrate and then screening the overflow. The screen oversize was rejected as a tailing. Classification was done in a hindered-settling teeter column and screening was done by hand, using the standard [v2]series. The accompanying flowsheet gives the testing procedure followed. [ ]

Jan 1, 1945